Built-in Amplifier (Medium Size) ES-A CSM_ES-A_DS_E Be sure to read Safety Precautions on page 0. Ordering Information Built-in Amplifier s Red light Infrared light Sensing method Appearance Connection method Sensing distance Functions Model NPN output PNP output --- ES-AT ES-AT Horizontal Pre-wired Timer Self Diagnosis Turbo External Diagnosis ES-AT2 ES-AT4 Through-beam s Connector (M2) 7 m --- ES-AT6 ES-AT6 --- ES-AT6 ES-AT8 Vertical Pre-wired Timer Self Diagnosis Turbo External Diagnosis ES-AT7 ES-AT9 Connector (M2) --- ES-AT66 ES-AT86 --- ES-AR ES-AR Horizontal Pre-wired Timer Self Diagnosis Turbo External Diagnosis ES-AR2 ES-AR4 Retro-reflective s Connector (M2) 2 m (00 mm) --- ES-AR6 ES-AR6 --- ES-AR6 ES-AR8 Vertical Pre-wired * Timer Self Diagnosis Turbo External Diagnosis ES-AR7 ES-AR9 Connector (M2) --- ES-AR66 ES-AR86
Sensing method Appearance Connection method Sensing distance Functions Model NPN output PNP output --- ES-AD *2 ES-AD 00 mm (wide view) Timer Self Diagnosis ES-AD2 ES-AD4 Horizontal Pre-wired 0 mm Timer Self Diagnosis --- ES-AD ES-AD Turbo ES-AD2 ES-AD4 --- ES-AD2 ES-AD2 700 mm Timer Self Diagnosis Turbo ES-AD22 ES-AD42 Diffuse-reflective s Connector (M2) 00 mm (wide view) 0 mm 700 mm ES-AD8 ES-AD8 --- ES-AD6 ES-AD6 ES-AD7 ES-AD7 --- ES-AD6 *2 ES-AD8 00 mm (wide view) Timer Self Diagnosis ES-AD7 ES-AD9 Vertical Pre-wired 0 mm Timer 700 mm Self Diagnosis --- ES-AD6 ES-AD8 Turbo ES-AD7 ES-AD9 --- ES-AD62 ES-AD82 Timer Self Diagnosis ES-AD72 ES-AD92 Connector (M2) 00 mm (wide view) 0 mm 700 mm --- ES-AD68 ES-AD66 ES-AD67 ES-AD88 ES-AD86 ES-AD87 *. Values in brackets are the minimum required distance between the and Reflector. *2. The following models are available with 0-mm sensing distances: ES-AD4 and ES-AD64. Accessories (Order Separately) Insert-type Long Slit Slit width Minimum sensing Sensing distance object (typical) 0. mm. mm 00 mm 0.2-mm dia. mm. mm. m 0.4-mm dia. 2 mm.6 mm 2. m 0.8-mm dia. Model Quantity Remarks E9-S46 of each for Emitter/ Receiver (4 Slits total) of each for Emitter/ Receiver (2 Slits total) Slits can be used with the ES- AT@@ Through-beam. Page 0 Mutual Interference Prevention Filters Sensing distance Model Quantity Remarks 2.4 m E9-E6 Reflectors/Other Accessories 2 of each for Emitter/Receiver (4 Filters total) Can be used with the ES-AT@@ Through-beam. Page Name Sensing distance (typical) Model Quantity Remarks Reflectors 2 m (00 mm) * (rated value) E9-R Provided with ES-AR@@ Retro-reflective. Small Reflectors. m (00 mm) * E9-R --- 600 mm (70 mm) * E9-R4 --- 40 mm (00 mm) * E9-RS Tape Reflectors 700 mm (00 mm) * E9-RS2 Enables MSR function. 900 mm (00 mm) * E9-RS Axis Confirmation Reflector --- E9-R Used to check optical for the ES-AT@@ Through-beam. Note: When using any Reflector other than the provided one, use a sensing distance of approximately 0.7 times the typical value as a guide. * Values in brackets are the minimum required distance between the and Reflector. 2
Mounting Brackets/Other Appearance Model Quantity Remarks E9-L69 Provided with ES-A Horizontal s. E9-L70 Provided with ES-A Vertical s. E9-L9 Provided with ES-A Vertical Pre-wired s. E9-L8 Provided with ES-A Vertical Connector s. E9-L97 E9-L98 E9-L60 Protective Cover for Horizontal s Note: When mounting s with Connectors, the I/O Connector will come into contact with the Bracket. Mount the with care. Protective Cover for Vertical s Note: When mounting s with Connectors, the I/O Connector will be longer. Mount the with care. Close Mounting Plate: Provided with ES-A Connector s. Note: If a Through-beam Model is used, order two Mounting Brackets, one for the Emitter and one for the Receiver. s I/O Connectors Model Quantity Remarks E9-G2 Provided with product. s I/O Connectors Cable Appearance Cable type Model Straight 2 m XS2F-D42-DC0-A m XS2F-D42-GC0-A Standard -wire L-shaped 2 m XS2F-D422-DC0-A m XS2F-D422-GC0-A Note: When using Through-beam models, order one connector for the Receiver and one for the Emitter.
Ratings and Specifications ES-A Item Sensing distance Sensing method Standard sensing object Model Through-beam s ES-AT, 6, 2,, 6, 4, 6, 66, 7, 8, 86, 9 7 m Opaque: 0-mm dia. min. Differential travel --- Directional angle Both Emitter and Receiver: to Retro-reflective s (with MSR function) ES-AR, 6, 2,, 6, 4, 6, 66, 7, 8, 86, 9 2 m (00 mm) * (When using E9-R) Opaque: 7-mm dia. min. *. Values in brackets are the minimum required distance between the and Reflector. *2. National Electrical Manufacturers Association ES-AD, 8, 2,, 8, 4, 6, 68, 7, 8, 88, 9 00 mm (wide view) (white paper 00 00 mm) % max. of sensing distance Diffuse-reflective s ES-AD, 6, 2,, 6, 4, 6, 66, 7, 8, 86, 9 0 to 0 mm (white paper 00 00 mm) --- 0% max. of sensing distance to 0 --- ES-AD2, 7, 22, 2, 7, 42, 62, 67, 72, 82, 87, 92 700 mm (white paper 0 0 mm) % max. of sensing distance Light source (wavelength) Red LED (700 nm) Infrared LED (880 nm) Red LED (700 nm) Infrared LED (880 nm) Power supply voltage 0 to 0 VDC, including ripple (p-p) 0% Current consumption Control output Self-diagnostic output (Only on s with self-diagnostic outputs) External diagnostic input (Only on s with external diagnostic outputs) Protection circuits Response time Input voltage Response time Sensitivity adjustment Timer function (Only on s with the timer function) Turbo function (Only on s with the turbo function) Ambient illumination (Receiver side) Ambient temperature Ambient humidity Insulation resistance Dielectric strength Vibration resistance (destruction) Shock resistance (destruction) Both Emitter and Receiver: ma max. (plus approx. ma with turbo function) 0 ma max. (plus approx. ma with turbo function) ma max. 0 ma max. (plus approx. ma with turbo function) Load power supply voltage: 0 VDC max., Load current: 00 ma max. (residual voltage: V max.) Open-collector output (NPN or PNP depending on model), Light-ON/Dark-ON selectable (Only s with self-diagnostic function) Load power supply voltage: 0 VDC max., Load current: 0 ma max. (residual voltage: V max.), Open-collector output (NPN or PNP depending on model) NPN with Emitter OFF: 0 V short-circuit or. V max. (source current: ma max.) with Emitter ON: Open (leakage current: 0. ma max.) PNP with Emitter OFF: +DC short-circuit or. VDC max. (sink current: ma max.) with Emitter ON: Open (leakage current: 0. ma max.) 0. ms max. Power supply reverse polarity protection, Output short-circuit protection Operation or reset: 0. ms max. Two-turn endless adjuster with an 0 to 00 ms OFF-delay variable adjuster --- ma max. Power supply reverse polarity protection, Output short-circuit protection, Mutual interference prevention Yes (with turbo switch) --- Incandescent lamp:,000 lx max. Sunlight: 0,000 lx max. Operating: 2 C to C (with no icing or condensation) Storage: C to 70 C (with no icing or condensation) Operating: % to 8% (with no condensation) Storage: % to 9% (with no condensation) MΩ min. at 00 VDC between current-carrying parts and case,000 VAC, 0/60 Hz for min. between current-carrying parts and case 0 to Hz,.-mm double amplitude for 2 hours each in X, Y, and Z directions Destruction: 00m/s 2, times each in X, Y, and Z directions Degree of protection IEC IP67; NEMA: 4X (indoors only) *2 Connection method Weight (packed state) Material Accessories Case Lens Mounting Bracket Pre-wired (standard length: 2 m) or M2 connector Pre-wired cable: Approx. 0 g Connector: Approx. 70 g PBT Denatured polyallylate Stainless steel Pre-wired cable: Approx. 0 g Connector: Approx. 60 g Pre-wired cable: Approx. 90 g Connector: Approx. 0 g Mounting bracket (with screws), Sensitivity adjustment driver, Sensitivity adjusting knob, Instruction sheet, Close mounting plate (only for s with connectors), and Reflector (only for Retro-reflective s) 4
Engineering Data (Typical) ES-A Parallel Sensing Range Through-beam s Through-beam s Through-beam s ES-AT@@ ES-AT@@ + E9-S46 (Slit Sold Separately) ES-AT@@ + E9-E6 (Filter Sold Separately) Distance Y (mm) 00 0 00 0 00 0 00 2 4 6 8 Distance X (m) X Y Distance Y (mm) 0 00 0 Slit width: 2 mm Y Slit width: mm X 2 4 6 7 8 Distance X (m) Distance Y (mm) 0 00 0 Y X 2 4 6 Distance X (m) 0 00 00 00 0 00 Parallel Sensing Range Retro-reflective s ES-AR@@ + E9-R (with Reflector) Slit width: 0. mm 0 0 Sensing Range Diffuse-reflective s ES-AD@/AD@2/AD@/AD@6/AD@7/AD@8 Distance Y (mm) 00 80 60 0 60 80 E9-R Reflector Y X 0..0. 2.0 2. Distance X (m) Distance Y (mm) Sensing object: white paper ES-AD@/@/@6/@8: 00 00 mm 0 ES-AD@2/@7: 0 0 mm ES-AD@/@6 0 0 0 0 0 ES-AD@/@8 0 600 800 Distance X (m) X Y ES-AD@2/@7 00 Excess Gain vs. Set Distance Through-beam s ES-AT@@ Excess gain ratio (times) 00 00 00 0 0 0 Operating level 0 7 0 Distance (m) Retro-reflective s ES-AR@@ + E9-R (with Reflector) Excess gain ratio (times) 00 0 0 0 E9-R Reflector Operating level 0 0.2 0.4 0.6 0.8.2.4.6.8 2 2.2 2.4 2.6 Distance (m)
Diffuse-reflective Diffuse-reflective Sensing Object Size vs. Sensing Distance ES-AD@/AD@2/AD@/AD@6/AD@7/ AD@8 (Detection of White Paper) ES-AD@/AD@2/AD@/AD@6/AD@7/ AD@8 (Detection of Black Paper) ES-AD@/AD@2/AD@/AD@6/AD@7/ AD@8 Excess gain ratio (times) 00 00 00 0 0 0 Sensing object: White paper ES-AD@/@/@6/@8: 00 00 mm ES-AD@2/@7: 0 0 mm ES-AD@2/@7 Excess gain ratio (times) 00 0 0 0 ES -AD@/@6 Operating level 0. ES-AD@/@8 0 0.2 0.4 0.6 0.8.2 Distance (m) Operating level 0. 0. Sensing object: Black paper ES-AD@/@/@6/@8: 00 00 mm ES-AD@2/@7: 0 0 mm ES -AD@/@6 ES-AD@/@8 ES-AD@2/@7 0. 0 0 0 600 800 Distance (mm) Distance (m).2 Sensing object: white paper 0.8 0.6 0.4 0.2 0 ES-AD@2/@7 ES-AD@/@6 ES-AD@/@8 OFF ON OFF ON OFF ON 0 0 00 00 0 0 00 00 Side of object (mm) I/O Circuit Diagrams NPN Output Model Operation mode Timing charts Mode selector switch Output circuit ES-AT ES-AT6 ES-AT6 ES-AT66 ES-AR ES-AR6 ES-AR6 ES-AR66 ES-AD ES-AD6 ES-AD6 ES-AD66 ES-AD2 ES-AD7 ES-AD62 ES-AD67 ES-AD ES-AD8 ES-AD6 ES-AD68 Light-ON Dark-ON Through-beam Emitters Light ON OFF (Between brown and black) Light ON OFF (Between brown and black) Power main circuit L Side (LIGHT ON) D Side (DARK ON) Brown Through-beam Receivers, Retro-reflective s, Diffuse-reflective s Light Stability main circuit 0 to 0 VDC ZD Connector Pin Arrangement 2 4 Note: Pin 2 is not used. Brown (Control Load output) Black (Relay) 4 00 ma max. Connector Pin Arrangement 2 4 Note: Pins 2 and 4 are not used. 0 to 0 VDC 6
Model ES-AT2 ES-AT7 ES-AD2 ES-AD7 ES-AD22 ES-AD72 ES-AD2 ES-AD7 Operation mode Light-ON Dark-ON Light ON OFF Timing charts (Between brown and black) T: OFF-delay timer (0 to 00 ms) Light ON OFF (Between brown and black) T: OFF-delay timer (0 to 00 ms) External diagnostic input Mode selector switch L Side (LIGHT ON) D Side (DARK ON) --- Emitter LED --- Indicator T T ON OFF (Between blue and pink) ON OFF ON OFF Through-beam Receivers, Diffuse-reflective s Stability Light main circuit Through-beam Emitters Power main circuit Output circuit ZD 00 ma max. 0 ma max. ZD Brown Black Load (Control (relay) output) Orange (Self-diagnostic output) Load (relay) Brown 0 to 0 VDC Pink (External diagnostic input) 0 V 0 to 0 VDC ES-AR2 ES-AR7 Light-ON Dark-ON Light ON OFF (Between brown and black) T: OFF-delay timer (0 to 00 ms) Light ON OFF (Between brown and black) T: OFF-delay timer (0 to 00 ms) T T L Side (LIGHT ON) D Side (DARK ON) Retro-reflective s Stability Light main circuit 00 ma max. ZD 0 ma max. ZD 2 K Brown Black Load (relay) (Control output) Orange (Self-diagnostic Pink Load (relay) output) (External diagnostic input) 0 to 0 VDC Structure of I/O Connector 2 4 Terminal No. 2 4 XS2F-D42-DC0-A Brown Black Classification Wire color Connection Pin No. Application Brown +V For DC --- 2 --- 0 V Black 4 Output Note: Pin No. 2 is not used. 7
PNP Output Model ES-AT ES-AT6 ES-AT8 ES-AT86 ES-AR ES-AR6 ES-AR8 ES-AR86 ES-AD ES-AD6 ES-AD8 ES-AD86 ES-AD2 ES-AD7 ES-AD82 ES-AD87 ES-AD ES-AD8 ES-AD8 ES-AD88 Operation mode Light-ON Dark-ON Through-beam Model Emitters Timing charts Light ON OFF (Between blue and black) Light ON OFF (Between blue and black) Light main circuit Mode selector switch L Side (LIGHT ON) D Side (DARK ON) Output circuit Through-beam Receivers, Retro-reflective s, Diffuse-reflective s Brown Stability Light main circuit 0 to 0 VDC ZD Brown Connector Pin Arrangement 2 4 Note: Pin 2 is not used. Black (Control output) 4 00 ma max. Load (Relay) Connector Pin Arrangement 2 4 Note: Pins 2 and 4 are not used. 0 to 0 VDC ES-AT4 ES-AT9 ES-AD4 ES-AD9 ES-AD42 ES-AD92 ES-AD4 ES-AD9 Light ON Dark ON Light ON OFF (Between blue and black) T: OFF-delay timer (0 to 00 ms) Light ON OFF (Between blue and black) T: OFF-delay timer (0 to 00 ms) T T L Side (LIGHT ON) D Side (DARK ON) Through-beam Receivers, Diffuse-reflective s Stability Light main circuit Through-beam Emitters ZD ZD 00 ma max. Brown Orange 0 ma max. (Control output) Black Load (relay) (Self-diagnostic output) Load (relay) 0 to 0 VDC External diagnostic input --- Emitter LED --- Indicator ON OFF (Between brown and pink) ON OFF ON OFF Power main circuit Brown 0 to 0 VDC Pink (External diagnostic input) 0 V 8
Model Operation mode Timing charts Mode selector switch Output circuit ES-AR4 ES-AR9 Light-ON Dark-ON Light ON OFF (Between blue and black) T: OFF-delay timer (0 to 00 ms) Light ON OFF (Between brown and black) T: OFF-delay timer (0 to 00 ms) T T L Side (LIGHT ON) D Side (DARK ON) Retro-reflective s Stability Light main circuit 4.4 K ZD ZD 0 ma max. 00 ma max. Brown Pink Orange (External diagnostic input) (Self-diagnostic output) (Control output) Load Black (relay) Load (relay) 0 to 0 VDC Structure of I/O Connector 2 4 Terminal No. 2 4 XS2F-D42-DC0-A Brown Black Classification Wire color Connection Pin No. Application Brown +V For DC --- 2 --- 0 V Black 4 Output Note: Pin 2 is not used. Adjustment Methods Sensitivity Adjustment for Diffuse-reflective s Set to Light ON Item Sensing condition Sensitivity adjuster Indicators Procedure ) Position A 2) Position B Sensing object Sensing object ) Setting --- Background object Background object (A) Min. Min. (A) Min. Max. Max. (C) (C) (B) Max. ON OFF Stability ON OFF Stability OFF ON Light ON OFF Light Locate a sensing object at the sensing distance, set the sensitivity adjuster to the minimum scale position, and gradually increase sensitivity by turning the sensitivity adjuster clockwise until the incident light (red LED) is ON. Position A is where the has turned ON. Position B is when the sensing object is removed and the sensitivity adjuster is turned clockwise until the incident light (red LED) is ON. Position C is where the adjuster is turned counterclockwise (reducing the sensitivity) from position B until the incident light (red LED) is OFF. When there are no background objects, the maximum sensitivity is position C. Set the sensitivity adjuster to halfway between (A) and (C) (at the optimum sensitivity). Check that the stability (green LED) turns ON according to whether the sensing object is there or not. There is not sufficient margin if it does not turn ON. If this is the case, reconsider the detection method. Unlike conventional s, the variation in the sensitivity of ES-A s is minimal. This means the sensitivity can be adjusted on only a single, and then the adjusters on the other s can be set to the same scale position. There is no need to adjust the sensitivity of each individually. ON Stability ON OFF Light 9
Safety Precautions WARNING This product is not designed or rated for ensuring safety of persons. Do not use it for such purposes. Precautions for Correct Use Do not use the product in atmospheres or environments that exceed product ratings. Mounting Position of Axis of Through-beam Model Unlike conventional through-beam sensors, the ES-A Through-beam incorporates 2 lenses. The lens actually in use is the one marked with an arrow indicating the position of the optical. When using a Slit, attach it to the lens marked with the arrow. Mounting Bracket (Provided) The direction of the optical coincides with the machine of the ES-A when the mounting screw is inserted into the lock hole of the Mounting Bracket. If the mounting surface and the screw hole are correctly aligned toward the sensing object (or toward the Retroreflector for a Through-beam ), the mechanical and optical will be aligned when the screw is inserted into the hole. will be detected, and time-consuming adjustment will not be necessary. (If, however, the mounting surface is not flat, adjustment of the optical may still be required.) Adjust the position of the so that incident light points at the center. Make sure that the incident light is at a fixed position. The maximum tightening torque of the screw is 0. N.m max. Unused lens arrow Arrow indicating optical position Lens actually in use (attach the Slit to this lens) Machine Base of mounting bracket Bracket can move in this direction lock hole (M) Position of Arrow Indicating Axis Model ES-A (Vertical s) ES-A (Horizontal s) Position of lens in use Top Bottom Tightening the Connector Manually tighten the connector until the threads have completely disappeared. If tightening is insufficient, the degree of protection may not be maintained, or the connector may become loose when it is subjected to vibration. Using pliers to tighten the connector may damage it. Adjustments E9-S46 Through-beam Slits (Accessory, order separately) Use the rubber attachment with the metal cover if a slit width of 2 mm is required. (A Slit is not required in this case.) Insert the 0.- or -mm Slit between the metal cover and rubber attachment if a slit width of 0. or mm is desired. These Slits fit into the rubber attachment..6 mm 2 mm Metal cover Slit (0. mm or mm) Rubber attachment Arrow indicating. mm position of optical Screw Indented portions Use the E9-L60 Close Mounting Plate (provided) if the is mounted using mounting brackets or if it is mounted directly. (Refer to Dimensions.) ES-A Apply the Slit to the lens of the marked with an arrow indicating the position of the optical (apply it to the bottom lens of Horizontal s and the top lens of Vertical s). 0
E9-E6 Polarized Mutual Interference Prevention Filters for Through-beam s (Accessory, order separately) A set of 4 Filters are sold together for two Through-beam s (for 2 each for Emitters and Receivers). Order one for every two sets of s. For mounting, refer to the figure of the Through-beam Slits. Receiver Y = 0 Emitter Up to two units can be attached. Note: The arrows on the Filters can be attached in either direction when two s are mounted next to each other. The Filter attached to an Emitter and to the corresponding Receiver must be the same in direction of polarization or the will not function. The arrow printed on the cover indicates the direction of polarization. By attaching the Filters opposite to each other in polarization to the Emitters and the Receivers in rows, mutual interference can be prevented (in any case, the Filter attached to an Emitter and to the corresponding Receiver must be the same in direction of polarization or the will not function). Operating Mode Selection As shown in the following illustration, the ES-A has an operating mode selector on the panel where the Receiver connector is located. With this operating mode selector, the ES-A is in either Dark- ON or Light-ON mode. Operating mode switch (black) Light ON Dark ON (ON when light is ON) (ON when light is OFF) D L Turbo Function ( Turbo Switch) The turbo function is effective with the turbo switch pressed, and the function is reset automatically when released. With the turbo function switched ON, the light spot is visible even at a distance of 0 mm, making it easy to check the sensing position and the angle of the optical. Precautions ()Do not keep the turbo switch pressed for longer than minutes. (It will not break even if it is pressed for an extended period.) (2)Pressing the switch may change the timer delay settings. Set the timer after using the turbo function to check the optical. ()To press the switch, use a force of 9.8 N max. Sensitivity adjuster The OFF-delay timer adjuster is used as a turbo switch (black). The intensity of the red spot will be increased, making visual confirmation much easier. PUSH Using the E9-R Axis Reflector for Throughbeam s (Accessory, order Separately) Use this attachment when the set distance is long and adjustment is mechanically difficult with a sensing object. Eye ES-AT@@ Receiver E9-R Axis Confirmation Reflector The default operating mode is shown in the following table. Default switch Sensing method setting Through-beam s Dark-ON Retro-reflective s Diffuse-reflective s Light-ON Timer and Turbo Switch The Emitter of the Through-beam with the selfdiagnostic feature incorporates a turbo switch. When this switch is ON, the intensity of the red LED light source can be increased to make a brighter spot. ES-AT@@ Emitter Attach the Reflector to the Receiver. Look at the Reflector from right behind the Emitter. The Reflector should be bright with red light when the optical beam strikes the Reflector. If the Emitter has a turbo function, the Reflector looks brighter with the function switched ON. When the Reflector is removed, the light beam strikes the Receiver.
Dimensions (Unit: mm) Unless otherwise specified, the tolerance class IT6 is used for dimensions in this data sheet. ES-A Built-in Amplifier Through-beam s (Horizontal) Pre-wired s ES-AT/2//4 (Receiver) 28.9 6.9 Sensitivity adjuster (white) Timer adjuster (black) * Light (4). 2.9 7 2.4 2 4-dia. vinyl-insulated round cable with 4 conductors (Conductor cross section: 0.2 mm 2, Insulator diameter:. mm), Standard length: 2 m *2 8.8 dia. Emitter: ES-AT@@-L Receiver: ES-AT@@-D 0. 0. Stainless steel Lens (7 7) *. Not applicable to s with timer adjusters (ES-AT and ES-AT). *2. The ES-AT or ES-AT has three conductors.. Stability Operation mode selector switch 2 8. 0. Two, M holes ES-AT/ (Emitter) 7.8 Power (4) 4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.2 mm 2, Insulator diameter:. mm), Standard length: 2 m 28.9 6.9 2.4 2 8.8 dia.. 0. 0 Stainless steel Lens (7 7). 2 8. 0. ES-AT2/4(Emitter) Power 2.4 2 2.9 2. Turbo switch (4) 4-dia. vinyl-insulated round cable with conductors (Conductor cross section: 0.2 mm 2, Insulator diameter:. mm), Standard length: 2 m 8.8 dia. 0. 28.9 6.9. Two, M holes 0. 0 2
s with Standard Connectors ES-AT6/6 (Receiver) 28.9 6.9 2.4 Sensitivity adjuster (white) Light M2 Connector (0) 2.9 7 2. Stability 0.. Stainless steel Lens (7 7). Operation mode selector switch 2 8. 0. Two, M ES-AT6/6 (Emitter) Power M2 Connector 7.8 (0) 2.4 2 28.9 6.9. 0.. Stainless steel 2 Lens (7 7). 8. 0. Two, M
Through-beam s (Vertical) Pre-wired s ES-AT6/7/8/9 (Receiver) 8. Lens (7 7). (4) 4-dia. vinyl-insulated round cable with 4 conductors (Conductor cross section: 0.2 mm 2, Insulator diameter:. mm), Standard length: 2 m * 28.9 6.9 Stainless steel 2.4 2 8.8 dia...4. Stability.6 7 Light Sensitivity adjuster (white) Timer adjuster (black) *2. Operation mode selector switch 4 2. 0. *. The ES-AT6 or ES-AT8 has three conductors. *2. Not applicable to timer adjuster models ES-AT6 and ES-AT8. Two, M holes 0. Two, M x 2 screws ES-AT6/8 (Emitter) 8. Lens (7 7). (4) 4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.2 mm 2, Insulator diameter:. mm), Standard length: 2 m * 28.9 6.9 Stainless steel 2.4 2 8.8 dia....4 Power. 4 8. 2 0. ES-AT7/9 (Emitter) 0. Power.6 Turbo switch 2 2. *The ES-AT7 of ES-AT9 has three conductors. Two, M holes 4
Connector s ES-AT66/86 (Receiver).4 9.4 8. Use these two holes for mounting. 2 Lens (7 7). M2 Connector (0). Stainless steel 4.7.4 2 Stability.6 7 LIght Sensitivity adjuster (white). Operation mode selector switch E9-L60 Close Mounting Plate (provided) (Attach the mounting plate or the plug cannot be connected.) 0. 0. Two, M holes ES-AT66/86 (Emitter).4 9.4 8. Use these two holes for mounting. 2 Lens (7 7). M2 Connector (0). Power. Stainless steel 4.7.4 2 8. 0. Two, M holes E9-L60 Close Mounting Plate (provided) (Attach the mounting plate or the plug cannot be connected.) 0.
Retro-reflective s (Horizontal) Pre-wired s ES-AR/2//4 28.9 6.9 0. 0. Stainless steel Lens (7 4) Light 2.4 2.2 2. 42.. 7 (4) *2 *. For ES-AR2 and ES-AR4 only. *2. 9.7 mm for ES-AR2 and ES-AR4. *. The ES-AR or ES-AR has three conductors. Receiver. Stability Sensitivity adjuster (white) Timer adjuster/ Turbo switch (black) * Turn to adjust the timer: push to switch turbo function 4-dia. vinyl-insulated round cable with conductors (Conductor cross section: 0.2 mm 2, Insulator diameter: 8.8 dia.. mm), Standard length: 2 m * Operation mode selector switch 9 2. Emitter 2.8 Two, M holes s with Connectors ES-AR6/6 28.9 6.9 Light.2 2. 2.4 2 Sensitivity adjuster (white) 42. (0) Connector M2 7. Stability. 0 Stainless steel Lens (7 4) Receiver. Operation mode selector switch 2. 9 Emitter 2.8 Two, M holes 6
Retro-reflective s (Vertical) Pre-wired s ES-AR6/7/8/9 28.9 6.9 4.8 Stainless steel Receiver Lens (.7 0.9) 2.4 2 7 Emitter (4) *2 4-dia. vinyl-insulated round cable with conductors (Conductor cross section: 0.2 mm 2, Insulator diameter:. mm), Standard length: 2 m * 8.8 dia...4 4. Stability 2..9 7. Light Sensitivity adjuster (white). Operation mode selector switch. Timer adjuster/ Turbo switch (black) * Turn to adjust the timer: push to switch turbo function 0. *. Available on ES-AR7 and ES-AR9 only. *2. 9.7 mm for ES-AR7 and ES-AR9. *. The ES-AR6 or ES-AR8 has three conductors. 0. Two, M holes s with Connectors ES-AR66/86.4 9.4 4.8 Use these two holes for mounting. Receiver Lens (.7 0.9) 2 7 Emitter M2 Connector (0) Stainless steel 4.7..4 Four mounting holes 2. Stability.9 7 Light Sensitivity adjuster (white). Operation mode selector switch. 0. Two, M 2 screws Two, M holes E9-L60 Close Mounting Plate (provided) (Attach the mounting plate or the plug cannot be connected.) 0. 7
Diffuse-reflective s (Horizontal) Pre-wired s ES-AD/2//2/22/2 -AD/2//4/42/4 Light 2.9 7. 2.4 2 Sensitivity adjuster (white) Timer adjuster/ Turbo switch (black) * Turn to adjust the timer: push to switch turbo function (4) 4-dia. vinyl-insulated round cable with 4 conductors (Conductor cross section: 0.2 mm 2, Insulator diameter:. mm), Standard length: 2 m *2 8.8 dia. 28.9 6.9 0. 0. Stainless steel *. Timer adjuster: Not available on ES-AD, ES-AD2, ES-AD, ES-AD, ES-AD2 and ES-AD. Turbo switch: Available on ES-AD2 and ES-AD4 only. *2. The ES-AD, ES-AD2, ES-AD, ES-AD, ES-AD2, or ES-AD has three conductors. Lens (7 4) Receiver. Stability Operation mode selector switch 9 2. Emitter 0. Two, M holes s with Connectors ES-AD6/7/8/6/7/8 Sensitivity adjuster (white) Light M2 Connector (0) 2.9 7 28.9 6.9 2.4 2. Stability. 0 Stainless steel Lens (7 4) Receiver. Operation mode selector switch 2. 9 Emitter 0. Two, M holes 8
Diffuse-reflective s (Vertical) Pre-wired s ES-AD6/62/6/7/72/7 -AD8/82/8/9/92/9 4.8 Receiver Lens (7 4) 2.4 2 7 Emitter (4) 4-dia. vinyl-insulated round cable with 4 conductors (Conductor cross section: 0.2 mm 2, Insulator diameter:. mm), Standard length: 2 m * 8.8 dia. 28.9 6.9..4 4 Stainless steel. Stability 2.6 7. Light Sensitivity adjuster (white) Timer adjuster/ Turbo switch (black) *2 Turn to adjust the timer: push to switch turbo function. 0. Operation mode selector 0. *. ES-AD6, ES-AD62, ES-AD6, ES-AD8, ES-AD82, and ES-AD8 have three conductors. *2. Timer adjuster: Not available on ES-AD6, ES-AD62, ES-AD6, ES-AD8, ES-AD82 and ES-AD8. Turbo switch: Available on ES-AD7 and ES-AD9 only. Two, M holes s with Connectors ES-AD66/67/68/86/87/88.4 9.4 4.8 Use these two holes for mounting. Receiver Lens (7 4) 2 7 Emitter Connector M2 (0) Stainless steel 4.7..4 Stability 2.6 7 Light Sensitivity adjuster (white). Operation mode selector switch 0. Two, M holes E9-L60 Close Mounting Plate (provided) (Attach the mounting plate or the plug cannot be connected.) 0. 9
Accessories (Order Separately) Insert-type Long Slit (For Through-beam Model) E9-S46.6 A 2. 6.8 Filters for Mutual Interference Prevention (For Through-beam Model) E9-E6 9.7.6 6.8 2.4.6 A 2.4 A * Name Dimensions A Material Quantity Supporter Slits 2 mm 0. mm mm Stainless steel PVC One each for Emitter and Receiver (total of 2) One each for Emitter and Receiver (total of 4) Material: Stainless steel * Two of each for the Emitter and Receiver (total of four) 2. Axis Confirmation Reflector (For Through-beam Model) E9-R Bracket to be attached to the Emitter panel of ES-A.9 9.7.7 Reflectors Mounting Brackets 7.9.6 9.9 2.2 Material: Reflector: Acryl Back: ABS.9 7. In the interest of product improvement, specifications are subject to change without notice.