IDM1xx Bluetooth Hand-held Scanners

Transcription

1 MING MANUAL IDMxx Bluetooth Hand-held canners Hand-held Line

2 Revision History Rev. No. Released Date Description Rev. A Jan., First Release Rev. A Mar., Rev.A Jun., Modify UPC-E/EAN-8 expansion and UPC-A standardization. Add Presentation ensitivity. Add Extremely short option to Good Read Duration. Add UPC/EAN ecurity Level. Baud Rate Add 57.6K BP and 5.K BP. Add Immediate parameter for "Time Delay to Low Power Trigger" and change the default value from 5 sections to immediate. Hands Free Time out Add Disable. Rev. A ep, Add upplement can Voting in ymbology Reading Control Add EAN upplement Control Keyboard Layout Add Czech (QWERTY), remove Universal, and rename pain (QWERTY) to pain (panish QWERTY), Latin America (QWERTY) to pain (Latin America, QWERTY) Add Good Read Indicator Add can Rate Control Add canned Data Field Delimiter Quantity parameter selection on Batch Data Quantity Output Format. Rev. A4 Nov, Baud Rate Cancel Baud Rate /6 BP. Rev. A5 Jan 5, Buzzer Tone Adjust Modify No power-on beep behavior. The setting of No power-on beep will impact both Bluetooth canner and mart Cradle. Add Beeping Control setting. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice

3 Revision History Rev. No. Released Date Description Rev. A6 Mar 4, Baud Rate Revise 57.6K BP and 5.K BP option code from 6.7. to 8.9. Rev. A7 Mar 7, Rev. A8 Jun 7, Add Code 9 ecurity Level Add NAK Retry Count Add ACK/NAK Transmission Indication Introduction of IDM6 Bluetooth UCC/EAN-8 was renamed G-8. Add new parameter selections to ACK/NAK Transmission Indication. Add new parameter selections to erial Response Time-out. Add Laser Aiming Control Add Numeric Bar Codes Rev. A9 Aug, Paging/ Reset button is changed from seconds to 5 seconds. Rev. A July 5, General Update ICK makes no warranty of any kind with regard to this publication, including, but not limited to, the implied warranty of merchantability and fitness for any particular purpose. ICK shall not be liable for errors contained herein or for incidental consequential damages in connection with the furnishing, performance, or use of this publication. This publication contains proprietary information that is protected by copyright. All rights are reserved. No part of this publication may be photocopied, reproduced or translated into any language, in any forms, in an electronic retrieval system or otherwise, without prior written permission of ICK. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice

4 Warranty The currently released status of ICK General Terms of Delivery Factory Automation and Logistics Automation shall apply Regulatory FCC, CE, CN, LP, MIC LED Eye afety IEC647- LED Class Roh All Bluetooth IDM devices are conform to Roh standards Print out this manual If you want to print out this manual please ensure that the original size is remained and the print out is of good quality. Otherwise the configuration codes contained in this manual may be distorted and cannot be scanned anymore. Deutsche Version / German version Das Handbuch ist auch in deutscher prache verfügbar. Es kann unter heruntergeladen werden. This manual is available in German language as well. You can download it on /WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 4

5 Getting tarted Table of Contents Getting Familiar with Your IDM BT 5 Preparation before Using 7 Decide Your Radio Link Mode 9 Using IDM BT in PAIR Mode Using IDM BT in PICO Mode Using IDM BT in HID Mode Using IDM BT in PP Mode 4 Out-of-range canning/presentation canning/paging Function 6 Batch canning (Inventory Mode) 7 Configure Your IDM Bar Code Programming Manual 9 Programming Procedures Host Interface election 4 ymbology Reading Control 5 Keyboard Interface Control 45 erial Interface Control 49 Wand/Laser Emulation Control 5 Operation Control 54 Condensed DataWizard 65 Appendix ymbology ID Table 7 Keyboard Function Code Table 7 ACII Input hortcut 74 Link Mode Quick et/operation Mode Quick et 75 Host Interface Quick et 76 Option Codes 77 ystem Commands 8 How to connect IDM BT scanner with configuration software IDM et Up Tool 8 Indications /WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 5

6 Getting tarted Getting Familiar with Your IDM BT Thank you for choosing ICK canners. All canners deliver reliable performance for a broad range of market applications to unleash your productivity IDM4BT eries canner IDM6BT eries canner tatus Indicator Trigger Tether Plate Link Indicator Battery Cavity Lanyard Catch Beeper End Cap Retaining crew can Window Reset Button IDM4BT mart Cradle 8456/WE95/-7-5 IDM6-BT mart Cradle Center Indicator Host Interface Port ide Indicators DC Power Jack Paging/Reset Button Upper Indicator UB Bus Power witch Lower Indicator ICK AG Germany All rights reserved ubject to change without notice 6

7 Getting tarted IDM4BT Charging Cradle IDM6-BT Charging Cradle Power Indicator Host Interface Port Reserved DC Power Jack UB Bus Power witch 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 7

8 Getting tarted Preparation before Using Install the Battery Ensure the battery contacts of the battery pack are facing the charging contacts inside the battery cavity. lide the battery pack into the battery cavity until hearing a click sound before locking it with the end cap. The scanner will give 4 beeps when the battery pack is installed properly if the battery pack still has power. ecure the end cap with the screw provided. You can use the overlapping battery label to pull out the battery if needed. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 8

9 Getting tarted Charge the Battery!! Please always ensure that you are using a battery with enough capacity. Otherwise it might happen that the scanner loses its radio connection!! Take care that the unit is placed properly inside the respective base or charging station. When unit is not placed properly, the charging is not guaranteed. IDM4BT: IDM6BT: Insert scanner vertically First insert backside of scanner and then top part In every case you can verify the charging status via the LED on the scanner top (see also LED indications table inside appendix of this manual) 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 9

10 Getting tarted General Procedure Plug the AC power plug into the appropriate AC wall socket. Plug the DC power cord of the power supply unit into the DC power jack of the cradle. The cradle will issue the power on beeps. The center (upper) indicator of smart cradle will give one blue blink. The power indicator of charging cradle will turn steady blue. Place the scanner on the cradle. The status indicator of scanner will turn steady red if the battery is not fully charged. When the battery is fully charged, the status indicator of scanner will flash green at regular interval. Please charge the new battery pack for 8 hours prior to the first use. Use UB Bus Power If UB. is available in your host device, both battery charging and regular operation can be supported by the UB Bus Power without using external power supply. If you want to use this feature, please slide the UB bus power switch to ON. Then connect the cradle and host device via UB cable. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice

11 Getting tarted Communication Cables Both the IDM4BT and the IDM6BT offer P/, UB and R interface. UB The cable inlet of both IDM4BT and IDM6BT base station is on the bottom side. Please ensure that the cable is correctly pushed into the RJ inlet of the base station to secure data transmission to the host IDM4BT base station IDM6BT base station: Push down plastic spring and insert cable Correct Not Correct 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice

12 Getting tarted Decide Your Radio Link Mode The image scanner provides several radio link modes to communicate with most host devices. When the Bluetooth-enabled host device is not available, it can work with the smart cradle in PAIR mode (one to one connection) or PICO mode (multiple connections) to provide a plug-and-play cordless migration of your existing non-bluetooth-enabled IT assets. Moreover, you are also able to use the scanner to work with Bluetooth-enabled host devices via PP master/slave modes and HID mode. After losing the radio link, the scanner is capable of resuming the radio connection automatically while it returns to the communication coverage. But please note that this feature is not available in PP slave mode. If you would like to change the radio link mode, you have to scan the Uninstall command to revert the scanner to uninstall state. PAIR Mode scanner connected to one cradle If the Bluetooth device is not available in your existing system, this is the simplest plug-and-play solution. In this mode, one scanner can only work with one smart cradle. The smart cradle not only provides the Bluetooth radio link with the scanner, but also offers the legacy cabled interfaces to the host device, including UB HID, UB COM, P/(DO/V) Keyboard Wedge and R erial. PICO Mode up to 7 scanners connected to one cradle For the requirement of multiple connections, up to 7 scanners can be connected to one smart cradle concurrently. If you would like to un-pair all paired scanners and smart cradle, you can simply press and hold the paging/reset button of the smart cradle for over 5 seconds. If you just want to un-pair part of the paired scanners, please take those paired scanners to scan the Uninstall command one by one. HID Mode HID communication directly to Bluetooth host without cradle Through the most helpful HID service, the scanner can work like a Bluetooth keyboard. In this mode, the scanner is discoverable by the radio connection request issued by a remote host device. For security purpose, you will be requested to input the PIN Code to establish the Bluetooth connection in most time. PP Master/lave Mode erial communication directly to Bluetooth host without cradle Through the standard PP service, the scanner can work like a serial input device. In PP master mode, the scanner initiates the radio connection request to a remote slave device. In PP slave mode, the scanner is discoverable by the radio connection request issued by a remote master device. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice

13 Getting tarted Using IDM BT in PAIR Mode Ensure the battery is fully charged. You may refer to the section of Preparations before Using for details. Please choose your desired interface cable, then plug it into the host interface port of the smart cradle and connect it to the host device. UB P/ R Turn on the power of your host device. Please note that the scanner has been pre-paired already, if the scanner is shipped together with the smart cradle. You will see the link indicator of scanner gives blue blink per.5 seconds and the middle indicator of smart cradle turns steady blue. If the scanner and smart cradle just give alternating red and green blinks (in Uninstall state), please follow steps 5-6 to establish the connection between the scanner and the smart cradle. can PAIR mode command. The status indicator of scanner will turn steady red. Uninstall PAIR Mode Place the scanner on the smart cradle, then you will hear one short beep to indicate the pairing process is activated. The scanner will give continuous short clicks and the link indicator of scanner will flash blue quickly during the pairing process. When you hear 4 beeps in ascending tone, the pairing process is completed. You will see the link indicator of scanner giving blue blink per.5 seconds and the center or upper indicator of the smart cradle turning steady blue. If the scanner pairing process failed or it s not placed on the smart cradle within seconds, you will hear Di-do Di-do beeps to indicate pair failure, the scanner will return to uninstall state automatically. can the corresponding host interface quick set command to complete the installation. The default host interface of smart cradle is preset to UB HID. If you want to set the host interface to UB COM, you have to install the UB virtual COM driver (available on into your host device before using the scanner. General selection of host interface can be made via chapter Host Interface election. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice

14 Getting tarted Using IDM BT in PICO Mode Ensure the battery is fully charged and choose your desired interface cable, then plug it into the host interface port of the smart cradle and connect it to the host device. UB P/ R Turn on the power of your host device. Ensure the side (IDM4BT cradle) or lower indicator (IDM6BT cradle) of the smart cradle give alternative red and green blinks (in Uninstall state). If the smart cradle is paired with other scanners, you can press and hold the paging/reset button for over 5 seconds to un-pair all paired scanners. Then smart cradle will return to uninstall state automatically. Prepare the scanners you desire to pair with smart cradle. Ensure the status indicator of each scanner give alternative red and green blinks (in Uninstall state). If the scanner is not in uninstall state, please scan the Uninstall command to un-pair the scanner. Then scan the PICO mode command, and the status indicator of scanner will turn steady red. Uninstall PICO Mode Place the scanner on the smart cradle, then you will hear one short beep to indicate the pairing process is activated. The scanner will give continuous short clicks and the link indicator of scanner will flash blue quickly during the pairing process. When you hear 4 beeps in ascending tone, the pairing process is completed. You will see the link indicator of scanner giving blue blink per.5 seconds, the center or upper indicator of the smart cradle turning steady blue and its side indicators turning steady green. If the scanner pairing process failed or it s not placed on the smart cradle within seconds, you will hear Di-do Di-do beeps to indicate pair failure, the scanner will return to uninstall state automatically. can the corresponding host interface quick set command to complete the installation. Please follow the same procedures to pair the other scanners with the smart cradle. For user s convenience, the smart cradle will automatically assign the ID numbers to each scanner. After completed all pairing processes, you can scan the ystem Information command to check the assigned ID number of each scanner. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 4

15 Getting tarted Clone Function For the user s convenience, the clone function will help you to clone the host interface related parameters (please refer to following table for details) from one of the paired scanners to the rest of paired scanners under PICO mode. You can use one of the paired scanners to set the host interface related parameters first and then scan ave Configuration command. After that, please take the other paired scanners to scan Clone command one by one to clone the host interface related parameters. Please ensure to keep those paired scanners in connected status when you use the Clone function. Because the host interfaces related parameters can t be cloned to the paired scanner in disconnected status. ave Configuration Clone The below host interface related parameters will be impacted by clone function: Data Transmission Parameter Field Delimiter Data Transmission Format erial Interface Control Handshaking Protocol Intermessage Delay Host Interface Control Host interface election Keyboard Interface Control Keyboard Layout Intermessage Delay Interfunction Delay Intercharacter Delay Caps Lock Control Caps Lock Release Control Function Key Emulation Key Pad Emulation Upper/Lower Case Interfunction Delay Intercharacter Delay Baud Rate Data Frame Time Out Control Wand Emulation Control Output Polarity Initial ignal tate Margin Time Module Time Narrow/Wide Ratio Code9 Emulation 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 5

16 Getting tarted Using IDM BT in HID Mode Ensure the battery is fully charged. Power on the scanner within radio range and ensure the status indicator of scanner gives alternating red and green blinks (in Uninstall state). If the scanner is not in uninstall state, please scan the Uninstall command first. Then scan the HID Mode command, and the link indicator of scanner will give blue blinks per seconds. Uninstall HID Mode Execute the Bluetooth Discovery procedure to find all available Bluetooth devices in your remote host. You will see IDMxxxBT-xxxx is shown in the list if the scanner is successfully discovered already. Double click the IDMxxxBT-xxxx in the discovered Bluetooth device list. If the PIN Code or Passkey is requested for security connection, please enter (default setting). You will see Keyboard on IDMxxxBT-xxxx, and double click this HID service to establish the connection between the scanner and the remote host device. The scanner will give 4 beeps in ascending tone to indicate the radio is connected. At the same time, the link indicator of scanner will give blue blink per.5 seconds to indicate the scanner is in radio-connected state. Please note that if the scanner is not connected to the host device within minute after scanning the HID Mode command, the scanner will go to sleep automatically. You just need to press the trigger to wake up the scanner to continue the installation.. The installation procedures vary on different remote host devices, operation systems and the Bluetooth software driver. Please consult your professional IT consultant to obtain necessary support if any problem has been encountered during the installation processes.. While using HID mode, beware of potential error in the data transmitted at the same time when radio link quality is poor. You are suggested to use the scanner under the communication coverage all the times. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 6

17 Getting tarted Using IDM BT in PP Mode Establish PP Master Connection Ensure the battery is fully charged. Please go to the folder of Hardware located in Bluetooth Advanced etting of the remote host device to check its device MAC address. Then prepare a -character Code 8 barcode of the remote host device MAC address, or follow the step 4 to input MAC address by scanning option codes. Ensure a virtual COM port is available in your remote host for connecting the scanner. If not, please go to the folder of Local ervices located in Bluetooth Advanced etting. Click the Add erial ervices to add one more Bluetooth COM port. Power on the scanner within radio range and ensure the status indicator of scanner gives alternating red and green blinks (in Uninstall state). If the scanner is not in uninstall state, please scan the Uninstall command first. Then scan the PP Master Mode command, and the status indicator of scanner will turn steady red. Uninstall PP Master Mode can a -character MAC address barcode, or scan option codes and command to confirm your inputs. The scanner will give continuous short clicks and the link indicator of the scanner will flash blue quickly during the radio connecting process. If the PIN Code or Passkey is requested for security connection, please enter (default setting). The scanner will give 4 beeps in ascending tone to indicate the radio is connected. At the same time, the link indicator of scanner will give blue blink per.5 seconds to indicate the scanner is in radio-connected state. Please note that if the scanner failed to connect to the host device within seconds, the link indicator will give blue blinks per seconds. But the scanner is still continuing to discover the host device for another seconds before go to sleep. In the interim, you still can scan Uninstall command to revert the scanner to uninstall state. If the scanner goes to sleep already, you just need to press the trigger to wake up the scanner to continue the installation. The installation procedures vary on different remote host devices, operating systems and the Bluetooth software driver. Please consult your professional IT consultant to obtain necessary support if any problem has been encountered during the installation processes. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 7

18 Getting tarted Establish PP lave Connection Ensure the battery is fully charged and a virtual COM port is available in your remote host for connecting the scanner. If not, please go to the folder of Client Applications located in Bluetooth Advanced etting. Click the Add COM Port to add one more Bluetooth COM port. Power on the scanner within radio range and ensure the status indicator of scanner gives alternating red and green blinks (in Uninstall state). If the scanner is not in uninstall state, please scan the Uninstall command first. Then scan the PP lave Mode command, and the link indicator of scanner will give blue blinks per seconds. Uninstall PP lave Mode Execute the Bluetooth Discovery procedure to find all available Bluetooth device list in your remote host. You will see IDMxxxBT-xxxx is shown in the list if the scanner is successfully discovered already. Double click the IDMxxxBT-xxxx on the discovered Bluetooth devices. If the PIN Code or Passkey is requested for security connection, please enter (default setting). You will see erial Port on IDMxxxBT-xxxx, and double click this PP service to establish the connection between the scanner and the remote host device. The scanner will give 4 beeps in ascending tone to indicate the radio is connected. At the same time, the link indicator of scanner will give blue blink per.5 seconds to indicate the scanner is in radio-connected state. Please note that if the scanner is not connected to the host device within minute, the scanner will go to sleep. You can press the trigger to wake up the scanner to continue the installation. The installation procedures vary on different remote host devices, operating systems and the Bluetooth software drivers. Please consult your professional IT consultant to obtain necessary support if any problem has been encountered during the installation processes. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 8

19 Getting tarted Out-of-range canning When the radio is connected between the scanner and the remote host device, the scanner will transmit each scanned data right after scanning the barcode. However, the scanner is preset for unable to scan any barcode data when it loses the radio connection with the remote host device. If you enable the out-of-range scanning function, the scanner is able to continue scanning barcode data while it is out of working range. All scanned data will be temporarily stored into the memory buffer until radio link resumed. Enable Out-of-range cannning Disable Out-of-range canning In case of the scanner is out of working range, you will hear 4 beeps in descending tone to indicate the radio connection lost. The link indicator of scanner will give blue blinks per seconds. Once the scanner is back to working range, you will hear 4 beeps in ascending tone to indicate the radio connection rebuilt and the scanner will give blue blink per.5 seconds. At the same time, all stored scanned data will be transmitted automatically right after the radio link is resumed. Presentation canning The Presentation canning is designed for hand-free applications for user s convenience. If the Presentation canning Auto-sense function is enabled, the scanner is capable of automatically switching to presentation mode when you place it onto the tand or cradle. Presentation scanning on cradle is only available for IDM4BT. Paging Function Enable Presentation canning Auto-sense Disable Presentation canning Auto-sense The paging function is helpful for you to locate the paired smart cradle or scanner. If you would like to page the paired smart cradle, you can scan Paging command. If you would like to page the paired scanner, you can press the paging/rest button of the smart cradle no longer than 5 seconds. Paging 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 9

20 Getting tarted Batch canning (Inventory Mode) Thanks to the specially designed Batch canning function, the scanner is capable of storing the barcode data up to, EAN- labels. It is an ideal cost-saving solution for inventory applications. Once you scan the Enter Batch canning command to activate this function, all scanned barcode data will be stored into the memory storage, and the status indicator of scanner will give green blink at regular interval during batch scanning. You can scan and store the barcode data till the memory storage is full. If the storage is full, you will hear long beeps and the status indicator will give red blinks to indicate out of storage. To terminate the batch scanning, please scan the Exit Batch canning command. How to Transmit tored Data Enter Batch canning Exit Batching canning The scanner is preset so you need to scan the Transmit tored Data command to transmit all stored data. During the transmission process, the scanner will give continuous short clicks and blue blinks. Then the scanner will give two short beeps after data transmission is completed. Transmit tored Data But you are also able to set the scanner to transmit the stored data by placing the scanner onto the cradle. Transmit tored Data by canning Barcode Command Transmit tored Data by Placing canner onto Cradle Transmit tored Data by canning Barcode or Placing canner onto Cradle The scanner is preset to keep all the stored data until you scan the Clear All tored Data command. But you are also able to change the setting to Auto Delete tored Data after Transmission. Clear All tored Data 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice

21 Getting tarted Auto Delete tored Data after Transmission Keep tored Data after Transmission If you scanned a wrong barcode, the Delete Last canned Data command is helpful to recover mistake. By scanning the Delete Last canned Data command, the last stored data can be deleted. Using Quantity Feature Delete Last canned Data If you want to input the quantity information of barcode data, you can enter the quantity from to 9999 by scanning the quantity barcodes right after you scanned the barcode data. The quantity information will be stored into the memory storage together with the barcode data. Quantity Quantity 5 Quantity Quantity 8 Quantity Quantity 6 Quantity 4 Quantity 9 Quantity Quantity 7 There are two ways to output the stored barcode data and quantity information. Please refer to following for details: tored data is transmitted as many times as the quantity indicated (default). tored data is transmitted together with quantity information in two fields. Please scan Enable Quantity Field Transmission command to enable this function. The preset delimiter is,, but you are able to choose your desired one via using configuration codes inside chapter Operation Control. Disable Quantity Field Transmission Enable Quantity Field Transmission 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice

22 Bar Code Programming Manual The IDM BT bar code commands are specially designed Proprietary bar code labels which allow you to set the IDM BT internal programming parameters. There are ystem Command, Family Code and Option Code for programming purpose. Each programmable family and bar code command label is listed on the same page with major system commands. The detailed explanations and special programming flowchart are printed on facing or following pages. You can read the explanation and set the IDM BT concurrently. ystem Command The ystem Command is the highest level bar code command which directs IDM BT to perform immediate operations, such as entering programming mode (), exiting programming mode (EXIT), listing system information (YLIT), recovering to factory preset configurations (M_DEFAULT), and so on. Please note that all system commands will take a few seconds to complete the operations. User must wait for the completion beeps before scanning another bar code. A supplemental bar code command menu incorporates the bar code command labels of ystem Command and Option Code. As you set the IDM, open the bar code command menu to find the option code page. You may scan the desired family code and option code to set IDM. If you want to change the programming family for multiple settings, you need only turn over the programming page to find next desired programming family. Family Code The Family Code is scanned to select the user desired programming family. IDM BT has already provided more than one hundred programming families to meet any specific requirements. Option Code The Option Codes is a set of bar code commands represented by 9, A F and finishing selection (). For most setting, you must select at least one option code following the family code selection to set the desired parameter for the selected programming family. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice

23 Programming Procedures As you scan the bar code command to select the desired parameters, information about the final selected parameters represented by the bar code commands are stored in the IDM s internal Flash Memory AIC or non-volatile memory. If you turn off the unit, the Flash Memory AIC or non-volatile memory retains all programming options. You need not re-program the IDM BT if you want to keep the existing configurations in the next power on. The programming procedures of IDM BT are designed as simple as possible for ease of setting. Most programming families take the ingle can election programming procedure. But several programming families have more complex and flexible programmable options, and you must take Multiple cans election, Cycling can election or Dual Level election to complete their programming procedures. Each kind of programming procedure is listed in the following pages for your reference. Please give careful attention to become familiar with each programming procedure. If the programming family must take multiple scans selection, cycling scan selection, or dual level selection procedures, the family of the programming menu will be marked with the matched representing symbol of Programming Category (P.C.) in bold font listed in the following table. You can easily find the bold mark in the programming menu, and refer to their flowcharts for details. Before setting the IDM, please also refer to the Beeping Indications listed in Appendix to understand the details of programming beeping indications. It will be very helpful for you to know the existing status while you are programming the IDM. Conventions of Programming Menu Conventions Descriptions Factory Default Value P.C. Programming Category : ingle scan selection M : Multiple scans selection C : Cycling scan selection D : Dual level scan selection ( ) Necessary Option Code [ ] electable Option Code 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice

24 Program & End ystem List, Group & Master Default can can YLIT IDM will enter programming mode, and inhibit all non-programming functions. IDM will list the product information and revision number to host via selected host interface, then issue the completion beeping. can END can M_DEFAULT IDM will exit programming mode, and store all parameters in Flash Memory AIC or non-volatile memory, then issue the completion beeping. IDM will recover all programmable parameters into factory preset configurations, then issue the completion beeping. Please note that the IDM BT will take -4 seconds to store parameters in internal Flash Memory AIC or non-volatile memory after you scan the END. Please don t turn off the power before the completion beeping. It may destroy all configured parameters. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 4

25 ingle scan selection Multiple scans selection can Enter programming mode. can Enter programming mode. can One of Family Codes elect one of desired programming families. can One of Family Codes elect one of desired programming families. can One of Option Codes elect one option code of desired parameter. can One or everal Option Codes. elect one or several option codes to select desired parameters.. If it s necessary, scan Yes Repeat election No can END Want to select another programming family? Exit programming mode. Yes Repeat election No can END to terminate option code selection. Want to select another programming family? Exit programming mode. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 5

26 Cycling scan selection Dual level selection can Enter programming mode. can Enter programming mode. can One of Family Codes elect one of desired programming families. can One of Family Codes elect one of desired programming families. can One of Option Codes can Cycling select one or several option codes of desired parameters as ingle or Multiple scans selection. (st) can everal Option Codes (nd) can One or everal Option Codes elect several option codes of desired parameters.. elect one or several option codes of desired parameters.. If it s necessary, scan Yes Repeat election No can END Finish cycling selection. (If necessary) Want to select another programming family? Exit programming mode. Yes Repeat election No can END to terminate option code selection. Want to select another programming family? Exit programming mode. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 6

27 Host Interface election Family Code election P.C Parameter election Option Code Host Interface election M M M M M M M M M M IBM P/, 5- series keyboard wedge interface tandard/ttl R- peer-to-peer serial Wand emulation UB Com Port Emulation P/ (DO/V) direct link (keyboard replacement) P/ (DO/V) keyboard wedge turbo mode P/ (DO/V) keyboard wedge standard mode Laser emulation UB HID standard mode UB HID turbo mode Please note: When using UB mode, field disturbances in frequency ranges of 6 MHz +/- MHz MHz +/- MHz 48 MHz +/- MHz 64 MHz +/- MHz to 5 MHz can reduce the immunity of IDM6BT. This is only valid while using UB mode. After a possible disturbance, the scanner automatically re-connects with its base station. Codes that were scanned in the meantime are stored in the internal scanner memory. After the radio connection is re-established, buffered codes will be automatically transmitted to the host. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 7

28 ymbology Reading Control User Defined ymbol ID Family Code election P.C Parameter election Option Code nd Option Code ymbol ID : character D Code 8 (default=b) G-8 (default=c) UPC-A (default=a) EAN- (default=f) Codabar/NW-7 (default=d) Code 9/Code (default=g) Code 9 (default=h) tandard/industrial of 5 (default=i) Interleaved of 5 (default=j) Matrix of 5 (default=k) China Postal Code (default=l) German Postal Code (default=m) IATA (default=o) Code (default=p) MI/Plessey (default=r) UK/Plessey (default=) Telepen (default=t) G DataBar (default=x) UPC-E (default=e) EAN-8 (default=n) Trioptic Code 9 (Default=W) UCC Coupon Extended Code (Default=Z) PDF47/Micro PDF47 (default=v) Codablock F (default=y) Korea Post Code (default =a) If your application requires user defined symbology IDs you are able to configure it ( character) ( character) ( character) ( character) ( character) ( character) ( character) ( character) ( character) ( character) ( character) ( character) ( character) ( character) ( character) ( character) ( character) ( character) ( character) ( character) ( character) ( character) ( character) ( character) ( character) 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 8

29 ymbology Reading Control ymbology ID Transmission Family Code election P.C Parameter election Option Code ymbology ID Transmission Disable symbology ID transmission Enable prefix user defined symbology ID transmission Enable suffix user defined symbology ID transmission Enable both prefix and suffix user defined symbology ID transmission Enable prefix AIM symbology ID transmission Enable suffix AIM symbology ID transmission Enable both prefix and suffix AIM symbology ID transmission /WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 9

30 ymbology Reading Control Readable Bar Code etting Family Code election P.C Parameter election Option Code Readable ymbology etting C C C C C C C C C C C C C C C C C C C C C C C Auto Code 8 * UPC-A * UPC-E * EAN- * EAN-8 * Codabar/NW-7 * Code 9 * Trioptic Code 9 tandard/industrial of 5 Matrix of 5 Interleaved of 5 * China Postal Code German Postal Code Code 9 * Code MI/Plessey UK/Plessey Telepen G DataBar (R-4) * IATA PDF47/Micro PDF47 Codablock F Korea Post Code If your application is known, you may select those known symbologies only to increase the reading speed and decrease the possibility of reading error. Furthermore, to add the ymbology ID into the transmitted data is also helpful to identify the specific symbology. Above symbologies marketed with * are enable as default. When you select Auto, the scanner only read those symbologies marked with * When you set the minimum and maximum length of each symbology, please note the data length of scanned bar code doesn t include star/stop characters /WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice

31 ymbology Reading Control Code 9/Code etting Family Code election P.C Parameter election Option Code Code 9 Family etting Trioptic Code 9 etting Code 9 Min. Length Code 9 Max. Length M M Disable Code 9 Enable Code 9 elect tandard Code 9 as primary format elect Full ACII Code 9 as primary format elect Code (PARAF, Italian Pharmaceutical) as primary format Disable start/stop symbol transmission Enable start/stop symbol transmission Disable Code leading A transmission Enable Code leading A transmission Disable MOD 4 check digit verification Enable MOD 4 check digit verification Disable check digit transmission Enable check digit transmission Disable Code 9 buffering Enable Code 9 buffering Disable Trioptic Code 9 Enable Trioptic Code 9 Default () -Maximum can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. Default (98) 98-Minimum Trioptic Code 9 and Code 9 Full ACII cannot be enabled simultaneously. can digits from the option code chart in Appendix, then IDMBT will terminate this selection automatically A B C D E ( digits) ( digits) 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice

32 ymbology Reading Control Code 9 etting Family Code election P.C Parameter election Option Code Code 9 ecurity Level Level Level Level Level 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice

33 ymbology Reading Control Codabar/NW-7 etting Family Code election P.C Parameter election Option Code Codabar etting Codabar Min. Length Codabar Max. Length M M Disable Codabar Enable Codabar elect Codabar standard format elect Codabar ABC format elect Codabar CLI format elect Codabar CX format Disable start/stop symbol transmission Enable ABCD/ABCD start/stop symbol transmission Enable abcd/abcd start/stop symbol transmission Enable ABCD/TN*E start/stop symbol transmission Enable abcd/tn*e start/stop symbol transmission Disable check digit verification Enable check digit verification Disable check digit transmission Enable check digit transmission Default (4) -Maximum can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. Default (98) 98-Minimum can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically A B C D E ( digits) ( digits) 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice

34 ymbology Reading Control UPC-A & UPC-E etting Family Code election P.C Parameter election Option Code UPC Family etting Disable UPC-A Enable UPC-A Disable UPC-E Enable UPC-E Disable UPC-E expansion Enable UPC-E expansion Disable UPC standardization Enable UPC standardization Disable UPC numeric system Enable UPC numeric system Disable UPC-A check digit transmission Enable UPC-A check digit transmission Disable UPC-E check digit transmission Enable UPC-E check digit transmission Disable UPC leading portion Enable UPC leading portion When enable UPC-E expansion, the UPC-E decoded data will be converted to UPC-A format and affected by related setting, such as UPC standardization, UPC numeric system, UPC-A check digit transmission. UPC-E & EAN-8 Expansion : Expand the 8-digit UPC-E and 8-digit ENA-8 to -digit UPC-A and -digit EAN-. UPC-A/E tandardization : Expand the -digit UPC-A to -digit EAN- with zero insertion. UPC Lead Numeric ystem : Enable to read UPC leading with the numeric system, you must enable this option. WPC election (UPC/EAN/CAN) Basic Length Disable Check Digit Disable Numeric ystem With -digit Addendum With 5-digit Addendum Enable tandardization A B C D E F Enable Expansion UPC-A UPC-E EAN- - NC NC EAN NC NC /WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 4

35 ymbology Reading Control UPC-A & UPC-E etting Family Code election P.C Parameter election Option Code UPC upplement etting elect UPC without supplement digits elect UPC with only supplement digits elect UPC with only 5 supplement digits elect UPC with /5 supplement digits Disable force supplement digits output Enable force supplement digits output UPC Family Addenda eparator Off UPC Family Addenda eparator On UPC/EAN ecurity Level Level Level Level upplement can Voting Only available for UPC-A & EAN- None Level Level Level Level 4 Level 5 Level 6 Level 7 Level 8 Level 9 Level Level Level Level UPC/EAN ecurity Level The scanner offers three levels of decode security for UPC/EAN bar codes: Level : If you are experiencing misread of poorly-printed or out-of-spec. bar codes, especially in characters,, 7, and 8 in level, please select level. election of this security level may significantly impair the decoding ability of the scanner. Level : This is the default setting which allows the scanner to operate fastest, while providing sufficient security in decoding in-spec UPC/EAN bar codes. Level : If you are experiencing misread of poorly-printed, soiled or damage bar codes in level, please select level. This is the most aggressive setting and may increase the misread. The upplement can Voting is the number of times the same UPC/EAN with /5 supplement digits has to be decoded before it is transmitted. It is helpful when decoding a mix of UPC/EAN symbols with and without supplement digits. This function is effective when you select UPC/EAN with only supplement digits, UPC/EAN with only 5 supplement digits or UPC/EAN with /5 supplement digits. The default value is Level. When you select higher level, it may impact the reading speed on poorly-printed, low contrast or damage barcode labels A B C D 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 5

36 ymbology Reading Control EAN etting Family Code election P.C Parameter election Option Code EAN etting Disable EAN- Enable EAN- Disable EAN-8 Enable EAN-8 Disable EAN-8 expansion Enable EAN-8 expansion Disable EAN- check digit transmission Enable EAN- check digit transmission Disable EAN-8 check digit transmission Enable EAN-8 check digit transmission Disable IBN/IN Conversion reading check Enable IBN/IN Conversion reading check A B EAN upplement etting upplement can Voting elect EAN without supplement digits elect EAN with only supplement digits elect EAN with only 5 supplement digits elect EAN with /5 supplement digits Disable force supplement digits output Enable force supplement digits output EAN Addenda eparator Off EAN Addenda eparator On None Level Level Level Level 4 Level 5 Level 6 Level 7 Level 8 Level 9 Level Level Level Level The upplement can Voting is the number of times the same UPC/EAN with /5 supplement digits has to be decoded before it is transmitted. It is helpful when decoding a mix of UPC/EAN symbols with and without supplement digits. This function is effective when you select UPC/EAN with only supplement digits, UPC/EAN with only 5 supplement digits or UPC/EAN with /5 supplement digits. The default value is Level. When you select higher level, it may impact the reading speed on poorly-printed, low contrast or damage barcode labels A B C D 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 6

37 ymbology Reading Control UPC/EAN ecurity Level etting Family Code election P.C Parameter election Option Code UPC/EAN ecurity Level Level Level Level Only available for UPC-A & EAN- EAN upplement Control Disable all specific prefix supplement digital output Enable all specific prefix supplement digital output Enable 49 upplement Digit Output Enable 978/979 upplement Digit Output Enable 977 upplement Digit Output Enable 78/79 upplement Digit Output Enable 44/49 upplement Digit Output Enable 44/49 upplement Digit Output UPC/EAN ecurity Level The scanner offers three levels of decode security for UPC/EAN bar codes: Level : If you are experiencing misread of poorly-printed or out-of-spec. bar codes, especially in characters,, 7, and 8 in level, please select level. election of this security level may significantly impair the decoding ability of the scanner. Level : This is the default setting which allows the scanner to operate fastest, while providing sufficient security in decoding in-spec UPC/EAN bar codes. Level : If you are experiencing misread of poorly-printed, soiled or damage bar codes in level, please select level. This is the most aggressive setting and may increase the misread /WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 7

38 ymbology Reading Control UCC Coupon Extended Code etting Family Code election P.C Parameter election Option Code UCC Coupon Extended Code Disable UCC Coupon Extended Code Enable UCC Coupon Extended Code UCC Coupon Extended Code When UCC coupon extended code function is enabled, scanner decodes UPC-A barcodes starting with digit 5, EAN- barcodes starting with digit 99, and G-8 Coupon Codes. UPC-A, EAN- and EAN-8 must be enabled to scan all types of Coupon Codes. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 8

39 ymbology Reading Control IATA & Interleaved of 5 etting Family Code election P.C Parameter election Option Code IATA etting Disable IATA Enable IATA elect 5-digit fixed length IATA checking elect variable length IATA Disable check digit verification Enable check digit automatic verification Enable /N checking digit verification only Enable CPN checking digit verification only Enable CPN, Airline and /N check digit verification Disable check digit transmission Enable check digit transmission Disable start/stop symbol transmission Enable start/stop symbol transmission A B C Interleaved of 5 etting Disable Interleaved of 5 Enable Interleaved of 5 elect Interleaved of 5 as primary format elect German Postal Code as primary format No check character Validate U check digit Validate OPCC check digit Disable check digit transmission Enable check digit transmission /WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 9

40 ymbology Reading Control Code 5 Family etting Family Code election P.C Parameter election Option Code Code 5 etting Code 5 Family Min. Length Code 5 Family Max. Length M M Disable tandard/industrial of 5 Enable tandard/industrial of 5 Disable Matrix of 5 Enable Matrix of 5 Disable China Postal Code Enable China Postal Code Disable check digit verification Enable check digit verification Disable check digit transmission Enable check digit transmission Default (4) -Maximum can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. Default (98) 98-Minimum can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically ( digits) ( digits) For Code5 setting, we recommend you to select only one type of Code 5 or set the maximum/minimum bar code length. To decode all types of Code 5 or to variable length of Code 5 will increase the possibility of reading error. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 4

41 ymbology Reading Control Code & Code 9 etting Family Code election P.C Parameter election Option Code Code etting Disable Code Enable Code Disable check digit verification elect -check digit verification elect -check digit verification Disable check digit transmission Enable check digit transmission Code Min. Length M Default (4) -Maximum can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. ( digits) Code Max. Length Code 9 etting Code 9 Min. Length Code 9 Max. Length M M M Default (98) 98-Minimum can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. Disable Code 9 Enable Code 9 Disable check digit transmission Enable check digit transmission Default () -Maximum can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. Default (98) 98-Minimum can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. ( digits) ( digits) ( digits) 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 4

42 ymbology Reading Control MI/Plessey etting Family Code election P.C Parameter election Option Code MI/Plessey etting MI/Plessey Min. Length M Disable MI/Plessy Enable MI/Plessy elect MOD check digit elect MOD - check digit elect MOD - check digit Disable check digit transmission Enable check digit transmission Default (4) -Maximum can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically ( digits) MI/Plessey Max. Length M Default (98) 98-Minimum can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. ( digits) 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 4

43 ymbology Reading Control Code 8 & UCC/EAN 8 etting Family Code election P.C Parameter election Option Code Code 8/EAN-8 etting Disable Code 8 and G-8 Enable Code 8 and G-8 Disable function code conversion Enable function code conversion IBT Concatenation Off IBT Concatenation On 4 5 Code 8/EAN-8 Min. Length M Default () -Maximum can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. ( digits) Code 8/EAN-8 Max. Length M Default (98) 98-Minimum can digits from the option code chart in Appendix, then IDMBT will terminate this selection automatically. ( digits) 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 4

44 ymbology Reading Control UK/Plessey etting Family Code election P.C Parameter election Option Code UK/Plessey etting Disable UK/Plessey Enable UK/Plessey elect UK/Plessey tandard Format elect UK/Plessey CLI Format Disable Convert X to A-F Enable Convert X to A-F Disable check digit transmission Enable check digit transmission UK/Plessey Min. Length M Default (4) -Maximum can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. ( digits) UK/Plessey Max. Length M Default (98) 98-Minimum can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. ( digits) 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 44

45 ymbology Reading Control Telepen etting Family Code election P.C Parameter election Option Code Telepen etting Disable Telepen Enable Telepen elect Telepen Numeric mode elect Telepen Full ACII mode Disable check digit transmission Enable check digit transmission 4 5 Telepen Min. Length M Default (4) -Maximum can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. ( digits) Telepen Max. Length M Default (98) 98-Minimum can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. ( digits) 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 45

46 ymbology Reading Control G DataBar etting Family Code election P.C Parameter election Option Code G DataBar etting Disable G DataBar (R-4) Enable G DataBar (R-4) Disable G DataBar Limited Enable G DataBar Limited Disable G DataBar Expanded Enable G DataBar Expanded 4 5 G DataBar Min. Length M Default (4) -Maximum ( digits) Only available for Expanded G Databar. can digits from the option code chart in Appendix, then IDMBT will terminate this selection automatically. G DataBar Max. Length M Default (74) 74-Minimum Only available for Expanded G Databar. can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. ( digits) 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 46

47 ymbology Reading Control Linear-stacked & Korea Post Code etting Please note that stacked code only can be identified with IDMxxx PDF versions Family Code election P.C Parameter election Option Code Composite Codes etting Disable composite codes Enable composite codes UPC Composite Mode: UPC never linked UPC Composite Mode: UPC always linked PDF47/MicroPDF47 etting Disable PDF47 Enable PDF47 Disable MicroPDF47 Enable MicroPDF47 Codablock F etting Disable Enable Korea Post Code etting Disable Enable Length fixed in 6 characters. Composite Codes etting If UPC Composite Mode: UPC never linked is selected; UPC barcodes are transmitted regardless of whether a MicroPDF47 symbol is detected. If UPC Composite Mode: UPC always linked is selected, UPC barcodes are only transmitted when the MicroPDF47 is detected. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 47

48 Keyboard Interface Control Keyboard Layout (Language) etting Family Code election P.C Parameter election Option Code Keyboard Layout UA (QWERTY) France (AZERTY) Germany (QWERTZ) United Kingdom - UK (QWERTY) Canadian French (QWERTY) pain (panish, QWERTY) weden/finland (QWERTY) Portugal (QWERTY) Norway (QWERTY) pain (Latin America, QWERTY) Italy (QWERTY) Netherlands (QWERTY) Denmark (QWERTY) Belgium (AZERTY) witzerland-germany (QWERTY) Iceland (QWERTY) Japan (DO/V) Czech (QWERTY) Please refer to the ACII/HEX Table listed in the Appendix to determine HEX codes for characters, symbols, and functions to be used as preamble or postamble. To set preamble or postamble as function key output, you must enable the Function Key Emulation feature as listed in page -5 first. Keyboard Interface Message tring : Preamble Data Length Prefix ymbol ID canned Data uffix ymbol ID Postamble Record uffix -5 characters - digits or characters Variable length or characters -5 characters character /WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 48

49 Keyboard Interface Control Record uffix, Preamble, Postamble & Caps Lock Family Code election P.C Parameter election Option Code Record uffix None RETURN TAB PACE ENTER (Numeric Key Pad) User defined character ( character) 4 5, (-7F) Preamble M None -5 characters [-7F], [] Maximum 5-character input; scan to terminate this selection. Postamble M None -5 characters [-7F], [] Caps Lock Control Caps Lock Release Control Maximum 5-character input; scan to terminate this selection. Caps Lock Off tate Caps Lock On tate Auto Detect (PC/AT, P/, Keyboard Replacement and DO/V Machines only) Caps Lock On, Caps Off Caps Lock On, hift Off The function of Caps Lock Control and Key Pad Emulation are only available for IBM PC/AT, P/VP, P/ series personal computers and compatible machines. While selecting the other host interfaces, these selections don t perform the above functions for you. Please check the actual Caps Lock state in use while software application is running. If the Caps Lock state is off, select Caps Lock Off state, then IDM BT will perform normal data transmission. If the Caps Lock state is on, select Caps Lock On state. elect Auto Detect, IDM will perform special transmission handshaking without changing the status of Caps Lock switch. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 49

50 Keyboard Interface Control Delay etting Family Code election P.C Parameter election Option Code Intermessage Delay M None -99 (x) msec. can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. ( digits) Intercharacter Delay M None -99 (x5) msec. ( digits) can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. Interfunction Delay M None -99 (x5) msec. ( digits) can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. Intermessage Delay is a time delay between messages output by IDM. Increasing this delay will help host applications process the incoming data on time. Intercharacter Delay is a time delay between data characters output by IDM. These two parameters are used to synchronize data communication when : ) the data transmission speed is too fast, characters may be skipped; ) multitasking operation system or host computers in a network may slow down the keyboard handling; ) various notebook or desktop PC systems require different timing parameter settings. Please always add one extra unit as safety margin when adjusting these two parameters. Interfunction Delay is a time delay between the transmission of each segment of the message string. Intermessage Delay, Intercharacter Delay and Interfunction Delay cannot be only worked under PP and HID modes. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 5

51 Keyboard Interface Control Emulation etting & Upper/Lower Case etting Family Code election P.C Parameter election Option Code Function Key Emulation Enable ACII - code as keyboard function code output Ctrl-Output Refer to Appendix Keyboard Function Code Table for details. Key Pad Emulation Disable key pad emulation Enable numeric output as key pad (Num Lock On) output Upper/Lower Case Normal case (neglect the upper/lower case control) Inverse case (change all characters output to inverse case) Upper case (force all characters output as upper case) Lower case (force all characters output as lower case) 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 5

52 erial Interface Control Record uffix, Preamble,Postamble etting Family Code election P.C Parameter election Option Code TX/ETX Control Disable TX/ETX transmission Enable TX/ETX transmission TX/ETX is two characters used to indicate the starting and ending of the total data frame transmitted via serial interface. Record uffix Preamble Postamble M M M erial Interface Message tring (R, UB COM) : None CR (DH) LF (AH) CRLF (DAH) TAB (9H) PACE (H) User defined character ( character) None -5 characters Maximum 5-character input; scan to terminate this selection. None -5 characters Maximum 5-character input; scan to terminate this selection , (-7F) [-7F], [] [-7F], [] TX Preamble Data Length Prefix ymbol ID canned Data uffix ymbol ID Postamble ETX Record uffix character -5 characters - digits or characters Variable length or characters -5 characters character character 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 5

53 erial Interface Control Delay etting Family Code election P.C Parameter election Option Code Intermessage Delay M None -99 (x) msec. can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. ( digits) Intercharacter Delay M None -99 (x5) msec. ( digits) can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. Interfunction Delay M None -99 (x5) msec. ( digits) can digits from the option code chart in Appendix, then IDM BT will terminate this selection automatically. Intermessage Delay is a time delay between messages output by IDM. Increasing this delay will help host applications process the incoming data on time. Intercharacter Delay is a time delay between data characters output by IDM. These two parameters are used to synchronize data communication when : ) the data transmission speed is too fast, characters may be skipped; ) multitasking operation system or host computers in a network may slow down the keyboard handling; ) various notebook or desktop PC systems require different timing parameter settings. Please always add one extra unit as safety margin when adjusting these two parameters. Interfunction Delay is a time delay between the transmissions of each segment of the message string. Intermessage Delay, Intercharacter Delay and Interfunction Delay cannot be only worked under PP and HID modes. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 5

54 erial Interface Control Protocol, Baud Rate, Data Frame, ACK/NAK etting Family Code election P.C Parameter election Option Code Handshaking Protocol None (free running mode) RT/CT (hardware handshaking) ACK/NAK (software handshaking) Xon/Xoff (software handshaking) NAK Retry Count times ~55 times ( digits) ACK/NAK Transmission Indication Disable Enable Disable ACK Indication Enable ACK Indication Baud Rate (BP) Data Frame 8.4K BP 9.K BP 96 BP 48 BP 8, None, 8, Odd, 8, Even, 8, pace, 8, Mark, 8, None, 7, Odd, 7, Even, 4 BP BP 57.6K BP 5.K BP 7, pace, 7, Mark, 7, None, 7, Odd, 7, Even, 7, pace, 7, Mark, A B C D E 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 54

55 erial Interface Control Time Out etting Family Code election P.C Parameter election Option Code erial Response Time-out None mseconds 5 mseconds 8 mseconds second seconds seconds 4 seconds 5 seconds 8 seconds seconds 5 seconds A B When the RT/CT Hardware Handshaking option is selected, the RT (request to send) and CT (clear to send) signals will be issued before normal data communication. This option is very helpful to ensure the reliability of data communication. When the ACK/NAK oftware Handshaking option is selected, the IDM BT waits for an ACK (acknowledge) or NAK (not acknowledge) from the host computer after each data transmission. If the NAK is received, IDM will re-send the data until receiving ACK. The erial Response Time-out is a pre-defined delay time for IDM BT to wait for handshaking, acknowledgment or non-acknowledgment from the host computer. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 55

56 Wand/Laser Emulation Control Output Polarity, ignal tate, Margin/Module Time, etc. Family Code election P.C Parameter election Option Code Output Polarity High level (5Vdc) on Bar (low level on pace) Low level (Vdc) on Bar (high level on pace) Determine the output voltage level for both bar and space. Initial ignal tate High Level (5Vdc) Low Level (Vdc) Determine the initial state of output voltage level. Margin Time msec. 5 msec. msec. 5 msec. msec. 5 msec. msec. Delay time before data transmission Module Time Narrow/Wide Ratio Code 9/Code 8 Emulation Extremely short hort Medium : :.5 : Disable standard Code 9 emulation Enable standard Code 9 skip emulation Enable standard Code 9 replace emulation Enable Full ACII Code 9 emulation Enable Code 8 emulation Long Time base of minimum narrow bar [ Code 9 kip ] : When this option is selected, all scanned data will be translated as tandard Code 9 wand/laser emulation output. If any lower case characters are read, they will be translated to upper case characters. Any other characters that are not available in Code 9 symbology set will be skipped. [ Code 9 Replace] : Any character not normally available in the standard Code 9 symbology set, will be translated as pace /WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 56

57 Operation Control Operation Mode Family Code election P.C Parameter election Option Code Operation Mode Trigger mode Presentation mode Trigger Mode (Low Power Triggering) The scanner goes into standby state after scanning the bar code. You must press the trigger to turn on the light source of the scanner before scanning the bar code. Presentation Mode (Auto Detection) Presentation mode uses ambient light to detect the bar codes. The light source is off until the scanner detects an image which is similar to a barcode. Then the light source turns on automatically to read the bar code. If the light level in the room is not high enough, Presentation Mode may not work properly. You can choose different level of Presentation ensitivity to meet your application (Please refer to the setting of Presentation ensitivity ). 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 57

58 Operation Control Buzzer, Indicator, Vibrator, Inverse Reading Family Code election P.C Parameter election Option Code Buzzer Tone Adjust Buzzer tone mute Buzzer tone low Buzzer tone medium Buzzer tone high Buzzer tone - extremely high Power-on beep No power-on beep Power On Indicator Disable (LED off) LED steady on LED flash Good Read Indicator Vibrator Control Inverse Reading Beeping Control Disable Enable Disable Enable Optional function, only available for vibrator model. Disable Enable Radio Connected/ Disconnected Beep On Radio Connected/ Disconnected Beep Off Battery Power Low Beep On Battery Power Low Beep Off 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 58

59 Operation Control Dollar ign Control, Redundancy, can Rate Control Family Code election P.C Parameter election Option Code Dollar ign Control Dollar sign output as $ Dollar sign output as Dollar sign output as Dollar sign output as Dollar sign output as 4 Redundancy None Level Level Level Level 4 Level 5 To prevent potential miss reading. 4 5 can Rate Control Dynamic Fixed The Redundancy is the number of times the same bar code label has to be decoded before it is transmitted. scanner before scanning the bar code. can Rate Control: The scanner will have better motion tolerance when you select Fixed scan rate. It s suitable for application which needs higher motion tolerance on the move. But this may impact to the reading distance. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 59

60 Operation Control Delay etting Family Code election P.C Parameter election Option Code Reread Delay (Double can Verification) Good Read Delay Disable Immediate time out hort time out Medium time out Long time out Force verification None msec. 5 msec. sec..5 sec. sec. sec. The Reread Delay (Double can Verification) is designed to inhibit IDM from reading the same bar code label twice in pre-defined short duration. Force Verification will not allow reading of the same bar code twice. This Good Read Delay is the minimum amount of time before the scanner can read another bar code /WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 6

61 Operation Control Time-out etting, Good Read Duration Family Code election P.C Parameter election Option Code Light ource On Time hort Medium Long Extremely long Hands Free Time-out hort Medium Long Extremely long Disable 4 Good Read Duration Time Delay to Low Power Trigger hort Medium Long Extremely long Extremely short sec secs 5 secs 7 secs 9 secs Immediate The Light ource On Time is a pre-defined light source time out counter for Alternative Mode, Presentation Mode and Level Mode. The scanner keeps the light source on till the pre-defined light source on time is up. You can adjust this parameter to meet your own application requirement. The Presentation Mode is referred to as hands free mode. The hands free mode will be automatically changed to manual trigger mode when you press the trigger. You can remain the scanner in manual trigger mode by setting the Hands Free Time-Out. Once the time-out duration is up (if there s no any trigger operation), the imager will revert to the original hands free mode. The Time Delay to Low Power Trigger sets the time for scanner to enter low power trigger mode after any scanning activity /WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 6

62 Operation Control Presentation canning etting, Laser Aiming Control Family Code election P.C Parameter election Option Code tand Power Off Timeout mins 5 mins mins Only available for ICK IDM Laser model Presentation Auto-sense Disable Enable Presentation ensitivity Laser Aiming Control Level Level Level Level 4 Level 5 Disable Enable Level 6 Level 7 Only relevant for models with integrated laser aimer. The tand Power Off Timeout is a pre-defined duration for scanner s light source on time when the scanner is placed on tand. While the scanner is placed on tand, the scanner s will be switched from hand-held scanning to presentation scanning and the light source will be forced on automatically. The light source will be off when the pre-defined duration is up. When enable the Presentation Auto-sense, the scanner can be switched between hands free scanning and hand-held scanning automatically when working with the tand or cradle The Presentation ensitivity is used to configure the sensitivity level when the scanner is set as presentation mode. The higher lever means higher sensitivity for detecting the barcode /WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 6

63 Operation Control Out-of-range canning, leep Time-out Control Family Code election P.C Parameter election Option Code Out-of-range canning Disable Enable Link upervision Time-out sec secs 5 secs 7 secs 9 secs 4 Only available in PAIR & PICO modes leep Time-out of Connect tate leep Time-out of Disconnect tate M M 6 (x5) minutes -99 (x5) minutes minute -99 minutes ( digits) ( digits) Out-of-range canning when radio link is built between the scanner and remote host device, the scanner will transmit each scanned data right after scanning the barcode data. However, the scanner is preset for unable to scan any barcode data when it loses the radio connection. You can enable the Out-of-range canning function to continue scanning barcode data into memory buffer until radio link resumed. The Link upervision Time-out is a pre-defined radio link supervision timeout setting. The scanner will supervise the radio link status every preset seconds. The leep Time-out Control can be set under radio connection or disconnection state. If the scanner is not used within the preset time-out duration, it will automatically enter leep tate for power saving purpose. You are able to disable this function by setting the time-out duration to. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 6

64 Operation Control Batch canning etting Family Code election P.C Parameter election Option Code Batch canning Link Control Radio disable Radio enable tored Data Transmission All On cradle can barcode Delete tored Data after Transmission Disable Enable The Batch canning Link Control is a pre-defined radio option to control the radio-on or radio-off status under batch scanning operation. Please note that if the radio disable is activated, the radio link will be disconnected once you enter batching scanning. The radio link will be resumed when you transmit the stored data or exit batch scanning. The tored Data Transmission is a pre-defined approach when you want to transmit the scanned data under batch scanning operation. You can transmit the scanned data by placing the scanner onto the cradle or scanning Transmit tored Data command, or by either one of both methods. In batching scanning, the default setting of Delete tored Data after Transmission is disabling. The scanner will keep all stored data after transmission until you scan the Clear All tored Data command. You are also able to delete all stored data after transmission automatically by enabling this function. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 64

65 Operation Control Batch canning Data Transmission etting Family Code election P.C Parameter election Option Code Field Delimiter None, PACE. User define 4 5, [-7F] Batch Data Quantity Output Format As many times as the quantity indicates <Quantity><Field Delimiter><canned Data> <canned Data><Field Delimiter><Quantity> Data Transmission Format Disable (scanned data only) Leading with MAC address (MAC address and scanned data) Leading with ID No. (scanner ID and scanned data) Only available for R, UB HID and UB COM interface in PAIR & PICO modes The Field Delimiter is used to separate the specific information and scanned data into two fields. You can choose desired delimiter format. The Batch Data Quantity Output Format If you want to input the quantity information of barcode data, you can enter the quantity from to 9999 by scanning the quantity barcodes right after you scanned the barcode data. The quantity information will be stored into the memory storage together with the barcode data. There are two ways to output the stored barcode data and quantity information. In PICO mode, up to 7 scanners can be connected with one smart cradle. The Data Transmission Format can help user to identify the source of the transmitted data. You can choose to transmit the scanned data leading with MAC address or pre-assigned ID. Example format: <MAC address><field Delimiter><Data> or <ID><Field Delimiter><Data>. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 65

66 Operation Control Bluetooth Device Name & ecurity etting Family Code election P.C Parameter election Option Code Bluetooth Device Name M Default device name User define, -6 characters [-7F], Bluetooth PIN Code M Default Bluetooth PIN Code User define, -8 numbers [-9], Bluetooth Authentication Disable Enable The default Bluetooth Device Name is IDMxxxBT--xxxx, you will be able to change the device name by scanning HEX values (-6 characters). The default Bluetooth PIN Code is, you will be able to change the PIN Code by scanning HEX values (-8 numbers). The Bluetooth Authentication You can enable or disable the Bluetooth Authentication between the scanner and remote host device. If this function is enabled, when the scanner wants to connect itself and sends the data to the host device, the host device has to return a link key shared between the scanner and the host device. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 66

67 Operation Control Bluetooth Other ettings Family Code election P.C Parameter election Option Code HID Link Quality etting Disable Enable Bluetooth Power aving Mode Disable Enable The HID Link Quality etting while using the HID radio link mode, some errors may occur during the data transmission when the radio link is disconnected. You can enable this function to prevent such error from occurring. The Bluetooth Power aving Mode Bluetooth module will enter low consumption mode when you enable this function. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 67

68 Condensed DataWizard Preamble, Postamble, Data Length & ymbol ID Trans. Family Code election P.C Parameter election Option Code Preamble M None -5 characters [-7F], [] Maximum 5-character input; scan to terminate this selection. Postamble M None -5 characters [-7F], [] Maximum 5-character input; scan to terminate this selection. Data Length Transmission Disable Enable digits data length transmission If data length exceeds 99, -digit data length will be transmitted. ymbology ID Transmission Disable symbology ID transmission Enable prefix symbology ID transmission Enable suffix symbology ID transmission Enable both prefix and suffix symbology ID transmission Enable prefix AIM symbology ID transmission Enable suffix AIM symbology ID transmission Enable both prefix and suffix AIM symbology ID transmission DataWizard is the most powerful, Artificial-Intelligence based data editing expert system provided specially for the IDM BT family bar code readers. Through DataWizard, you can process the scanned data prior the transmissions in many ways as: Insert, Delete, Match, Verify, Replace, Reorganize, and Repeat Transmission. It will help you to arrange the transmission of scanned data to any specific format without software modification. Due to the resources used by this system, Full-feature DataWizard is only supported by IDM et Up Tool. Through the IDM et Up Tool, all settings and configurations can be done on-screen, under Windows 95/98/NT//XP environment. A Condensed Version DataWizard is provided by each IDM series. Through this menu, the condensed DataWizard can be utilized via bar code menu readings with ease. Please note that all Character input should be referred to the ACII/HEX Table listed in Appendix to find matched HEX value. If you have any problem to use DataWizard, please refer to following pages for details and consult your local IDM BT vendor or our web site for any assistance /WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 68

69 Condensed DataWizard Data Formatter etting Family Code election P.C Parameter election Option Code nd Option Code Formatter Control M M Disable elect one bar code symbology elect all bar code symbologies ( digits) automatic termination automatic termination st Insertion D Disable Enable ( digits) [- characters], [] -digits identified position; max. insertion characters position nd Insertion D Disable Enable ( digits) [- characters], [] rd Insertion 4th Insertion D D -digits identified position; max. insertion characters Disable Enable -digits identified position; max. insertion characters Disable Enable -digits identified position; max. insertion characters position ( digits) position ( digits) position [- characters], [] [- characters], [] The Data Formatter is used to edit the scanned raw data prior to transmitting the data to the host computers or terminals. It allows you to select desired bar code symbologies for formatter control, and provides Multiple Position Insertion and Multiple Character Insertion (max three characters) in the identified position. While the Data Formatter is enabled, it arranges only scanned data without Preamble, Postamble, TX, ETX, Data Length, Prefix/uffix ymbolology ID or Record uffix. All of the above programmable parameters perform the same function depending on your setting. Regarding the Bar Code election and Position Calculation of data formatter, please refer to page 65 for details. Please note that all Character input should be referred to the ACII/HEX Table listed in Appendix to find matched HEX value. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 69

70 Condensed DataWizard Data Verifier etting Family Code election P.C Parameter election Option Code nd Option Code Verifier Control M M Disable elect one bar code symbology elect all bar code symbologies ( digits) automatic termination automatic termination Identified Data Length M Disable Enable ( digits) Determine the identified data length for verification. st Identified Character D Disable Enable ( digits) [-7F] -digits checking position; identified character position nd Identified Character rd Identified Character D D Disable Enable -digits checking position; identified character Disable Enable -digits checking position; identified character ( digits) position ( digits) The Data Verifier is used to provide advanced verification for error-free scanning and to work as an Embedded Data Transmitting Filter. All data must conform to the Identified Bar Code ymbologies, Identified Data Length, and one to three Identified Characters in the checking position. Otherwise, the IDM BT will not transmit the data to the host computers or terminals, but will instead issue long beeps for verification error and skip the scanned data. The Data Verifier checks only scanned data without Preamble, Postamble, TX, ETX, Data Length, Prefix/uffix ymbology ID or Record uffix. Regarding the Bar Code election and Position Calculation of Data Verifier, please refer to page 65 for details. Please note that all Character input should be referred to the ACII/HEX Table listed in Appendix to find matched HEX value. position [-7F] [-7F] 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 7

71 Condensed DataWizard Data Replacer etting Family Code election P.C Parameter election Option Code nd Option Code Replacer Control M M Disable elect one bar code symbology elect all bar code symbologies ( digits) automatic termination automatic termination st Replacement D Disable Enable ( digits) [-7F] -digits identified position; replacement character position nd Replacement D Disable Enable ( digits) [-7F] -digits identified position; replacement character position rd Replacement D Disable Enable -digits identified position; replacement character ( digits) The Data Replacer is used to edit the scanned raw data prior to transmitting the data to the host computers or terminals. It allows you to select desired bar code symbologies for replacer control, and provides Multiple Position Replcement in the identified position. All data must conform to the Identified Bar Code ymbologies, and one to three Identified Characters in the identified position while the Data Replacer is enabled; it arranges only scanned data without Preamble, Postamble, TX, ETX, Data Length, Prefix/uffix ymbology ID or Record uffix. Regarding the Bar Code election and Position Calculation of Data Replacer, please refer to page 65 for details. Please note that all Character input should be referred to the ACII/HEX Table listed in Appendix to find mathced HEX value. position [-7F] 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 7

72 Condensed DataWizard Data Organizer etting Family Code election P.C Parameter election Option Code nd Option Code Organizer Control M M Disable elect one bar code symbology elect all bar code symbologies ( digits) automatic termination automatic termination st Organization D Disable Enable -digits identified position; Forward/backward data transmission setting ( digits) position direction (Forward) (Backward) nd Organization D Disable Enable -digits identified position; Forward/backward data transmission setting ( digits) position direction (Forward) (Backward) Include/Exclude Control D Transmitted data excluded the data of identified position Transmitted data included the data of identified position The Data Organizer is used to edit the scanned raw data prior to transmitting the data to the host computers or terminals. It allows you to select desired bar code symbologies for organizer control, and provides maximum two identified positions to send the data forward or backward. It also allows you to control the transmitted data including or excluding the data of identification position. Please refer to the application example listed in page 65 for details. While the Data Organizer is enabled, it arranges only scanned data without Preamble, Postamble, TX, ETX, Data Length, Prefix/uffix ymbology ID or Record uffix. Regarding the Bar Code election and Position Calculation of Data Organizer, please refer to page 65 for details. Please note that all Character input should be referred to the ACII/HEX Table. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 7

73 elect a Bar Code ymbology You can select one or all types of bar code symbologies to use Condensed DataWizard for advanced transmission arrangement. If you scan to select all types, the IDM BT will arrange all incoming data to meet your pre-defined format. If you want to select only one type bar code, please select one of the option code listed below. Code 8 : UCC/EAN 8 : UPC-A : UPC-A with supple.: UPC-A with 5 supple.: 4 UPC-E : UPC-E with supple.: UPC-E with 5 supple.: 4 EAN- : 4 EAN- with supple. : 4 EAN- with 5 supple. : 44 EAN-8 : 5 EAN-8 with supple : 5 EAN-8 with 5 supple.: 45 Codabar/NW-7 : 6 Code 9 : 7 Code : 7 Trioptic Code 9: 47 Matrix of 5 : 8 Interleaved of 5 : 48 China Postal Code : 58 German Postal Code : 68 Code 9 : 9 Code : MI/Plessey : UK/Plessey : Telepen : G Data Bar : 4 IATA : 5 Coupon Code : 6 PDF47/MicroPDF47: Codablock: Korea Post Code: 6 Position Calculation [Data Formatter] Example: If there is a 5-character input data string, refer to the following to calculate the actual position for insertion: X X X X X 4 5 [Data Verifier, Data Replacer, Data Organizer] Example: If there is a -character data string, please refer to the following to calculate the actual position for identification. X X X X X X X X X X X Application Example If your bar code label is a 6-digit Interleaved of 5 which includes the information of 6-digit date code, 6-digit serial number and 4-digit unit price, you want the IDM BT do the following for you without software modification: Apply only Interleaved of 5 to the condensed DataWizard. Check bar code is actually with 6-digit length. Allow bar code output whose date code is leading with 9. Three outputs with TAB suffix. The date code output should skip 9 and replaced it by A. The serial number output should be led with N. The unit price output should be skipped the first digits. Test Bar Code : Actual Output : A85[TAB]N456[TAB]76[TAB] 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 7

74 Programming Procedure [Data Verifier] [Data Replacer] can Program to enter the programming mode. can Verifier Control and set bar code symbology to 48 (Interleaved of 5). can Identified Data Length and set the length to 6. can st Identified Character and set the identified position to, then set the identified character to 9 (Hex Code of 9). [Data Formatter] can Formatter Control and set bar code symbology to 48. can Replacer Control and set bar code symbology to 48. can st Replacement and set the identified position to, then replaced character to 4 (Hex Code of A). [Data Organizer] can Organizer Control and set bar code symbology to 48. can st Organization and set the identified position to 6, then set the data transmission to (forward). can st Insertion and set the identified position to 6, then inserted characters to 9 (Hex Code of TAB), 5 (Hex Code of ), 4E (Hex Code of N). can nd Insertion and set the identified position to, then inserted character to 9. In the final, you must scan (Finish) code to terminate this selection. can rd Insertion and set the identified position to 6, then inserted character to 9. In the final, you must scan (Finish) code to terminate this selection. can nd Organization and set the identified position to 7, then set the data transmission to (backward). can END (Exit) to terminate the programming. [Important Notice] Please note that Condensed DataWizard will follow the preset working flow as below: Verifier Formatter Replacer Organizer o when you set the identified position in Data Organizer, you must consider the inserted data which you already set via Data Formatter. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 74

75 ymbology ID Table Appendix Each AIM Code Identifier contains the three-character string ]cm where: ] = Flag Character c = Code Character m = Modifier Character The listed user defined characters are default values. User def. ID AIM ID User def. ID AIM ID Code Family Primary Format Code UPC Code 8 Character Code Character Modified Character Code Family Primary Format Code Character Code Character UPC-A m EAN/JAN-8 4 UPC-A with supple. A EAN/JAN-8 with supple. N E UPC-A with 5 supple. EAN/JAN-8 with 5 supple. E UPC-E m EAN/JAN- m EAN/JAN UPC-E with supple. E EAN/JAN- with supple. F E UPC-E with 5 supple. Example: A UPC-A bar code with supplement is transmitted as ]E ]E EAN/JAN- with 5 supple. Modified Character Example: A EAN/JAN-8 bar code 4956 with 5 supplement 45 is transmitted as ]E44956]E45 Code 8 B m Code 9 Code 9 H G m C G-8 C Code Code P H m Codabar Codabar/NW-7 D F m MI/Plessey MI/Plessey R M m Code 5 tandard/industrial of 5 I UK/Plessey UK/Plessey P Matrix of 5 K X Telepen Telepen T B m Interleaved of 5 J I m G DataBar G Databar China Postal Code L X Compsoite Composite Code X e Code 9 G A m German Postal Code M I Code 9 Code 9 Trioptic W X IATA IATA O R m UCC Coupon Code G A UCC Coupon Code Z PDF47 PDF47/Micro PDF47 V L Example : A UPC-A G bar code is transmitted as]e ]c84597 Example: A EAN G bar code is transmitted as ]E ]C84597 Codablock Codablock F Y O Korea Post Korea Post Code a X Remark: Above examples are given for the transmission of AIM ID. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 75

76 Appendix Keyboard Function Code Table No. ANI ACII Key Function No. ANI ACII Key Function NUL H REERVED 6 DLE H F7 OH H CTRL (Left) 7 DC H F8 TX H ALT (Left) 8 DC H F9 ETX H HIFT 9 DC H F 4 EOT 4H CAP LOCK DC4 4H F 5 ENQ 5H NUM LOCK NAK 5H F 6 ACK 6H EC YN 6H IN (Insert) (Edit) 7 BEL 7H F ETB 7H DEL (Delete) (Edit) 8 B 8H BACK PACE 4 CAN 8H HOME (Edit) 9 HT 9H TAB 5 EM 9H END (Edit) LF AH F 6 UB AH PAGE UP (Edit) VT BH F 7 EC BH PAGE DOWN (Edit) FF CH F4 8 F CH UP (Edit) CR DH ENTER (CR) 9 G DH DOWN (Edit) 4 O EH F5 R EH LEFT (Edit) 5 I FH F6 U FH RIGHT (Edit) To emulate the keyboard function key input for user definable parameters, user must configure actual content using the Reserved ACII characters, and also Enable the Function Key Emulation. Otherwise, the Ctrl output will be done by the scanner. Please refer to the above Keyboard Function Code Table which is for IBM PC/XT/AT, P/, P/VP, COMPAQ PC, HP Vectra PC, Notebook PC, APPLE and PowerMac, and WYE PC Enhanced or fully compatible machines. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 76

77 Appendix ACII Input hortcut To configure the user definable parameters of IDM BT via programming menu, IDM BT will ask you to scan your desired ACII value in HEX form. You have to refer to the HEX/ACII Table for details. Example: If you want the scanned data output leading with a Dollar ign, you have to set the Preamble to $. The configuration procedure is listed below for reference. can the system command listed on page -4 to enter programming mode. can family code PREAMBLE to select this family. Refer to the Hex/ACII Table, you will find the HEX value of $ is 4. HEX/ACII Reference Table H L NUL DLE P ` p OH DC! A Q a q TX DC " B R b r ETX DC # C c s 4 EOT DC4 $ 4 D T d t 5 ENQ NAK % 5 E U e u 6 ACK YN & 6 F V f v 7 BEL ETB ' 7 G W g w 8 B CAN ( 8 H X h x 9 HT EM ) 9 I Y i y A LF UB * : J Z j z can the option code listed on the fold out back cover. can the option code 4 listed on the fold out back cover. can the system command (Finish) to terminate Preamble setting. can the system command End to exit the programming mode for normal operation. B VT EC + ; K [ k { C FF F, < L \ l D CR G - = M ] m } E O R. > N ^ n ~ F I U /? O _ o DEL Example: ACII A HEX 4 ; ACII a 6 : High Byte of HEX Value : Low Byte of HEX Value 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 77

78 Link Mode Quick et Appendix Uninstall PP lave Mode PAIR Mode HID Mode PP Master Mode PICO Mode Operation Mode Quick et Trigger Mode Presentation Mode 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 78

79 Appendix Host Interface Quick et (Work with mart Cradle only) R erial P/ (DO/V) KBW tandard Mode UB HID tandard Mode Keyboard Replacement P/ (DO/V) KBW Turbo Mode UB HID Turbo Mode UB COM recommendations UB Com Port Emulation (additional software driver needed, available on sick.com) If UB devices are not connected as UB HID (human interface device) but as VCP (virtual com port), Windows API does not control the connection and does not perform automatic re-connection in case of connection losses. Connection control management has to be realized within the application software which is using the com port as data input source (e.g. within driver access layer). 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 79

80 Option Codes Appendix 8 4 C 9 5 D A 6 E B 7 F (Finish) END (Exit) 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 8

81 ystem Commands Appendix (Enter Programming Mode) ave Configuration leep (Finish) Clone Paging END (Exit Programming Mode) Factory Default ystem Information List (YLIT) IDM et Up Link (connection procedure see next page) Master Default Factory Default: After scanning Factory Default command, all parameters will be returned to factory default value (The radio link will be disconnected and the scanner will revert to uninstall state). Master Default: After scanning Master Default command, the scanner will remain the pre-set parameters of Host Interface election, Keyboard Interface Control (except Record uffix; Preamble; Postamble), erial Interface Control (except Record uffix; Preamble; Postamble), Wand/Laser Emulation Control, Bluetooth Device Name, Bluetooth PIN Code & Out-of-range canning, the rest of parameters will be returned to default value (The radio link is still keep on). ave User Default User Default User Default: After configuring the IDM imager you can store your configuration via scanning ave User Default. When scanning User Default the scanner will load the configurations that you ve done before. Please note that when scanning Master or Factory Default the user default values will be deleted. 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 8

82 Appendix How to connect IDM BT canner with configuration software IDM et Up Tool The IDM et Up Tool is a windows based configuration software for IDM scanners. The following steps describe how to configure an scanner via this software tool. You can download the IDM et up software for free on Make sure, that the canner is paired with the base station (pair mode).. The interface has to be set to R or UB COM. You can test the communication with any terminal program. After testing close the terminal program so the com port is free again.. Please scan the Uninstall Code. Then scan the IDM et Up Link Code. It s important to place the scanner into its base station right now. 4. tart the IDM et Up Tool oftware and click on Upload. 5. Choose the right Communication Port. Afterwards click on the Upload button. The software will connect to the scanner and the Configuration Window opens. 6. Do your settings. 7. By clicking on the Apply button the download section opens. It s important that you scan the IDM set up link code again and place the scanner back inside the base again. 8. Click on the download button to start the download. After successful download you can close the IDM set up tool. 9. To re-connect scanner and base station, scan the pair mode code and place the scanner in the base station. IDM et Up Link Code 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 8

83 Indications Appendix Link Indicator tatus Indicator Descriptions Link Indicator Beeper Radio connected blue blink per.5 sec. Off Radio disconnected blue blinks per sec. Off During connection Quick blue blinks hort clicks Radio connection built blue blink per.5 sec. 4 beeps in ascending tone Radio connection lost blue blinks per sec. 4 beeps in descending tone Data Transmission Quick blue blink hort clicks Descriptions tatus Indicator Beeper Under charging (on cradle) teady red Off Fully charged (on cradle) green blink at regular interval Off Under batch scanning green blink per.5 sec. Off Pair failure teady red Di-do Di-do beeps Out of memory red blinks long beeps Battery power low red blink at regular interval beep at regular interval Battery power extremely low 8 red blinks 8 beeps Good read green blink good read beep Under Configuration teady red Off Uninstall state Alternative red and green blinks Off Upgrade state teady red hort click Time out warning Off long beeps Paged by smart cradle Off 6 page beeps leep state / Battery no power Off Off 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 8

84 Appendix Center (Power) Indicator ide Indicators Upper (Power) Indicator Lower indicator IDM BT Charging Cradle Indication Descriptions Power Beeper Power on teady blue Off IDM BT mart Cradle Indications Descriptions Indicators Center/Upper ide/lower Beeper Power on blue blink Off Power on beeps mart Cradle Upgrade tate Off teady red hort clicks Uninstall state Off Alternative red-green blinks Off PICO Mode Radio Connected teady blue teady Green Off Radio Disconnected Off teady red Off PAIR Mode Radio Connected teady blue Off Off Radio Disconnected Off teady red Off mart cradle paged PICO Mode teady blue teady green 6 page beeps by scanner PAIR Mode teady blue Off 6 page beeps 8456/WE95/-7-5 ICK AG Germany All rights reserved ubject to change without notice 84