Telexir PCRF. Quick Start Guide. Product version: Document version: 1.1

Transcription

1 Telexir PCRF Quick Start Guide Product version: Document version: 1.1 Telexir 2014

2 Revision History Date Version Author Revision Evgenia Martynyuk Document created Evgenia Martynyuk Minor corrections Telexir

3 Table of Contents Introduction... 4 Related Materials... 4 Abbreviations... 4 Policies Configuration Task Example... 5 Basic Task Description... 5 Network Architecture... 5 Information Flow... 6 Required Configuration... 6 Network Components Interaction... 6 Policies Configuration Steps DPI/P-GW Static Rules Configuration Result Telexir

4 Introduction Telexir PCRF Quick Start Guide Telexir PCRF is a standard compliant policy management solution that enables operator to dynamically control network elements with real-time policies based on service, subscriber or usage control. This step-by-step guide will help you to understand the essential principle of policy logic configuration of Telexir PCRF system. Related Materials 1. Installation Guide (Telexir PCRF Installation Guide.docx) 2. Administrator's Guide (Telexir PCRF Administrator's Guide.docx) 3. SPR Configuration Interface description (Telexir PCRF SPR Configuration Interface.docx) 4. Subscriber Management Interface description (Telexir PCRF Subscriber Management Interface.docx) 5. Policy Engine description (Telexir PCRF Policy Engine.docx) 6. Policy Library description (Telexir PCRF Policy Library.docx) 7. Standards: a) IETF RFC 3588 Diameter Base Protocol b) IETF RFC 4006 Diameter Credit Control Application c) 3GPP TS Policy and Charging Control over Gx Reference Point. Rel. 9 d) 3GPP TS Charging Rule Provisioning over Gx Interface. Rel. 9 Abbreviations Abbreviation AAA ACR BSS CRM DDF DPI O&M SPR Meaning Authentication Authorization Accounting Access Control Router Business Support System Customer Relationship Management Data Distribution Function Deep Packet Inspection Operations and Maintenance Subscriber Profile Repository Telexir

5 Basic Task Description Policies Configuration Task Example Telexir PCRF is able to work with many BSS tariffs, subscriber ID types (IMSI, MSISDN), different DPI/P-GW. Also can perform congestion management, traffic accumulation, and other operations. Telexir PCRF can be geographically distributed or be installed as a stand-alone cluster/node. This document covers only basic task of Telexir PCRF, where: PCRF clusters are installed only in two regions: Region_1 and Region_2. And the subscriber doesn t change the location (no moving from one region to another in this case). Only two BSS tariffs are used. Simple policy selection configuration is performed. Basic Task Description It is required to configure network core in such a way that the subscriber could have an access to network recourse according to the tariff which was chosen by the subscriber in the Self-Care portal. Available for the subscriber tariffs: Internet_unlim and Internet_512 Subscriber s ID (IMSI) is The subscriber is located in region Region_1. Network Architecture The following network architecture is used for the task: Figure 1. Example Network Architecture BSS (Self-Care Portal) HTTP smile.ddf1.com smile.ddf2.com DDF DDF HTTP HTTP Region_1 PCRF PCRF msk-pcrf1.scartel.dc msk-pcrf2.scartel.dc PCRF PCRF Region_2 Gx test.ugw01.g4lab.ru test.ugw02.g4lab.ru Gx RAN Traffic DPI/P-GW Internet DPI/ P-GW Telexir

6 Telexir PCRF Quick Start Guide In the figure above (Figure 1) we can see Telexir PCRF system that contains DDF cluster and two PCRF clusters in two regions. Two regions are taken to show that Telexir PCRF system can be geographically distributed. In case if only one PCRF cluster is required the DDF component is not need. All management command from BSS will be sent directly to PCRF cluster. All further actions will be performed with DDF and regional PCRF in Region_1. Information Flow When the subscriber chooses an Internet tariff the following information flow will be generated: Figure 2. Information Flow BSS tariff DDF service PCRF service/policy DPI/P-GW rule Subscriber 1. When the subscriber chooses a specified tariff the BSS sends management command to DDF to assign a specified service to the subscriber. 2. When the management command from BSS is received then DDF resend this command to regional PCRF, where the subscriber is attached to the network. 3. When the specified service is assigned to the subscriber, PCRF selects a policy according to the service information. When the policy is chosen then a corresponding rule is sent to DPI/P-GW. 4. DPI/P-GW gives access to the network resources according to a received rule. Important to understand: BSS operates with tariffs. DDF operates with services. PCRF operates with services and policies. DPI/P-GW operates with rules. Required Configuration To complete the task configuration of the following must be performed: Network components interaction Policies on PCRF Static Rules on DPI/P-GW Network Components Interaction It is needed to configure the network component interaction. The configuration is performed in O&M Console: Connectivity information of DDF with all PCRF clusters must be set in DDF O&M Console. Connectivity information of PCRF and DPI/P-GW must be set in PCRF O&M Console of regional PCRF cluster where this DPI/P-GW is used. Telexir

7 Required Configuration When PCRF and DPI/P-GW connectivity information is set then CER/CEA, DWR/DWA messages exchange is possible. DDF O&M Console Configuration DDF O&M is available at: Specify information about all system clusters and nodes by doing the following steps: 1. Open DDF O&M console in a browser tab and choose the primary DDF node in the Server List. 2. Choose Configuration -> Network Topology -> Clusters in the Operations block. Only DDF cluster information will be displayed. 3. Click Add button in appeared Clusters table and set required parameters for all PCRF clusters. Region_1 PCRF cluster information example: Parameter Description Cluster ID 2 Cluster Role 3 Cluster SSR Subscription 0 Cluster Name First Regional PCRF Description Cluster in Region 1 Important Make sure that ID of each cluster of the Telexir PCRF system in unique within the whole system configuration. 4. Go to Configuration -> Network Topology -> Peers. Click Add button in appeared Peers table and set required parameters for all PCRF nodes. Region_1 nodes information example: Primary Region_1 node Secondary Region_1 nodes Peer ID 21 Peer ID 22 Cluster ID 2 Cluster ID 2 Dialect 0 (Default) Dialect 0 (Default) Host msk-pcrf1.scartel.dc Host msk-pcrf2.scartel.dc Realm scartel.dc Realm scartel.dc Address msk-pcrf1.scartel.dc Address msk-pcrf2.scartel.dc Port 3868 Port 3868 Protocol 6 (TCP) Protocol 6 (TCP) Auto Connect 1 Auto Connect 0 Mandatory 1 Mandatory 1 Priority 0 Priority 1 Important Secondary node priority must be set lower than primary node priority for each PCRF cluster (0 is the highest priority). For example, set Priority=1 for secondary and Priority=0 for the primary node. Telexir

8 Telexir PCRF Quick Start Guide Figure 3. DDF O&M Console Peers Information Configuration Example 5. Go to Configuration -> Network Topology ->HTTP Peers. Click Add button in appeared HTTP Peers table and set required parameters for all PCRF nodes. Information example: Primary Region_1 node Secondary Region_1 nodes Cluster ID 2 Cluster ID 2 Peer ID 21 Peer ID 22 HTTP address msk-pcrf1.scartel.dc HTTP address msk-pcrf2.scartel.dc HTTP port 80 HTTP port 80 This table is used by DDF to send management HTTP requests to PCRF nodes. PCRF O&M Console Configuration PCRF O&M is available at: Specify information about all clusters and nodes this cluster interacts with via Diameter protocol by doing the following steps: 1. Open PCRF O&M console in a browser tab. 2. Choose Configuration -> Network Topology -> Clusters in the Operations block. Click Add button to add information about all PCEF clusters this cluster interact with. DPI/P-GW cluster information example: Parameter Description Cluster ID 7 Role PCEF Cluster SSR Subscription 0 (Cluster SSR NONE) Name Huawei UGW Description Huawei UGW Important Make sure that ID of each cluster of the Telexir PCRF system in unique within the whole system configuration. 3. Choose Configuration -> Network Topology -> Peers. Check if Peer IDs of this PCRF cluster nodes are the same as were set in DDF O&M Console Peers table. Click Add button to add information about all cluster nodes this cluster interact with via Diameter interface (PCEF clusters and DDF cluster). Telexir

9 Required Configuration DPI/P-GW nodes information example: Primary DPI/P-GW node Secondary DPI/P-GW node Peer ID 78 Peer ID 79 Cluster ID 7 Cluster ID 7 Dialect 0 (Default) Dialect 0 (Default) Host test.ugw01.g4lab.ru Host test.ugw02.g4lab.ru Realm g4lab.ru Realm g4lab.ru Address test.ugw01.g4lab.ru Address test.ugw02.g4lab.ru Port 3868 Port 3868 Protocol 6 (TCP) Protocol 6 (TCP) Priority 0 Priority 1 Mandatory 1 (Enabled) Mandatory 1 (Enabled) Enabled 1 (Enabled) Enabled 1 (Enabled) Important Secondary node priority must be set lower than primary node priority for each PCRF cluster (0 is the highest priority). For example, set Priority=1 for secondary and Priority=0 for the primary node. Figure 4. PCRF O&M Console DPI/P-GW Information Configuration Example 4. Go to Configuration -> Server Settings and set default_region parameter value for this PCRF cluster. For example, default_region=region_1. Telexir

10 Policies Configuration Steps Telexir PCRF Quick Start Guide When required information is set in the O&M console of DDF and PCRF clusters the policies configuration can be performed. Figure 5. Policies Configuration BSS (Self-Care Portal) HTTP 1 DDF DDF 2 smile.ddf1.com smile.ddf2.com HTTP Region_1 PCRF PCRF msk-pcrf1.scartel.dc msk-pcrf2.scartel.dc engine.lua Policies 3 rules.xml DPI Rules 4 Gx test.ugw01.g4lab.ru test.ugw02.g4lab.ru RAN Traffic DPI DPI/P-GWP-GW Internet 1. On DDF (or on PCRF if DDF is not used) provide services information to the Service Dictionary by SPR Configuration Interface method addserviceinfo. For Internet_unlim tariff the following information will be provided (Full_Access_Unlim service: Unlim&description=full access internet connection with unlimited speed For Internet_512 tariff the following information will be provided (Full_Access_512 service): 2&description=full access internet connection with 512kbps speed Telexir

11 Required Configuration Important The method addserviceinfo adds information only to the Service Dictionary. It doesn t assign a service to a subscriber and serves only for validation purposes of new BSS services. Information For more information about the SPR Configuration Interface, refer to "Telexir PCRF SPR Configuration Interface.docx". 2. On DDF (or on PCRF if DDF is not used) provide information about the subscriber profile, which the services will be applied to, by Subscriber Management Interface method addsubscriber. Request example: _subscriber When the subscriber profile is created now it is possible to assign BSS services to this subscriber. Important When subscriber chooses a tariff in the Self-Care Portal then the BSS automatically assigns an appropriate service to this subscriber by sending Subscriber Management Interface method addservice to DDF. Request example: =Full_Access_Unlim Information For more information about the Subscriber Management Interface, refer to "Telexir PCRF Subscriber Management Interface.docx". 3. On regional PCRF add policy selection algorithm for new services in engine.lua. In our case the following script will be created: --require("etc/pcrf/config/lua/pcrf_module") function GxSelectPolicy() if (is_service_active("full_access_unlim")) then set_policy("policy_full_access_unlim") log_write(string.format("policy: '%s' selected for %s", get_policy(0), get_subscriber_id())) return 0 end if (is_service_active("full_access_512")) then Telexir

12 Telexir PCRF Quick Start Guide set_policy("policy_full_access_512") log_write(string.format("policy: '%s' selected for %s", get_policy(0), get_subscriber_id())) return 0 end end Policy selection algorithm (engine.lua) is launched when the subscriber attaches to the network, or when updated information is provisioned from BSS. When engine.lua is launched subscriber services are analyzed (is_service_active() function) and based on the result policies are chosen (set_policy() function). Information For more information about policy selection algorithm configuration, refer to "Telexir PCRF Policy Engine.docx" 4. On regional PCRF configure mapping of PCRF policies and DPI/P-GW rules in rules.xml file. In our case the following description will be added: <?xml version="1.0" encoding="utf-8"?> <PolicyDef xmlns=" version="1"> <Policy Name="policy_full_access_unlim"> <Huawei> <Rules> <Charging-Rule-Base-Name Value="npUnlim_up"/> </Rules> </Huawei> </Policy> <Policy Name="policy_full_access_512"> <Huawei> <Rules> <Charging-Rule-Base-Name Value="np512_up"/> </Rules> </Huawei> </Policy> </PolicyDef> An appropriate rule will be applied on subscriber session on DPI/P-GW when a PCRF policy is chosen for the subscriber. Rules describe specified AVPs (bearer configuration, QCI, bandwidth) that will be sent to DPI/P-GW. Information For more information about static DPI/P-GW rules configuration on PCRF, refer to "Telexir PCRF Policy Libpary.docx". DPI/P-GW Static Rules Configuration Static rules configuration on DPI/P-GW must be performed by the network specialist according to desired traffic management. In our case, it is required to have two static rules. For example: Telexir

13 Result npunlim_up. Static rule that shapes traffic according to Internet_unlim tariff in BSS np512_up. Static rule that shapes traffic according to Internet_512 tariff in BSS Result When all required configuration is performed the tariffs become available for the subscriber. Let s see the following example scenario: 1. Subscriber chooses Internet_unlim tariff before starting his Internet session. 2. Subscriber starts the Internet session. 3. Subscriber chooses Internet_512 tariff in real time. Figure 6. Example Scenario UE DPI/P-GW PCRF BSS addservice=full_ Access_Unlim 1 Attach Gx CCR-I Subscriber-id: Framed-IP-Address: Policy Selection Policy: policy_full_access_unlim 2 Gx CCA-I 3 Charging-Rule-Install: Charging-Rule-Name: "npunlim_up" addservice=full_ Access_ Policy Selection Policy: policy_full_access_512 Gx RAR 6 Modify bearer Charging-Rule-Remove: Charging-Rule-Name: "npunlim_up" Charging-Rule-Install: Charging-Rule-Name: "np512_up" Telexir

14 Telexir PCRF Quick Start Guide 1. When subscriber chooses Internet_unlim tariff before starting his Internet session the following command is sent to DDF ull_access_unlim 2. After subscriber device attach the following policy is chosen by PCRF: policy_full_access_unlim 3. the following rule is sent to DPI/P-GW in AVP Charging-Rule-Install: npunlim_up The following information is displayed in the log in CCA-I message: Figure 7. Log Message Example (CCA-I) Information To see log messages in real time execute command in the command line: lv 4. When subscriber chooses Internet_512 tariff in real time the following command is sent to DDF ull_access_ the following policy is chosen by PCRF: policy_full_access_ the following rule is sent to DPI/P-GW in AVP Charging-Rule-Install: np512_up The following information will be displayed in the log in the RAR message: Telexir

15 Result Figure 8. Log Message Example (RAR) Information It also possible to see Diameter traces, which are available at: Figure 9. Traces Example Telexir

16 Figure 10. Trace Message Example Telexir PCRF Quick Start Guide Telexir