LP Series Label Feeders LPG01-001 Label Presenter Gem Product Guide All rights reserved Revision 5 23 Oct 09 0770D-E001
Product Guide Hover-Davis, Inc. has checked the contents of this printed document to verify that it is in agreement with the product described inside. However, discrepancies can and do occur. Therefore Hover-Davis, Inc. cannot assume responsibility for complete agreement between this printed document and the product described inside. The information contained in this document was thoroughly reviewed before going to print, and is subsequently reviewed and / or revised on a regular basis. Necessary corrections are included in future editions. We welcome any comments or suggestions for improvements. Technical Publications Copyright 2005-2009 by Hover-Davis. All rights reserved. If you need technical information or assistance with the installation of this product, please call our Customer Support Center 1-877-812-6830 Monday - Friday, 8:00am - 4:30pm, EST Email technical-support@hoverdavis.com 2005-2009 Hover-Davis, Inc. All rights reserved Revision 5 23 Oct 09 No. 0770D-E001
Table of Contents Raw Material Data (US and China)....ii Chapter One Tape Loading / Feeder Operation Installing and Removing the LMG Module...1-1 Tape Loading....1-2 Operation...1-6 Chapter Two Programming the Timeout Delay....2-1 Chapter Three LMG Module Timeout Delay Maintenance Troubleshooting....3-1 Preventive Maintenance...3-3 Drive Roller Disassembly...3-4 Controller Board Replacement...3-7 I/O Cable Replacement....3-9 Drive Motor Replacement...3-12 Control Panel Replacement...3-16 Chapter Four LPG01-001 Parts Lists Recommended Spare Parts...4-1 LPG01-001....4-2 191A-S74 Drive Assembly, 56mm.... 4-5 576A-S01 Module Interface...4-6 0610A-0005 Control Panel...4-7 i
Raw Material Data (US and China) Hazardous Substances or Elements Commodity Name Lead (Pb) Mercury (Hg) Cadmium (Cd) Chromium VI Compounds (Cr6+) Polybrominated Biphenyls (PBB) Chemicals X O O X X X Wiring/ Associated Components Polybrominated Diphenyl Ethers (PBDE) X O O O O O Metal X O X X O O Printed Circuit Boards X O O O O O Hardware X O O X O O Electrical Components (Purchased) X O O O O O O: this component does not contain this hazardous substance above the maximum concentration values in homogeneous materials specified in the SJ/Txxxx-xxxx Industry Standard. X: this component does contain this hazardous substance above the maximum concentration values in homogeneous materials specified in the SJ/Txxxx-xxxx Industry Standard (Company can explain the technical reasons for the "X"). (Pb) (Hg) (Cd) (Cr6+) (PBB) (PBDE) X O O X X X X O O O O O X O X X O O X O O O O O X O O X O O ( ) X O O O O O O: SJ/Txxxx-xxxx. X: SJ/Txxxx-xxxx. (, "X"..) ii
Chapter One Tape Loading Feeder Operation 1
Installing and Removing the LMG Module The LMG Module is a separate unit that works in conjunction with the LP Series label feeders. LMG Modules are interchangeable to allow easy changeover between different label stocks on the same feeder. Refer to the documentation provided with the LMG Module for more information. To install the LMG Module: 1. Pull the latch lever out on the LP Series Feeder and hold it in the out position (refer to Fig. 1-1). 2. Align the mounting pins on the bottom of the module with the mating holes on the module interface. 3. Push the LMG Module straight down until it seats flush on top of the module interface. LATCH LEVER ON LP SERIES FEEDER Fig. 1-1 4. Release the latch lever to lock the module in place (refer to Fig. 1-2). To remove the LMG Module: 1. Pull the latch lever out on the LP Series Feeder module interface. 2. Carefully pull the module straight up. 3. Release the latch lever. Fig. 1-2 Note If the LMG Module does not seat flush to the interface housing, carefully remove and inspect both the LMG Module and the top of the interface for dirt or other foreign materials that could prevent the LMG Module from seating properly. 1-1
Tape Loading Step 1 Install the label reel by placing it onto the Reel Holder at the Tail Section end of the feeder. Make sure the liner feeds from left to right out the top of the reel. Pull the liner from the reel in the direction shown. Fig. 1-3A Fig. 1-3B 1-2
Caution Before threading the liner through the Label Feeder, always remove enough labels from the lead end of the liner so it can be threaded through the LMG Module without having any labels pass through the lower part of the LMG Module. If labels are left on the liner, the hard turns of the liner path through the LMG Module will cause the labels to dislodge from the liner inside the unit, which can create potential feed problems. Step 2 Remove approximately 12 in. of labels from the lead end of the liner to thread the liner through the LMG Module. Insert the liner into the feeder by passing it under the first guide roller. Then thread the liner into the LMG module. GUIDE ROLLERS LMG MODULE NOTE: Complete tape path shown in illustration. Refer to following steps for details of tape loading. Fig. 1-4 1-3
Step 3 Press down the Peel Edge Pivot Lever on the LMG Module until the mechanism locks open. PEEL EDGE PIVOT LEVER Fig. 1-5 Note The LMG Module used for illustrations in this manual is fabricated with multiple rollers. However, each LMG Module is custom designed for a specific label and may have one or more rollers, one or more platforms, or a combination of rollers and platforms. Step 4 Feed the tape liner under the Tensioner and down between the Peel Edge and the first roller or platform of the LMG Module (refer to Fig. 1-6). TENSIONER PEEL EDGE ROLLERS Fig. 1-6 1-4
Note For proper alignment, the Drive Assembly Handle should be unlocked and remain in the unlocked position until all liner loading operations are complete. Step 5 Open the Drive Assembly by moving the handle into the vertical position, which will open the Rollers. Thread the liner under the guide roller and then between the open rollers on the Drive Assembly. Close the Drive Assembly Handle. The loading operation is now complete. HANDLE GUIDE ROLLER Fig. 1-7 1-5
Operation STATUS LIGHT FORWARD FEED CENTER BUTTON REVERSE FEED Control Functions STATUS LIGHT Flashing Red = Feeder not ready to run. It can be manually forward or reverse fed, but not run in automatic mode. Steady Green = Feeder Operational FORWARD FEED Press and hold to advance liner with labels until released. Fig. 1-8 CENTER BUTTON Press and release to auto-advance and recover from an error condition (flashing red). FIRST LABEL PEEL EDGE REVERSE FEED Press and hold to retract liner with labels until released. Operation Sequence Fig. 1-9 Fig. 1-10 FIRST LABEL CENTERED ON PICK POINT Power up the feeder with the Hover- Davis power supply or the pick and place machine. There will be a three second homing sequence. On startup, the feeder auto-advances the label to the Pick Point. When the label is in position, the Status Light changes to solid GREEN. Once the light is GREEN, the feeder is operational. The Status Light turns off during advance. Once a label is detected, the feeder stops advancing and the Status Light again turns GREEN. If a label is not detected by the end of the programmed time delay, the feeder stops advancing and the Status Light flashes RED. 1-6
Chapter Two LMG Module Timeout Delay 2
Programming the Timeout Delay Timeout Delay Chart YYYY Delay 0200 3 0300 3 0400 4 0500 5 0600 5 0700 6 0800 6 0900 7 1000 8 1100 8 1200 9 1300 10 1400 10 1500 11 1600 12 1700 12 1800 13 1900 13 2000 14 All label feeders have a timeout delay to make sure the feeder will advance the label to the Pick Point but will not continue advancing indefinitely if there are missing labels on the label stock. If the feeder reaches the programmed timeout delay before a label has reached the Pick Point, the feeder will resort to an error mode and will need to be reset by pressing the Center Button. This feeder timeout delay is programmable and should be set according to the specific label fed by the LMG Module being used. To set the timeout delay, find the model number located on the serial label of the LMG Module. Note the last four digits (YYYY) as shown below. LMG02-XXXXYYYY Using the chart to the left, match the last four digits of the LMG Module model number to the corresponding four digits on the chart. The number to the right of this is the corresponding offset that needs to be used to program the timeout delay. If the four digits do not appear on the chart, select the closest, next highest value. (For example, for a model number ending with 0728, use 0800 on the chart.) Note The Timeout Delay Chart assumes 0.125 in. [3mm] spacing between the consecutive labels on the liner. Label spacing of 0.25 in. [6mm] or greater requires adding (1) to the offset recommended on the chart. The maximum timeout offset delay that can be programmed is (20). 1. Power up the feeder either on the platform machine or an offline power supply. POWER SUPPLY TRIGGER BOX Fig. 2-3 2-1
2. Hold down the Center Button on the Control Panel until the Status Light turns Yellow. Release the button. The feeder is now in Program Mode. Fig. 2-4 3. Release the Center Button and count the number of times the Status Light blinks Green. The number of blinks equals the currently programmed Timeout Delay. Fig. 2-5 4. Press the Forward Feed button to increase the Timeout Delay (refer to Fig. 2-6) or press the Reverse Feed Button to decrease the Timeout Delay (refer to Fig. 2-7). Each press increases or decreases the delay by a count of one. Fig. 2-6 Fig. 2-7 2-2
1. Verify that the correct timeout has been set by pressing and releasing the center button and counting the number of times the Status light blinks green. The number of blinks equals the Timeout Delay. Fig. 2-8 5. When the Timeout Delay is correctly programmed, press and release the Forward Feed and Reverse Feed buttons simultaneously to exit programming mode. Fig. 2-9 2-3
Chapter Three Maintenance 3
Troubleshooting To inspect and repair the LP Series Label Presenter and LMG Label Module, follow the instructions listed in the chart on the following page. Warning Do not operate the feeder with the Covers removed. Caution When replacing parts and securing Covers, make sure all Cables are securely routed to avoid pinching and feeder damage. Caution When the feeder is loaded into the placement machine, the feeder MUST BE latched or locked into position. Caution Do not modify the feeder in any way 3-1
Feeder Condition No Power Error (Blinking red light on Control Panel LED) Cause Interface pins damaged Interface Cable pinched Damaged Controller Interface Cable not connected to controller Loose wire connection Incorrect label application Time Out Delay function set incorrectly for label length Feeder Loading Repair Solution (Possible Replacement Parts) Replace I/O cable Replace I/O cable Replace controller Plug connector into controller Replace damaged cable Verify compatible application for Label Module Verify Time Out Delay setting and reset as needed Verify the feeder is loaded correctly using the Tape Path Label on the feeder for reference. Make sure the drive system is closed (lever should be in the "down" position). Feeder Continually Advances Labels Pick Failure Label Module is not fully seated in Module Interface Adhesive buildup or Labels in drive system Adhesive build up on peel edge or Tensioner of Label Module Make sure Module is seated flush to the surface of the Inteface and that the lever is fully closed Clean drive system Clean Label Module Peel Edge and Tensioner Label Sensor damaged or Replace or calibrate Label Sensor misaligned Pinched or damaged motor Replace motor wires Broken or damaged O Ring Replace belt belt Label Sensor Wires pinched Replace Label Sensor Label Sensor calibration Verify Label Sensor is calibrated correctly Damaged Label sensor or wires Feeder pick point not on proper location Feeder not inserted fully Incorrect Feeder profile selection Replace Label Sensor Verify Label Sensor is calibrated correctly Make sure feeder is properly inserted onto machine feeder table Contact placement machine manufacturer for correct profile selection A custom pick point location may need to be set on machine depending on application or machine type Feeder Runs in Reverse Damaged Motor or Motor Wires Replace motor 3-2
Preventive Maintenance Note For proper operation, the preventive maintenance steps shown below should be performed at least every three months. Actual operating conditions may require more frequent cleaning. Note Refer to "Chapter 4 - Parts Lists" for exploded-view drawings showing the locations on each of the items described below. If replacement is required, refer to the appropriate procedure in the balance of this chapter. Drive Assembly Advance the feeder and examine the [191A-S75] Intermediate Gear as it rotates. If there is no lube present on the gear teeth, apply a small amount of Super Lube to the teeth of the gear as it rotates. Do not over lube the gear or allow lube to touch the drive pulleys as this may cause slippage in the drive system. (Refer to Drive Roller Disassembly procedures on Page 3-4.) Note Super Lube is a general purpose synthetic-based lubricant with Teflon available from Loctite Corp. (Item #82325). Label Roller(s)/Label Platform Inspect the roller(s)/platform for deposits of adhesive from the label backing. If found, wipe away with a clean, soft cloth. All Components Touching Tape Path Using a clean, soft cloth (or clean compressed air), wipe (blow) away any contamination from the tensioner, peel edge, drive pulleys, and dispenser drive. Drive Rollers Clean the drive rollers of any adhesive buildup. (Refer to Drive Roller Disassembly procedures on Page 3-4.) 3-3
Drive Roller Disassembly Warning Always disconnect all electrical power before working inside the feeder. Follow proper ESD (Electrostatic-discharge) procedures when handling electrical components inside the feeder. Use care when reinstalling covers to avoid pinching wires. Failure to heed these points may result in damage to the feeder or its electrical components.! Step 1 Remove the (2) M3 x 8 socket head cap screws and the (1) M3 x 5 socket head cap screw and M3 flat washer securing the Board Cover and remove the Board Cover. REMOVE Caution When replacing the Board Cover, be very careful not to pinch any of the cables that are routed beneath it. Fig. 3-1 Step 2 Remove the (2) stainless steel M3 x 6 socket button head screws and the [103C-106] MPF02 Board Stand securing the Controller Board. Label each of the cables attached to the Controller Board for accuracy at reassembly and disconnect the cables from the Controller Board. Remove the Controller Board. REMOVE Fig. 3-2 3-4
Step 3 Remove the (2) M3 x 5 socket flat head screws and (2) M3 x 30 stainless steel socket flat head screws securing the Motor Cover and remove the Motor Cover. REMOVE Fig. 3-3 Step 4 Open the Drive Lever to remove the tension between the Drive Roller and Idler Roller. Fig. 3-4 Step 5 Remove the E-clip from the end of the Drive Shaft. Remove the M3 x 30 socket button head screw securing the drive side plate. REMOVE Fig. 3-5 3-5
Step 6 Remove the Drive Side Plate and associated shafts and the Idler Retainer Assembly at the same time by drawing the assemblies directly away from the feeder. Fig. 3-6 Step 7 Remove the Drive Standoff, which is now free, so it does not fall off while the roller is being cleaned. Thoroughly clean the drive roller to remove any adhesive buildup. Fig. 3-7 Step 8 Separate the drive Side Plate and associated shafts and the Idler Retainer Assembly and thoroughly clean the Idler Roller to remove any adhesive buildup. Step 9 Fig. 3-8 Reverse Step 8 through Step 1 to reassemble. 3-6
Controller Board Replacement Warning Always disconnect all electrical power before working inside the feeder. Follow proper ESD (Electrostatic-discharge) procedures when handling electrical components inside the feeder. Use care when reinstalling covers to avoid pinching wires. Failure to heed these points may result in damage to the feeder or its electrical components.! Step 1 Remove the (2) M3 x 8 socket head cap screws and the (1) M3 x 5 socket head cap screw and M3 flat washer securing the Board Cover and remove the Board Cover. REMOVE Caution When replacing the Board Cover, be very careful not to pinch any of the cables that are routed beneath it. Fig. 3-9 Step 2 Remove the (2) stainless steel M3 x 6 socket button head screws and the [103C-106] MPF02 Board Stand securing the Controller Board. Label each of the cables attached to the Controller Board for accuracy at reassembly (refer to Fig. 3-11) and disconnect the cables from the Controller Board. Remove the Controller Board. Fig. 3-10 REMOVE Step 3 Reverse Step 2 through Step 1 to reassemble. 3-7
I/O CABLE MEMBRANE CABLE CONTROLLER BOARD Fig. 3-11 SENSOR CABLE DRIVE ASSEMBLY CABLE 3-8
I/O Cable Replacement Warning Always disconnect all electrical power before working inside the feeder. Follow proper ESD (Electrostatic-discharge) procedures when handling electrical components inside the feeder. Use care when reinstalling covers to avoid pinching wires. Failure to heed these points may result in damage to the feeder or its electrical components.! Step 1 Remove the (2) M3 x 8 socket head cap screws and the (1) M3 x 5 socket head cap screw and M3 flat washer securing the Board Cover and remove the Board Cover. REMOVE Caution When replacing the Board Cover, be very careful not to pinch any of the cables that are routed beneath it. Fig. 3-12 REMOVE Step 2 Turn the feeder over. While supporting the Interface Cable Mount, remove the (3) M3 x 8 socket flat head screws securing the Interface Cable Mount. Carefully remove the Interface Cable Mount making sure to not pull on the I/O Cable, which fits into the groove at the bottom of the mount. REMOVE Fig. 3-13 3-9
Step 3 Remove the (2) stainless steel M3 x 6 socket button head screws and the [103C-106] MPF02 Board Stand securing the Controller Board. REMOVE Fig. 3-14 Step 4 Carefully lift up slightly on the Controller Board to allow movement of the I/O cable past the standoff and disconnect the I/O Cable from the Controller Board. I/O CABLE MEMBRANE CABLE CONTROLLER BOARD Fig. 3-15 SENSOR CABLE DRIVE ASSEMBLY CABLE 3-10
Fig. 3-16 REMOVE Step 5 Attach the new I/O Cable to the controller board. Make sure the cable wires are routed to the right of the upper left standoff behind the Controller Board. Position the Controller Board over the standoffs. Insert and tighten the (2) stainless steel M3 x 6 socket button head screws and the [103C-106] MPF02 Board Stand to secure the Controller Board. Step 6 Capture the I/O Cable in the groove of the Interface Cable Mount as shown in Fig. 3-17, Align the Interface Cable Mount with the three mounting holes and, from the back side, insert and tighten the (3) M3 x 8 socket flat head screws that secure the Interface Cable Mount. Fig. 3-17 Step 7 Replace the Board Cover and secure by inserting and tightening the (2) M3 x 8 socket head cap screws and the (1) M3 x 5 socket head cap screw and M3 flat washer removed in Step 1. Fig. 3-18 Caution When replacing the Board Cover, be very careful not to pinch any of the cables that are routed beneath it. 3-11
Drive Motor Replacement Warning Always disconnect all electrical power before working inside the feeder. Follow proper ESD (Electrostatic-discharge) procedures when handling electrical components inside the feeder. Use care when reinstalling covers to avoid pinching wires. Failure to heed these points may result in damage to the feeder or its electrical components.! Step 1 Remove the (2) M3 x 8 socket head cap screws and the (1) M3 x 5 socket head cap screw and M3 flat washer securing the Board Cover and remove the Board Cover. REMOVE Caution When replacing the Board Cover, be very careful not to pinch any of the cables that are routed beneath it. Fig. 3-19 Step 2 Remove the (2) stainless steel M3 x 6 socket button head screws and the [103C-106] MPF02 Board Stand securing the Controller Board. Label each of the cables attached to the Controller Board for accuracy at reassembly and disconnect the cables from the Controller Board. Remove the Controller Board. REMOVE Fig. 3-20 3-12
Step 3 Loosen the (2) upper M4 x 8 stainless steel socket flat head screws securing the Drive Assembly and remove the lower screw indicated. LOOSEN REMOVE Fig. 3-21 Step 4 Remove the (2) M3 x 5 socket flat head screws and (2) M3 x 30 stainless steel socket flat head screws securing the Motor Cover and remove the Motor Cover. REMOVE Fig. 3-22 Step 5 Open the Drive Lever to remove the tension between the Drive Roller and Idler Roller. Fig. 3-23 3-13
Step 6 Remove the E-clip from the end of the Drive Shaft. Remove the M3 x 30 socket button head screw securing the drive side plate. REMOVE Fig. 3-24 Step 7 Remove the Drive Side Plate and associated shafts and the Idler Retainer Assembly at the same time by drawing the assemblies directly away from the feeder. Fig. 3-25 Step 8 Remove the Drive Standoff, which is now free, so it does not fall off while the roller is being cleaned. Thoroughly clean the drive roller to remove any adhesive buildup. Fig. 3-26 3-14
Step 9 Remove the (2) M2.5 x 3 socket head cap screws securing the Drive Motor to the Motor Mount Assembly. Carefully remove the wires from underneath the Motor Mount Assembly. REMOVE Fig. 3-27 Note Whenever the drive unit is disassembled, it is a recommended to take the time to thoroughly clean any adhesive buildup off the drive rollers. Step 10 To install the new motor, reverse Step 9 through Step 1. Make sure the motor wires are properly routed underneath the Motor Mount Assembly. 3-15
Control Panel Replacement Warning Always disconnect all electrical power before working inside the feeder. Follow proper ESD (Electrostatic-discharge) procedures when handling electrical components inside the feeder. Use care when reinstalling covers to avoid pinching wires. Failure to heed these points may result in damage to the feeder or its electrical components.! REMOVE MOVE AND DISCONNECT MEMBRANE CABLE Step 1 Support the Control Panel. From the back side of the feeder, remove the (3) M3 x 10 socket flat head screws securing the Control Panel. Carefully move the control panel away from the base plate and disconnect the Membrane Cable from the short cable of the Membrane Control Switch.. Fig. 3-28 Step 2 Peel the old Membrane Control Switch off the Control Panel Mount, pull the cable through the hole in the Control Panel Mount, and discard the Membrane Control Switch. Push the short cable of the new Membrane Control Switch through the hole in the Control Panel Mount from the top side. Peel the backer tape off the new Membrane Control Switch. Carefully position the Membrane Control Switch in the cutout of the Control Panel Mount and press it into position so it adheres to the Control Panel Mount. Step 3 Connect the short cable from the Membrane Control Switch to the Membrane Cable. Position the Control Panel Assembly so it is aligned with the mounting holes in the base plate being careful not to pinch any wires of the cables. Insert and tighten the (3) M3 x 10 socket flat head screws to secure the Control Panel. 3-16
Chapter Four LPG01-001 Parts Lists 4
Recommended Spare Parts The chart below lists the Recommended Spare Parts for the LPG01-001 Label Feeder. The balance of this chapter shows the complete parts lists for the feeder and its subassemblies. PART NUMBER QUANTITY DESCRIPTION 0618A-0001 1 MAIN CONTROLLER 211A-S115 1 DRIVE MOTOR 0778A-0002 1 INTERFACE CABLE 0610A-0005 1 CONTROL PANEL ASSEMBLY 4-1
LPG01-001 (Bill of Materials) ITEM NO. QTY. PART NO. DESCRIPTION 1 1 191A-S74 DRIVE ASSEMBLY-56MM 2 1 576A-S01 MODULE INTERFACE ASSY 3 1 0776A-0002 SHOE 4 1 0610A-0005 CONTROL PANEL 5 1 0618A-0001 MAIN CONTROLLER 6 1 0770A-0003 LATCH SPRING HOOK 7 1 0770C-0006 BOARD COVER 8 1 0776C-0007 LINER GUIDE 9 1 105C-045 MPF MEC 44ROLLPIN 10 1 105C-034 44MM ROLLER 11 1 0770C-0008 REAR WIRE COVER 12 1 103C-106 MPF02 BOARD STAND 13 1 0770C-0009 FRONT FEEDER LATCH 14 1 0770C-0010 INTERFACE CABLE MOUNT 15 1 0930C-0059 SERIAL & BOX LABEL (3-PIECE) 16 1 0770C-0011 LATCH SHOULDER SCREW 17 1 0770C-0012 LATCH SPRING 18 1 0770C-0013 TAPE PATH LABEL 19 1 191C-089 REEL MOUNT 20 1 022C-061 REEL PIN STATOR 21 1 191C-282 REEL DRAG ORING 22 1 191C-281 DRAG INSERT 23 6 m04x08-sfhs-ss SOCKET FLAT HEAD, SS, 4 X 8 24 3 m03-lw LOCK WASHER, 3 25 2 m03x05-shcs SOCKET HEAD CAP, 3 X 5 26 1 m03x06-sbhs SOCKET BUTTON HEAD, 3 X 6 27 1 m04-lw LOCK WASHER, 4 28 1 m04x08-shcs SOCKET HEAD CAP, 4 X 8 29 9 m03x08-sfhs SOCKET FLAT HEAD, 3 X 8 30 2 m03x06-sbhs-ss SOCKET BUTTON HEAD, SS, 3 X 6 31 1 m04x08-sfhs SOCKET FLAT HEAD, 4 X 8 32 4 m025x05-sfhs SOCKET FLAT HEAD, 2.5 X 5 33 3 m03x10-sfhs SOCKET FLAT HEAD, 3 X 10 34 1 0778A-0002 INTERFACE CABLE 35 1 0778A-0003 SENSOR CABLE 36 1 0778A-0004 MEMBRANE CABLE 37 1 0770C-0014 LATCH EXTENSION PIN 38 1 700C-185 SAFETY LABEL 4-2
LPG01-001 (Front View) 4 15 38 8 24 26 2 3 37 6 13 24 25 29 36 12 27 28 24 25 16 17 9 19 22 20 21 34 10 35 5 30 14 7 29 18 1 4-3
LPG01-001 (Back View) 33 23 33 29 32 31 11 29 29 4-4
191A-S74 Drive Assembly - 56mm ITEM NO. QTY. PART NO. DESCRIPTION 1 1 0062-eclip-e ECLIP,.0625" 2 2 m03-eclip ECLIP 3 1 191A-S75 DRIVE PULLEY ASSY - 56MM 4 1 191A-S76 DRIVE IDLER ASSY - 56MM 5 1 191A-S80 DRIVE CAM ASSY - 56MM 6 1 211a-s19 DRIVE SIDE PLATE ASSY 7 1 211A-S115 DRIVE MOTOR, NEODYMIUM 8 1 211c-096r DRIVE LEVER 9 1 212a-s20 MOTOR MOUNT ASSY 10 1 212A-S127 56MM DRIVE STANDOFF ASSY 11 1 212C-177 MOTOR COVER - 56MM 12 2 m025x03-shcs SOCKET HEAD CAP, 2.5 X 3 13 2 m03x05-sfhs SOCKET FLAT HEAD, 3 X 5 14 1 m03x30-sbhs-ss SOCKET BUTTON HEAD, SS, 3 X 30 15 2 m03x30-sfhs-ss SOCKET FLAT HEAD, SS, 3 X 30 3 8 9 2 7 1 15 12 10 4 5 6 14 13 11 4-5
576A-S01 Module Interface Assembly ITEM NO. QTY. PART NO. DESCRIPTION 1 1 191C-156 M3 SHOULDER SCREW 2 1 570A-S02 LOCK LEVER ASSY 3 1 570C-012 LOCK LEVER SCREW 4 1 570C-013 LOCK LEVER WASHER 5 1 570C-014 LOCK LEVER SPRING 6 1 570C-015 POGO PIN ISOLATOR 7 1 576A-S03 MI HOUSING W/PINS ASSY 8 1 576C-016 INTERFACE HOUSING COVER 9 1 578A-002 POGO PIN ASSY 10 2 m016x06-shcs SOCKET HEAD CAP, 1.6 X 6 11 2 m025x05-sfhs SOCKET FLAT HEAD, 2.5 X 5 7 1 6 9 11 4 3 2 5 10 8 4-6
0610A-0005 Control Panel ITEM NO. QTY. PART NO. DESCRIPTION 1 1 0610C-0015 CONTROL PANEL MOUNT 2 1 558C-003 MEMBRANE CTL SWITCH 2 1 4-7
Hover-Davis, Inc., 100 Paragon Drive, Rochester, NY 14624, USA, Phone +1.585.352.9590, Fax +1.585.352.4870, sales@hoverdavis.com