Program Operate Monitor Motor Controller General Creep DP Drive profiles System Actuators* Veer Comp Fwd Veer Comp Rev Latch speed step Soft stop Brake Parameters Enable encoders Dir Act SW1 Dir Act SW2 Drive Fences Attendant Override Long mode command Forward Speed Reverse speed Turning speed Attendant DP Forward Speed Reverse speed Turning speed Forward accel Reverse accel Forward decel Reverse decel Turning accel Turning decel # of DP Input device Forward Speed Reverse speed Turning speed Forward accel Reverse accel Forward decel Reverse decel Turning accel Turning decel Latch Latch mode^ Power Limit High Speed Torque Low Speed Torque Auto mode enable Templates Joystick slow Joystick Indoor Joystick Moderate Joystick Fast Joystick Climbing Switch forward only Switch learner Switch indoor Switch moderate Switch fast ^ when latch enabled Auto mode time out Latch time out on Sleep time Turn off time Shutdown to off time Horn volume Command beep Beep volume Backup alarm Keyless lock Language X active band Y active band Latched Rehome Actuators (#) Enable Assign function Input dir swap Limit count up Limit count down Speed Accel Lockout count * < 2 power seat functions if > 2 functions see QR MAC
Program Operate Monitor Handcontrol Attd Joystick Enhanced Display Joystick calibration Sensitivity Neutral Horizontal Neutral vertical Switch operation Second Fxn Command^ Assign direction Adjust throw ^ handcontrol only ** Caution: IR settings Contrast Backlight Backlight timer Units Trip Reset: Reset on charge, Reset now Icon Menus Auto scroll mode n/y Auto scroll speed Attendant level User level Manual scroll start Manual scroll speed IR factory reset**
Program Operate Monitor SCM1 Input device Input device Proportional Switches Sip & Puff S&P cals SCM1 SCM2 4 switch 3 switch 2 switch 1 switch 4d 1 switch 8d S&P 4 pressure S&P 2 pressure S&P 2 switch 4D prop 3D prop Joystick calibration re-assign joystick Adjust throw Neutral horizontal Neutral vertical Sensitivity Dir Toggle Time Toggle manual Assign Drv Sw Dir Toggle Time Toggle manual Escape Menu Step sequence Scan dwell time Escape Menu Calibrate pressure Swap Sip & Puff S&P command time Mode switch cfg db -9 switch type Jack switch type Act L/R ctrl yes/no RIM ^ with 3 switch systems enable/disable Command timing (use with switch systems) Short cmd time Between time
Program Operate Monitor QMAC -2* ECM1 System Latched Assign hex switch Re-home Inhibit set up Creep angle Lockout angle Recline Enabled Input dir swap Speed Accel Max limit Min limit Backrest limit Recline w/ Legrests Enhanced Recline Enable ER Pre-Tilt Angle Tilt Lift Leg rests Enabled Input dir swap Speed Accel Max limit Min limit Shear * Used with > 2 power seat functions Shear Program Enable Tuning Factor Module ID ECM1 ECM2 Channel1 Enable Ch1 Relay 1 Mode Relay 2 Mode Relay 3 Mode Relay 4 Mode Relay 5 Mode ECM Voltage Output off/on Diagonal Option yes/no Channel1 Enable Ch2 Relay 6 Mode Relay 7 Mode Relay 8 Mode Relay 9 Mode
Program Operate Monitor Motor IR & V current voltage Ohms RPM Channel1 Relay 1 Relay 2 Relay 3 Relay 4 Relay 5 Stereo Jack Motor Controller Brakes current voltage ECM 1 Channel2 Relay 6 Relay 7 Relay 8 Relay 9 Power seat Functions (tilt, recline)* counts current *if < 2 seat functions SCM 1 Switches S&P pressure Battery Battery voltage Battery SOC System Enhanced Display Contrast Backlight Timer Backlight Status Others Time On Time Drive Int C / box temp J/S 3-Button J/S 7- Button Attd Joystick JS position Buttons/Sw QMAC Actuators Tilt Recline Enhanced Recline Left Legrest Right Legrest Inhibit/Anti-Tip Hex Switch
Program Operate Monitor Motor Controller SCM, ECM Hand control Programmer Clear module faults Invalid system configuration error Active input not neutral at power on Left drive motor open circuit Right drive motor open circuit Left brake open circuit Right brake open circuit Left brake over current Right brake over current Battery voltage low warning Battery voltage high warning Battery under voltage Battery over voltage MCM high temp Actuatator 1 over current Actuator 2 over current Loss of communication error Internal module error No application code Clear module faults Loss of communication Internal module error No application code Clear all faults * Only current and past faults will appear
Program Operate Monitor Powered Seating IR Control Drive Profiles ECM Misc ED Misc Recline Up/Down Recline Tilt Up/Down Tilt Elevate Up/Down Elevate Left leg Up/Down Left Legrest AV Control^ ECU Control^ Drive Profile 1 Drive Profile 2 ^ select specific function with right command and highlight prior to assigning Drive Profile 3 Drive Profile 4 Drive Profile Up Drive Profile Dwn Channel 1^ Channel 2^ ^ select specific function with right command and highlight prior to assigning Sleep Mode Horn Speed Up Speed Down Backlight On/Off Contrast Trip Reset To ASSIGN buttons or jack ports : highlight above function and press square button on HHP then follow onscreen instructions