INSTRUCTION MANUAL. Model: LUM-RGBUX8. *Optional

Transcription

1 INSTRUCTION MANUAL Model: *Optional

2 Back Terminals of Wall Panel UX8 RGB Touch Panel Input Voltage: Output Signal: Control Mode: Working Temp : Package Size: Weight(N.W.): Weight(G.W.): 5Vdc, 0.5A~1A (with the included transformer) RF 2.4GHz, DMX512 RGBW, 4 Zones Control -30 ~55 L132 W192 H50(mm) 230g 370g Product Size: From the Female XLR Black Wire Green Wire White Wire Alternative Decoders High Voltage (120V) DMX Controller LUM-B34XTS-DMX Female Mini XLR to Loose Model: LUM-B34XTS-FXL Measures 50" in length Alternative Decoders Low Voltage (24V) RGB DMX Hardwired Receiver (Water proof) LUM-DMXWP2 RGB DMX Hardwired Receiver For Model (LUM-B34XTS-DMX) and (LUM-B34XTS-WP2) a Female Mini XLR to loose wire connector is required (LUM-B34XTS-FXL) to connect to color wheel panel

3 Installation Instructions 3. screw the baseplate and the back box in the wall firmly. 4 Connect in a right way and put the power adapter into the back box. 1. Install the Switch J-box into the wall. Typical boxes as below: 2 Use a straight screwdriver to pry the position shown: Transformer (Included)

4 Ke y Functions: 5 Embed the upper touch panel into the base plate and then tap the bottom to press into the slots. Zone Selection Keys Short press: on/select Long press: Speed/Brightness +/- Touch Circle White Key Press: Turn on/ Long press: Dimming Mode Key Scene-mode keys Short press: play Long press: save The Changing Mode (Press to Select ): 1. Static Red 2. Static Green 3. Static Blue 4. Static Yellow 5. Static Purple 6. Static Cyan 7. Static White 8. RGB Jumping 9. 7 Colors Jumping 10. RGB Smooth Transition Colors Smooth Transition 12. Static Black

5 GN D End of Cable End of Cable End of Cable Model: LUM-B34XTS-DMX Model: LUM-B34XTS-DMX Model: LUM-B34XTS-DMX Application Composition DMX512 Signal Output : DMX Output Wiring Low Voltage 24V Lumilum RGB Strip 001 -RC -WF 005 -WF DMX Output Wiring Line Voltage 120V RGB Strip (B34XTS Series) -RC 009 DMX GENERIC CONTROL PANEL OR RF TO DMX MODULE D + D - DMX INPUT DMX OUTPUT Male Input 1: COMMON 2: DMX- 3: DMX+ White: D+ Green: D- Black: GND Female Output LUM-B34XTS-DMX NOTE: FOR DMX INPUT CABLE To Convert 3 Pin Mini XLR to 3 Pin DMX use converter cable Model#: LUM-B34XTS-XLR 1: COMMON 2: DMX- 3: DMX+ DMX CONTROLLER Black: V+ Red: Red Light Green: Green Light White: Blue Light LED Output: VDC / 500W Operating Temp. -20 C C -4 F F Line Voltage Input: VAC A C 100~240V I nput Up to 164ft. of V RGB LED STRIP 013 Up to 164ft. of V RGB LED STRIP DMX INPUT DMX OUTPUT 1: COMMON 2: DMX- 3: DMX+ White: D+ Green: D- Black: GND Male Input Female Output To Convert 3 Pin Mini XLR to 3 Pin DMX use converter cable Model#: LUM-B34XTS-XLR 1: COMMON 2: DMX- 3: DMX+ NOTE: FOR DMX INPUT CABLE DMX CONTROLLER Black: V+ Operating Temp. Red: Red Light -20 C C Green: Green Light -4 F F White: Blue Light Line Voltage Input: LED Output: VAC VDC / 500W A C 100~240V I nput DMX INPUT DMX OUTPUT Male Input 1: COMMON 2: DMX- 3: DMX+ White: D+ Green: D- Black: GND Female Output NOTE: FOR DMX INPUT CABLE To Convert 3 Pin Mini XLR to 3 Pin DMX use converter cable Model#: LUM-B34XTS-XLR 1: COMMON 2: DMX- 3: DMX+ DMX CONTROLLER Black: V+ Operating Temp. Red: Red Light -20 C C Green: Green Light -4 F F White: Blue Light Line Voltage Input: LED Output: VAC VDC / 500W A C 100~240V I nput Up to 164ft. of V RGB LED STRIP

6 DMX System Wiring Match / Clear Code for WiFi, UX8, V8 Match Code: 2 Lumilum B34XTS App -RC LUM-B34XTS-DMX 120V STRIP 24V STRIP 1 Press key on panel for 3s, all the indicator light flicker. RF Wireless Syncing With V8 (-RC) With WiFi (-WF) With () Press any key on V8 within 5s if the indicator lights on panel stop flickering, match successfully. 2 Press any zone key on smart phone, then touch the color bar within 5s if the indicator lights on panel stop flickeringmatch successfully. (The smart phone has already matched with (-WF) -WF WiFi 2 * PS: No WiFi router needed when WiFi -WF is setup as network with phones directly. Press any key on panel B within 5s if the indicator lights on panel A stop flickering, match successfully. Clear Code: Match Code Sequence 1. Configure WiFi -WF with, which enables the smart phone to control the DMX device via WiFi -WF. Press keys simultaneously on for more than 6s, if all the indicator lights flicker 3 times, deactivate the matching successfully. 2 Configure V8 (-RC) which enables -RC to control DMX device.