PowerView Motorisation Smart shades that simplify your life

Transcription

1 PowerView Motorisation Smart shades that simplify your life Scene Quickstart guide The Art of Window Styling

2 A brilliant evolution in The Art of Window Styling.

3 This guide will help you get started with your PowerView purchase. STEP 1 INSTALL YOUR SHADES COMPONENTS Make sure you have properly installed your shades and that they are connected to a power source (battery pack or power supply). Wall Surface STEP 2 YOUR POWERVIEW COMPONENTS Pebble Remote Repeater (optional) Packed with your purchased product you will find one or more remotes, repeaters and a Hub (which is optional and only required when you want to control your shades using a tablet or smartphone). Remotes come in different shapes and colours. Please locate them all before you start. Hub (optional), required for controlling your shades with a tablet or smartphone. 3

4 PAIRING REMOTES STEP 3 PAIRING REMOTES If you only have one remote, please proceed to Step 4. By pairing PowerView remotes you make all your remotes part of the same PowerView Network. This is important for seamless installation of the PowerView system. Stop For this instruction you use the Remote. STOP button on your 3.1 TAKE ALL REMOTES. NAME 1 REMOTE SOURCE NAME THE REST OF THE REMOTES TARGET REPEAT THE FOLLOWING STEPS UNTIL ALL TARGET REMOTES HAVE BEEN SET. Source Target Target 4

5 TARGET REMOTE: 3.2 REMOVE BACK COVER (Keep batteries in place). PAIRING REMOTES TARGET REMOTE: 3.3 PRESS THE RESET BUTTON FOR SIX SECONDS The group button will flash on the press of the Reset button, then again at six seconds. 5

6 PAIRING REMOTES TARGET REMOTE: 3.4 CLOSE THE COVER SOURCE REMOTE 3.5 PRESS STOP FOR 6 SECONDS (Keep pressing until the remote lights start blinking). TARGET REMOTE: 3.6 PRESS STOP AND HOLD SOURCE REMOTE 3.7 PRESS STOP AND RELEASE TARGET REMOTE: 3.8 RELEASE STOP (As confirmation remote 2 will flash the group buttons). TARGET REMOTE: 3.9 IF THE BUTTONS ARE STILL FLASHING PRESS STOP FOR 6 SECONDS (Keep pressing until the flashing stops). 6

7 STEP 4 ADDING A SHADE TO A REMOTE A Remote can control 6 groups of shades (which are the buttons 1 to 6). The instructions below assign a shade to group 1. Depending on your preference you can choose your own group. This instruction will make use of the STOP buttons on your remote. OPEN, GROUP 1, and Open Group 1 Stop ADDING A SHADE TO A REMOTE Find the shade button on your shade. Different shade types have different shade buttons. Consult the shade documentation for the exact location of the shade button. Shade button 7

8 ADDING A SHADE TO A REMOTE 4.1 PRESS STOP FOR 6 SECONDS (Keep pressing until the remote lights start blinking). 4.2 PRESS GROUP1 (This will activate the group 1 on the remote). 4.3 PRESS AND HOLD THE SHADE BUTTON 4.4 PRESS THE OPEN BUTTON (You will see the shade move up and down shortly). 4.5 RELEASE THE SHADE BUTTON 4.6 IF YOUR REMOTE IS STILL FLASHING: PRESS STOP FOR 6 SECONDS AND HOLD (Keep pressing until the flashing stops). 8

9 STEP 5 INSTALL REPEATERS Installation of a repeater is necessary when your shade is not responding to a command from your remote control. Preferably put the repeater halfway between the unresponsive shade and the remote control location. Stop INSTALL REPEATERS This instruction will make use of the STOP button on your remote and the button on the repeater. Repeater button/light 9

10 INSTALL REPEATERS 5.1 PLACE THE REPEATER IN THE USB CHARGER AND PLUG IT IN AN OUTLET (The repeater light illuminates green). 5.2 PRESS STOP FOR 6 SECONDS AND HOLD (Keep pressing until the Remote lights start blinking). 5.3 HOLD THE REMOTE WITHIN 20 CM FROM THE REPEATER 5.4 PRESS STOP (The repeater light will turn off. The repeater is now part of your personal PowerView Network). 10

11 STEP 6 CONNECT AND SETUP THE HUB If you have not purchased a Hub please proceed to Additional Actions on page 15 to proceed with your installation. 6.1 CONNECT THE HUB TO YOUR HOME NETWORK ROUTER 6.2 CHECK THE RANGE OF THE HUB Your Hub should be able to reach each shade in the house. Use your remote from the same location as your Hub to operate your shades. If some shades do not respond, add or relocate a repeater and check again. CONNECT AND SETUP THE HUB 6.3 CONNECT THE HUB TO YOUR POWER OUTLET 11

12 CONNECT AND SETUP THE HUB 6.4 WAIT APPROX. 2 MINUTES AND OBSERVE THE HUB LIGHT - Blue/Red blinking: All ok. Proceed with the installation. - Red Blinking: Hub is downloading updates. Please wait (approx minutes). - Continuous blue: Hub is already connected to a network. If you have previously setup your hub you can continue. If not you can clear the data on the hub. Go to Erase hub data in the Additional actions chapter. 12

13 STEP 7 CONNECT THE POWERVIEW APP TO THE HUB Take your remote control. 7.1 DOWNLOAD THE POWERVIEW APP FROM THE APP STORE OR PLAY STORE 7.2 START THE APP (The app will start looking for an available Hub). 7.3 WAIT FOR THE FIRST SCREEN TO APPEAR AND CONNECT TO A HUB CONNECT THE POWERVIEW APP TO THE HUB 7.4 FOLLOW THE INSTRUCTIONS UNTIL YOU GET TO SCREEN 2 13

14 CONNECT THE POWERVIEW APP TO THE HUB 7.5 CHOOSE 1 REMOTE 7.6 FOLLOW THE ON SCREEN INSTRUCTIONS TO ADD THE HUB TO YOUR EXISTING POWERVIEW NETWORK 7.7 YOU CAN NOW START WITH THE APP (For further instructions please go to 14

15 ADDITIONAL ACTIONS Your PowerView Network is now setup and ready to be further adjusted to your preferences. Follow the steps in this chapter or go to for more information. OPERATE A SHADE This instruction will make use of the OPEN, GROUP 1, STOP, ALL and CLOSE buttons on your Remote. Open Group 1 Stop All Close ADDITIONAL ACTIONS 1 PRESS GROUP 1 (Group 1 will light up). 2 PRESS OPEN (Shades assigned to group 1 will open). 3 PRESS STOP (Shades assigned to group 1 will stop). 4 PRESS CLOSE (Shades assigned to group 1 will close). Pressing all instead of group 1 will move all shades from all 6 groups on the remote. 15

16 ADDITIONAL ACTIONS SET A FAVOURITE POSITION This instruction will make use of the STOP and FAVOURITE buttons on your remote. Stop Favourite Find the shade button on your shade. (Different shade types have different shade buttons. Consult the shade documentation for the exact location of the shade button). Shade button 16

17 1 MOVE YOUR SHADE TO THE DESIRED FAVORITE POSITION (Use your OPEN, CLOSE and STOP buttons to move the shade). 2 PRESS STOP FOR 6 SECONDS (Keep pressing until the Remote lights start blinking). 3 PRESS AND HOLD THE SHADE BUTTON ADDITIONAL ACTIONS 4 PRESS THE FAVOURITE BUTTON (You will see the shade move up and down briefly). 5 RELEASE THE SHADE BUTTON 6 IF YOUR REMOTE IS STILL FLASHING PRESS STOP FOR 6 SECONDS (Keep pressing until the flashing stops). 17

18 ADDITIONAL ACTIONS MOVE A SHADE TO A FAVOURITE POSITION This instruction will make use of the GROUP 1, and ALL button on the Remote. FAVOURITE Move shades assigned to group 1 to their favourite position. Group 1 Favourite All 1 PRESS GROUP 1 (Group 1 will light up). 2 PRESS FAVOURITE (Shades assigned to group 1 will move to their favourite position). Pressing all instead of group 1 will move all shades from all 6 groups to their favorite position. 18

19 REMOVE A SHADE FROM A GROUP This will remove a shade from a group on your remote control. It will not remove the shade from the PowerView network. This instruction will make use of the GROUP 1, CLOSE buttons on the Remote. STOP and Group 1 Stop Close ADDITIONAL ACTIONS Find the shade button on your shade. (Different shade types have different shade buttons. Consult the shade documentation for the exact location of the shade button). Shade button 19

20 ADDITIONAL ACTIONS The following instruction removes a product from group 1. 1 PRESS STOP FOR 6 SECONDS (Keep pressing until the remote lights start blinking). 2 BRIEFLY PRESS ON GROUP 1 (This will activate the group 1 on the remote). 3 PRESS AND HOLD THE SHADE BUTTON 4 BRIEFLY PRESS ON CLOSE (You will see the shade move up and down shortly). 5 RELEASE THE SHADE BUTTON 6 IF YOUR REMOTE IS STILL FLASHING PRESS STOP FOR 6 SECONDS (Keep pressing until the flashing stops). 20

21 INSTALL A SCENE CONTROLLER The Scene Controller works in combination with the App and can activate scenes which are created in the App. 1 START THE APP AND OPEN THE MENU 2 SELECT SCENE CONTROLLERS AND FOLLOW THE INSTRUCTIONS IN THE APP ADDITIONAL ACTIONS ERASE HUB DATA Find the following button on the back of the hub. 1 PRESS DATA ERASE FOR 6 SECONDS 2 WAIT FOR THE HUB TO START FLASHING RED AND BLUE All data on the hub is now cleared. Data erase 21

22 Smart design makes the difference.

23

24 A revolutionary new system that automatically moves your shades throughout the day, so you don t have to. All rights reserved. Unauthorised copying is prohibited. Technical data subject to change without notice. No rights can be derived from copy, text pertaining to illustrations or samples. Subject to changes in materials, parts, compositions, designs, versions, colours etc., even without notice. Registered trademark. A HunterDouglas product. Copyright HunterDouglas January 2017.