Information ... Technical And Operational Description ... Connections ... Card Data Format ... Demo Software ... Specifications ...

Transcription

1 TM951035

2 Information... 1 Technical And Operational Description... 3 Connections... 7 Card Data Format Demo Software Specifications Communication Protocol FCC COMPLIANCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communication. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

3 BCR300 Series Barcode Reader MACHINE TYPE FUNCTION BC CODE39 I - 2/5 2/5 EAN13 EAN8 UPCE UPCA CODE128 CODABAR AUTO TEST GNET VER 1.2 BCR300B Red LED BATTERY 006P RTC LOW BAT BEEP F- MEM 512 KB RS REC QUEUE BC CODE39 I - 2/5 2/5 EAN13 EAN8 UPCE UPCA CODE128 CODABAR AUTO TEST GNET VER 1.2 BCR300F Infrared BATTERY 006P RTC LOW BAT BEEP F- MEM 512 KB RS REC QUEUE - 1 -

4 Information Standard Package Main unit ( BCR300X ) Software Disk Including User s Manual ( DISK5148 ) Cable ( WAS-1518 ) Battery 9V ( BAT-1016 ) Optional Power Adaptor DC12V/120VAC ( APR-1014 ) or DC12V/230VAC ( APR-1015A ) - 2 -

5 Front Panel Display and Operations CARD READER READY INDICATOR PHONE JACK ERROR INDICATOR BATTERY BOX POWER SWITCH CARD READER Swipe the card through the entire length of the slot to read. ERROR INDICATOR ( Red color ) When encountering erroneous input, defective card, misread, or incorrectly encoded data, the device will turn on the ERROR indicator. READY INDICATOR ( Green color ) Indicating the reader is ready to accept new inputs. PHONE JACK For connection to host computer and external Power. BATTERY BOX Put the battery in box and hold battery. POWER SWITCH Turn the BCR300 on/off power

6 Technical And Operational Description Display Information STATUS POWER ON GREEN LED BLINK 2 TIMES RED LED BLINK 2 TIMES BUZZER BEEP-BEEP READ CARD X READY ON OFF X O READ OK BLINK 1 TIMES OFF BEEP X READ ERROR OFF BLINK 1 TIMES BEEP-BEEP-BEEP X LOW BATTERY ON BLINK... BOM-... X MEMORY FULL BLINK OFF... BOM-... X MEMORY BAD OFF ON..BOM-BOM- BOM.. X Replace Battery 1. POWER TURN OFF 2. TAKE NEW BATTERY 3. TAKE THE COVER AWAY AND CONNECT THE BATTERY TO THE SOCKET 4. SNAP THE COVER IN THE POSITION - 4 -

7 Technical And Operational Description Barcode Card Standard Card A D B C B Item Parameter Minimal Typical Maximal A B C D Bar Width Quiet Zone Resolution Scan Position Unit mm mm mm mm Test Card Lable Size Unit: mm - 5 -

8 Technical And Operational Description Supporting Barcode Barcode Name Maximal Length Data Character Character Amount Check Code CODE ~ 9 A ~ Z + - * / % $. space 44 - EAN ~ 9 10 o EAN ~ 9 10 o UPC-A 12 0 ~ 9 10 o UPC-E 6 0 ~ 9 10 o INTERLEAVED 2 of ~ CODABAR 32 0 ~ 9 A B C D + - * / $. : 16 x CODE ASCII = 00 ~ 127 Code A/B/C Shift/FNC 1/2/3/4 128 o Note: 1. Maximal Length : CODE 39 include start/end code. CODE 128 include start/end code. CODABAR include start/end code : Need or No need o : Need x : No need - 6 -

9 WAS-1518 DSB 9P FEMALE PIN * COLOR BLACK RED GREEN YELLOW FUNCTION RXD TXD POWER GND RJ-11 4P4C PIN * DSB 9P FEMALE Pin 1,4,6 connect togeter Connect to PC External Power RS-232 PORT PC Battery Power NETWORK Battery Power DS100R PC NOTE : IF you like to have TCP/IP function of BCR300, you have to work with DS100R to get it

10 A. Card Data String For BCR300 with Date&Time Barcode ID TAB Date SP Time SP Week Day EXAMPLE: * * 2002/07/22 11:11:35 2 Barcode ID : Data read from the card Date : Year/Month/Day Time : Hour/Minute/Second Week Day : 1 = Sunday 2 = Monday 3 = Tuesday 4 = Wednesday 5 = Thursday 6 = Friday 7 = Saturday SP : Space Separator B. Card Data String For BCR300 without date&time EXAMPLE : - 8 -

11 START IDBANK SOFTWARE Step1 : RUN IDBANK * BAUDRATE : 9600 BPS CHOOSE COM PORT PRESS MACHINE TYPE #2 CHOOSE TCP/IP #1 PRESS IP ADDRESS Step2 : Choose Com Port or TCP/IP and Machine Type NOTE : Press IP address before Choose Com Port - 9 -

12 Demo Software #1 PRESS SetTime #2 PRESS GetTime #3 PRESS GetVersion Step3 : Set BCR300 Date&Time and Get BCR300 Date&Time and Version Note: The Date&time come from PC Clock when run SetTime function. UPLOAD DATA PRESS STOP UPLOAD or UPLOAD Step4 : UPLOAD DATA CURRENT FILENAME #2 PRESS SAVE #1 PRESS SAVE

13 Demo Software Save to file data status Step5 : SAVE DATA TO A FILE PRESS EXIT Step6 : AUTO ERASE & EXIT IDBanK NOTE : If you are running Upload in IDBank and the meanwhile, you are swiping the card on BCR300, it might interrupt the Upload

14 Demo Software STEP 7 : ENABLE PASSWORD FUNCTION NOTE : IF YOU RESTART MSR500, YOU HAVE TO ENTER PASSWORD THEN. Setting password Function Enable STEP 8 : CHANGE PASSWORD AND SET UP PASSWORD HINT. Change Password Default is blank Enter password hint for reminding of password Within 10 digits Reenter new password for confirmation Enter any character for reminding of password Enter correct password according to the showed hint, and it will enter MSR500 program

15 BC Barcode Card ( for LED ) : Code 39, I25, EAN13, EAN8, UPCE, UPCA, CODE 128, CODABAR, CODE 93, CODE 11 BC Barcode Card ( for Infrared ): Code 39, I25, EAN13, EAN8, UPCE, UPCA, CODE 128, CODABAR RS-232 GNET VER 1.2 F- MEM 512 KB BATTERY 006P AC DC RS232 Interface : RS232, Half-Duplex, 8N1, 9600 bps Communication Protocol : GIGA-TMS Net Version 1.2 (GNET V1.2) Memory Size for Storing Data : Serial Electrically Erasable PROMs ( EEPROM ) 32K bytes Battery Power : 6F22DN 9V / 006P and Low Battery Detect Power Supply : DC 8V ~ 12V, 300mA Dimensions : D 40 x W 57 x H 97 mm % C/F Environment : Operating Temp : 0 ~ 55 Deg.C Storage Temp : -10 ~ 55 Deg.C Humidity : 10 ~ 90 % relative Mounting : Portable or Any surface

16 GNET FEATURES Support TTY (TELE TYPE) OPERATION - Use TTY to send commands and messages. Simple handshaking - One enquiry one answer back. Multi-link capability Expandability - GNET provides 4 major functions: 1. POLLING 2. LOGIN / LOGOUT 3. DATABASE 4. INFORMATION Also can be expandable. Simple format GNET V1.2 Use ASCII value for each field and use Separator "," between two Fields. GNET Handshaking ACK NACK NACK TIME OUT TX1 RX TX2 RX TX3 RX TX3 RX TX4 TIME OUT RX1 ACK RX2 NACK RX ERR NACK RX3 ACK NO RX4 WAIT RX GNET PACKET STX CMD CONTENTS CHKSUM CR STX REPLY CONTENTS CHKSUM CR ITEM Dec Hex Control Key Function STX CMD CONTENTS CHKSUM CR 2 02 ^B Start of Text Ascii Ascii Ascii Command Code Ascii Ascii Ascii Contents Data Ascii Ascii Ascii Check Sum 13 0d ^M Carriage Return REPLY (78) 65 (4e) 41 (N) A (Negative) Acknowledge

17 Communication Protocol Command Index Table Topic SETTING DATABASE Command F S T N G E Contents - Date,Time,Week - - Number - Description Get Product Version Set Date,Time and Week Get Date and Time Get Number of Record Read Record by Number Erase All Record Reply Index Table Topic ACK NAK Reply A N Contents Reply Information See Error Index Table Description ACK+Information NAK+Information Error Index Table ( For Reply NAK ) Topic ACCESS LEVEL COMMAND CODE DATABASE FILE Error Index Description Access Denied or Password Error Command packet is too long Command packet is empty Command code is out of range Illegal Command or Data Database and Register is Empty 06 Record number is out of range Check Sum Error Memory Not Enough 0A File Not Exist

18 Communication Protocol 1. GET NUMBER OF RECORD : STX N CR STX A NUMBER CHKSUM CR NUMBER Record Count. 4 Bytes Width ( 0000h ~ 2000h ) EXAMPLE 02 N 0d 02 A 000C 14 0d The Total of Record Count : READ RECORD BY NUMBER : STX G NUMBER CR STX A NUMBER, DATA CHKSUM CR NUMBER Record Count, 4 Bytes Width ( 0000h ~ 1FFFh ), Total: 8192 DATA Record Data ( BARCODE ID, SYMBOLOGY, DATE&TIME&WEEK ) SYMBOLOGY A B C D E F G H I FUNCTION CODE39 I25 25 CODABAR CODE128 EAN8 EAN13 UPC-A/EAN13 UPC-E Week SUN MON TUE WED THU FRI SAT EXAMPLE 02 G d 02 A 0002, FF C FF 2002/07/29 16:41: d Read Record Number : 2 Barcode ID : , Symbology : I25, Date:2002/7/29, Time:16:41:01, Monday

19 Communication Protocol 3. SET DATE AND TIME : STX S YYYYMMDDhhmmssw CR STX A CR YYYY MM DD hh mm ss Year ( xx ) Month (01-12 ) Date ( ) Hour ( ) Mintue ( ) Second ( ) W Week ( 1-7 ) Week SUN MON TUE WED THU FRI SAT EXAMPLE 02 S d 02 A 0d Set Date = 2002 / 7 / 22 Set Time = 15 : 54 : 30, Wednesday 4. GET DATE AND TIME: STX T CR STX A YYYYMMDDhhmmssw CR EXAMPLE 02 T 0d 02 A d Get Date : 2002 / 7 / 22 Get Time : 15 : 55 : 06, Wednesday 5. GET PRODUCT VERSION : STX F CR STX A VERSION CR VERSION xxrmm, xx : Firmware Version x.x, Rmm : Modify mm Times

20 Communication Protocol EXAMPLE 02 F 0d 02 A 1.0R00 0d Firmware Version = 1.0 Modify times = ERASE ALL RECORD : STX E CR STX A CR EXAMPLE 02 E 0d 02 A 0d ERASE ALL RECORD