Hardware Installation Guide

Transcription

1 Hardware Installation Guide Congratulations on purchasing a LogLogic ppliance! The LogLogic ppliance-based solution enables you to capture and manage log data from all types of sources in your enterprise. LogLogic ppliances install within minutes and begin collecting and aggregating data from connected log sources immediately. Follow these steps to quickly install your LogLogic ppliance. For logging in and configuring your ppliance refer to the LogLogic Installation and Upgrade Guide. Step 1: Unpack and Verify Parts in the Kit Unpack and verify the following parts are available in the kit. Table 1 ppliance Kit Components Item Qty Part Number Description 1. 1 N/ LogLogic ppliance Power cords (Note: LX820 ppliance has only 1 power cord) Rail Kit Null modem cable, D9 F/F, 6 feet Documentation & Supplemental CD Pre-ship FQC Checklist Packing list Rail Kit Components 1. 1 TW1-S G 28 RIL 2. 2 TW1-S djust racket 3. 2 TW1-S djust racket E M5 Nut Plate E M4 Nut Plate TW R M5 x 10.0L screws CS4+10FN M4 x 10.0L screws CS4+4FN M4 x 4.0L screws TW M5 x 10.0L screws PRT NUMER LL E

2 Step 2: ttach Mounting Rail rackets Figure 1 Rail Kit Components Step 2: ttach Mounting Rail rackets The position of chassis and rails with a side view of cabinet with one-2u system is shown below. Figure 2 Side View of the ppliance 1. Remove the two identical main rails and the inner rails from the box. 2. ttach inner rails to chassis (either left or right side) by using M4x4.0L screws. Use 4 screws for 1U and 3 screws for 2U on each side. 2

3 Step 2: ttach Mounting Rail rackets Figure 3 ttach Inner Rails 3. For Cabinet with square mounting holes: ttach and screw in the adjustable rear bracket to the outer rail as shown below (the rear bracket should be movable in front and back). Figure 4 ttach Rear racket 4. Follow the orientation specified below to install the outer rail and rear bracket with screws and nut plates on the cabinet. Tighten the screws (as show in Figure 4) after the whole outer rail set is mounted to the cabinet posts. 3

4 Step 2: ttach Mounting Rail rackets Figure 5 Install Outer Rails 5. For Cabinet with round mounting holes: ttach and screw in the adjustable rear bracket to the outer rail as shown below (the rear bracket should be movable in front and back). Figure 6 ttach Rear racket 6. Follow the orientation specified below to install the outer rail and rear bracket with screws and nut plates on the cabinet. Tighten the screws (as show in Figure 6) after the whole outer rail set is mounted to the cabinet posts. 4

5 Step 2: ttach Mounting Rail rackets Figure 7 Install Outer Rails 7. Slide the chassis into the cabinet by inserting inner rails to the outer rail mounted in the cabinet. Figure 8 Slide the Chassis 5

6 Step 3: Connect Cables Step 3: Connect Cables 1. Connect the power cables (located at the back side of the ppliance) as shown below. Figure 9 Connected Power Cable (LX820-1 Power Cable) Figure 10 Connected Power Cables (for 1U system) Figure 11 Connected Power Cables (for 2U system) 6

7 Step 3: Connect Cables 2. Connect the Ethernet cables (located at the back of the ppliance) as shown below. Note: These cables are not included in the kit. Figure 12 Connected Ethernet Cables (for 1U system) Figure 13 Connected Ethernet Cables (for 2U system) 3. For Setting up with Console Connect one end of the Null modem cable located at the back of the ppliance and attach the other end to a laptop or terminal device, for example, HyperTerminal or putty. Note: This step is required only when you are setting up the ppliance using the Console. If you are setting up with a rowser, skip this step and go to Step 4: Power up the ppliance. Figure 14 Connected Null modem cable (for 1U system) Figure 15 Connected Null modem cable (for 2U system) 7

8 Step 4: Power up the ppliance Step 4: Power up the ppliance 1. Press the Power button (located on the front side). In few seconds, the Power button turns blue as shown below. When the operating system starts booting up, the LEDs show blue color. Figure 16 Power utton (for 1U system) Figure 17 Power utton (for 2U system) 2. Wait for about 3 to 5 minutes for system to boot up. During this time, you can see various messages appearing on the screen. Once the system boots up, the screen displays the following prompt. Figure 18 ppliance ooting Process Completed Congratulations! You have successfully installed the LogLogic ppliance. Step 5: Log into the ppliance For instructions on how to log in to the ppliance using either Web browser or Console, refer to the LogLogic Installation and Upgrade Guide. 8

9 PPENDIX External Hardware Descriptions This appendix provides a series of graphics displaying the external hardware and provides the hardware specifications for the LogLogic family of products. Sorted by ppliance family, every model is described. Contents LX Product Family ST Product Family MX Product Family Note: ll LogLogic 2U ppliances come with mounting slides that you can use to mount to a 19-inch enclosed equipment rack. Hardware such as brackets and screws are provided to secure the ppliances to the 19-inch equipment rack. 9

10 LX Product Family LX Product Family The LX product family includes the following ppliances: LX 820 LX 1020 LX 4020 LX Product Family Specifications Hardware Specifications LX 820 LX 1020 LX 4020 CPU Quad Core Xeon Quad Core Xeon Dual Quad Core Xeon Memory 4 G 6 G 12 G Hard Drive 2x500 G 2x1 T 8x1 T RID * RID 1 RID 1 RID 10 C Power Connections 1 2 (for redundancy) 2 (for redundancy) C Input V Hz V Hz V Hz Power Consumption 120 Watts 160 Watts 440 Watts Heat Dissipation 410 TU/hr 550 TU/hr 1500 TU/hr C Current 120V 120V 120V Operating ltitude -50 to 10,000 ft -16 to 3048 m -50 to 10,000 ft -16 to 3048 m -50 to 10,000 ft -16 to 3048 m Operating Temperature degrees C. (Derate maximum temperature by 1 degree C per 300 meters above sea level) Relative Humidity 20-80% non-condensing 19 Rack Mount Chassis 1U 1U 2U Chassis Mounting Rail kit provided. Rails adjust 28 to 31 and attach to front and rear of rack or cabinet. Caution: Rails cannot be properly mounted if adjusted to under 28. Chassis (W x H x D) 17.5 x 1.75 x 21 inches (44.50 x 4.45 x cm) x 1.75 x 27 inches (43.82 x 4.45 x cm) 17.5 x 3.5 x 28 inches (44.45 x 8.89 x cm) Weight 22 lb / kg 28 lb / kg 52 lb / kg Ethernet 3x10/100/1000 6x10/100/1000 6x10/100/1000 onding Port Labeling Eth0 & Eth1 Eth2 & Eth3; Eth4 & Eth5 Eth2 & Eth3; Eth4 & Eth5 Console Connector (male) (null modem cable provided) 9-pin D-sub 9-pin D-sub 9-pin D-sub * 2U ppliance RID includes a cache memory with internal battery backup. In the event of an unplanned power outage, the battery will protect the integrity of the disk data for a maximum of 72 hours. 10

11 PPENDIX External Hardware Descriptions LX 820 ppliance LX 820 Front Panel ID Description ttention LED Power utton LX 820 Rear Panel C D E F/G H I J ID C D E F G H I J Description Power Source Cooling Fan US Ports (x4) Video Port Serial Port Eth 2 Port Eth 0 Port Eth 1 Port 11

12 LX Product Family LX 1020 ppliance LX 1020 Front Panel ID Description ttention LED Power utton LX 1020 Rear Panel C D E F G/H F I J K L ID Description C Cooling Fan D Power Source E larm Reset F US Ports (x2) G Video Port H Serial Port I Eth 3 and Eth 2 Ports J Eth 1 and Eth 0 Ports K, L Eth 5 and Eth 4 Ports 12

13 PPENDIX External Hardware Descriptions LX 4020 ppliance LX 4020 Front Panel ID Description ttention LED Power utton LX 4020 Rear Panel C D E F G/H F I J K ID C D E F G H I J K Description Power Module Power Source larm Reset US Ports (x2) Video Port Serial Port Eth 3 & Eth 2 Ports Eth 1 & Eth 0 Ports Eth 4 & Eth 5 Ports 13

14 ST Product Family ST Product Family The ST product family includes the following ppliances: ST 1020 ST 2020-SN (Storage rea Network) ST 4020 ST Product Family Specifications Hardware Specifications ST 1020 ST 2020-SN ST 4020 CPU Quad Core Xeon 2 Quad Xeon Dual Quad Core Xeon Memory 6 G 12 G 12 G Hard Drive 2x1 T 2x1 T 8x1 T RID * RID 1 RID 1 RID 5 + Spare C Power Connections 2 (for redundancy) 2 (for redundancy) C Input V Hz V Hz 2 (for redundancy) V Hz Power Consumption 160 Watts 270 Watts 450 Watts Heat Dissipation 550 TU/hr 950 TU/hr 1500 TU/hr C Current 120V 120V 120V Operating ltitude -50 to 10,000 ft -16 to 3048 m -50 to 10,000 ft -16 to 3048 m -50 to 10,000 ft -16 to 3048 m Operating Temperature degrees C. (Derate maximum temperature by 1 degree C per 300 meters above sea level) Relative Humidity 20-80% non-condensing 19 Rack Mount Chassis 1U 1U 2U Chassis mounting Rail kit provided. Each rail adjusts from 28 to 31 and attaches to front and rear of rack or cabinet. Caution: Rails cannot be properly mounted if adjusted to under 28. Chassis (W x H x D) x 1.75 x 27 inches (43.82 x 4.45 x cm) x 1.75 x 27 inches (43.82 x 4.45 x cm) x 3.50 x 28 inches (44.45 x 8.89 x cm) Weight 28 lb / kg 30 lb / kg 52 lb / kg Ethernet 6x10/100/1000 4x10/100/1000 6x10/100/1000 onding Port Labeling Eth2&3; Eth4&5 Eth2&3/FC1&2 Eth2&3; Eth4&5 Console Connector (male) (null modem cable provided) 9-pin D-sub 9-pin D-sub 9-pin D-sub * 2U ppliance RID includes a cache memory with internal battery backup. In the event of an unplanned power outage, the battery will protect the integrity of the disk data for a maximum of 72 hours. 14

15 PPENDIX External Hardware Descriptions ST 1020 ppliance ST 1020 Front Panel ID Description ttention LED Power utton ST 1020 Rear Panel C D E F G/H F I J K L ID Description C Cooling Fan (x2) D Power Source (x2) E larm Reset F US Ports (x2) G Video Port H Serial Port I Eth 3 and Eth 2 Ports J Eth 1 and Eth 0 Ports K, L Eth 5 and Eth 4 Ports 15

16 ST Product Family ST 2020-SN ppliance ST 2020-SN Front Panel ID Description ttention LED Power utton ST 2020-SN Rear Panel C D E F G / H F I /J K /L FC 1& 2 ID Description C Cooling Fan D Power Source (x2) E larm Reset F US Ports (x2) G Video Port H Serial Port I Eth 3 Port J Eth 2 Port K Eth 1 Port L Eth 0 Port FC Fibre Channel 1 & 2 Supported Optical Cable Distances & Types Cable Type and Distance (meters) Rate OM1 OM2 OM3 2Gbps Gbps Gbps

17 PPENDIX External Hardware Descriptions ST 4020 ppliance ST 4020 Front Panel ID Description ttention LED Power utton ST 4020 Rear Panel C D E F G/H F I J K ID C D E F G H I J K Description Power Module Power Source larm Reset US Ports (x2) Video Port Serial Port Eth 3 & Eth 2 Ports Eth 1 & Eth 0 Ports Eth 4 & Eth 5 Ports 17

18 MX Product Family MX Product Family The MX product family contains the MX 3020 and MX 4020 ppliances. MX Product Family Specifications Hardware Specifications MX 3020 MX 4020 CPU Quad Core Xeon Dual Quad Core Xeon Memory 6 G 12 G Hard Drive 8x500 G 8 T RID * RID 10 RID 10 C Power Connections 2 (for redundancy) 2 (for redundancy) C Input V Hz V Hz Power Consumption 450 Watts 440 Watts Heat Dissipation 1500 TU/hr 1500 TU/hr C Current 120V 120V Operating ltitude Operating Temperature -50 to 10,000 ft -16 to 3048 m degrees C. (Derate maximum temparture by 1 degree C per 300 meters above sea level) -50 to 10,000 ft -16 to 3048 m degrees C. Relative Humidity 20-80% non-condensing 20-80% non-condensing 19 Rack Mount Chassis 2U 2U Chassis Mounting Rail kit provided. Rail kit provided. Chassis (W x H x D) Each rail adjusts from 28 to 31 and attaches to front and rear of rack or cabinet. Caution: Rails cannot be properly mounted if adjusted to under x 3.5 x 28 inches x 8.89 x cm Each rail adjusts from 28 to 31 and attaches to front and rear of rack or cabinet. Caution: Rails cannot be properly mounted if adjusted to under x 3.5 x 28 inches x 8.89 x cm Weight 52 lb / kg 52 lb / kg Ethernet 6x10/100/1000 6x10/100/1000 onding Port Labeling Eth2&3/Eth4&5 Eth2&3/Eth4&5 Console Connector (male) (null modem cable provided) 9-pin D-sub 9-pin D-sub * 2U ppliance RID includes a cache memory with internal battery backup. In the event of an unplanned power outage, the battery will protect the integrity of the disk data for a maximum of 72 hours. 18

19 PPENDIX External Hardware Descriptions MX 3020/MX4020 ppliance Note: The pictures below represents MX3020 ppliance. MX 3020/MX 4020 Front Panel ID Description ttention LED Power utton MX 3020/MX 4020 Rear Panel C D E F G/H F I J K ID C D E F G H I J K Description Power Module Power Source larm Reset US Ports (x2) Video Port Serial Port Eth 3 & Eth 2 Ports Eth 1 & Eth 0 Ports Eth 4 & Eth 5 Ports 19

20 MX Product Family 20

21 PPENDIX attery Safety Caution: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer s instructions. 21

22 attery Safety : 22