DRAFTS IN WIDE CIRCULATION DOCUMENT DESPATCH ADVICE Ref. Date MED 7 /T- 190, 02 01 2019 Material Handling Systems and Equipment Sectional Committee, MED 07 1) All Members of Mechanical Engineering Division Council 2) All Members of Material Handling Systems and Equipment Sectional Committee, MED 07 3) All other interested members Dear Sirs, Please find enclosed the following documents: Doc No. MED 07 (13428) Title Fork-lift trucks Fork arms Technical characteristics and testing (Adoption of ISO 2330:2002) Kindly examine the draft standards and forward your views, stating any difficulties which you are likely to experience in your business or profession, if they are finally adopted as National Standards. Last date for comments: 05 03 2019 Comments, if any, may please be made in the format as given overleaf and mailed to the undersigned at the above address. In case no comments are received or comments received are of editorial nature, you will kindly permit us to presume your approval for the above document as finalized. However, in case of comments of technical in nature are received then it may be finalized either in consultation with the Chairman, Sectional Committee or referred to the Sectional committee for further necessary action if so desired by the Chairman, Sectional Committee. This document is also hosted on BIS website www.bis.org.in Thanking you, Yours faithfully,
Encl.: As above (Rajneesh Khosla) Sc `E & Head (MED) व य पक प पक च ल म द स दर भ दद न क एमईड 7/ट 190 02 01 2019
म दटर यल ह डलल ग लसस टम एमम पकक वमषय सलमत, एमईड 7 प र ष त : 1 य त र प इ ज तमय ष भ ग पक च प दभ द स य 2 ट च य ह डल ग लदस व पपक प ष य दल त, व ईड 7 प दभ द स य 3 र चल खम अन य तमप य ह य, तमम मल ख मप प द द ग म ह : प रल ख स ख य श षभक व ईड 7 (13428) फ कभ ल फ़ ट रक - फ कभ आमभ - कन क अलर लक ष एम क क ष [आईवदओ 2330:2002 प अच ग रह ] प पकय इम द प अ पम प औ अपकम दम त य यह त हएव भ प अ : यट य मप ष ट र य मप प र पक प रप ल ह इम पक अ प म आपकप व य द य अव प त य पट म ईय आ दप ह दम त य भ म प अजन त चव 05 03 2019 दम त यट प ई ह प पकय अ हस क षर प पपक ल ख पक पक द ग म मट भ य ई प यट प ई दम त प र मह ह ह अव दम त प भ द त एट हएई पपक प र ख प यव अ त र पक ट य य ग यट प ई दम त पम प प रप त प हएई ष य दल त प अघ यक षर प पक मट द अव पमप इच छ पक आग प प यमट ह प ल व ष य दल त प भ म प त प र ख प अ त र पक ट य वग यह प र ख भ य मप ब य प तद इ www.bis.org.in पक भ पपक ब ह न य, भ य, स ल रग न : पक ललखख ( जन श ख सल ) म ज ञ तनक `ई एम प रम ख (एमईड )
IS/ISO 2330 : 2002 Doc: MED 07(13428)c For Comments Only भ रत य म नक मस द फ र क ल फ़ ट ट रर - फ र क आर क - तर न र अभ लक षण एव पर क षण [आईएसओ 2330:2002 क अध ग रहण] Draft Indian Standard Fork-lift trucks Fork arms Technical characteristics and testing (Adoption of ISO 2330:2002) ICS 53.060 Not to be reproduced without the permission of Last date for receipt of BIS or used as a STANDARD comments is: 05 March 2019 NATIONAL FOREWORD (Adoption clause to be added later on). In the adopted standard certain terminology and conventions are not identical with those used in Indian Standards; attention is drawn specially to the following: a) Comma (,) has been used as a decimal marker while in Indian Standards the current practice is to use a point (.) as the decimal marker. b) Wherever the words International Standard appear, referring to this standard, they should be read as Indian Standard. The technical committee has reviewed the provisions of the following International Standards referred in this adopted standard and has decided that they are acceptable for use in conjunction with this standard: International Standard Corresponding Indian Standard ISO 148:1983 Steel Charpy impact test (V-notch) ISO 683-1:1987 Heat-treatable steels, alloy steels and free-cutting steels Part 1: Direct-hardening unalloyed and low-alloyed wrought steel in form of different black products ISO 2328:1993 Fork-lift trucks Hook-on type fork arms and fork arm
IS/ISO 2330 : 2002 Doc: MED 07(13428)c ISO 2331:1974 carriages Mounting dimensions Fork lift trucks Hook-on type fork arms Vocabulary For the purpose of deciding whether a particular requirement of this standard is complied with, the final value, observed or calculated, expressing the result of a test or analysis shall be rounded off in accordance with IS 2:1960 Rules for rounding off numerical values (revised). The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard. FOR COMPLETE TEXT PLEASE REFERE TO ISO 2330: 2002. IF ANY ONE REQUIRES A HARD COPY OF THE SAME PLEASE CONTACT THE UNDER SIGNED. Rajneesh Khosla Sc-E and Head (Mechanical Engineering Department) Manak Bhavan 9 Bhadurshah Zafar Marg New Delhi 110002 Telefax 011-23232509 Email: med@bis.org.in
FORMAT FOR SENDING COMMENTS ON BIS DOCUMENTS (Please use A4 size sheet of paper only and type within fields indicated. Comments on each clauses/subclauses/table/fig. etc be started on a fresh box. Information in Column 4 should include reasons for the comments and suggestions for modified wording of the clauses when the existing text is found not acceptable. Adherence to this format facilitates Secretariat s work) It is desirable to send comments through email at : med@bis.org.in. IS. No./ Doc. No.: TITLE : NAME OF THE COMMENTATOR /ORGN.: Sl. No. Clause/Subclause/ para/table/fig. No. commented Comments Justification Proposed change