Pressure control valves type B
|
|
- Paula Hudson
- 5 years ago
- Views:
Transcription
1 Pressure control valves type B Burner Components Catalogue 1 Contents Application... page 2 Design... page 2 Exploded view... page 2 Function... page 2 Technical data... page 3 p-q table... page 3 Dimension... page 3 Port positions... page 4 Installation... page 4 Code numbers... page 4 Accessories and spare parts... page 4 Gasket set and springs... page 5 520F0286 DKBD.PK.033.A1.02
2 Application B-valves are designed for installation in oil plant to control the system pressure. They can be used with hydraulic oil, lubricating oil and fuel oil with lubricant properties. Design The valve consists of a cast iron body with built-in piston control. The pressure can be set using a screwdriver or a hexagon socket key in the setting screw (located inside the valve behind plug E). The valve pressure range can be altered by changing the spring. For each valve type there are five pressure ranges; see Technical data. Exploded view B: Pressure control valve set Function The valve operates in the same way as a pressure relief valve. Oil is led to the supply side P and the spring/piston ensures constant pressure by leading the oil through the hole in the piston to the return side R. Since the valves are quantity and viscosity-dependent, the correct pressure can only be set when the working temperature has been reached. See table for pressure change p Q. E: Pressure control (under plug) R: Return to tank P: Pressure port P n : Pressure gauge port 2 520F0286 DKBD.PK.033.A1.02
3 Technical data Type B-PP-E B-P-E B-G-E B-GH-E B-GHG-E Viscosity range mm 2 /s ( cst.) 1.3 to 700 Capacity l/h See code number Pressure range bar See table Factory setting bar Min. pressure Pressure change across valve bar See p-q table Filter size/mesh size cm 2 /mm No integral filter Max. oil temperature C 180 Weight kg Ambient temperature C -10 to +90 Storage temperature C -20 to +60 p-q table Pressure change p as a function of quantity Q across valve. Qty Q p measured at p measured at p measured at in % of Q max 5 cst. 20 cst. 40 cst. 15 < 0.2 bar < 0.3 bar < 0.4 bar 50 < 0.4 bar < 0.6 bar < 0.8 bar 100 < 1.2 bar < 2.2 bar < 3.0 bar As can be seen from the table, if the springs for pressure ranges 0, 1 and 2 (see list of code nos.) are used, the pressure change across the valve can be greater than the stated P min. If this is the case, a larger valve should be used, or two valves can be connected in parallel in order to reduce the quantity flowing through each valve. Over 40 cst. the values are higher and not stated because the uncertainty factor becomes too great. Dimension B-valve a1 b1 c1 d1 d2 f1 Max. tube NW f2 h (mm) dim. adjustment at pressure range PP G 1 / G 1 / P G 3 / G 1 / G G 3 / G 1 / G G 1 / G 1 / GH G 3 / G 1 / GHG G G 1 / F0286 DKBD.PK.033.A1.02 3
4 Port positions E: Pressure control (under plug) R: Return to tank P: Pressure port P n : Pressure gauge port Installation All connections must be airtight. Never use hemp or similar to seal threads. The system pressure can be measured in port P n, see port positions above. Only when the working temperature is reached can a correct measurement be taken. Code numbers SAFAG Designation Danfoss Min./nominal/max. Connection Pressure range no. No. capacity l/h thread bar B-PP-E-0 070H / 60 / 120 G 1 /4 0.5 to B-PP-E-1 070H / 60 / 120 G 1 /4 1 to B-PP-E-2 070H / 60 / 120 G 1 /4 2 to B-PP-E-3 070H / 60 / 120 G 1 /4 6 to B-PP-E-4 070H / 60 / 120 G 1 /4 15 to B-P-E-0 070H / 160 / 300 G 3 /8 0.5 to B-P-E-1 070H / 160 / 300 G 3 /8 1 to B-P-E-2 070H / 160 / 300 G 3 /8 2 to B-P-E-3 070H / 160 / 300 G 3 /8 6 to B-P-E-4 070H / 160 / 300 G 3 /8 15 to B-G-E-0 070H / 300 / 600 G 3 /8 0.5 to B-G-E-1 070H / 300 / 600 G 3 /8 1 to B-G-E-2 070H / 300 / 600 G 3 /8 2 to B-G-E-3 070H / 300 / 600 G 3 /8 6 to B-G-E-4 070H / 300 / 600 G 3 /8 15 to B-G-E-0 070H / 300 / 600 G 1 /2 0.5 to B-G-E-1 070H / 300 / 600 G 1 /2 1 to B-G-E-2 070H / 300 / 600 G 1 /2 2 to B-G-E-3 070H / 300 / 600 G 1 /2 6 to B-G-E-4 070H / 300 / 600 G 1 /2 15 to B-GH-E-0 070H / 1000 / 2000 G 3 /4 0.5 to B-GH-E-1 070H / 1000 / 2000 G 3 /4 1 to B-GH-E-2 070H / 1000 / 2000 G 3 /4 2 to B-GH-E-3 070H / 1000 / 2000 G 3 /4 6 to B-GH-E-4 070H / 1000 / 2000 G 3 /4 15 to B-GHG-E-0 070H / 3000 / 6000 G to B-GHG-E-1 070H / 3000 / 6000 G 1 1 to B-GHG-E-2 070H / 3000 / 6000 G 1 2 to B-GHG-E-3 070H / 3000 / 6000 G 1 6 to B-GHG-E-4 070H / 3000 / 6000 G 1 15 to 40 Accessories and spare parts The pressure control unit B (see Exploded view page 3) cannot be ordered as a spare part, i.e. only the body is required to make up a complete valve F0286 DKBD.PK.033.A1.02
5 Gasket set and springs Since the gasket set is also used for pumps, there will be gaskets in the set that are not intended for use with the valves. The springs are the same for valves as for pumps, although extra springs are included for the small PP valves. Designation Danfoss no. Gasket set Pressure range Springs Code number bar Code number B-PP-E-0 070H H to H0052 B-PP-E-1 070H H to 4 070H0053 B-PP-E-2 070H H to 9 070H0054 B-PP-E-3 070H H to H0055 B-PP-E-4 070H H to H0056 B-P-E-0 070H H to H0019 B-P-E-1 070H H to 4 070H0000 B-P-E-2 070H H to 9 070H0001 B-P-E-3 070H H to H0020 B-P-E-4 070H H to H0021 B-G-E-0 070H H to H0019 B-G-E-1 070H H to 4 070H0000 B-G-E-2 070H H to 9 070H0001 B-G-E-3 070H H to H0020 B-G-E-4 070H H to H0021 B-G-E-0 070H H to H0019 B-G-E-1 070H H to 4 070H0000 B-G-E-2 070H H to 9 070H0001 B-G-E-3 070H H to H0020 B-G-E-4 070H H to H0021 B-GH-E-0 070H H to H0022 B-GH-E-1 070H H to 4 070H0023 B-GH-E-2 070H H to 9 070H0024 B-GH-E-3 070H H to H0025 B-GH-E-4 070H H to H0026 B-GHG-E-0 070H H to H0027 B-GHG-E-1 070H H to 4 070H0028 B-GHG-E-2 070H H to 9 070H0029 B-GHG-E-3 070H H to H0030 B-GHG-E-4 070H H to H F0286 DKBD.PK.033.A1.02 5
6 6 520F0286 DKBD.PK.033.A1.02
7 520F0286 DKBD.PK.033.A1.02 7
8 Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved F0286 DKBD.PK.033.A1.02 Produced by Danfoss G1 advertising agency FO-Bi.SIL
Contents. Directional Control Valve 2 Series EPCV 452. Page 3. General Information. Page 4-5. Technical data. Page 6. Performance Curves.
Contents Page 3 Page 4-5 Page 6 Page 7 Page 8 Page 9 Page 10 General Information Technical data Performance Curves Dimensions : Hydraulic Valve and Accumulator Hydraulic Schematics Dimensions : Electrical
More informationDN100 (4") - DN500 (20") Hot Tappings
DN00 (4") - DN500 (20") Hot Tappings TONISCO B40 Hot Tapping Machine is versatile and easy to operate. It has a full range capability of setting valves DN00 DN500 by completing it with proper adapters.
More informationSonoSelect 10 and SonoSafe 10 energy meters
SonoSelect 10 and SonoSafe 10 energy meters Description The Danfoss SonoSelect 10 and SonoSafe 10 are ultrasonic compact energy meters intended for measuring energy consumption in heating applications
More informationSonoSelect and SonoSafe energy meters
SonoSelect and SonoSafe energy meters Description The Danfoss SonoSelect and SonoSafe are ultrasonic compact energy meters intended for measuring energy consumption in heating applications for billing
More informationRD 100. Spare parts list. RD 100 s/n BES Construction Tools PC AB No
RD 100 Spare parts list RD 100 s/n BES100496 2018 Construction Tools PC AB No. 9800153901 2018-10 General information This spare parts list applies to the following: Part number 8311030410 RD 100 Description
More informationPIONJÄR. Spare parts list. Petrol drills and breakers 120, 120 AV, 121 A, 130, 130 AV, 131 A
PIONJÄR 0, 0 AV, A, 0, 0 AV, A Spare parts list Petrol drills and breakers 0 Atlas Copco Construction Tools AB 00 00 0b 00 PIONJÄR 0, 0 AV, A, 0, 0 AV, A Contents Contents General Information................................................................
More informationSUCTION FILTERS. PRESSURE (ISO :2002) Collapse, differential for the fi lter element (ISO 2941): 1 MPa (10 bar)
COMPONENTS SUCTION ILTERS SD MATERIALS Cover & housing: Anodized aluminium alloy or 6&6 only: Cover: anodized aluminium alloy Housing: steel ypass valve: Polyammide Seals: NR Nitrile (KM on request fl
More informationWARNING ELECTRICAL SHOCK HAZARD
Description Safety Instructions The top-entry sub D9 connector kit is designed for enclosure sizes D1h D8h, E1 E2, and E1h E4h with VLT PROFIBUS DP MCA 101 option. It fits the following drives: VLT HVAC
More informationLH 700. Spare parts list. Forward and reversible plate. Valid from serial number. LH 700 Hatz Electric start 810 mm Bio
LH 00 Spare parts list Forward and reversible plate LH 00 Hatz Electric start 0 mm LH 00 Hatz Electric start 0 mm Bio LH 00 Hatz Electric start 0 mm LH 00 Hatz Electric start 0 mm Bio Valid from serial
More informationRH 658 L, 658 LS, 658 L-01
RH 658 L, 658 LS, 658 L0 Spare parts list Rock drills 00 Atlas Copco Construction Tools AB No. 9800 08 0 000609 RH 658 L, 658 LS, 658 L0 Contents Contents General information................................................................
More informationGrease Guns PRELIxx and PRELIxx PRO
Grease Guns PRELIxx and PRELIxx PRO 2014.1 Quality that leads Different grease gun colors for different grease types 03 Grease Guns PRELIxx and PRELIxx Pro 2014.1 Contents Contents PRELIxx 2014.1 Technical
More informationCOBRA. Spare parts list. Petrol drills and breakers COMBI Atlas Copco Construction Tools AB No c
COBRA COMBI Spare parts list Petrol drills and breakers 0 Atlas Copco Construction Tools AB 00 0 0c 00 COBRA COMBI Contents Contents General information................................................................
More informationSB 302. Spare parts list. Hydraulic breakers. Valid from serial number Atlas Copco Construction Tools AB No f
SB 0 Spare parts list Hydraulic breakers SB 0 Valid from serial number BES 0 Atlas Copco Construction Tools AB No. 900 0 0f 0 SB 0 Contents Contents General information................................................................
More informationLH 700. Spare parts list. Forward and reversible plate. Valid from serial number. LH 700 Hatz Electric start 810 mm Bio
Forward and reversible plate Hatz Electric start 0 mm Hatz Electric start 0 mm Bio Hatz Electric start mm Bio Valid from serial number 0000 0000 0000 Contents Contents General information.....................................................................................................................................
More informationMechanically Activated Device for Dry Run Protection in Applications with LORENTZ Solar Pump Systems
Well Probe Mechanically Activated Device for Dry Run Protection in Applications with LORENTZ Solar Pump Systems The switch can be used to detect the water level within a well. When the water level in the
More informationSECTION 8 - ULTRA & ULTRA-C PARTS CATALOGUE
SECTION 8 - ULTRA & ULTRA-C PARTS CATALOGUE PART # DESCRIPTION PAGE MOUNTING KITS & TANKS 903U MOUNTING KIT WITH TANK 801-802 905U MOUNTING KIT WITHOUT TANK 803-804 902U MOUNTING KIT - CRADLE, BLOCKS &
More informationDN40 (1 1/2") - DN200 (8") Hot Tappings
DN40 ( /2") - DN200 (8") Hot Tappings TONISCO B30 Hot Tapping Machine is versatile and easy to operate. It has a full range capability of setting valves DN40 DN200 by completing it with proper adapters.
More informationA. ENGINE ASSEMBLY. Page 1 of 14 CREATIVE EQUIPMENT CC ILLUSTRATED PARTS LIST
A. ENGINE ASSEMBLY Page 1 of 14 # PART # DESCRIPTION QTY # PART # DESCRIPTION QTY 1 TL52-52-52J5200.1-6 Cylinder 1 23 TL52-B15301528050 Seal 15*28*4.5 1 2 TL52-52-524500.3.1 Inlet pipe 1 24 TL52-4500.1-5
More informationTEX. Spare parts list. Handheld pneumatic pick hammers 03PS Atlas Copco Construction Tools AB No
TEX 0PS Spare parts list Handheld pneumatic pick hammers 0 Atlas Copco Construction Tools AB No. 9800 0976 0 004 TEX 0PS Contents Contents General information................................................................
More informationSERVICE PARTS MANUAL
SERVICE PARTS MANUAL 8 SERIES SNOW PLOW FOR SERIAL NUMBERS AFTER 8D100000 00 Sno-Way International 9100G TABLE OF CONTENTS PAGE DEFLECTORS... POWER PACK... HYDRAULIC POWER UNIT... LIFT CYLINDER... ANGLE
More informationSB 52. Spare parts list. Hydraulic breakers Atlas Copco Construction Tools AB No e
SB Spare parts list Hydraulic breakers 0 Atlas Copco Construction Tools AB No. 900 09 0e 00 SB Contents Contents General information................................................................ Spare
More informationSB 152. Spare parts list. Hydraulic breakers Atlas Copco Construction Tools AB No f
SB Spare parts list Hydraulic breakers 0 Atlas Copco Construction Tools AB No. 900 00 0f 00 SB Contents Contents General information................................................................ Spare
More informationFloat Flow Meter. Flow measurement for translucent liquids and gases DN10 to DN65 mm. Technical data Orifice DN 10 to 65
Float Flow Meter Flow measurement for translucent liquids and gases DN10 to DN65 mm If a medium sufficient flow rate flows from bottom to top through a vertically inserted measuring tube, then the floated
More informationRanger 33cc 16" Chain Saw UT Page 1 of 14 Accessories
Ranger 33cc 16" Chain Saw UT-10926 Page 1 of 14 Accessories Ranger 33cc 16" Chain Saw UT-10926 Page 2 of 14 Accessories Ref # Part Number Qty S/P/F Description PT12371MD 1 Guide Bar (Power Tip)) 12" (3/8")
More informationSpare part catalogue GB 03/2007. Wall-hung boilers ecotec exclusive 832, 838 VUW 326/4-7 VUW 386/4-7
Spare part catalogue 0020037555.03 GB 03/2007 Wall-hung boilers ecotec exclusive 832, 838 VUW 326/4-7 VUW 386/4-7 Content General view of sheet Page 3 04 Burner Page 4 06 Heat exchanger Page 6 07 Casing
More informationEC 60T. Spare parts list. Hydraulic breakers. EC 60T s/n BES Construction Tools PC AB No
EC 60T Spare parts list Hydraulic breakers EC 60T s/n BES095068 2018 Construction Tools PC AB No. 9864001001 2018-02 Service, repair and wear part kits Label kit 1 Seal kit 3 Mechanical Hydraulic breaker
More informationSB 202. Spare parts list Hydraulic breakers. SB 202 s/n BES Construction Tools PC AB No
SB 202 Spare parts list Hydraulic breakers SB 202 s/n BES051618 2018 Construction Tools PC AB No. 9800172001 2018-01 General information This spare parts list applies to the following: Part number 8460030050
More informationLiquid Level Monitoring System LW4/LW5 - Low or High Level Control
Liquid Level Monitoring System /LW5 - Low or High Level Control Technical Bulletin and LW5 are self-contained units intended for liquid level monitoring at the sight glass or plugged connection of vessels,
More informationTEX 07PE. Spare parts list. Handheld pneumatic pick hammers. Valid from serial number
TEX 07PE Spare parts list Handheld pneumatic pick hammers TEX 07PE TEX 07PE FSH Valid from serial number 0009 0009 0 Atlas Copco Construction Tools AB No. 9800 08 0a 0005 TEX 07PE Contents Contents General
More information"PVL" SERIES. Fixed Displacement - Single PVL1. Up to 5 MPa (730 PSI), 10.6 cm /rev (.647 CU.IN./rev)
"PVL" SERIES Fixed Displacement - Single PVL Up to 5 (70 ), cm /rev (7 CU.IN./rev) Pub. EC-0 The PVL series single pumps are designed for use with small size machine tools requiring comparatively low pressure
More informationDIP. Spare parts list. Centrifugal pumps 25, 25-US, 35, 35-US, 65, 65-US Atlas Copco Construction Tools AB No c
DIP 5, 5US, 35, 35US, 65, 65US Spare parts list Centrifugal pumps 0 Atlas Copco Construction Tools AB No. 9800 5 0c 003 DIP 5, 5US, 35, 35US, 65, 65US Contents Contents General information................................................................
More informationPressure reducing valve. Pressure reducing valve in straightway form NPS 1-6 ARI-PREDU - ANSI
Pressure reducing valve in straightway form NPS 1-6 ARI-PREDU - ANSI Pressure reducing valve ARI-PREDU - ANSI Pressure regulating valve, straight through with diaphragm actuator DMA Actuator with rolling
More informationVLT Line Filter MCC 107 EMC Filter Series VLT Midi Drive FC 280 (K1 K3)
These instructions provide technical and installation information for the MCC 107 EMC filter series. Only Danfoss qualified personnel is allowed to install this equipment. The personnel must be familiar
More informationSpare parts list. Handheld pneumatic pick hammers CP 0222 CHIT, CP 0222 CHIT BS, CP 0222 CHOT BS.
Spare parts list Handheld pneumatic pick hammers CP 0 CHIT, CP 0 CHIT, CP 0 CHOT www.cp.com CP 0 CHIT, CP 0 CHIT, CP 0 CHOT 9800 00 0 CP 0 CHIT, CP 0 CHIT, CP 0 CHOT Contents Contents General information...............................................................
More informationModulating controlled actuator AME 11
Data sheet Modulating controlled actuator AME 11 Description In addition to basic function such as manual control and position indication, the actuators are also equipped with force sensitive switch-off
More informationAK-SM 720 Boolean logic REFRIGERATION AND AIR CONDITIONING. User guide
AK-SM 720 Boolean logic REFRIGERATION AND AIR CONDITIONING User guide Application The function is contained in System manager type AK-SM 720 and can be used for user-defined functions. The functions can
More informationFlow control valves Series SCU, MCU, SVU, MVU, SCO, MCO
S E R I E S SCU MCU SVU MVU SCO Flow control valves Series SCU, MCU, SVU, MVU, SCO, Unidirectional and bidirectional banjo flow controllers Ports M, G1/8, G1/4, G3/8, G1/2 A U T O M A T I C These unidirectional
More informationM3P..G/A, M3P..F/A Modulating control valves (PN16) for chilled and hot water systems
MP..G/A, MP..F/A Modulating control valves (PN) for chilled and hot water systems Three-way or straight-through valves with magnetic actuators for modulating control of chilled and hot water systems. Short
More informationSpare Parts List Hydraulic Hammer. HM 720 Eco (V)
Spare Parts List Hydraulic Hammer HM 720 Eco (V) Pt. Id. No. 3361 8557 11 Valid from: 09/2003 GB Spare Parts List Hydraulic Hammers HM 720 Eco HM 720 Eco V E Atlas Copco Construction Tools GmbH Atlas
More informationMPreC - Pressure Relief Device Order specification sheet
- Pressure Relief Device Order specification sheet -Series LARGE MESSKO PRESSURE RELIEF DEVICE Complete the Order-N o by choosing the specific add-on s: e.g.: LMPRD 685-08-22-N01-00 Order-N o : Parameter
More informationTPV 1200 BTB. Variable Displacement Closed Loop System Axial Piston Compact Tandem Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 156 / 1214 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES THE PRODUCTION LINE OF HANSA-TMP Variable Displacement Closed Loop System Axial Piston Compact Tandem Pump CONTENTS General Information...
More informationHERZ STRÖMAX GM/GML/GR STRÖMAX-GM/GML Circuit Control Valve with test points STRÖMAX-GR Circuit Control Valve Data sheet STRÖMAX GM/GML/GR, Issue 0215
HERZ STRÖMAX 7GM/GML/GR HERZ STRÖMAX GM/GML/GR STRÖMAX-GM/GML Circuit Control Valve with test points STRÖMAX-GR Circuit Control Valve Data sheet STRÖMAX GM/GML/GR, Issue 0 H Rp L SW L L Dimensions in mm
More informationThe ECL Apex 20 is operated by means of either a PC or the ECL Apex Web Panel. Temperature input signals are based on Pt 1000 or 0-10 V.
ECL Apex 20 controller and ECA 20 (ECL Apex Web Panel) Description ECL Apex 20 and ECA 20 ECL Apex 20 The ECL Apex 20 and the ECA 20 (ECL Apex Web Panel) are used in large district heating applications.
More informationSpare parts list. Forward and reversible plate MV 220, Valid from serial number. MV 245 Hatz Electric start
Spare parts list Forward and reversible plate MV 0, MV 0 Honda MV Hatz Electric start MV 0 Honda MV Hatz Electric start Valid from serial number 0000 0000 BGF000000 BGF000000 www.cp.com MV 0, 00 0 0c MV
More informationELIMINATOR Hermetic burn-out filter drier Type DAS
Data sheet ELIMINATOR Hermetic burn-out filter drier DAS ELIMINATOR Hermetic burn-out filter driers type DAS are used in the suction line to clean up refrigeration and air conditioning systems after a
More informationBottom Loading & Recirculation Adapters
SM6958 March 2010 Aerospace Group Conveyance Systems Division Carter Brand Ground Fueling Equipment Applicable additional manuals: None Maintenance & Repair Manual Bottom Loading & Recirculation Adapters
More informationImmersion Temperature Sensors
1 782 1782P01 Symaro Immersion Temperature Sensors QAE2164 QAE2174 Active sensors for acquiring the water temperature in pipes and tanks Operating voltage AC 24 V or DC 13535 V Signal output DC 010 V or
More informationBARE SHAFT PUMPS AND MOTOR PUMPS
APPLICATIONS Air Conditioning Heating and ventilation Refrigeration Fire protection Plumbing Water Circulation Transfer and Irrigation Pressure Boosting Process Industries Water Treatment and Supply DESIGN
More informationOnline version - not for reprint
(0) A Crankcase, Cylinder... X Tools, Extras... B Rewind starter... C Rewind starter ErgoStart... D Muffler... E Ignition system, Clutch... F Engine housing (Wrap around handle)... G Engine housing (Wrap
More informationLenntech BMP GRUNDFOS DATA BOOKLET. High-pressure piston pumps 50/60 Hz
Lenntech GRUNDFOS DATA BOOKLET BMP High-pressure piston pumps 50/60 Hz Contents Product data Introduction Page 3 Features and benefits Page 3 Applications Page 3 Pumped liquids Page 3 key Page 4 Motor
More informationPNEUMATIC CRIMPER PC 12-8B OPERATING MANUAL
PNEUMATIC CRIMPER PC 12-8B OPERATING MANUAL CONTENTS www.americanelectrical.com SAFETY BASIC INFORMATION... 1 SYMBOLS.1 OPERATION OF MACHINE & POSSIBLE DANGERS. 1 DESIGNATED USE. 2 DANGERS 2 PLACES FOR
More informationRA-N Radiator Valves with Integrated Presetting
Data Sheet RA-N valve bodies are manufactured from brass with nickel lating. Alication The ressure in of the gland seal is of chromium steel and works in a lifetime lubricated O-ring. The comlete gland
More informationInline filter. Features: RE 51402/09.10 Replaces: Types 100 FLEN 0160 to 0630; 100 FLE 0045, 0055, 0120
Inline filter RE 50/09.0 Replaces: 0.09 / Types 00 FLEN 060 to 060; 00 FLE 005, 0055, 00 Nominal sizes according to DIN 550: 060 to 060 Nominal sizes according to BRFS: 005, 0055, 00 Nominal pressure 00
More information3000M UT Page 1 of 28 Air Cleaner
3000M UT-26021 Page 1 of 28 Air Cleaner 3000M UT-26021 Page 2 of 28 Air Cleaner Ref # Part Number Qty S/P/F Description 175 GM240308 1 CLEANER ASSY Includes ref 178 thru 182 176 GM002811 1 SCREW & WASHER
More informationLCD 500,1500. Spare parts list. Handheld core drills. Valid from serial number Construction Tools PC AB No
LCD 500,1500 Spare parts list Handheld core drills LCD 500 LCD 500 LCD 1500 Valid from serial number BGF0006875 BGF0006875 BGF0006875 2015 Construction Tools PC AB No. 3392 5193 01 2015-06 General information
More informationRL-H80 PARTS LIST # K
RL-H80 PARTS LIST # 102837K USE THIS PARTS LIST FOR: Hoist Serial Number: 2733 to For older hoists use the following: Parts List No. 102837G for Serial Number 2485 to 2732 IF YOUR HOIST DOES NOT FALL WITHIN
More informationSpare parts list. Forward and reversible plate MV 305, Valid from serial number. MV 305 Honda 600 mm MV 320 Hatz 600 mm
Spare parts list Forward and reversible plate MV 0, 0 MV 0 Honda 00 mm MV 0 Hatz 00 mm MV 0 Honda 00 mm MV 0 Hatz 00 mm Valid from serial number 0000 0000 BGF000000 BGF000000 www.cp.com MV 0, 0 00 00 0c
More information26360, NAMUR. Technical data
66, 87 NAMUR /-, /- and / directional control valves Operation: elektromagnetic Indirectly controlled soft seal spool valves Port size: G/ NAMUR-Interface For single and double operated actuators Manual
More informationThermostat KP. Data sheet. The KP Thermostats are single-pole, doublethrow (SPDT) temperature-operated electric switches.
Data sheet Thermostat KP The KP Thermostats are single-pole, doublethrow (SPDT) temperature-operated electric switches. They can be connected directly to a single-phase AC motor of up to approx. 2 kw or
More informationVane wheel probe BFA25 for flow measurement of gases and liquids with integrated, configurable transducer UFA in Ex-d housing
Vane wheel probe BFA25 for flow measurement of gases and liquids with egrated, configurable transducer UFA in Ex-d housing Drawing 5 Vane wheel flow probe BFA25 (Dimensions see Page 3) Measurable variables
More informationSERVICE PARTS MANUAL
SERVICE PARTS MANUAL DX SERIES SNOW PLOW FOR SERIES SNOW PLOWS SERIAL NUMBERS AFTER DX0000 00 Sno-Way International 0G TABLE OF CONTENTS Page HYDRAULIC SYSTEM (DX)... POWER PACK FRAME... 3 BLADES... LIFT
More informationLevel- and temperature sensor Nivotemp NT M-XP
Level- and temperature sensor Nivotemp NT M-XP Fluidcontrol In hydraulics and lubrication technology the fill level of oil tanks needs to be monitored continuously. Here, modern factory automation requires
More information200 Chain Saw UT Page 1 of 12 Carburetor
200 Chain Saw UT-10690 Page 1 of 12 Carburetor 200 Chain Saw UT-10690 Page 2 of 12 Carburetor Ref # Part Number Qty S/P/F Description 1 02768 1 Repair Kit 02773 1 Oil Pump Plunger Kit 2 02768 1 Repair
More informationJS120 Single Axis Fingertip Joystick. Technical Information
JS120 Single Axis Fingertip Joystick Technical Information Revisions Version Revisions Date Page Change Rev. 2 July, 2009 8, 11 Corrected connector pin assignments and added output voltage curve DA 13
More informationCompact Bellows Pumps
Compact Bellows Pumps Compact Bellows Metering Pumps were specifically designed for metering applications requiring low discharge pressures. Compact pumps have been successfully applied in photo, X-ray
More informationSMD 1B / SMD 2 / SMD 3 flow meters
1-3021-EN Modular design for oil circulating lubrication systems with gearwheel-type flow indicator and bypass system SMD 1B SMD 2 SMD 3 Example of SMD in a stainless steel cabinet Application Flow meters
More informationDIRbuilder Quick Guide Tips & Tricks for DIRbuilder usage
DIRbuilder Quick Guide Tips & Tricks for DIRbuilder usage DIRbuilder is the new free online selection tool developed for easening your selection of valves. This guideline takes you through the features
More informationTEX. Spare parts list. Handheld pneumatic pick hammers 12PE, 12PER Atlas Copco Construction Tools AB No f
TEX PE, PER Spare parts list Handheld pneumatic pick hammers 0 Atlas Copco Construction Tools AB No. 9800 08 0f 00 TEX PE, PER Contents Contents General information................................................................
More informationEB7650TH 76CC BACKPACKER BLOWER 4-STROKE
10-2014 EB7650TH 76CC BACKPACKER BLOWER 4-STROKE 49 50 48 52 53 51 A09 31 32 45 44 43 47 46 39 41 30 33 34 35 37 36 38 27 28 29 5 6 7 8 10 11 12 13 15 17 16 18 19 14 2 1 20 21 55 22 23 24 239 238 A08 56
More informationTimken Lubrication Delivery Systems. Friction management solutions SM to keep systems running smoothly
Timken Lubrication Delivery Systems Friction management solutions SM to keep systems running smoothly G-Power and M-Power Single-Point and C-Power Centralized Multi-Point Lubricators Proper lubrication
More informationPRESSURE RELIEF DEVICE ORDERING SPECIFICATIONS.
MESSKO MPreC PRESSURE RELIEF DEVICE ORDERING SPECIFICATIONS. MESSKO MPreC -Series LARGE MESSKO PRESSURE RELIEF DEVICE (LMPRD) Operating pressure Project/Reference: Gasket material MPreC Typ 4 psi; 0.28
More information656 W. Spare parts list. Pusher leg rockdrills Atlas Copco Construction Tools AB No a
RH 656 W Spare parts list Pusher leg rockdrills 00 Atlas Copco Construction Tools AB No. 9800 0690 0a 00-05-0 RH 656 W Contents Contents General information................................................................
More informationSPH / MA and MA2 components MCS / MA multi-connections. Technical data sheet
SPH / MA and MA2 components MCS / MA multi-connections Technical data sheet SPH / MA and MA2 components for MCS / MA automatic multi-connections Nominal bore 04, 06, 08, 12, 15, 20, 25, 37, 50 and 75 mm
More informationSPARE PARTS LIST CP COMPRESSOR. Model CPD CPD 75
SPARE PARTS LIST CP COMPRESSOR Model CPD 75-00 EN 05 0 5 CPD 75 CONTENTS Title Page MAINTENANCE HOW TO READ THIS SPARE PART LIST? MAINTENANCE KITS STANDARD UNITS MOTOR-COMPRESSOR UNIT -7 AIR CIRCUIT -9
More informationOval Gear Meter OGM PLUS
Precise volume measurement Reliable process control High-grade materials Resistant to chemicals Not affected by changes in viscosity Elados EMP pump coordinated flow rates Direct connection to an EMP E60
More informationElectrical Actuators
4 891 SSB without auxiliary switch SSB1 with auxiliary switch Electrical Actuators for small valves types VVP45, VXP45, VMP45 (max D25, k VS = 63 m 3 /h) SSB31 SSB81 SSB61 SSB31 operating voltage AC 230
More informationPressure reducing valve. Pressure reducing valve in straightway form NPS 1-6 ARI-PREDU - ANSI
Pressure reducing valve in straightway form NPS 1-6 Pressure reducing valve Pressure regulating valve, straight through with diaphragm actuator DMA Actuator with rolling diaphragm Cast steel Fig. 701 Page
More informationYP40TX (Q9C9) U.S.A. 1N9C9-110E1
YP40TX () U.S.A. 1N9C9-110E1 ( ) YP40TX PARTS CATALOGUE 2014 by Yamaha Motor Co., Ltd. 1st edition, May 2014 All rights reserved. Any reprinting or unauthorized use without the written permission of Yamaha
More informationElectromechanical pressure switches
Presentation Electromechanical pressure switches For control circuits, types ACW and ADW Presentation Pressure switches type ACW and ADW are switches for control circuits, with an adjustable differential.
More informationFloat switch 298. Use. Variants. + Sturdy construction with very few moving parts. + Standard flange with different hole patterns
Float switch 298 + Sturdy construction with very few moving parts + Standard flange with different hole patterns + Operating temperature -40 C to +85 C + Long lifetime due to wear-free reed contacts +
More informationCS3314 Chain Saw UT R Page 1 of 12 Carburetor & Accessories
CS3314 Chain Saw UT-10734-R Page 1 of 12 Carburetor & Accessories CS3314 Chain Saw UT-10734-R Page 2 of 12 Carburetor & Accessories Ref # Part Number Qty S/P/F Description A03904 1 /P Gasket/Diaphragm
More informationBalancing valve PN 16 and PN 25 DN
STAF, STAF-SG Balancing valve PN and PN DN 0-00 Pressurisation & Water Quality Balancing & Control Thermostatic Control ENGINEERING ADVANTAGE A flanged, cast iron (STAF) and ductile iron (STAF-SG) balancing
More informationISO STAR Solenoid & pilot actuated spool valves Sub-base 5/2 & 5/3, ISO #1... ISO #3
ISO STR Solenoid & pilot actuated spool valves Sub-base 5/2 & 5/3, ISO #... ISO #3 Specially coated glandless spool and sleeve for long life vailable with integral flow regulators on ISO # & #2 sizes ow
More informationPARTS-, SPARE & MATERIAL LIST Component: type & version LPU-D-POWER-ON/OFF 230 VAC 50/60 Hz v2a Material no.: 160G4182 Alt.: 1
Page 1 of 6 Notes: All items with stated material number can be purchased as spare parts. When ordering spare parts: please state material number. Document numbers refered to: 160G9358 Posnr Material Description/
More informationSECTION FIVE - SANITARY - MANHOLES
Sealtight & 4 Lug Assemblies* ITEM # DESCRIPTION PART # 1 2 3 4 6 7 8 9 10 DUST COVER VENT (not shown) STAINLESS STEEL DUST COVER HINGE PIN (3/ SEALTIGHT) HINGE PIN (/8 4 LUG) STUD (3/ SEALTIGHT) STUD
More information5/2 and 5/3 Directional-control valves, Series TC 15, G 1/4
5/2 and 5/3 Directional-control valves, Series TC 15, G 1/4 Products 5/2 Directional-control valve, single valve, electrical connection M8 (4 poles) 5/3 Directional-control valve, single valve, electrical
More informationModel QRS CPVS
SPARE PARTS LIST EN CP COMPRESSOR Model QRS 0-5 - 0 CPVS 0-5 - 0 6 05 50 65 KEY - Door Panel: 655900 Lock - Door Panel: 005076 QRS 0 CONTENTS Title Page MAINTENANCE HOW TO READ THIS SPARE PART LIST? KIT
More informationMaria Splitt Only for informational purpose, will not be replaced in case of changes Print Date: 1/23/2013 1:01 PM Z-No Mat-No. Change Master Quantity Unit Description Specification Order Type Status 1
More informationSTANDARD CARTRIDGE VALVES 2/2-WAY
STNDRD CRTRIDGE VLVES -WY SERIES NG NG ulletin - DESIGNTION SYMOL PGE General Description and Operating Principle Specifications and Characteristic Parameters Typical Characteristic Curves - -way Cartridge
More informationOperating Instruction
Level and Pressure Operating Instruction VEGASWING 71 A Contents Contents Safety information... 2 1 Product description 1.1 Function and configuration... 3 1.2 Functional principle... 3 1.3 Technical data...
More informationOnline version - not for reprint
(0) A Engine housing... B Cylinder... B Cylinder... C Rewind starter, Ignition system... C Rewind starter, Ignition system... D Chain brake... E Quick tensioner parts... F Air filter, Cover... G Handle
More informationCI-tronic Reversing contactor Type RCI
Data sheet CI-tronic Reversing contactor Type RCI RCI reversing contactors are designed for demanding forward/reverse control of three-phase AC motors. The zero cross switching method ensures very fast
More informationREFRIGERATION AND AIR CONDITIONING. On Site Guide AK2-SC 255
REFRIGERATION AND AIR CONDITIONING On Site Guide AK2-SC 255 How to Use This Guide Read this Guide completely as you install and start up your new AK2-SC 255 controller. The guide will give you thorough
More informationXL Chain Saw UT Page 1 of 10 Carburetor
XL Chain Saw UT-10722 Page 1 of 10 Carburetor XL Chain Saw UT-10722 Page 2 of 10 Carburetor Ref # Part Number Qty S/P/F Description 1 A03905 1 /P Repair Kit 02773 1 Oil Pump Plunger Kit 2 A03905 1 /P Repair
More informationliving connect, Z-Wave Certified Electronic Radiator
living connect, Z-Wave Certified Electronic Radiator Thermostat Application living connect is battery powered, compact and very easy to operate with only three buttons on the front. This documents provides
More informationOld documentation - Only for your information! Product is not available anymore!
Double solenoid valve Control and safety combination valve Servo pressure controller - / 7. Printed in Germany Rösler Druck Edition 0.08 Nr. 09 8 Technical description The DUNGS multiple actuator DMV-SE...
More informationPressure switch KP. Data sheet
Data sheet Pressure switch KP The KP pressure switches can be used as safety switches against too low a suction pressure and / or too high a discharge pressure in refrigeration and air conditioning systems.
More informationMini slides SLT/SLS/SLF
Mini slides SLT/SLS/SLF Precision, rigid guide Highly flexible Adjustable end position cushioning 03/10 Subject to change Products 04/05 1 / 1 Mini slides SLT/SLS/SLF Features SLS SLF SLT SLT/SLS/SLF SLT
More informationMCX08M2 Programmable controller
Data sheet MCX08M2 Programmable controller MCX08M2 is an electronic controller that holds all the typical functionalities of MCX controllers in the compact size of 8 DIN modules: programmability connection
More informationTHERMASGARD TM 65. Immersion screw-in duct temperature measuring transducer, calibratable, with multi-range switching and active output TECHNICAL DATA
Patented quality product (Immersion sensor patent no. DE 10 2012 017 500.0) Calibratable temperature measuring transducer THERMASGARD with eight switchable measuring ranges, continuous linear output, enclosure
More information