CA 1 Tape Management CA RS 1306 Service List

CA 1 Tape Management 12.6 1 CA RS 1306 Service List Description Hiper 12.6 RO51540 TMSOCEPR S0C4 for tape datasets if NON_VSAM_XTIOT is enabled RO51541 S0C4 when DEVSUPxx NON_VSAM_XTIOT=YES RO51542 S0C4 with UCB's above the line and a DCB extension RO52616 Invalid SMFQ FULL condition RO53023 ENHANCEMENT: SMF RECOVERY UTILITY RO54501 ADDITION OF TWO HEALTH CHECKS RO54511 ENHANCEMENT: Support TRTCH of (EF4) for device type TS1140 RO54912 Correction of various minor TMSAPEC problems RO55004 Usermods CTSUCBX and CTSUCBR receive ERROR GIM20311E RO55175 TMSGRW ERR58 RO55176 A rare S0C4 abend in TMSAUDEX when invoked by TMSXTEND RO55480 ENHANCEMENT: VOLUME POOL MONITOR The CA RS 1306 service count for this release is 12

CA 1 Tape Management 12.0 2 CA RS 1306 Service List Description Hiper 12.0 RO51543 TMSOCEPR S0C4 for tape datasets if NON_VSAM_XTIOT is enabled RO51544 S0C4 when DEVSUPxx NON_VSAM_XTIOT=YES RO51545 S0C4 with UCB's above the line and a DCB extension The CA RS 1306 service count for this release is 3

CA 1 Tape Management 3 CA RS 1306 Service List for CAG8C00 FMID Service Description Hiper CAG8C00 RO51545 S0C4 with UCB's above the line and a DCB extension The CA RS 1306 service count for this FMID is 1

CA 1 Tape Management 4 CA RS 1306 Service List for CAG8C60 FMID Service Description Hiper CAG8C60 RO51542 S0C4 with UCB's above the line and a DCB extension The CA RS 1306 service count for this FMID is 1

CA 1 Tape Management 5 CA RS 1306 Service List for CAL0C00 FMID Service Description Hiper CAL0C00 RO51543 TMSOCEPR S0C4 for tape datasets if NON_VSAM_XTIOT is enabled The CA RS 1306 service count for this FMID is 1

CA 1 Tape Management 6 CA RS 1306 Service List for CAL0C60 FMID Service Description Hiper CAL0C60 RO51540 TMSOCEPR S0C4 for tape datasets if NON_VSAM_XTIOT is enabled RO52616 Invalid SMFQ FULL condition RO53023 ENHANCEMENT: SMF RECOVERY UTILITY RO54501 ADDITION OF TWO HEALTH CHECKS RO54511 ENHANCEMENT: Support TRTCH of (EF4) for device type TS1140 RO54912 Correction of various minor TMSAPEC problems RO55175 TMSGRW ERR58 RO55176 A rare S0C4 abend in TMSAUDEX when invoked by TMSXTEND RO55480 ENHANCEMENT: VOLUME POOL MONITOR The CA RS 1306 service count for this FMID is 9

CA 1 Tape Management 7 CA RS 1306 Service List for CBAFC00 FMID Service Description Hiper CBAFC00 RO51544 S0C4 when DEVSUPxx NON_VSAM_XTIOT=YES The CA RS 1306 service count for this FMID is 1

CA 1 Tape Management 8 CA RS 1306 Service List for CBAFC60 FMID Service Description Hiper CBAFC60 RO51541 S0C4 when DEVSUPxx NON_VSAM_XTIOT=YES RO55004 Usermods CTSUCBX and CTSUCBR receive ERROR GIM20311E The CA RS 1306 service count for this FMID is 2

CA 1 Tape Management 12.6 9 CA RS 1306 - PTF RO51540 12.6 RO51540 RO51540 M.C.S. ENTRIES = ++PTF(RO51540) DESC(TMSOCEPR S0C4 for tape datasets if NON_VSAM_XTIOT is enabled). ++VER(Z038) FMID(CAL0C60) SUP(T5XD749) Applications exploiting the new z/os 1.12 dynamic allocation option to not capture the UCB during OPEN processing and have the new DEVSUPxx parmlib option NON_VSAM_XTIOT set to YES, will receive a S0C4 abend during OPEN processing for tape datasets if the UCB itself is a 31-bit UCB address. S0C4 Abend in module TMSOCEAP. Tape datasets may abend with a S0C4 during OPEN processing. Set the NON_VSAM_XTIOT option to NO in the DEVSUPxx member of SYS1.PARMLIB and reset it dynamically (SET DEVSUP=xx). PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 RELATED PROBLEM(S): 1975 ++IF FMID(CBAFC60) THEN REQ(RO51541). ++IF FMID(CAG8C60) THEN REQ(RO51542). ++HOLD(RO51540) SYSTEM REASON(DYNACT) FMID(CAL0C60) Re-IPL the system, or run the CAS9 procedure specifying the following parm for the CA 1 program L0C0INIT (R12.0) or L0C6INIT (R12.6) PARM(REINIT,OSI=REINIT) LOADLIB(your CA 1 load library) ).

CA 1 Tape Management 12.6 10 CA RS 1306 - PTF RO51541 12.6 RO51541 RO51541 M.C.S. ENTRIES = ++PTF(RO51541) DESC(S0C4 when DEVSUPxx NON_VSAM_XTIOT=YES). ++VER(Z038) FMID(CBAFC60) SUP(T5XD735) Applications exploiting the new z/os 1.12 dynamic allocation option to not capture the UCB during OPEN processing and have the new DEVSUPxx parmlib option NON_VSAM_XTIOT set to YES, will receive a S0C4 abend during CLOSE processing for tape datasets if the UCB itself is a 31-bit UCB address. S0C4 abend in CTSOCE00. Tape datasets may abend with a S0C4 during CLOSE processing. Set the NON_VSAM_XTIOT option to NO in the DEVSUPxx member of SYS1.PARMLIB and reset it dynamically (SET DEVSUP=xx). PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 CA TLMS Tape Management Release: 12.6 RELATED PROBLEM(S): 190 ++HOLD(RO51541) SYSTEM REASON(DYNACT) FMID(CBAFC60) Re-IPL the system, or run the CAS9 procedure specifying the following parm for the CA 1 program L0C0INIT (r12.0) or L0C6INIT (r12.6) or the CA TLMS program TLC0INIT (r12.0) or TLC6INIT (r12.6); PARM(REINIT,LPA=CTSOCE00) ).

CA 1 Tape Management 12.6 11 CA RS 1306 - PTF RO51542 12.6 RO51542 RO51542 M.C.S. ENTRIES = ++PTF(RO51542) DESC(S0C4 with UCB's above the line and a DCB extension). ++VER(Z038) FMID(CAG8C60) SUP(T5XD772) An S0C4 abend may occur if a tape UCB is a 31 bit UCB address and a DCB extension is being used with new Dynamic Allocation settings that eliminate the need to create a captured UCB below the line. S0C4 Abend in module G8WTG. Both tape and non-tape allocations may abend with a S0C4 during OPEN processing. None PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 CA TLMS Tape Management Release: 12.6 RELATED PROBLEM(S): 22 ++HOLD(RO51542) SYSTEM REASON(DYNACT) FMID(CAG8C60) Re-IPL the system, or run the CAS9 procedure specifying the following parm for the CA 1 program L0C0INIT (r12.0) or L0C6INIT (r12.6) or the CA TLMS program TLC0INIT (r12.0) or TLC6INIT (r12.6); PARM(REINIT,OSI=REINIT) ).

CA 1 Tape Management 12.6 12 CA RS 1306 - PTF RO52616 12.6 RO52616 RO52616 M.C.S. ENTRIES = ++PTF(RO52616) DESC(Invalid SMFQ FULL condition). ++VER(Z038) FMID(CAL0C60) PRE(RO47199) SUP(T5XD785) The CTS SMFQ subtask reports that records are skipped due to the queue being full after a small amount of processing. The records that are skipped are handled by TMSSMFCT directly, so no records are actually lost. A CTS SMFQ status command displays messages TMSSMFQ-29I and TMSSMFQ-30I indicating that the SMF queue has been filled a certain amount of times. TMSSMFQ-29I NUMBER OF RECORDS SKIPPED DUE TO FULL:0 TMSSMFQ-30I NUMBER OF TIMES QUEUE FILLED: 0 Some updates to the TMC are done by the SMFQ subtask and others are done by the TMSSMFCT module directly. No updates are actually lost or skipped. Disable the CTS SMFQ subtask. PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 RELATED PROBLEM(S): 2110 ++HOLD(RO52616) SYSTEM REASON(DYNACT) FMID(CAL0C60) Re-IPL the system, or run the CAS9 procedure specifying the following parm for the CA 1 program L0C6INIT. PARM(REINIT,LPA=TMSSMF83,SMF=YES) - LOADLIB(your CA 1 load library) ).

CA 1 Tape Management 12.6 13 CA RS 1306 - PTF RO53023 12.6 RO53023 RO53023 M.C.S. ENTRIES = ++PTF(RO53023) DESC(ENHANCEMENT: SMF RECOVERY UTILITY). ++VER(Z038) FMID(CAL0C60) SUP(T5V3005) The TMSSMF utility allows recovery of tape records and DSNBs from SMF data for periods of time when CA 1 was inactive but tape processing was allowed to continue. SMF must have been active and recording type 14 and 15 records for the period of time that CA 1 was down. The SMF records will be used to create TMSUPDTE and TMSAGGR files to update the TMC. Documentation for this utility is provided in Informational Solution RI53024. N/A N/A Manually create TMSUPDTE and TMSAGGR input files to recover volume and file information. PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 RELATED PROBLEM(S): 2071 ++HOLD(RO53023) SYSTEM REASON(DOC) FMID(CAL0C60) Refer to RI53024 for more information. ).

CA 1 Tape Management 12.6 14 CA RS 1306 - PTF RO54501 12.6 RO54501 RO54501 M.C.S. ENTRIES = ++PTF(RO54501) DESC(ADDITION OF TWO HEALTH CHECKS). ++VER(Z038) FMID(CAL0C60) This PTF provides two new health checks that ensure your tape environment is being protected properly when IBM's RACF external security system is in use. CA1_Vrfy_Security_Profile_TAPE ensures your tapes are protected from unauthorized access and CA1_Vrfy_Security_Profile_CMD ensures CA 1 operational commands are restricted to authorized users. The checks are made when TMSINIT runs. A status message is updated upon completion telling the user whether or not the check was successful. Two more checks will be displayed notifying the user if an error was found with the CA@APE or CA@MD resource classes. None. PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 RELATED PROBLEM(S): 2115 ++HOLD(RO54501) SYSTEM REASON(DOC) FMID(CAL0C60) Product: CA 1 Release 12.6 Publication: CA 1 Administration Guide Updates to Appendix B "CA 1 Health Checks" for the 2 new checks are documented in PDC RI55646. Publication: CA 1 Best Practices Guide PDC RI55646 includes updates to be made at the end of Chapter 2 to the section titled "Monitor the CA 1 Health Checks". Publication: CA 1 Messages Guide PDC RI55646 includes the new messages TMSH0161E and TMSH0171E issued by the Health Checks. ). ++HOLD(RO54501) SYSTEM REASON(DYNACT) FMID(CAL0C60) Product: CA 1 Release: 12.6 Sequence: Apply PTF Purpose: To activate this PTF prior to an IPL Relevance: If you want to activate this PTF prior to your next IPL follow these instructions. Knowledge required: Ability to issue z/os commands and how to restart CA 1. Access required: Access to issue operator commands and to run TMSINIT. Steps to Perform: After the maintenance has been applied, activate the new health checks without an IPL using this procedure. It will delete all CA 1 health checks (identified using the Task name OWNERxxx assigned to CA 1 checks) and then add them all again by running TMSINIT. This will pick up the two new checks in addition to all other CA 1 checks. 1. Issue the MVS console command F LLA,REFRESH 2. Delete the current CA 1 health checks: mand: Display CA 1 Health Check tasks by issuing the following MVS mand: console command: F CAHC,DISPLAY TASK Note the Task name OWNERxxx assigned to the CA_1 task in the CAHC151I message. Issue MVS console command: F CAHC,DELETE OWNERxxx

CA 1 Tape Management 12.6 15 CA RS 1306 - PTF RO54501 3. Run TMSINIT to pick up the new health checks. ).

CA 1 Tape Management 12.6 16 CA RS 1306 - PTF RO54511 12.6 RO54511 RO54511 M.C.S. ENTRIES = ++PTF(RO54511) DESC(ENHANCEMENT: Support TRTCH of (EF4) for device type TS1140). ++VER(Z038) FMID(CAL0C60) PRE(RO38530 RO42220 RO45757 RO46753 RO52223) SUP(T246218) For IBM 3592 cartridges, CA 1 needs to identify and record Enterprise Format 4 (EFMT4) recording technique used by TS1140 devices. This PTF introduces the following new TRTCH values, applicable to normal 3592 and to WORM cartridges: TMEF4 D5 X'D5' EF4 3592 cartridge created in format 4 TMEF4M D6 X'D6' EF4M 3592 economy cart created in format 4 TMEF4X D7 X'D7' EF4X 3592 extended length cart format 4 TMEE4 D8 X'D8' EE4 3592 cartridge created in format 4 encrypted TMEE4M D9 X'D9' EE4M 3592 economy cart created in format 4 encrypted TMEE4X DA X'DA' EE4X 3592 extended length cart format 4 encrypted Cartridges created on TS1140 devices are recorded as 3592 format 1 cartridges instead of as 3592 format 4 cartridges. Low, this is a reporting field only. None available. PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 RELATED PROBLEM(S): 2098 ++HOLD(RO54511) SYSTEM REASON(DOC) FMID(CAL0C60) Product: CA 1 Release 12.6 Publication: CA 1 Programming Guide The following values need to be added to the PROGRAMMING GUIDE in Appendix A for the VOLUME record layout. These need to be placed after TMT1BS D2 entry in the TRTCH values. TMEF4 D5 X'D5' EF4 3592 cartridge created in format 4 TMEF4M D6 X'D6' EF4M 3592 economy cart created in format 4 TMEF4X D7 X'D7' EF4X 3592 extended length cart format 4 TMEE4 D8 X'D8' EE4 3592 cartridge created in format 4 encrypted TMEE4M D9 X'D9' EE4M 3592 economy cart created in format 4 encrypted TMEE4X DA X'DA' EE4X 3592 extended length cart format 4 encrypted ). ++HOLD(RO54511) SYSTEM REASON(DYNACT) FMID(CAL0C60) Product: CA 1 Release: 12.6 Sequence: Apply PTF Purpose: To activate this PTF prior to an IPL Relevance: If you want to activate this PTF prior to your next IPL follow these instructions. Knowledge required: Know how to run the CAS9 proc that executes program CAIRIM. Access required: Ability to run the CAS9 with a modified input control file. Steps to Perform: Run the CAS9 procedure specifying the following parm for the program L0C6INIT. PARM(REINIT,LPA=TMS00SVC,SVC=XXX) - LOADLIB(hlq.CTAPLINK) PARM(REINIT,LPA=TMSKEYXB) LOADLIB(hlq.CTAPLINK) Also, you must log off and log back onto ISPF to use the new

CA 1 Tape Management 12.6 17 CA RS 1306 - PTF RO54511 ISPF panels. ).

CA 1 Tape Management 12.6 18 CA RS 1306 - PTF RO54912 12.6 RO54912 RO54912 M.C.S. ENTRIES = ++PTF(RO54912) DESC(Correction of various minor TMSAPEC problems). ++VER(Z038) FMID(CAL0C60) PRE(RO42220 RO49573) Three small problems with the CTS APEC subtask are addressed with this PTF: 1) ERR79 was showing the DSN17 field as having been corrected when it was not. HEXZEROS is a valid value for DSN17 and as such there is no correction to the field. There will still be a warning message issued when DSN17 is HEXZEROS. 2) ERR24 is no longer being duplicated on TMSRPT. Before it was incorrectly being reported twice when the message "AND CHAINS THRU END OF CHAIN" was displayed. 3) ERR56 now will display when a DSNB has an incorrect AUFLAG1, and will now correct the record if APEC is in UPDATE mode. 1) ERR79 was showing to be corrected when it is not being corrected. 2) ERR24 was duplicating a single entry improperly. 3) ERR56 was not being checked or corrected in APEC scans. Low, mainly just reporting changes. None. PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 RELATED PROBLEM(S): 2120 ++HOLD(RO54912) SYSTEM REASON(DYNACT) FMID(CAL0C60) Product: CA 1 Release: 12.6 Sequence: Apply PTF Purpose: To activate this PTF prior to an IPL Relevance: If you want to activate this PTF prior to your next IPL follow these instructions. Knowledge required: Know how to stop and restart the CTS started task. Access required: Access to issue operator stop and start commands. Steps to Perform: After the maintenance has been applied, STOP the CTS started task and then restart it. ).

CA 1 Tape Management 12.6 19 CA RS 1306 - PTF RO55004 12.6 RO55004 RO55004 M.C.S. ENTRIES = ++PTF(RO55004) DESC(Usermods CTSUCBX and CTSUCBR receive ERROR GIM20311E). ++VER(Z038) FMID(CBAFC60) PRE(RO49792) SUP(T5XD746) Unable to receive usermods CTSUCBR and CTSUCBX due to a construction error in the ++USERMOD statement. 'GIM20311E issued during receive processing' issued by SMPE. Unable to install usermods. Add a '.' after the ++USERMOD statement. PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 CA TLMS Tape Management Release: 12.6 RELATED PROBLEM(S): 230

CA 1 Tape Management 12.6 20 CA RS 1306 - PTF RO55175 12.6 RO55175 RO55175 M.C.S. ENTRIES = ++PTF(RO55175) DESC(TMSGRW ERR58). ++VER(Z038) FMID(CAL0C60) PRE(RO42220) SUP(T246224) If a user only uses a single character to define a field in the CONTROL-SECTION of TMSGRW, it is possible for the job to end with a condition code 4 and not produce the desired report and have an error message written to the job report: For example: CONTROL-SECTION DEFINE ONE CH '1' DEFINE SIX CH '6' DEFINE DR CH '7' DEFINE B CH 'B' *** ERROR IN PREVIOUS LINE, CODE = 058 PREVIOUSLY DEFINED TMSGRW ends with a CONDITION CODE 4. TMSGRW will not create the report. Make the field definition name more than one character. PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 RELATED PROBLEM(S): 2124

CA 1 Tape Management 12.6 21 CA RS 1306 - PTF RO55176 12.6 RO55176 RO55176 M.C.S. ENTRIES = ++PTF(RO55176) DESC(A rare S0C4 abend in TMSAUDEX when invoked by TMSXTEND). ++VER(Z038) FMID(CAL0C60) PRE(RO42220) SUP(T246225) TMSXTEND may abend with a S0C4 that occurs in TMSAUDEX. This is a rare occurrence having to do with a residual value in a register that was not cleared before being used. TMSXTEND fails and the extend process will not continue. Unable to ADD or REMOVE volumes or DSNB's using TMSXTEND. None, the PTF must be APPLIED. PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 RELATED PROBLEM(S): 2126

CA 1 Tape Management 12.6 22 CA RS 1306 - PTF RO55480 12.6 RO55480 RO55480 M.C.S. ENTRIES = ++PTF(RO55480) DESC(ENHANCEMENT: VOLUME POOL MONITOR). ++VER(Z038) FMID(CAL0C60) PRE(RO27818 RO34565 RO35023 RO42220 RO46585 RO51983 RO51984) SUP(T5Q3229 T5Q3231) This enhancement provides a new way to monitor volume activity and scratch availability for pools of tapes. The Volume Pool Monitor is implemented as a new CTS subtask, VPM. A new CA 1 VSAM file known as the VDB or VSAM Data Base is required for this feature. This feature also provides the ability to issue customized emails or WTO alerts for conditions defined by the user through new ISPF panels. The emails and WTOs can be issued by the VPM subtask or through a new utility CTSMAIL. The CA 1 12.6 manual set has been updated to include documentation for this feature, available on http://support.ca.com. The cover pages for this version of the documentation will show "Fourth Edition." N/A N/A N/A PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.6 RELATED PROBLEM(S): 2072 ++IF FMID(CBAFC60) THEN REQ(RO55481). ++HOLD(RO55480) SYSTEM REASON(ACTION) FMID(CAL0C60) Product: CA 1 Release: 12.6 Sequence: Apply PTF Purpose: CA 1 ISPF Primary panel TMPI@PRI, has been updated. Relevance: If you want to activate this PTF follow these instructions. Knowledge required: Know how to use ISPF EDIT and the location of your TMPI@PRI panel. Access required: Ability to update and make made changes to your TMPI@PRI panel. Steps to Perform: The CA 1 ISPF Primary panel TMPI@PRI, has been updated by this PTF to invoke the new CTS Primary Menu. If you have made changes to your TMPI@PRI panel, you should make a backup copy of it, prior to applying this PTF. Once this PTF has been applied, your changes can be then be re-applied. ). ++HOLD(RO55480) SYSTEM REASON(DOC) FMID(CAL0C60) Product: CA 1 Release 12.6 Documentation for the CA 1 Volume Pool Monitor Feature is provided in CA 1 12.6 Fourth Edition, available for download from CA Support Online. The following CA 1 12.6 guides have been updated for this feature. CA 1 Release Notes - Volume Pool Monitor feature summary has been added to Chapter 1, "New Features"

CA 1 Tape Management 12.6 23 CA RS 1306 - PTF RO55480 CA 1 Installation Guide - A new section "Install the Volume Pool Monitor" has been added to Chapter 6, "Starting Your Product". CA 1 Overview Guide - A new section "Real-time Alert Monitoring" has been added to Chapter 9, "Other Features". CA 1 Administration Guide - A new section "CTS ISPF Facility" has been added to Chapter 7, "Using Online Inquiry and Update Facilities". - Chapter 10, "Common Tape System" has been updated to include a new section "Volume Pool Monitor (VPM)" - A new Chapter 11 has been added, "Using the Volume Pool Monitor Alert and Email Facilities" CA 1 Programming Guide - Added the following new sections to Chapter 3, "Data Set Requirements" - "SEND Data Set - Optional" - "VSAM Database - Optional" CA 1 Utilities and Reports Guide - Added the following new sections to Chapter 2, "Utilities" "CTSMAIL - EMAIL/WTO UTILITY" "CTSVDBU - VSAM DATABASE UTILITY" ). ++HOLD(RO55480) SYSTEM REASON(DYNACT) FMID(CAL0C60) Product: CA 1 Release: 12.6 Sequence: Apply PTF Purpose: To activate this PTF prior to an IPL Relevance: If you want to activate this PTF prior to your next IPL follow these instructions. Knowledge required: Know how to run the CAS9 proc that executes program CAIRIM. Access required: Ability to run the CAS9 with a modified input control file. Steps to Perform: Run the CAS9 procedure specifying the following parm for the program L0C6INIT. PARM(REINIT,LPA=ALL,SVC=NNN) - LOADLIB(your CA 1 load library) ).

CA 1 Tape Management 12.0 24 CA RS 1306 - PTF RO51543 12.0 RO51543 RO51543 M.C.S. ENTRIES = ++PTF(RO51543) DESC(TMSOCEPR S0C4 for tape datasets if NON_VSAM_XTIOT is enabled). ++VER(Z038) FMID(CAL0C00) SUP(T5XD632) Applications exploiting the new z/os 1.12 dynamic allocation option to not capture the UCB during OPEN processing and have the new DEVSUPxx parmlib option NON_VSAM_XTIOT set to YES, will receive a S0C4 abend during OPEN processing for tape datasets if the UCB itself is a 31-bit UCB address. S0C4 Abend in module TMSOCEAP. Tape datasets may abend with a S0C4 during OPEN processing. Set the NON_VSAM_XTIOT option to NO in the DEVSUPxx member of SYS1.PARMLIB and reset it dynamically (SET DEVSUP=xx). PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.0 RELATED PROBLEM(S): 1975 ++IF FMID(CBAFC00) THEN REQ(RO51544). ++IF FMID(CAG8C00) THEN REQ(RO51545). ++HOLD(RO51543) SYSTEM REASON(DYNACT) FMID(CAL0C00) Re-IPL the system, or run the CAS9 procedure specifying the following parm for the CA 1 program L0C0INIT (R12.0) or L0C6INIT (R12.6) PARM(REINIT,OSI=REINIT) LOADLIB(your CA 1 load library) ).

CA 1 Tape Management 12.0 25 CA RS 1306 - PTF RO51544 12.0 RO51544 RO51544 M.C.S. ENTRIES = ++PTF(RO51544) DESC(S0C4 when DEVSUPxx NON_VSAM_XTIOT=YES). ++VER(Z038) FMID(CBAFC00) SUP(T5XD734) Applications exploiting the new z/os 1.12 dynamic allocation option to not capture the UCB during OPEN processing and have the new DEVSUPxx parmlib option NON_VSAM_XTIOT set to YES, will receive a S0C4 abend during CLOSE processing for tape datasets if the UCB itself is a 31-bit UCB address. S0C4 abend in CTSOCE00. Tape datasets may abend with a S0C4 during CLOSE processing. Set the NON_VSAM_XTIOT option to NO in the DEVSUPxx member of SYS1.PARMLIB and reset it dynamically (SET DEVSUP=xx). PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.0 CA TLMS Tape Management Release: 12.0 RELATED PROBLEM(S): 190 ++HOLD(RO51544) SYSTEM REASON(DYNACT) FMID(CBAFC00) Re-IPL the system, or run the CAS9 procedure specifying the following parm for the CA 1 program L0C0INIT (r12.0) or L0C6INIT (r12.6) or the CA TLMS program TLC0INIT (r12.0) or TLC6INIT (r12.6); PARM(REINIT,LPA=CTSOCE00) ).

CA 1 Tape Management 12.0 26 CA RS 1306 - PTF RO51545 12.0 RO51545 RO51545 M.C.S. ENTRIES = ++PTF(RO51545) DESC(S0C4 with UCB's above the line and a DCB extension). ++VER(Z038) FMID(CAG8C00) PRE(RO22249) SUP(T5XD771) An S0C4 abend may occur if a tape UCB is a 31 bit UCB address and a DCB extension is being used with new Dynamic Allocation settings that eliminate the need to create a captured UCB below the line. S0C4 Abend in module G8WTG. Both tape and non-tape allocations may abend with a S0C4 during OPEN processing. None PRODUCT(S) AFFECTED: CA 1 Tape Management Release: 12.0 CA TLMS Tape Management Release: 12.0 RELATED PROBLEM(S): 22 ++HOLD(RO51545) SYSTEM REASON(DYNACT) FMID(CAG8C00) Re-IPL the system, or run the CAS9 procedure specifying the following parm for the CA 1 program L0C0INIT (r12.0) or L0C6INIT (r12.6) or the CA TLMS program TLC0INIT (r12.0) or TLC6INIT (r12.6); PARM(REINIT,OSI=REINIT) ).