Grass TEC Face Frame Hinge System for tec The star in your cabinet
Grass TEC Technical Features How to Specify TEC Hinges There are numerous variables that will determine the choice of hinge. Determine the requirements of the application. C onsider the following points based on the door to cabinet application. 1 3 4 6 7 8 9 10 Door overlay Adjustment requirements: a. Height only b. Height and side c. Height, side and depth Baseplatemountingtofaceframe: a. Wrap-around - 3 4 thickframesonly b. S ide mount - frames thicker than 3 4 c. Face mount - any overlay greater than 1 3 8 d. MDF material - mounting into end grain Door removal: a. With base plate mounting screw (one-piece hinges) b. With depth adjustment screw (two-piece hinges) Door clearance/hinge arm clearance (for interior rollout trays) Door gap - distance between face frame and the back of the closed door Minimum reveal - distance between two doors hinged back-to-back Door thickness - thicker doors can restrict opening angle and minimum reveal Hinge cup boring pattern for dowelled hinges Door opening angle All-steel Construction TEC hinges feature a solid metal hinge cup. All moving mechanism parts, including pivot pins, linkages and springs are hardened to ensure long-term durability. S hallow C up Depth TEC hinges feature a shallow 10.mm [ 13 3 ] cup to accommodate profiled door edge. AC C 140 hinges have a 10mm [ 13 3 ] cup depth. B HMA Grade S pecifications TEC hinges meet and surpass ANSI/BHMA Grade specifications. All products are tested by an independent testing lab. Grass Warranty Limited Lifetime Warranty against defects in material and workmanship for as long as the original consumer owns the product. Hinge Adjustment Chart Number of Hinges Per Door The number of hinges required depends on the size and weight of the door. The distance between the hinges should be spaced as wide as possible. Use the diagram to determine the number of hinges needed. These recommendations are for doors without accessory attachments. Hinge Height Side Depth 864 Small Overlay 864 Large Overlay 86 Face Mount 861 861 Square Hole 861 MDF ACC 140 Decrease overlay with optional spacer.
Grass TEC Contents Introduction Description 108 Opening Angle - 1 4 to1 Overlay 4- One-piece construction Page Benefits & 1 4-1 Installation 108 Opening Angle - 1 1 4 to1 1 Overlay 6-7 One-piece construction 1 1 4-1 1 3
Grass 108 Opening Angle - 1 4 to1 Overlay Face Frame Hinges with 3-dimensional Adjustment One piece hinge and base plate combination For door thickness of up to 3 4 Front locating tabs position hinge on face frame Micro side adjustment Cam depth adjustment Height adjustment at mounting screw VS = Screw-on cup, 4mm pattern VS8 = Dowelled cup, 4mm pattern VS8-4 = Dowelled cup, 4mm pattern S ide-mount - 4mm drilling pattern 6 [ 1 4 ] 11 [ 7 16 ] 14. [ 9 16 ] 864VS8 (08-01) 03044-1 300 864VS (08-01) 03046-1 300 1 [ 1 ] 3. [ 1 8 ] 11 [ 7 16 ] 864VS8 (8-01) 0304-1 300 864VS (8-01) 0306-1 300 19 [ 3 4 ] 0 11 [ 7 16 ] 864VS8 (83-01) 0960-1 300 864VS (83-01) 096-1 300 [1 ] 0 11 [ 7 16 ] 864VS8 (37-01) 0944-1 300 864VS (37-01) 0946-1 300 Wrap-around - 4mm drilling pattern 6 [ 1 4 ] 11 [ 7 16 ] 14. [ 9 16 ] 864VS8 (08-0) 098-1 300 864VS (08-0) 0930-1 300 1 [ 1 ] 3. [ 1 8 ] 11 [ 7 16 ] 864VS8 (8-0) 094-1 300 864VS (8-0) 096-1 300 19 [ 3 4 ] 0 11 [ 7 16 ] 864VS8 (83-0) 096-1 300 864VS (83-0) 098-1 300 [1 ] 0 11 [ 7 16 ] 864VS8 (37-0) 09-1 300 - - - S ide-mount - 4mm drilling pattern Overlay Door Clearance Arm Clearance Dowelled Hinge Cup 6 [ 1 4 ] 11 [ 7 16 ] 14. [ 9 16 ] 864VS8-4 (08-01) 0304-1 300 1 [ 1 ] 3. [ 1 8 ] 11 [ 7 16 ] 864VS8-4 (8-01) 030-1 300 [1 ] 0 11 [ 7 16 ] 864VS8-4 (37-01) 094-1 300 Wrap-around Wrap-around - 4mm drilling pattern Overlay Door Clearance Arm Clearance Dowelled Hinge C up 11 [ 7 16 ] [ 3 16 ] 11 [ 7 16 ] 864VS8-4 (77-0) 099-1 300 1 [ 1 ] 3. [ 1 8 ] 11 [ 7 16 ] 864VS8-4 (8-0) 09-1 300 19 [ 3 4 ] 0 11 [ 7 16 ] 864VS8-4 (83-0) 097-1 300 [1 ] 0 11 [ 7 16 ] 864VS8-4 (37-0) 091-1 300 4 Side-mount IMPORTANT To determine the correct application, Grass strongly recommends a trial mounting for all hinges and base plates. Dimensions in millimeters, fractional inch equivalents as noted.
Technical Specifications Dimensions - Door Closed Minimum Reveal Door Open - Clearances Introduction 4.9 [3/16 ] Door Thickness Overlay 10. #8 x 3/4 pan head screw Min. Reveal Arm Clearance 108 8. [11/3 ] Door Clearance Maximum Door Thickness 19 [3/4 ] Benefits & 1 4-1 Installation Minimum Reveal Arm and Door clearances see Page 6. Door Thickness 16 [ 8 ] 17.[ 11 16 ] 19 [ 3 4 ] Minimum Reveal 4. [ 3 ].4 [ 7 3 ] 6.7 [ 1 4 ] Adjustment Details Basedondoorwithsquareedge. 1 1 4-1 1 1 Side Adjustment...+/-1.mm [ 1 16 ] R otate micro screw. Height Adjustment...+/-mm [ 3 3 ] Loosen screw, align door, tighten screw. 3 Depth Adjustment...out mm [ 3 3 ], in.mm [ 1 3 ] R otate cam screw. Mounting Screws Hinge cup to door, #6 x 8 Flatheadscrew Base plate to face frame, #8 x 3 4 Pan head screw Overall Dimensions 4mm drilling pattern 4mm drilling pattern [3/16 ] 11 10 7 [9/3 ] 39 [1 9/16 ] 7 [ 1/4 ] Ø3 4 [1 1/3 ] [/16 ] Ø3 4 [1 /3 ] [/16 ] Subject to technical modifications without notice. U.S. Patent #s 6,647,91 and,604,96
Grass 108 Opening Angle - 1 1 4 to1 1 Overlay Face Frame Hinges with 3-dimensional Adjustment One-piece hinge and base plate combination For door thickness of up to 3 4 Front locating tabs position hinge on face frame Cam side adjustment Cam depth adjustment Height adjustment at mounting screw VS = Screw-on cup, 4mm pattern VS8 = Dowelled cup, 4mm pattern VS8-4 = Dowelled cup, 4mm pattern S ide-mount - 4mm drilling pattern 3 [1 1 4 ] 0 10 [ 13 3 ] 864VS8 (31-01) 03048-1 300 864VS (31-01) 0300-1 300 3 [1 3 8 ] 0 10 [ 13 3 ] 864VS8 (16-01) 03086-1 300 864VS (16-01) 03088-1 300 38 [1 1 ] 0 10 [ 13 3 ] 864VS8 (33-01) 03098-1 300 864VS (33-01) 03100-1 300 Wrap-around - 4mm drilling pattern 3 [1 1 4 ] 0 10 [ 13 3 ] 864VS8 (31-0) 093-1 300 864VS (31-0) 0934-1 300 3 [1 3 8 ] 0 10 [ 13 3 ] 864VS8 (16-0) 0936-1 300 864VS (16-0) 0938-1 300 38 [1 1 ] 0 10 [ 13 3 ] 864VS8 (33-0) 0940-1 300 864VS (33-0) 094-1 300 S ide-mount - 4mm drilling pattern Overlay Door Clearance Arm Clearance Dowelled Hinge C up 3 [1 1 4 ] 0 10 [ 13 3 ] 864VS8-4 (31-01) 03049-1 300 3 [1 3 8 ] 0 10 [ 13 3 ] 864VS8-4 (16-01) 03087-1 300 38 [1 1 ] 0 10 [ 13 3 ] 864VS8-4 (33-01) 03099-1 300 Wrap-around - 4mm drilling pattern Overlay Door Clearance Arm Clearance Dowelled Hinge C up Wrap-around Side-mount 3 [1 1 4 ] 0 10 [ 13 3 ] 864VS8-4 (31-0) 0933-1 300 3 [1 3 8 ] 0 10 [ 13 3 ] 864VS8-4 (16-0) 0937-1 300 38 [1 1 ] 0 10 [ 13 3 ] 864VS8-4 (33-0) 0941-1 300 6 IMPORTANT To determine the correct application, Grass strongly recommends a trial mounting for all hinges and base plates. Dimensions in millimeters, fractional inch equivalents as noted.
Technical Specifications Dimensions - Door Closed Minimum Reveal Door Open - Clearances Introduction 4.9 [3/16 ] Door Thickness Overlay 10. #8 x 3/4 pan head screw Min. Reveal Arm Clearance 108 6. [1/4 ] Benefits & 1 4-1 Installation Minimum Reveal Arm and Door clearances see Page 8. Door Thickness 16 [ 8 ] 17.[ 11 16 ] 19 [ 3 4 ] Minimum Reveal 4. [ 3 ].4 [ 7 3 ] 6.7 [ 1 4 ] Adjustment Details Basedondoorwithsquareedge. 1 1 4-1 1 1 Side Adjustment...+/-1.mm [ 1 16 ] R otate cam screw. Height Adjustment...+/-mm [ 3 3 ] Loosen screw, align door, tighten screw. 3 Depth Adjustment...out mm [ 3 3 ], in.mm [ 1 3 ] R otate cam screw. Mounting Screws Hinge cup to door, #6 x 8 Flatheadscrew Base plate to face frame, #8 x 3 4 Pan head screw Overall Dimensions 4mm drilling pattern 4mm drilling pattern [ 3 /16 ] 11 10 [ 3 /8 ] 6. [ 1 /4 ] 39 [1 9 /16 ] 7 [ 1 /4 ] Ø3 4 [1 1/3 ] [/16 ] Ø3 4 [1 /3 ] [/16 ] Subject to technical modifications without notice. U.S. Patent #s 6,647,91 and,604,96 7