A3 GMDSS CONSOLE DEALERS MANUAL

Transcription

1 FURUNO USA A3 GMDSS CONSOLE DEALERS MANUAL MODEL: RC18xx Series These Instructions are intended for Furuno authorized Agents and Dealers ONLY! These Instructions should not be released to the operator or owner of the equipment.

2 FURUNO USA OSE-GMD-30Z

3 TABLE OF CONTENTS This manual contains procedures for changing system settings in the GMDSS console. This information is intended for Dealer use only and should not be left with the console. 1. DP DSC Felcom FM FS-1570/FS IB i

4 1.1 DP-6 NBDP Terminal General These materials are provided to allow an authorized Furuno dealer to change the ID and Answerback Codes ID Codes 1) Press the [F5] key to enter the Station menu. 2) Press the key to select the ID to be entered: 6: Group ID Entry (4/5 digit) 7: Group ID Entry (9 digit) 8: Select ID Entry (4/5 digit) 9: Select ID Entry (9 digit) 3) Press the [Enter] key. 4) Press the [Caps Lock] key. 5) Key in ID (space) CODE. 6) Enter the new ID and press the [Enter] key to save Answerback Code 1) Press the [F5] key to enter the Station menu. 2) Press the [5] key to select Answerback Code Entry. 3) Press the [Enter] key. 4) Press the [Caps Lock] key. 5) Key in ANSWER (space) CODE. 6) Enter the new ID and press the [Enter] key to save. 1

5 2.1 DSC-60 DSC/Watch Receiver General These materials are provided to allow an authorized Furuno dealer to change the System Settings and MMSI System Settings 1) Press the [#/SETUP] key, to enter the Setup menu. 2) Select System and press the [ENT] key. 3) Enter the password, , to turn off the protection. 4) Using the arrow and [ENT] keys, change the settings to match the following: WATCH RCVR: MF/HF LINE OUT LEVEL: +0dBm TX-KEY TIMING: AUTO RT PORT: MIF REMOTE STATION: OFF NBDP PORT: ON LANGUAGE: ENGLISH 5) When completed press the [CANCEL] key twice, to exit MMSI 1) Disconnect the power and the printer cable from the right printer on the GMDSS console. Remove the printer brackets and the printer from GMDSS Console. 2) Disconnect the cables from the rear of the DSC-60. Making note of their locations. 3) Remove the 4 screws holding the DSC-60 bracket in the console. 4) Remove the side screws and washers holding the bracket in place. 5) Remove the top cover by removing the 4 side screws, and 1 screw from the rear panel of the DSC-60. 6) Connect power to the DSC-60. 7) Turn on the unit and wait for the WATCH KEEPING screen to appear. 2

6 2.1 DSC-60 DSC/Watch Receiver (Continued) MMSI (Continued) 8) Press the NMI switch located on the front right of the Control/Modem PCB. 9) The unit will now display: EEROM clear NO CLEAR MMSI CLEAR ALL CLEAR 10) Enter the password, As you enter the password, the unit will emit error tones. Ignore the error tones as you enter the password. 11) Use the down arrow key to select MMSI Clear. Press the [ENT] key. 12) Enter the 9 digit MMSI number and press the [ENT] key. 13) The display will now show PLEASE POWER OFF. Turn off the DSC-60 power. 14) Turn the DSC-60 power back on. 15) Now verify the MMSI change. 16) Press the [SETUP] key. Use the arrow keys to select SYSTEM. Press the [ENT] key. 17) The first line of the System screen should be the MMSI you just entered. 18) Reassemble the DSC-60 and the associated equipment. 3

7 3.1 Felcom General These materials are provided to allow an authorized Furuno dealer to change the IMN IMN 1) Press the [F8] key, to enter the Setup menu. 2) Press the [2] key to select the System Setup. 3) Select IMN. 4) While pressing the [ALT] key, type in [I], [M], [N]. 5) Now enter the IMN and press the [Enter] key. 6) Press the [Esc] key, then press the [Enter] key External Equipment (Refer to Pg. 20 of the Installation Manual, Felcom 15) This procedure will allow adding a DMC or additional remote boxes. 1) Press the [F8] key, then the [2] key, to show the System Setup menu. 2) Using the down arrow key, select Command Window and press the [Enter] key. 3) At the Enter Job No.: prompt, enter FURUNOSERVICE, and press the [Enter] key. 4) At the PASSWORD: prompt, enter FELCOM15, and press the [Enter] key. 5) To show the Remote Box Setup menu, press the [1] key, then the [Enter] key. 6) Press the number key for the equipment that is not connected. In a standard installation, you would change numbers 4 and 5. If the system includes a DMC, you would also change number 1. 7) Select [1] for ON or [2] for OFF and press the [Enter] key. 8) When completed, press the [E] key to Exit. Then press the [Esc] key until you return to the system status screen. 4

8 4.1 FM General These materials are provided to allow an authorized Furuno Agent or Dealer to change the MMSI and System Settings MMSI Settings 1) Before powering the unit on, install the Protection Key (RC ) or a jumper between Pins 2 and 15 of the [PRINTER] port. 2) Turn on the unit and press the [MENU] key, this will open the SYSTEM MENU. Using the [ ], down arrow key, select SYSTEM and press the [ENT] key. ****SYSTEM MENU**** ALARM AUTO ACK ERASE LOG MEMORY CHANNEL MESSAGE FILE ENTRY ****SYSTEM MENU**** POSITION PRINT OUT VOLUME SYSTEM 3) Enter the password, , then press the [ENT] key. *SYSTEM SETUP MENU* SELF ID GROUP ID LIST INTERCOM NAMING PROGRAM VERSION 4) Select SELF ID and press the [ENT] key. ID ENTRY and ID CLEAR will appear as a pop-up menu. 5) If this is a new install, select ID ENTRY, using the arrow keys. Then press the [ENT] key. Now enter the ship s MMSI and press the [ENT] key. If the MMSI needs to be changed, select ID CLEAR, then press the [ENT] key. Now return to step 4, to reenter the MMSI. 6) Press [CANCEL], once to continue programming, twice to exit the SETUP MENU. 5

9 4.1 FM-8800 (Continued) General System Settings This section includes protected operational settings. For other settings refer to the Operators Manual, FM-8800 (Chapter 4-Basic Setup) *SYSTEM SETUP MENU* SELF ID GROUP ID LIST INTERCOM NAMING PROGRAM VERSION *SYSTEM SETUP MENU* AUTO 1W ON AUTO REVERT ON ATIS ID CH70 BOARD CH CONFIG CH MODE 1) From the SYSTEM SETUP MENU, use the [ ], down arrow key to select AUTO 1W. If this setting is OFF, press [ENT], select ON and press [ENT]. 2) Select AUTO REVERT. This setting determines if the VHF will revert to CH16 when the handset is returned to the cradle. The default is ON and it is changed in the same manner as AUTO 1W. 3) Select CH MODE and press the [ENT] key. The followoing table will display: INTL = ON USA/WX = OFF CANADA = OFF INLD = OFF PRIV = OFF This setting determines the availability of operational modes. The default is INTL (International) mode ON. Highlight each mode and press [ENT] to change the setting. When all required modes have been turned ON, press [CANCEL] once. This will return to the SYSTEM SETUP MENU. The FM-8800 mounted in the console will have INTL and USA/WX set to ON. 6

10 4.1 FM-8800 (Continued) General System Settings (Continued) This section includes protected operational settings. For other settings refer to the Operators Manual, FM-8800 (Chapter 4-Basic Setup) *SYSTEM SETUP MENU* SELF ID GROUP ID LIST INTERCOM NAMING PROGRAM VERSION *SYSTEM SETUP MENU* AUTO 1W ON AUTO REVERT ON ATIS ID CH70 BOARD CH CONFIG CH MODE *SYSTEM SETUP MENU* SCAN/DW SP MUTE ON TIMEOUT TIMER ON TX POWER TONE TEST 4) From the SYSTEM SETUP MENU, use the [ ], down arrow key to select TIMEOUT TIMER. If this setting is OFF, press [ENT], select ON and press [ENT]. 5) Press [CANCEL] twice to return to the main screen. The unit should now be operational. 7

11 5.1 FS-1570/FS MMSI This procedure will allow changing the MMSI, Group ID and Model. This should performed by an authorized Furuno dealer only. 1) Open the Transceiver and remove the cover from the T-CPU. (Refer to diagram on the inside cover of the Transceiver) 2) Power on the unit. Press the NMI Switch. EEROM clear NO CLEAR MMSI CLEAR ALL CLEAR 3) Enter the password, ) Select MMSI CLEAR and press the [ENT] key. 5) Enter the ship s MMSI and press the [ENT] key Model 1) Open the Transceiver and remove the cover from the T-CPU. (Refer to diagram on the inside cover of the Transceiver) 2) Power on the unit. Press the NMI Switch. EEROM clear NO CLEAR MMSI CLEAR ALL CLEAR 3) Enter the password, ) Select ALL CLEAR and press the [ENT] key. 5) Select the correct model and press the [ENT] key. 6) Enter the ship s MMSI and press the [ENT] key. 8

12 5.1 FS-1570/FS-2570 (Continued) Model (Continued) EEROM clear NO CLEAR MMSI CLEAR ALL CLEAR 7) Turn the system off and back on. 9

13 6.1 IB-583 NBDP Terminal General These materials are provided to allow an authorized Furuno dealer to change the ID and Answerback Codes ID Codes 1) Press the [F5] key to enter the Station menu. 2) Press the key to select the ID to be entered: 6: Group ID Entry (4/5 digit) 7: Group ID Entry (9 digit) 8: Select ID Entry (4/5 digit) 9: Select ID Entry (9 digit) 3) Press the [Enter] key. 4) Press the [Caps Lock] key. 5) Key in ID (space) CODE. 6) Enter the new ID and press the [Enter] key to save Answerback Code 1) Press the [F5] key to enter the Station menu. 2) Press the [5] key to select Answerback Code Entry. 3) Press the [Enter] key. 4) Press the [Caps Lock] key. 5) Key in ANSWER (space) CODE. 6) Enter the new ID and press the [Enter] key to save. 10