SUCTION FILTERS. PRESSURE (ISO :2002) Collapse, differential for the fi lter element (ISO 2941): 1 MPa (10 bar)

Transcription

1 COMPONENTS SUCTION ILTERS SD MATERIALS Cover & housing: Anodized aluminium alloy or 6&6 only: Cover: anodized aluminium alloy Housing: steel ypass valve: Polyammide Seals: NR Nitrile (KM on request fl uoroelastomer) Indicator housing: rass PRESSURE (ISO 077:00) Collapse, differential for the fi lter element (ISO 9): MPa (0 bar) YPASS VALVE Setting: 5 kpa (0,5 bar) ± 0% APPLICATION EXAMPLE WORKING TEMPERATURE rom 5 to +0 C COMPATIILITY (ISO 9) ull with fl uids: HHHLHMHVHTG (according to ISO 67/) or fl uids different than the above mentioned, please contact our Sales Department.

2 SD SUCTION ILTERS INSTALLATION DRAWING SD 5 SD 6 6 R 0 H H H H6 D H5 H 6 E D 90 H H H D H7 H R 6 E D N.. elbow pipe not supplied. Tank mounting pattern 5 ø D ø D 5 D5 ILTER HOUSING D D D D D5 E H H H H H5 H6 R kg SD / M5 60 6,5 96,5 05, SD / 8 8 M ,6 SD M ,7 SD / M ,5 SD5 / M0 7, , SD6 / ,0 SD ,0

3 SUCTION ILTERS ORDERING AND OPTION CHART SD S D TYPE = ILTER COMPLETE = ILTER HOUSING AMILY NOMINAL SIZE & LENGTH ELENT AMILY SIZE & LENGTH E R D PORT TYPE = SP thread N = NPT thread S = SAE thread = SAE flange 000 psi, metric screws PORT SIZE 0 = /" 06 = /" 08 = " = " / 0 = " / 8 = " / = " YPASS VALVE W = without A = 5 kpa (0,5 bar) SEALS N = NR Nitrile = KM luoroelastomer SEALS N = NR = KM ILTER DIA ILTER DIA = metal wire mesh 60 m = w. mesh 60 m M = metal wire mesh 90 m M = w. mesh 90 m = metal wire mesh 50 m = w. mesh 50 m 08 = /8" seat, plugged = vacuum gauge, bottom connection 9 = SPDT, vacuum switch X X ACCESSORIES XX = no accessory available XX XX XX XX XX XX XX ILTER ELENT A C ERD 5 8/ 70 kg 0,0 Area (cm ) Media M+ 5 ERD ,0 60 ERD ,5 70 C ERD ,70.0 ERD ,50.0 ERD6 0 7/85 500, ERD6 96, 896, A

4 SD SUCTION ILTERS LUID SPEED when selecting the fi lter size, we suggest to consider also the max recommended fl uid speed (in suction lines normally 0,< v < m/s) Recommended range 00 LOW RATE [] ,< v < m/s / / / / / PORT SIZE PRESSURE DROP CURVES ( p) The Assembly Pressure Drop ( p) is obtained by adding the pressure drop values of the ilter Housing and of the Clean ilter Element corresponding to the considered low Rate and it must be lower than kpa (0,0 bar). ILTER HOUSING PRESSURE DROP (mainly depending on the port size) 0,0 0,0 /" /" " SD 0,0 0,0 SD 566 / / / 0,0 0, CLEAN ILTER ELENT PRESSURE DROP WITH DIA (depending both on the internal diameter of the element and on the fi lter media) 0,0 0,0 ERD M 0, N.. All the curves have been obtained with mineral oil having a kinematic viscosity 0 cst and specific gravity 0,9 kg/dm ; for fluids with different features, please consider the factors described in the first part of this catalogue. All the curves are obtained from test done at the UI HYDRAULIC DIVISION Laboratory, according to the specification ISO 968:005. In case of discrepancy, please check the contamination level, viscosity and features of the fluid in use.

5 CLEAN ILTER ELENT PRESSURE DROP WITH M+ DIA (depending both on the internal diameter of the element and on the filter media) SUCTION ILTERS SD 0,0 0,0 M ERD 0,0 0,0 M ERD 0,0 0, ,0 0,0 0,0 ERD M 0,0 0,0 0,0 M ERD ,0 0,0 0,0 M ERD 6 0,0 0,0 0,0 ERD 6 M YPASS VALVE PRESSURE DROP When selecting the filter size, these curves must be taken into account if it is foreseen that any flow peak is to be absorbed by the bypass valve, it also must be of proper configuration to avoid pressure peaks. The valve pressure drop is directly proportional to fluid specific gravity. 0,6 60 SD 0,6 60 SD 0,5 5 0,5 5 0, 0 0, 0 0,5 5 0, ,6 60 SD SD 566 0,6 60 0,5 5 0,5 5 0, 0 0, 0 0,5 5 0,

6 SD SUCTION ILTERS A visual or electrical indicator allows monitoring of the element condition, and gives an indication of the proper time for replacement. The port for the indicator is a standard feature. STRONG CONSTRUCTION The strong filter housing makes the SD filters particularly suitable for applications where each component must provide the highest reliability. LEXIILITY O ASSEMLING A second inlet port, supplied plugged, permits you to easily solve special installation needs. NO LEAKS The end caps with captive Oring ensure a perfect sealing between filter element and housing. or further technical informations and other options see page 87. SPARE SEAL KIT NR KM SD SD SERIES SD SD SD SD SERIES 9 SD S D ILTER HOUSING X X ILTER ELENT E R D SPARE PARTS ELENTS (or filling up see table Ordering and option chart ) Is this datasheet the latest release? Please check on our website. Technical data subject to variations without prior notice. SD EN 0/0