UBQUITI M-SERIES AIROS V6.X BASIC SETUP PTP AND PTMP

Transcription

1 UBQUITI M-SERIES AIROS V6.X BASIC SETUP PTP AND PTMP PRODUCTS: UBQUITI M-SERIES PRODUCTS (M900 M2 M5) TOPICS COVERED IN THIS KBA: Ubquiti M-series airos v6.x Basic Setup PTP and PTMP Firstly, you need to get the unit powered from the included injector and connect to with your computer. 1. Physically connect a network cable between the ubquiti device to the port labelled POE on the injector. 2. Physically connect a network cable between port labelled LAN on the injector and your Computer. 3. Set a Static IP on the Computer to (refer to the KBA Configuring a Static IP Address ) Page 1 of 13

2 4. Web Browse the unit on using chrome browser, chrome.google.com. 5. You will be presented with the below message on the first connection, select Advanced. 6. The following message with appear below advanced, Select Proceed. Page 2 of 13

3 7. Login using: o User: ubnt o Pass: ubnt 8. Select Australia and agree to the terms then select login. 9. Go to the Wireless Tab, start configuration. Page 3 of 13

4 10. Next, we will configure this as the Access Point which will be at Server/Panel/NVR end of the link(s). 11. The settings needed to set are the following 6 settings. o Wireless mode: Access Point o WDS: Enabled o SSID: csd-m5-link (needs to be unique to the site but the same across all units) o Frequency, MHz: 5740 o Security: WPA2-AES o WPA Preshared Key: adecentpassword (needs to be unique to the site but the same across all units) Page 4 of 13

5 12. Select Change once you have input these 6 settings 13. You will then be prompted to change the login password for the device. o Preferably don t lose this password, you can reset it, but it will default the settings. 14. Next go to the network Tab (Do not click the Apply button yet) Page 5 of 13

6 16. On this Page we need to change the IP address to something other than the default. o IP address: Select change and then Select Apply. 18. Once You Select Apply is will display the below message o During this time the unit is rebooting and will be unreachable. o Page 6 of 13

7 19. Once it comes back it will redirect you the new IP (in this case ) o As it s a new IP address you will see this warning again. 20. Login to check the settings applied Page 7 of 13

8 21. Disconnect your PC from the LAN side of the injector. 22. Repeat Steps 1 to 9 with the next ubiquiti unit and its own separate injector. 23. Next, we will configure this second unit as the Station which will be at Camera/CLOE/Edge devices end of the link(s). 24. The settings needed to set are the following 5 settings: o Wireless mode: Station o WDS: Enabled o SSID: csd-m5-link (needs to be unique to the site but the same across all units) o Security: WPA2-AES o WPA Preshared Key: adecentpassword (needs to be unique to the site but the same across all units) Page 8 of 13

9 25. Select Change once you have input these 5 settings 26. You will then be prompted to change the login password for the device. o Preferably don t lose this password, you can reset it, but it will default the settings. 27. Next go to the network Tab (Do not click the Apply button yet) Page 9 of 13

10 29. On this Page we need to change the IP address to something other than the default. o IP address: (if it s not the first station it would be 202 for the 2nd and 203 for the 3rd) 30. Select change and then Select Apply. 31. Once You Select Apply is will display the below message o During this time the unit is rebooting and will be unreachable. o Page 10 of 13

11 32. Once it comes back it will redirect you the new IP (in this case ) o As it s a new IP address you will see this warning again. 33. Login to check the settings applied Page 11 of 13

12 34. The back of the units will also show signal strength lights once connected. 35. Additionally, you can web browse the Access point and see the connected stations. Page 12 of 13

13 36. If this is just a Point to Point link consisting of two ubiquiti units, you are done. Point to Multipoint Setup 37. If you have more than one station and you have a Point to Multipoint system. o In this case for each additional station you repeat steps 21 to 35. o Only thing to keep in mind is when you come to step 29 make sure you use a unique IP. (e.g. if it s not the first station it would be.202 for the 2nd and.203 for the 3rd) Page 13 of 13