DRAFTS IN WIDE CIRCULATION DOCUMENT DESPATCH ADVICE Ref. Date MED 7 /T- 170 02 01 2019 Material Handling Systems and Equipment Sectional Committee, MED 07 1) All Members of Mechanical Engineering Division Council 2) All Members of Material Handling Systems and Equipment Sectional Committee, MED 07 3) All other interested members Dear Sirs, Please find enclosed the following documents: Doc No. MED 07 (13434) Title Earth-moving machinery Rubber-tyred machines Steering requirements (Adoption of ISO 5010:2007) Kindly examine the draft standards and forward your views, stating any difficulties which you are likely to experience in your business or profession, if they are finally adopted as National Standards. Last date for comments: 05 03 2019 Comments, if any, may please be made in the format as given overleaf and mailed to the undersigned at the above address. In case no comments are received or comments received are of editorial nature, you will kindly permit us to presume your approval for the above document as finalized. However, in case of comments of technical in nature are received then it may be finalized either in consultation with the Chairman, Sectional Committee or referred to the Sectional committee for further necessary action if so desired by the Chairman, Sectional Committee. This document is also hosted on BIS website www.bis.org.in Thanking you, Yours faithfully, Encl.: As above (Rajneesh Khosla) Sc `E & Head (MED)
व य पक प पक च ल म द दर ष टद न र वमईड 7/ 170 02 01 2019 म ट र यल ह डलल ग ल स म वमम पकर वमषय लमत, वमईड 7 प र ष त : 1 य त र प इ ज तमय ष भ ग पक च प दभ द स य 2 ट च य ह डल ग लदस व पपक प ष य दल त, व ईड 7 प दभ द स य 3 र चल खम अन य तमप य ह य, तमम मल ख मप प द द ग म ह : प रल ख ख य व ईड 7 (13434) श षषर -द ल म श म - बड य श म - जस यच ग अपक क ष य [आईवदओ 5010 : 2007 प अच ग रह ] प पकय इम द प अ पम प औ अपकम दम त य यह ब हएव भ प अ : यट य मप ष ट र य मप प र पक प रप लश ह इम पक अ प म आपकप व य द य अव प ब य पट म ईय आ दप ह दम त य भ म प अजन त चव 05 03 2019 दम त यट प ई ह प पकय अ हस क ष प पपक ल ख पक पक द ग म मट भ य ई प यट प ई दम त प र मह ह ह अव दम त प भ द ब एट हएई पपक प र ख प यव अ त र पक ट य य ग यट प ई दम त पम प प रप त प हएई ष य दल त प अघ यक ष प पक शमट द अव पमप इच छ पक आग प प यमट ह प ल व ष य दल त प भ म प ब प र ख प अ त र पक ट य वग यह प र ख भ य मप ब य प बद इ www.bis.org.in पक भ पपक ब ह न य, भ य,
ल रग न : पक ललखख ( जन श ख ल ) म ज ञ तनर `ई वम प रम ख (वमईड )
IS/ISO 5010 : 2007 Doc: MED 07(13434)c For Comments Only भ रत य म नक मस द म द -स च लन मश नर - रबड ट यर व ल मश न - स टटयरर ग अप क ष य [आईएसओ 5010 : 2007 क अध ग रहण] Draft Indian Standard Earth-moving machinery Rubber-tyred machines Steering requirements (Adoption of ISO 5010:2007) ICS 53.100 Not to be reproduced without the permission of Last date for receipt of BIS or used as a STANDARD comments is: 05 March 2019 NATIONAL FOREWORD (Adoption clause to be added later on). In the adopted standard certain terminology and conventions are not identical with those used in Indian Standards; attention is drawn specially to the following: a) Comma (,) has been used as a decimal marker while in Indian Standards the current practice is to use a point (.) as the decimal marker. b) Wherever the words International Standard appear, referring to this standard, they should be read as Indian Standard. In the adopted standard, reference appears to certain International Standards for which Indian Standards also exist. The corresponding Indian Standards which are to be substituted in their places are listed below along with their degree of equivalence for the edition indicated: International Standard Corresponding Indian Standard Degree of Equivalence ISO 6014 Earth-moving machinery Determination of ground speed IS/ISO 6014:1986 Earth-moving machinery Determination of ground speed
IS/ISO 5010 : 2007 Doc: MED 07(13434)c ISO 6165 Earth-moving machinery Basic types Identification and terms and definitions ISO 7457 Earth-moving machinery Determination of turning dimensions of wheeled machines ISO 10968 Earth-moving machinery Operator s controls IS/ISO 6165:2012 Earth-moving machinery Basic types Identification and terms and definitions IS/ISO 7457:1997 Earth-moving machinery Determination of turning dimensions of wheeled machines IS/ISO 10968:2004 Earth-moving machinery Operator s controls The technical committee has reviewed the provisions of the following International Standards referred in this adopted standard and has decided that they are acceptable for use in conjunction with this standard: Internationa l Standard ISO 3450 ISO 13849 (all parts) ISO 15998 IEC 62061 Corresponding Indian Standard Earth-moving machinery Braking systems of rubber-tyred machines Systems and performance requirements and test procedures Safety of machinery Safety-related parts of control systems Earth-moving machinery Machine-control systems (MCS) using electronic components Performance criteria and tests for functional safety Safety of machinery Functional safety of safety-related electrical, electronic and programmable electronic control systems For the purpose of deciding whether a particular requirement of this standard is complied with, the final value, observed or calculated, expressing the result of a test or analysis shall be rounded off in accordance with IS 2:1960 Rules for rounding off numerical values (revised). The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard. FOR COMPLETE TEXT PLEASE REFERE TO ISO 5010: 2007. IF ANY ONE REQUIRES A HARD COPY OF THE SAME PLEASE CONTACT THE UNDER SIGNED. Rajneesh Khosla
Sc-E and Head (Mechanical Engineering Department) Manak Bhavan 9 Bhadurshah Zafar Marg New Delhi 110002 Telefax 011-23232509 Email: med@bis.org.in IS/ISO 5010 : 2007 Doc: MED 07(13434)c
FORMAT FOR SENDING COMMENTS ON BIS DOCUMENTS (Please use A4 size sheet of paper only and type within fields indicated. Comments on each clauses/subclauses/table/fig. etc be started on a fresh box. Information in Column 4 should include reasons for the comments and suggestions for modified wording of the clauses when the existing text is found not acceptable. Adherence to this format facilitates Secretariat s work) It is desirable to send comments through email at : med@bis.org.in. IS. No./ Doc. No.: TITLE : NAME OF THE COMMENTATOR /ORGN.: Sl. No. Clause/Subclause/ para/table/fig. No. commented Comments Justification Proposed change