Scritto Da: Valentina Cerruty

Transcription

1 Wii U GamePad LCD Display Replacement Replace the LCD display in order to fixed the broken LCD display Scritto Da: Valentina Cerruty ifixit CC BY-NC-SA it.ifixit.com Pagina 1 di 13

2 INTRODUZIONE This guide will help you to replace the LCD display. For this replacement, you will need to use a #00 Phillips screwdriver and a small Triwing (Y) screwdriver. STRUMENTI: Phillips #0 Screwdriver (1) Y1 Tri-point Screwdriver (1) Tweezers (1) COMPONENTI: Wii U GamePad Display Assembly (1) Wii U GamePad LCD (1) ifixit CC BY-NC-SA it.ifixit.com Pagina 2 di 13

3 Passo 1 Battery Place Gamepad face down and remove the two 4.7 mm screws with a Phillips size #0 screwdriver. Passo 2 Lift and remove the battery plate. ifixit CC BY-NC-SA it.ifixit.com Pagina 3 di 13

4 Passo 3 With your finger, press down and pull back on the battery connector plug. Remove the battery from the battery case. Passo 4 Outer Case Remove 10 9mm screws with Tri-Wing size Y1 screwdriver around the outer case. Lift up on the back of case. Lift gently because the rumble motor in the back of the case is still connected by a cable to the motherboard. ifixit CC BY-NC-SA it.ifixit.com Pagina 4 di 13

5 Passo 5 Unplug outer case rumble motor connector from the motherboard with your fingers. Passo 6 Speakers With your fingers, unplug the left speaker cable from the motherboard. ifixit CC BY-NC-SA it.ifixit.com Pagina 5 di 13

6 Passo 7 Remove the right speaker cable that's connected to the motherboard with the tweezers. Passo 8 Bluetooth Open the top and bottom clasp that connects the white flex cable to the motherboard with the tweezer. Remove the white flex cable with the tweezers. ifixit CC BY-NC-SA it.ifixit.com Pagina 6 di 13

7 Passo 9 With your fingers, lift and remove bluetooth board. Remove the board carefully as there are still two wires attached. Passo 10 Disconnect the black and white wires off of the back of the bluetooth module. ifixit CC BY-NC-SA it.ifixit.com Pagina 7 di 13

8 Passo 11 Lift and remove the bluetooth module. Passo 12 Motherboard Disconnect the analog connector with tweezers. ifixit CC BY-NC-SA it.ifixit.com Pagina 8 di 13

9 Passo 13 Remove the blue connector using tweezers. Passo 14 Carefully lift the black clasp. It is prone to breaking if only lifted from one point. Remove the brown ribbon by using the tweezers. Unclasp small gray ribbon to the left of the brown ribbon. ifixit CC BY-NC-SA it.ifixit.com Pagina 9 di 13

10 Wii U GamePad LCD Display Replacement Passo 15 Remove the small orange ribbon with the tweezers. Passo 16 Remove these two connectors to the motherboard with your fingers. ifixit CC BY-NC-SA it.ifixit.com Pagina 10 di 13

11 Passo 17 Remove the NFC communicator. When removing the NFC communicator, be careful with the small connector on the back side. Remove the small connector plug-in on the back. Passo 18 Remove the remaining three 5.1 mm screws using the Phillips size #0 screwdriver. Lift and remove the mother board. ifixit CC BY-NC-SA it.ifixit.com Pagina 11 di 13

12 Passo 19 LCD Display Remove the four 5.1mm screws using Phillips size #0 screwdriver. Pull the white and black cables away from the display case. Passo 20 Lift and remove the grey display case with your fingers. ifixit CC BY-NC-SA it.ifixit.com Pagina 12 di 13

13 Passo 21 Gently with your fingers, press on the front of the display and it will lift up. Remove the display with your fingers. To reassemble your device, follow these instructions in reverse order. Questo documento è stato generato l'ultima volta su :19:13 AM. ifixit CC BY-NC-SA it.ifixit.com Pagina 13 di 13