Yellow Section Capacitor Sockets and Monitors, Temporary Service Adapters, Quick Set/Gen Set, Temporary Load Center, TSA, Transformer Load Management
CAPACITOR CONTROLLER SOCKET Four - Six Jaws Wire Lugs for #12-2 wire Specifications UL Recognized Marwell Housing. 600 VAC Rated. Aluminum Pole Bracket. Jaw lugs rated for # 12-2 cable or 10-32 Screw terminals optional. Strain relief option chart: PG-21 PG-16 PG-13.5 PG-9.545 -.709 inches.428 -.546 inches.270 -.470 inches.187 -.300 inches Ground Lug Select the Strain Relief Ordering Instructions: Model SP-2125-6-L-BKT (shown) - Available in 4, 5 and 6 jaw models. - Lugs standard, screw terminals optional. - Available with or without strain relief. - Specify strain relief size if needed. - Hole optional for up to 1 inch conduit. - Pole mount bracket may be deleted. - Top or Bottom conduit holes.
CAPACITOR MONITOR AMI Capacitor Monitor Fixed or Switched Capacitor Banks AMI monitors can be used on all Fixed or Switched Capacitor Banks. The internal CT reads the current on the neutral bus of the CAP bank. Capacitor monitor has a built in 100:5 amp CT. This CT will be shorted by an internal switch when meter is removed. The AMI meter stores the hourly reading and transmits the data daily to a database. The AMI Monitor has a 3 4 plastic tube running inside the enclosure that goes thru the 100/5 amp ct. Tube for neutral sensing wire. 100/5 CT SHORTING SWITCH FOR CT
Temporary Service Adapter for 4/0 Cable Designed for one, two, or three cables - size 4/0 This special adapter will safely connect either one or two number 4/0 cables to the line side jaws of a meter socket. A 4/0 neutral may also be connected. Plugs are provided for the unused cable entrance holes. The adapter may be used as either a source or load device by lifting the existing service cables from the socket lugs. Adapter Specifications.! - Patented jaw for 200 Amp continuous duty. - All components UL LISTED or Ordering Instructions: UL Recognized. Conductor size - Weatherproof 6 X 8 X 5 inch deep enclosure. - Marwell 4-Bolt 1.5 x 2 non-metallic coupler. - Sealable and Lockable cover. - Supplied with two non-metallic tamper resistant plugs to close the unused cable entrance holes. Model 1800-TSA-4/0 4/0 for 4/0 cable 3/0 for 3/0 cable 2/0 for 2/0 cable Meter socket type 1000 for Ring style 1800 for Ringless style
QUICK-SET GENERATOR ADAPTER! This new version of the Marwell generator adapter is designed to be hard wired to a standby generator. Roll out the generator with adapter already connected, pull the meter, clip the neutral, and plug-in the adapter. Just two minutes and you are safely connected. Complete isolation, no back feed to the utility power grid. May be sealed with a standard meter ring. The quick way to connect a temporary generator MARWELL QUICK-SET! OPTIONS: 120V or 240V Wire size and length to specifications Wire end termination per customer Blunt cut wire end (None) Pre-stripped Twist-lock plug Straight blade plug Use the GEN-SET version for meter storage ORDERING INFORMATION: Contact Marwell and specify you requirements for either the QUICK-SET or GEN-SET adapter. Specify: Voltage Amp rating Wire length Wire end connection type GEN-SET with meter storage
Temporary Service Adapters LINE / LOAD 1800-1-TSA-2/0 Source Side 1800-1-TSA-2/0 Load Side Adapter Rated For 200 Amps MAX 160 Amps Continuous Maximum Conductor Size 2/0 AWG Line Side, 1/0 AWG Neutral Lug Adapter Rated For 160 Amps Max 135 Amps Continuous Maximum Conductor Size 2/0 # 2 AWG Neutral Lead With Heavy Duty Terminal End Hub Size 2 Polycarbonate Combined Load Rating Of Adapters Installed As A Pair 200 Amps Max, 160 Amps Cont. Line Side, 1/0 AWG Neutral Lug #2 AWG Neutral Lead With Heavy Duty Terminal End Hub Size 2 Polycarbonate Line Side Stabs Of Adapter Are Isolated From Metered Side Of Adapter. Line Side Only
TSA TEMPORARY SERVICE ADAPTERS Specifications * TSA-LINE Rated for 200 Amp continuous combined load. * TSA-LOAD Rated for 100 Amp continuous standard. Higher rating optional. * Each meter registers only one house. * Modified UL Listed adapter with UL Recognized components throughout. * Will not back feed the faulted cable. Temporary repair of failed underground. A large southern utility came to us for a heavy duty set of Temporary Service Adapters, something to help them connect jumper cables to a meter socket in the event of a failed service at a residence. The jumper cable is actually a length of #2 Triplex. The night emergency crew normally runs it on the ground to bring power into a home until a day crew can get back and make a proper repair. The adapters needed to be rugged for repeated reuse and the source adapter must be able to handle the high current load of two houses. The Marwell TSA is up to the task. The TSA-LOAD is attached to the end of the cable and inserted in the meter socket of the dark house. The TSA-LINE is attached to the other end of the cable and inserted in a neighbors house that has power. The meter in each adapter measures only the consumption of its respective home. Ordering Instructions: 1000-TSA-LINE Source adapter for ring style systems, 200 Amp continuous combined load 1000-TSA-LOAD Load adapter for ring style systems. 1800-TSA-LINE Source adapter for ringless systems, 200 Amp continuous combined load 1800-TSA-LOAD Load adapter for ringless systems.
Transformer Load Management Adapter and Energy Diversion Mount the Marwell TLM Adapter at the transformer site and install Smart Meter. Use Smart Meter to collect and transmit data from transformer site. Marwell Corporation pole mounted Transformer Load Management adapter is available in two different current ratings in self-contained units. Marwell Part # TLM-2s-200A Rated 200 Amps Continuous, 600V rated. Marwell Part # TLM-2s-400A Rated 320 Amps Continuous, 600V