QUICK START GUIDE. Display Evaluation Kit 10.7 and up PLDEK_F5-HBZ3

Transcription

1 QUICK START GUIDE Display Evaluation Kit 10.7 and up PLDEK_F5-HBZ3 Part-No ,

2 1 Safety Points Warning: To avoid risk of electric shock or damage to the display, disconnect the display module from its power source before handling it. Do not touch the connections or circuits whilst the display is in operation. Caution: Follow ESD handling procedures to avoid circuit damage. Use a grounded wrist strap. Do not press on the display panel or its edges as damage can result. Important Notice The Plastic Logic Display Evaluation Kit ( the Kit ) is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by Plastic Logic to be a finished end-product fit for general consumer use. Persons handling the Kit must have electronics training and observe good engineering practice standards. As such, the kit being provided is not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards. The kit does not fall within the scope of the European directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives. 2 About this document This document is a quick start guide for 10.7 and up Evaluation Kit (PLDEK_F5- HBZ3). It is only to be used for kits containing Z3 of the Hummingbird board. It is intended to give sufficient information to: 1. Safely unpack and power up the PLDEK. 2. Start displaying images in.png format. 3 Getting Started Prior to unpacking the kit, the user is strongly urged to take appropriate ESD and safety precautions. 3.1 Unpacking the Kit The PLDEK kit is shipped with the items listed in Fehler! Verweisquelle konnte nicht gefunden werden.the following table.

3 Please ensure that the items listed have been included in your kit. Remove the PLDEK from the anti-static bags and perform a visual inspection. Number Item Description 1 Board 1 Freescale i.mx508 Eval Board. Green PCB. MCIMX50EVK Rev D. 2 Board 2 Plastic Logic Hummingbird Z3 board. 3 Board 3 (dual display kit only) Plastic Logic 2 nd Power board for usage of dual displays (15.4 ) or two 10.7 displays in parallel. 4 SD Card Operating system including software to control display electronic, folder for.png images and waveforms. At delivery status the card is mounted in board 1. 5 Ribbon cable Ribbon cables to connect the Gate and Source SAYUs to the Hummingbird board 6 Gate SAYU Small PCB. Labeled Plastic Logic Diablo Gate SAYU V Source SAYU Small PCB. Labeled Plastic Logic Diablo Source SAYU V Power supply 5.0V/4.0A power supply 9 USB cable to connect to Freescale board via micro USB port 10 i.mx50 Quick Start Guide + CD Getting started Booklet & CD from Freescale 11 PLDEK Data CD User Guide, initial waveform(s),.png images and USB driver for Win XP, color conversion tool Ribbon Cable Hummingbird Z3 (Board 2) SD Card Socket Micro USB 5V Power Supply 5V Power Slide switch

4 Display 2 2 nd Power Board (Dual display kit only) 3.2 Connecting up the Kit Freescale i.mx508 Eval. Board (Board 1) Reset Button Ethernet Connector Serial Connector 1. Check that the connectors on both ends of each ribbon cable are properly engaged into their respective box headers. Eval. Kit Gate & Source Connectors Display Connectors 2. Ensure that the display connectors are fully engaged with their respective flip-lock connectors on the Eval. Kit Gate & Source connectors (red arrows). If not, lift up the black plastic flip-lock, fully insert the display connector and push down to close the flip-lock. 3. Please ensure that display 1 gate connector is connected to the display gate and that display 1 source connector is connected to the source. If you have a dual display kit, please do the same with connectors of display 2. Connecting these the wrong way round will probably irreparably damage the display. 4. Connect the 5V power cable to the processor board 1 (N.B. This will supply power for all boards). (Note: The power connector on the Hummingbird Z3 board 2 is only for initial programming mode). 3.3 System boot and image display 1. Turn on the power at the mains and move the Freescale boards power slider switch to on (default position at delivery). 2. A red LED on the Freescale Board should start flashing and two green LEDs (D3 & D4) on the Hummingbird board should be illuminated. 3. Now wait for approximately 45 seconds for the Freescale processor to boot and load the operating system. 4. Shortly afterwards, the Plastic Logic display should start being updated with a sequence of images at approximately 5 second intervals.

5 For further information please check the user guide for the 10.7 and up Evaluation Kit (PLDEK_F5-HBZ3) Part-No , on the PLDEK Data CD.