Universal Compact Extruded Cylinders Clippard s new Compact, Extruded Body Cylinders are available in double acting, double rod, single acting spring return, and single acting spring extended models. Universally compatible, they are lightweight, small in size, and provide a reliable, long cycle life. The various mounting configurations, many bore sizes, stroke lengths and other valuable options, make this the most versatile and interchangeable cylinder line in the world. Combined with Clippard s long-standing history of quality products, outstanding service and fast delivery, these cylinders are an ideal solution for your pneumatic actuation needs. SPECIFICATIONS 7 bore sizes Superior service with quick delivery Metric or imperial ports available Multiple mounting options Low profile GMR sensor slides into groove within the cylinder Available with magnetic pistons Custom strokes welcomed Interchangeable design allows for quick drop-in replacements Bumpers standard Medium Maximum Pressure Strokes Port Thread Temperature Range Mounting Material Piston & Head Seals Rod Seal/Wiper Bumpers Air 150 psig (10 bar) 1/8 to 4 (5 to 100 mm) M5 x 0.8, #10-32, G1/8, 1/8 NPT, G1/4, and 1/4 NPT 14 to 140 F (-10 to 60 C) Threaded or Thru Holes Aluminum, Stainless Steel Nitrile Polyurethane Nitrile Wear bands standard On 32 mm double rod models and all 40 mm and 50 mm models Available with Auto Switch (magnet) For position sensing Bumpers More details and a PDF catalog available online at clippard.com/link/ext-tds Self-lubricating bearing Available on larger models Wiper/rod seal Chrome-plated 303 stainless steel rod Female rod threads standard Male rod threads available High strength aluminum piston Clear anodized aluminum body Magnetic sensor tracks Standard on Auto Switch models Threaded or thru hole mounting Wrench flats To aid in installation
FORCE FACTOR FORCE The force required, operating air pressure and cylinder bore are all factors that must be determined or known when sizing an air cylinder. If two are known, the other is easily calculated using the formulas below. Area is derived using either of the following formulas: Diameter 2 x 0.7854 or Radius 2 x π F - Force or load (lbs.) P - Pressure A - Area of cylinder (in 2 ) F = P x A P = F A A = F P The force factor is the nominal area of the cylinder bore size. The chart shown at right provides forces in both the extend and retract stroke of all available bore sizes. The force factor (in 2 ) multiplied by the air pressure (psi) gives the nominal force (lbs.) produced by the cylinder. FORCE FACTOR Bore Direction Pressure 12 mm Extend 1.1 bar 0.2 psig Retract 0.8 bar 0.1 psig 16 mm Extend 2.0 bar 0.3 psig Retract 1.5 bar 0.2 psig 20 mm Extend 3.1 bar 0.5 psig Retract 2.4 bar 0.4 psig 25 mm Extend 4.9 bar 0.8 psig Retract 3.8 bar 0.6 psig 32 mm Extend 8.0 bar 1.2 psig Retract 6.0 bar 0.9 psig 40 mm Extend 12.6 bar 1.9 psig Retract 10.6 bar 1.6 psig 50 mm Extend 19.6 bar 3.0 psig Retract 16.5 bar 2.6 psig Power Factor x bar = kg, Power Factor x psig = pounds SPRING FORCES (lbs.) - Compressed / At Rest Bore 5 mm Stroke 10 mm Stroke 15 mm Stroke 20 mm Stroke 25 mm Stroke 30 mm Stroke 12 mm 1.8 / 1.3 1.8 / 0.8 1.7 / 0.8 1.7 / 0.5 16 mm 4 / 3.5 4 / 2.5 4 / 3 4 / 3 20 mm 5.5 / 4 5.5 / 2.5 5.5 / 4 5.5 / 3.5 5.5 / 3 5.5 / 2.5 25 mm 7 / 6 7 / 5 6.5 / 5 6.5 / 4.5 6.5 / 4 6.5 / 3.5 32 mm 13 / 11 13 / 10 11 / 9 11 / 8.5 11 / 7.5 11 / 7 40 mm 17 / 14 17 / 11 17 / 14 17 / 12 17 / 11 17 / 10 50 mm 22 / 19 22 / 15 23 / 19 23 / 17 23 / 16 23 / 15 Bore 1/8 Stroke 1/4 Stroke 3/8 Stroke 1/2 Stroke 5/8 Stroke 3/4 Stroke 7/8 Stroke 1 Stroke 12 mm 1.8 / 1.5 1.8 / 1.2 1.8 / 0.9 1.7 / 0.9 1.7 / 0.7 1.7 / 0.6 16 mm 4 / 3.5 4 / 3 4 / 3 4 / 3.5 4 / 3 4 / 3 20 mm 5.5 / 4.5 5.5 / 3.5 5.5 / 2.5 5.5 / 4 5.5 / 3.5 5.5 / 3.5 5.5 / 3 5.5 / 3 25 mm 7 / 6.5 7 / 6 7 / 5.5 6.5 / 5 6.5 / 5 6.5 / 4.5 6.5 / 4.5 6.5 / 4 32 mm 13 / 12 13 / 11 13 / 10 11 / 9 11 / 9 11 / 8.5 11 / 8 11 / 7.5 40 mm 17 / 15 17 / 13 17 / 11 17 / 14 17 / 13 17 / 13 17 / 12 17 / 11 50 mm 22 / 20 22 / 18 22 / 16 23 / 20 23 / 19 23 / 18 23 / 17 23 / 16 2 Cylinders Compact Extruded
MAGNETIC PISTON OPTION Clippard pneumatic cylinders that are equipped with an internal auto switch (magnet) can be used with the Reed Switch and GMR Sensor. By accurately sensing the magnetic field of the piston when it passes beneath the sensor, the position of the rod piston is determined, and the feedback signal is created. Use of this option may add to the overall length of the cylinder. POSITION SENSOR SELECTION CHART Characteristics RPS-S GPS-N GPS-P RPS-N RPS-P Switching Logic SPST Normally-Open Solid-State Output, Normally-Open Solid-State Output, Normally-Open SPST Normally-Open SPST Normally-Open Sensor Type Reed Switch NPN Current Sinking PNP Current Sourcing Reed Switch NPN Reed Switch PNP Operating Voltage RPS-S3: 5 to 120 VAC RPS-S8Q: 5 to 60 VAC/DC Switching Current 100 ma max. 200 ma max. 200 ma max. 250 ma max. 250 ma max. Switching Rating 10 W max. 6 W max. 6 W max. 10 W max. 10 W max. Current Consumption - 7.5 ma max. @ 24 V (Switch Active) Voltage Drop 2.5 V max. @ 40 ma DC 0.5 V max. @ 200 ma (Resistive Load) 7.5 ma max. @ 24 V (Switch Active) 0.5 V max. @ 200 ma (Resistive Load) 10 ma max. @ 24 V (Switch Active) 0.5 V max. @ 550 ma (Resistive Load) 10 ma max. @ 24 V (Switch Active) 0.5 V max. @ 550 ma (Resistive Load) Leakage Current - 0.01 ma max. 0.01 ma max. - - Indicator Red LED Red LED Green LED Red LED Green LED Circuit Diagram Brown Blue Load ~ Power ~ Brown Black Load Power Blue Brown Black Power Blue Load MAIN CIRCUIT Brown Black Blue Load Power MAIN CIRCUIT Brown Black Blue Load Power Cable 2.8, 2C, Oil-Resistant PVC 2.8, 3C, Oil-Resistant PVC 2.8, 3C, Oil-Resistant PVC 2.8, 3C, Oil-Resistant PVC 2.8, 3C, Oil-Resistant PVC Sensitivity 60 G 40 ~ 750 G 40 ~ 750 G 60 G 60 G Max. Switching Freq. 200 Hz 5,000 Hz 5,000 Hz 1,000 Hz 1,000 Hz Temperature Range 14 to 158 F (-10 to 70 C) 14 to 158 F (-10 to 70 C) 14 to 158 F (-10 to 70 C) 14 to 158 F (-10 to 70 C) 14 to 158 F (-10 to 70 C) Shock 30 G 50 G 50 G 30 G 30 G Vibration 9 G 9 G 9 G 9 G 9 G Enclosure Classification IP 67 (NEMA 6) IP 67 (NEMA 6) IP 67 (NEMA 6) IP 67 (NEMA 6) IP 67 (NEMA 6) Protection Circuit - Power Source Reverse Polarity; Surge Suppression Power Source Reverse Polarity; Surge Suppression - - Quick Connector 2-Wire QD Wiring 3-Wire QD Wiring 4 (NC) (+) Brown 1 3 (-) Blue 4 (out) Black (+) Brown 1 3 (-) Blue ORDERING INFORMATION Reed Switch Part No. GMR Switch Part No. RPS-P3 Sourcing Switch with 3 m Wire Leads GPS-P3 Sourcing Switch with 3 m Wire Leads RPS-P8Q Sourcing Switch with 8 mm Male QC 6 Pigtail GPS-P8Q Sourcing Switch with 8 mm Male QC 6 Pigtail RPS-N3 Sinking Switch with 3 m Wire Leads GPS-N3 Sinking Switch with 3 m Wire Leads RPS-N8Q Sinking Switch with 8 mm Male QC 6 Pigtail GPS-N8Q Sinking Switch with 8 mm Male QC 6 Pigtail RPS-S3 Simple Switch (2-Wire) with 3 m Wire Leads CPS-C8Q5 Mating Cable Assembly, 8 mm Female QC with 5 m Leads RPS-S8Q Simple Switch (2-Wire) with 8 mm Male QC 6 Pigtail CPS-C8Q5 Mating Cable Assembly, 8 mm Female QC with 5 m Leads 3
SPECIFICATIONS, MOUNTING HARDWARE & ROD NUTS SPECIFICATIONS DOUBLE ACTING, ROTATING & DOUBLE ROD MODELS Bore Max. Stroke Thru Mtg. Hole Mounting Thread Rod End Thread Ports Rod Dia. 12 mm 30 3.5 mm thru M4x0.7-7mm deep / #8-32 UNC-2B M3x0.5-6mm deep / #6-32 M5x0.8 / #10-32 6 mm 16 mm 30 3.5 mm thru M4x0.7-7mm deep / #8-32 UNC-2B M4x0.7-8mm deep / #6-32 M5x0.8 / #10-32 8 mm 20 mm 50 5.5 mm thru M6x1.0-10mm deep / 1/4-20 UNC-2B M8x0.8-7mm deep / #10-32 M5x0.8 / #10-32 10 mm 25 mm 50 5.5 mm thru M6x1.0-10mm deep / 1/4-20 UNC-2B M6x1.0-12 mm deep / 1/4-28 M5x0.8 / #10-32 12 mm 32 mm 100 5.5 mm thru M6x1.0-10mm deep / 1/4-20 UNC-2B M8x1.25-13 mm deep / 5/16-14 G1/8 / 1/8 NPT 16 mm 40 mm 100 5.5 mm thru M6x1.0-10mm deep / 1/4-20 UNC-2B M8x1.25-13 mm deep / 3/8-24 G1/8 / 1/8 NPT 16 mm 50 mm 100 6.6 mm thru M8x1.25-14mm deep / 5/16-18 UNC-2B M10x1.5-15mm deep / 1/2-20 G1/4 / 1/4 NPT 20 mm SINGLE ACTING, SPRING RETURN & EXTENDED MODELS Bore Max. Stroke Thru Mtg. Hole Mounting Thread Rod End Thread Ports Rod Dia. 12 mm 20 3.5 mm thru M4x0.7-7mm deep / #8-32 UNC-2B M3x0.5-6mm deep / #6-32 M5x0.8 / #10-32 6 mm 16 mm 20 3.5 mm thru M4x0.7-7mm deep / #8-32 UNC-2B M4x0.7-8mm deep / #6-32 M5x0.8 / #10-32 8 mm 20 mm 30 5.5 mm thru M6x1.0-10mm deep / 1/4-20 UNC-2B M8x0.8-7mm deep / #10-32 M5x0.8 / #10-32 10 mm 25 mm 30 5.5 mm thru M6x1.0-10mm deep / 1/4-20 UNC-2B M6x1.0-12 mm deep / 1/4-28 M5x0.8 / #10-32 12 mm 32 mm 30 5.5 mm thru M6x1.0-10mm deep / 1/4-20 UNC-2B M8x1.25-13 mm deep / 5/16-14 G1/8 / 1/8 NPT 16 mm 40 mm 30 5.5 mm thru M6x1.0-10mm deep / 1/4-20 UNC-2B M8x1.25-13 mm deep / 3/8-24 G1/8 / 1/8 NPT 16 mm 50 mm 30 6.6 mm thru M8x1.25-14mm deep / 5/16-18 UNC-2B M10x1.5-15mm deep / 1/2-20 G1/4 / 1/4 NPT 20 mm MOUNTING HARDWARE ROD NUTS METRIC IMPERIAL Bore Part No. Thread Across Flats Thickness Part No. Thread Across Flats Thickness 12 mm NM5-080 M5x0.8 8 mm 4 mm NO2-32 #8-32 11/32 1/8 16 mm NM6-100 M6x1.0 10 mm 5 mm NO2-32 #8-32 11/32 1/8 20 mm NM8-125 M8x1.25 12 mm 4 mm NO3-32 #10-32 3/8 1/8 25 mm NM10-150 M10x1.25 17 mm 5 mm NO4-28A 1/4-28 7/16 5/32 32 mm NM14-150 M14x1.5 22 mm 7 mm NO5-24 5/16-24 1/2 3/16 40 mm NM14-150 M14x1.5 22 mm 7 mm NO6-24A 3/8-24 9/16 7/32 50 mm NM18-150 M18x1.5 27 mm 9 mm N08-20 1/2-20 3/4 5/16 4 Cylinders Compact Extruded
FOOT MOUNTING BRACKETS 12, 16, 20 & 25 mm Bore Sizes TS RH dia. thru 2 plcs HS1 H3 H Bore H H1 H3 HL HS1 L L2 RH TS 12 mm 44.0 5.0 22.0 2.0 34.0 29.5 17.0 4.5 8.0 16 mm 48.0 5.0 24.0 2.0 38.0 33.5 19.0 4.5 8.0 20 mm 62.0 7.0 31.0 3.2 48.0 42.0 24.0 6.5 9.2 25 mm 66.0 7.0 33.0 3.2 52.0 46.0 26.0 6.5 10.7 H1 HL L Order Part No. CQ2-(bore size)92 L2 Bore H H1 H3 HL HS1 L L2 RH TS 12 mm 1.732 0.197 0.866 0.078 1.339 1.161 0.669 0.177 0.315 16 mm 1.890 0.197 0.945 0.078 1.496 1.319 0.748 0.177 0.315 20 mm 2.441 0.276 1.220 0.125 1.890 1.654 0.945 0.256 0.362 25 mm 2.598 0.276 1.299 0.125 2.047 1.811 1.024 0.256 0.421 12, 16, 20 & 25 mm Bore Sizes with Auto Switch (Magnet) RH dia. thru 2 plcs HL TS HS1 H1 Order Part No. CQ2-(bore size)91 L2 L H3 H Bore H H1 H3 HL HS1 L L2 RH TS 12 mm 44.0 5.0 22.0 2.0 34.0 29.5 17.0 4.5 8.0 16 mm 48.0 5.0 24.0 2.0 38.0 33.5 19.0 4.5 8.0 20 mm 62.0 7.0 31.0 3.2 48.0 42.0 24.0 6.6 9.2 25 mm 66.0 7.0 33.0 3.2 52.0 46.0 26.0 6.6 10.7 Bore H H1 H3 HL HS1 L L2 RH TS 12 mm 1.732 0.197 0.866 0.078 1.339 1.161 0.669 0.177 0.315 16 mm 1.890 0.197 0.945 0.078 1.496 1.319 0.748 0.177 0.315 20 mm 2.441 0.276 1.220 0.125 1.890 1.654 0.945 0.260 0.362 25 mm 2.598 0.276 1.299 0.125 2.047 1.811 1.024 0.260 0.421 32, 40 & 50 mm Bore Sizes TS HL RH dia. thru 2 plcs HS1 H1 Order Part No. CQ2-(bore size)91 L2 H3 L H Bore H H1 H3 HL HS1 L L2 RH TS 32 mm 71.0 7.0 35.5 3.2 57.0 20.0 13.0 6.6 11.2 40 mm 78.0 7.0 39.0 3.2 64.0 20.0 13.0 6.6 11.2 50 mm 95.0 8.0 47.5 3.2 79.0 22.0 14.0 8.5 11.2 Bore H H1 H3 HL HS1 L L2 RH TS 32 mm 2.795 0.276 1.398 0.125 2.244 0.787 0.512 0.260 0.441 40 mm 3.071 0.276 1.535 0.125 2.520 0.787 0.512 0.260 0.441 50 mm 3.740 0.315 1.870 0.125 3.110 0.866 0.551 0.335 0.480 5
XDR SERIES / Double-Acting, Rotating Rod with Auto Switch (Magnet) DOUBLE-ACTING, ROTATING ROD WITH AUTO SWITCH (MAGNET) 12, 16, 20 & 25 mm Bore Sizes O (4 plcs) 8.0 U S (m op O (4 plcs) EA EB U S W1 V square nds s W L + stroke F s A: O1 2 plcs both ends B: N thru hole 2 plcs V square A: O1 2 plcs both ends B: N thru hole 2 plcs Bore Stroke L D EA EB F H K W M N 12 mm 5-30 28 6 - - 7 M3x0.5-6 deep 5 3.5 22 3.5 16 mm 30.5 8 13.2 6.6 5.5 M4x0.7-8 deep 6 3.5 28 3.5 20 mm 31.5 10 13.6 6.8 5.5 M5x0.8-7 deep 8 4.5 36 5.5 25 mm 32.5 12 13.6 6.8 5.5 M6x1-12 deep 10 5 40 5.5 Bore O P Q S U V W1 MM X O1 12 mm 6.5 x 3.5 deep M5x0.8 9 27 14 25 14 M5x0.8-9 long 10.5 M4x0.7x7 deep 16 mm 6.5 x 3.5 deep 9.5 29.5 15 29 15.5 M6x1-10 long 12 M4x0.7-7 deep 20 mm 9 x 7 deep 8 35.5 18 36 18.5 M8x1.25-12 long 14 M6x1-10 deep 25 mm 9 x 7 deep 9 40.5 21 40 22.5 M10x1.25-15 long 17.5 M6x1-10 deep Bore Stroke L D EA EB F H K W M N 12 mm 0.125-1.000 1.102 0.236 - - 0.276 #6-32-0.236 deep 0.197 0.138 0.866 0.138 16 mm 0.125-1.000 1.201 0.315 0.520 0.260 0.217 #6-32-0.315 deep 0.236 0.138 1.102 0.138 20 mm 0.125-2.000 1.240 0.394 0.535 0.268 0.217 #10-32-0.276 deep 0.315 0.177 1.417 0.217 25 mm 0.125-2.000 1.280 0.472 0.535 0.268 0.217 1/4-28-0.472 deep 0.394 0.197 1.575 0.217 Bore O P Q S U V W1 MM X O1 12 mm 0.256 x 0.138 deep #10-32 0.354 1.063 0.552 0.984 0.552 #8-32-0.356 long 0.413 #8-32 UNC-2B-0.276 deep 16 mm 0.256 x 0.138 deep 0.374 1.161 0.590 1.142 0.610 #8-32-0.394 long 0.472 #8-32 UNC-2B-0.276 deep 20 mm 0.354 x 0.276 deep 0.315 1.398 0.709 1.417 0.728 #10-32-0.472 long 0.551 1/4-20 UNC-2B-0.394 deep 25 mm 0.354 x 0.276 deep 0.354 1.594 0.826 1.575 0.886 1/4-28-0.591 long 0.689 1/4-20 UNC-2B-0.394 deep 6 Cylinders Compact Extruded
XDR SERIES / Double-Acting, Rotating Rod DOUBLE-ACTING, ROTATING ROD 12, 16, 20 & 25 mm Bore Sizes F dia. I A: O1 4 plcs both ends B: N thru hole 4 plcs M W W1 L + stroke O (8 plcs) Bore Stroke L D F H I W M N 12 mm 5-30 17 6 5 M3x0.5-6 deep 32 3.5 15.5 3.5 16 mm 18.5 8 5.5 M4x0.7-8 deep 38 3.5 20 3.5 20 mm 19.5 10 5.5 M5x0.8-7 deep 47 4.5 25.5 5.5 25 mm 22.5 12 5.5 M6x1-12 deep 52 5 28 5.5 Bore O P Q W1 MM X O1 12 mm 6.5 x 3.5 deep M5x0.8 7.5 14 M5x0.8-9 long 10.5 M4x0.7-7 deep 16 mm 6.5 x 3.5 deep 8 15. M6x1-10 long 12 M4x0.7-7 deep 20 mm 9 x 7 deep 8 18.5 M8x1.25-12 long 14 M6x1-10 deep 25 mm 9 x 7 deep 9 22.5 M10x1.25-15 long 17.5 M6x1-10 deep Bore Stroke L D F H I W M N 12 mm 0.125-1.000 0.669 0.236 0.197 #6-32-0.236 deep 1.260 0.138 0.610 0.138 16 mm 0.125-1.000 0.728 0.315 0.217 #6-32-0.315 deep 1.496 0.138 0.787 0.138 20 mm 0.125-2.000 0.768 0.394 0.217 #10-32-0.276 deep 1.850 0.177 1.004 0.217 25 mm 0.125-2.000 0.886 0.472 0.217 1/4-28-0.472 deep 2.047 0.197 1.102 0.217 Bore O P Q W1 MM X O1 2 mm 0.256 x 0.138 deep #10-32 0.295 0.552 #8-32-0.356 long 0.413 #8-32 UNC-2B-0.276 deep 16 mm 0.256 x 0.138 deep 0.315 0.610 #8-32-0.394 long 0.472 #8-32 UNC-2B-0.276 deep 20 mm 0.354 x 0.276 deep 0.315 0.728 #10-32-0.472 long 0.551 1/4-20 UNC-2B-0.394 deep 25 mm 0.354 x 0.276 deep 0.354 0.886 1/4-28-0.591 long 0.689 1/4-20 UNC-2B-0.394 deep 7
XDR SERIES / Double-Acting, Rotating Rod DOUBLE-ACTING, ROTATING ROD 32, 40 & 50 mm Bore Sizes F A: O1 4 plcs both ends B: N thru hole 4 plcs W O (8 plcs) W1 L + stroke J Without Switch With Switch Bore Stroke L F Q L F Q D H J K W 32 mm 5 23 6.5 7.5 33 6.5 7.5 16 M8x1.25-13 deep 4.5 14 7 10-50 23 7.5 10 33 7.5 10 50-100 33 7.5 10 33 7.5 10 40 mm 5 29.5 8 11 39.5 8 11 16 M8x1.25-13 deep 5 14 7 10-50 29.5 7.5 12.5 39.5 7.5 12.5 50-100 39.5 7.5 12.5 39.5 7.5 12.5 50 mm 5 30.5 9 9 40.5 9 9 20 M10x1.5-15 deep 7 17 8 10-50 30.5 10.5 10.5 40.5 10.5 10.5 50-100 40.5 10.5 10.5 40.5 10.5 10.5 Bore M N O P W1 MM X O1 32 mm 34 5.5 9 x 7 deep G1/8 28.5 M14x1.5-20.5 long 23.5 M6x1-10 deep 40 mm 40 5.5 9 x 7 deep G1/8 28.5 M14x1.5-20.5 long 23.5 M6x1-10 deep 50 mm 50 6.6 11 x 8 deep G1/4 33.5 M18x1.5-25.5 long 28.5 M8x1.25-14 deep Without Switch With Switch Bore Stroke L F Q L F Q D H J K W 32 mm 0.125 0.906 0.256 0.295 1.299 0.256 0.295 0.630 5/16-24-0.512 deep 0.177 0.551 0.275 0.250-2.000 0.906 0.295 0.394 1.299 0.295 0.394 2.125-4.000 1.299 0.295 0.394 1.299 0.295 0.394 40 mm 0.125 1.161 0.315 0.433 1.555 0.315 0.433 0.630 3/8-24-0.512 deep 0.197 0.551 0.275 0.250-2.000 1.161 0.295 0.492 1.555 0.295 0.492 2.125-4.000 1.555 0.295 0.492 1.555 0.295 0.492 50 mm 0.125 1.201 0.354 0.354 1.594 0.354 0.354 0.787 1/2-20-0.591 deep 0.275 0.669 0.315 0.250-2.000 1.201 0.413 0.413 1.594 0.413 0.413 2.125-4.000 1.594 0.413 0.413 1.594 0.413 0.413 Bore M N O P W1 MM X O1 32 mm 1.339 0.217 0.354 x 0.276 deep 1/8 NPT 1.123 5/16-24-0.807 long 0.925 1/4-20 UNC-2B-0.394 deep 40 mm 1.575 0.217 0.354 x 0.276 deep 1/8 NPT 1.123 3/8-24-0.807 long 0.925 1/4-20 UNC-2B-0.394 deep 50 mm 1.969 0.260 0.433 x 0.315 deep 1/4 NPT 1.319 1/2-20-1.004 long 1.122 5/16-18 UNC-2B- 0.551 deep 8 Cylinders Compact Extruded
XDD SERIES / Double-Acting, Double Rod with Auto Switch (Magnet) DOUBLE-ACTING, DOUBLE ROD WITH AUTO SWITCH (MAGNET) 12, 16, 20 & 25 mm Bore Sizes W O (4 plcs) 8.0 U S O (4 plcs) EA EB U S M (male - ns th ends 2 plcs W1 L + stroke W1 + stroke V square 12 mm A: O1 2 plcs both ends B: N thru hole 2 plcs V square 16-20-25 mm A: O1 2 plcs both ends B: N thru hole 2 plcs Bore Stroke L D EA EB H K W M N O 12 mm 5-30 32.4 6 - - M3x0.5-6 deep 5 3.5 22 3.5 6.5 x 3.5 deep 16 mm 36 8 13.2 6.6 M4x0.7-8 deep 6 3.5 28 3.5 6.5 x 3.5 deep 20 mm 38 10 13.6 6.8 M5x0.8-7 deep 8 4.5 36 5.5 9 x 7 deep 25 mm 39 12 13.6 6.8 M6x1-12 deep 10 5 40 5.5 9 x 7 deep Bore P Q S U V W1 MM X O1 12 mm M5x0.8 9 27 14 25 14 M5x0.8-9 long 10.5 M4x0.7-7 deep 16 mm 9.5 29.5 15 29 15.5 M6x1-10 long 12 M4x0.7-7 deep 20 mm 8 35.5 18 36 18.5 M8x1.25-12 long 14 M6x1-10 deep 25 mm 9 40.5 21 40 22.5 M10x1.25-17 long 17.5 M6x1-10 deep Bore Stroke L D EA EB H K W M N O 12 mm 0.125-1.000 1.276 0.236 - - #6-32-0.236 deep 0.197 0.138 0.866 0.138 0.256 x 0.138 deep 16 mm 0.125-1.000 1.417 0.315 0.520 0.260 #6-32-0.315 deep 0.236 0.138 1.102 0.138 0.256 x 0.138 deep 20 mm 0.125-2.000 1.496 0.394 0.535 0.268 #10-32-0.276 deep 0.315 0.177 1.417 0.217 0.354 x 0.276 deep 25 mm 0.125-2.000 1.535 0.472 0.535 0.268 1/4-28-0.472 deep 0.394 0.197 1.575 0.217 0.354 x 0.276 deep Bore P Q S U V W1 MM X O1 12 mm #10-32 0.354 1.063 0.551 0.984 0.551 #8-32-0.356 long 0.413 #8-32 UNC-2B-0.276 deep 16 mm 0.374 1.161 0.590 1.142 0.610 #8-32-0.394 long 0.472 #8-32 UNC-2B-0.276 deep 20 mm 0.315 1.398 0.709 1.417 0.728 #10-32-0.472 long 0.551 1/4-20 UNC-2B-0.394 deep 25 mm 0.354 1.594 0.826 1.575 0.886 1/4-28-0.591 long 0.689 1/4-20 UNC-2B-0.394 deep 9
XDD SERIES / Double-Acting, Double Rod DOUBLE-ACTING, DOUBLE ROD 12, 16, 20 & 25 mm Bore Sizes typ. I dia. A: O1 2 plcs both ends B: N thru hole 2 plcs W W + stroke W1 L + stroke W1 + stroke O (8 plcs) Bore Stroke L D H I K W M N O 12 mm 5-30 25.2 6 M3x0.5-6 deep 32 5 3.5 15.5 3.5 6.5 x 3.5 deep 16 mm 26 8 M4x0.7-8 deep 38 6 3.5 20 3.5 6.5 x 3.5 deep 20 mm 26 10 M5x0.8-7 deep 47 8 4.5 25.5 5.5 9 x 7 deep 25 mm 29 12 M6x1-12 deep 52 10 5 28 5.5 9 x 7 deep Bore P Q W1 MM X O1 12 mm M5x0.8 9 14 M5x0.8-9 long 10.5 M4x0.7-7 deep 16 mm 9.5 15.5 M6x1-10 long 12 M4x0.7-7 deep 20 mm 8 18.5 M8x1.25-12 long 14 M6x1-10 deep 25 mm 9 22.5 M10x1.25-15 long 17.5 M6x1-10 deep Bore Stroke L D H I K W M N O 12 mm 0.125-1.000 0.992 0.236 #6-32-0.236 deep 1.260 0.197 0.138 0.610 0.138 0.256 x 0.138 deep 16 mm 0.125-1.000 1.024 0.315 #6-32-0.315 deep 1.496 0.236 0.138 0.787 0.138 0.256 x 0.138 deep 20 mm 0.125-2.000 1.024 0.394 #10-32-0.276 deep 1.850 0.315 0.177 1.004 0.217 0.354 x 0.76 deep 25 mm 0.125-2.000 1.142 0.472 1/4-28-0.472 deep 2.047 0.394 0.197 1.102 0.217 0.354 x 0.276 deep Bore P Q W1 MM X O1 12 mm #10-32 0.354 0.551 #8-32-0.356 long 0.413 #8-32 UNC-2B-0.276 deep 16 mm 0.374 0.610 #8-32-0.394 long 0.472 #8-32 UNC-2B-0.276 deep 20 mm 0.315 0.728 #10-32-0.472 long 0.551 1/4-20 UNC-2B-0.394 deep 25 mm 0.354 0.886 1/4-28-0.591 long 0.689 1/4-20 UNC-2B-0.394 deep 10 Cylinders Compact Extruded
XDD SERIES / Double-Acting, Double Rod DOUBLE-ACTING, DOUBLE ROD 32, 40 & 50 mm Bore Sizes 2- P A: O1 4 plcs both ends B: N thru hole 4 plcs W1 W L + stroke W + stroke W1 + stroke O (8 plcs) J Without Switch With Switch Bore Stroke L L D H J K W M N 32 mm 5-50 30.5 40.5 16 M8x1.25-13 deep 4.5 14 7 34 5.5 50-100 40.5 40.5 40 mm 5-50 40 50 16 M8x1.25-13 deep 5 14 7 40 5.5 50-100 50 50 mm 5-50 40.5 50.5 20 M10x1.5-15 deep 7 17 8 50 6.6 50-100 50.5 50.5 Bore O P Q W1 MM X O1 32 mm 9 x 7 deep G1/8 10 28.5 M14x1.5-20.5 long 23.5 M6x1-10 deep 40 mm 9 x 7 deep G1/8 13 28.5 M14x1.5-20.5 long 23.5 M6x1-10 deep 50 mm 11 x 8 deep G1/4 13.5 33.5 M18x1.5-25.5 long 28.5 M8x1.25-14 deep Without Switch With Switch Bore Stroke L L D H J K W M N 32 mm 0.125-2.000 1.201 1.594 0.630 5/16-24-0.512 deep 0.177 0.551 0.275 1.339 0.217 2.125-4.000 1.594 40 mm 0.125-2.000 1.575 1.969 0.630 3/8-24-0.512 deep 0.197 0.551 0.275 1.575 0.217 2.125-4.000 1.969 50 mm 0.125-2.000 1.594 1.988 0.787 1/2-20-0.591 deep 0.275 0.669 0.315 1.969 0.260 2.125-4.000 1.988 Bore O P Q W1 MM X O1 32 mm 0.354 x 0.276 deep 1/8 NPT 0.394 1.123 5/16-24-0.807 long 0.925 1/4-20 UNC-2B-0.394 deep 40 mm 0.354 x 0.276 deep 1/8 NPT 0.512 1.123 3/8-24-0.807 long 0.925 1/4-20 UNC-2B-0.394 deep 50 mm 0.433 x 0.315 deep 1/4 NPT 0.531 1.319 1/2-20-1.004 long 1.122 5/16-18 UNC-2B -0.551 deep 11
XRR SERIES / Single-Acting, Spring Extended, Rotating Rod with Auto Switch (Magnet) SINGLE-ACTING, SPRING EXTENDED, ROTATING ROD WITH AUTO SWITCH (MAGNET) 12, 16, 20 & 25 mm Bore Sizes O (4 plcs) 8.0 U S O (4 plcs) EA EB U S W + stroke W1 + stroke L + stroke F V square A: O1 2 plcs both ends B: N thru hole 2 plcs V square A: O1 2 plcs both ends B: N thru hole 2 plcs 12 mm 16-20-25 mm Bore Stroke L D EA EB F H K W M N Q 12 mm 5-10 38 6 - - 7 M3x0.5-6 deep 5 3.5 22 3.5 9 15-20 48 16 mm 5-10 40.5 8 13.2 6.6 5.5 M4x0.7-8 deep 6 3.5 28 3.5 9.5 15-20 50.5 20 mm 5-10 41.5 10 13.6 6.8 5.5 M5x0.8-7 deep 8 4.5 36 5.5 8 15-30 51.5 25 mm 5-10 42.5 12 13.6 6.8 5.5 M6x1-12 deep 10 5 40 5.5 9 15-30 52.5 Bore O P S U V W1 MM X O1 12 mm 6.5 x 3.5 deep M5x0.8 27 14 25 14 M5x0.8-9 long 10.5 M4x0.7-7 deep 16 mm 6.5 x 3.5 deep 29.5 15 29 15.5 M6x1-10 long 12 M4x0.7-7 deep 20 mm 9 x 7 deep 35.5 18 36 18.5 M8x1.25-12 long 14 M6x1-10 deep 25 mm 9 x 7 deep 40.5 21 40 22.5 M10x1.25-17 long 17.5 M6x1-10 deep Bore Stroke L D EA EB F H K W M N Q 12 mm 0.125-0.375 1.496 0.236 - - 0.276 #6-32-0.236 deep 0.197 0.138 0.866 0.138 0.354 0.500-0.750 1.890 16 mm 0.125-0.375 1.594 0.315 0.520 0.260 0.217 #6-32-0.315 deep 0.236 0.138 1.102 0.138 0.374 0.500-0.750 1.988 20 mm 0.125-0.375 1.634 0.394 0.535 0.268 0.217 #10-32-0.276 deep 0.315 0.177 1.417 0.217 0.315 0.500-1.000 2.028 25 mm 0.125-1.000 1.674 0.472 0.535 0.268 0.217 1/4-28-0.472 deep 0.394 0.197 1.575 0.217 0.354 0.500-1.000 2.067 Bore O P S U V W1 MM X O1 12 mm 0.256 x 0.138 deep #10-32 1.063 0.551 0.984 0.551 #8-32-0.356 long 0.413 #8-32 UNC-2B-0.276 deep 16 mm 0.256 x 0.138 deep 1.161 0.590 1.142 0.610 #8-32-0.394 long 0.472 #8-32 UNC-2B-0.276 deep 20 mm 0.354 x 0.276 deep 1.398 0.709 1.417 0.728 #10-32-0.472 long 0.551 1/4-20 UNC-2B-0.394 deep 25 mm 0.354 x 0.276 deep 1.594 0.826 1.575 0.886 1/4-28-0.591 long 0.689 1/4-20 UNC-2B-0.394 deep 12 Cylinders Compact Extruded
XRR SERIES / Single-Acting, Spring Extended, Rotating Rod SINGLE-ACTING, SPRING EXTENDED, ROTATING ROD 12, 16, 20 & 25 mm Bore Sizes ends cs F I dia. A: O1 4 plcs both ends B: N thru hole 4 plcs (mal optio W + stroke W1 + stroke L + stroke O (8 plcs) Bore Stroke L D F H I K W M N 12 mm 5-10 27 6 5 M3x0.5-6 deep 32 5 3.5 15.5 3.5 15-20 37 5.5 M4x0.7-8 deep 6 3.5 28 3.5 16 mm 5-10 28.5 8 5.5 M4x0.7-8 deep 38 6 3.5 20 3.5 15-20 38.5 20 mm 5-10 29.5 10 5.5 M5x0.8-7 deep 47 8 4.5 25.5 5.5 15-30 39.5 25 mm 5-10 32.5 12 5.5 M6x1-12 deep 52 10 5 28 5.5 15-30 42.5 12 5.5 M6x1-12 deep 10 5 40 5.5 Bore O P Q W1 MM X O1 12 mm 6.5 x 3.5 deep M5x0.8 7.5 14 M5x0.8-9 long 10.5 M4x0.7-7 deep 16 mm 6.5 x 3.5 deep 8 15.5 M6x1-10 long 12 M4x0.7-7 deep 20 mm 9 x 7 deep 8 18.5 M8x1.25-12 long 14 M6x1-10 deep 25 mm 9 x 7 deep 9 22.5 M10x1.25-15 long 17.5 M6x1-10 deep Bore Stroke L D F H I K W M N 12 mm 0.125-0.375 1.063 0.236 0.197 #6-32-0.236 deep 1.260 0.197 0.138 0.610 0.138 0.500-0.750 1.457 16 mm 0.125-0.375 1.122 0.315 0.217 #6-32-0.315 deep 1.496 0.236 0.138 0.787 0.138 0.500-0.750 1.515 20 mm 0.125-0.375 1.161 0.394 0.217 #10-32-0.276 deep 1.850 0.315 0.177 1.004 0.217 0.500-1.000 1.555 25 mm 0.125-0.375 1.280 0.472 0.217 1/4-28-0.472 deep 2.047 0.394 0.197 1.102 0.217 0.500-1.000 1.673 Bore O P Q W1 MM X O1 12 mm 0.256 x 0.138 deep #10-32 0.295 0.551 #8-32-0.356 long 0.413 #8-32 UNC-2B-0.276 deep 16 mm 0.256 x 0.138 deep 0.315 0.610 #8-32-0.394 long 0.472 #8-32 UNC-2B-0.276 deep 20 mm 0.354 x 0.276 deep 0.315 0.728 #10-32-0.472 long 0.551 1/4-20 UNC-2B-0.394 deep 25 mm 0.354 x 0.276 deep 0.354 0.886 1/4-28-0.591 long 0.689 1/4-20 UNC-2B-0.394 deep 13
XRR SERIES / Single-Acting, Spring Extended, Rotating Rod SINGLE-ACTING, SPRING EXTENDED, ROTATING ROD 32, 40 & 50 mm Bore Sizes F A: O1 4 plcs both ends B: N thru hole 4 plcs 2- P (m op W + stroke O (8 plcs) W1 + stroke L + stroke J Without Switch With Switch Bore Stroke L F Q L F Q D H J K 32 mm 5 33 6.5 7.5 43 6.5 7.5 16 M8x1.25-13 deep 4.5 14 10 33 7.5 10 43 7.5 10 15-30 43 7.5 10 53 7.5 10 40 mm 5 39.5 8 11 49.5 8 11 16 M8x1.25-13 deep 5 14 10 39.5 7.5 12.5 49.5 7.5 12.5 15-30 49.5 7.5 12.5 59.5 7.5 12.5 50 mm 5 40.5 9 9 50.5 9 9 20 M10x1.5-15 deep 7 17 10 40.5 10.5 10.5 50.5 10.5 10.5 15-30 50.5 10.5 10.5 60.5 10.5 10.5 Bore W M N O P W1 MM X O1 32 mm 7 34 5.5 9 x 7 deep G1/8 28.5 M14x1.5-20.5 long 23.5 M6x1-10 deep 40 mm 7 40 5.5 9 x 7 deep G1/8 28.5 M14x1.5-20.5 long 23.5 M6x1-10 deep 50 mm 8 50 6.6 11 x 8 deep G1/4 33.5 M18x1.5-25.5 long 28.5 M8x1.25-14 deep Without Switch With Switch Bore Stroke L F Q L F Q D H J K 32 mm 0.125 1.299 0.256 0.295 1.299 0.256 0.295 0.630 5/16-24-0.512 deep 0.177 0.551 0.250-0.375 1.299 0.295 0.394 1.299 0.295 0.394 0.500-1.000 1.693 0.295 0.394 1.299 0.295 0.394 40 mm 0.125 1.555 0.315 0.433 1.555 0.315 0.433 0.630 3/8-24-0.512 deep 0.197 0.551 0.250-0.375 1.555 0.295 0.492 1.555 0.295 0.492 0.500-1.000 1.949 0.295 0.492 1.555 0.295 0.492 50 mm 0.125 1.594 0.354 0.354 1.594 0.354 0.354 0.787 1/2-20-0.591 deep 0.275 0.669 0.250-0.375 1.594 0.413 0.413 1.594 0.413 0.413 #10-32-0.276 deep 0.315 0.177 0.500-1.000 1.988 0.413 0.413 1.594 0.413 0.413 1/4-28-0.472 deep 0.394 0.197 Bore W M N O P W1 MM X O1 32 mm 0.275 1.339 0.217 0.354 x 0.276 deep 1/8 NPT 1.123 5/16-24-0.807 long 0.925 1/4-20 UNC-2B-0.394 deep 40 mm 0.275 1.575 0.217 0.354 x 0.276 deep 1/8 NPT 1.123 3/8-24-0.807 long 0.925 1/4-20 UNC-2B-0.394 deep 50 mm 0.315 1.969 0.260 0.433 x 0.315 deep 1/4 NPT 1.319 1/2-20-1.004 long 1.122 5/16-18 UNC-2B-0.551 deep 14 Cylinders Compact Extruded
XSR SERIES / Single-Acting, Spring Return, Rotating Rod with Auto Switch (Magnet) SINGLE-ACTING, SPRING RETURN, ROTATING ROD WITH AUTO SWITCH (MAGNET) 12, 16, 20 & 25 mm Bore Sizes O (4 plcs) 8.0 U S O (4 plcs) EA EB U S W W1 L + stroke F V square A: O1 2 plcs both ends B: N thru hole 2 plcs V square A: O1 2 plcs both ends B: N thru hole 2 plcs 12 mm 16-20-25 mm Bore Stroke L D EA EB F H K W M N O 12 mm 5-10 38 6 - - 7 M3x0.5-6 deep 5 3.5 22 3.5 6.5 x 3.5 deep 15-20 48 16 mm 5-10 40.5 8 13.2 6.6 5.5 M4x0.7-8 deep 6 3.5 28 3.5 6.5 x 3.5 deep 15-20 50.5 20 mm 5-10 41.5 10 13.6 6.8 5.5 M5x0.8-7 deep 8 4.5 36 5.5 9 x 7 deep 15-30 51.5 25 mm 5-10 42.5 12 13.6 6.8 5.5 M6x1-17 deep 10 5 40 5.5 9 x 7 deep 15-30 52.5 12 Bore P Q S U V W1 MM X O1 12 mm M5x0.8 9 27 14 25 14 M5x0.8-9 long 10.5 M4x0.7-7 deep 16 mm 9.5 29.5 15 29 15.5 M6x1-10 long 12 M4x0.7-7 deep 20 mm 8 35.5 18 36 18.5 M8x1.25-12 long 14 M6x1-10 deep 25 mm 9 40.5 21 40 22.5 M10x1.25-15 long 17.5 M6x1-10 deep Bore Stroke L D EA EB F H K W M N O 12 mm 0.125-0.375 1.496 0.236 - - 0.276 #6-32-0.236 deep 0.197 0.138 0.866 0.138 0.256 x 0.138 deep 0.500-1.000 1.890 0.315 16 mm 0.125-0.375 1.594 0.315 0.520 0.260 0.217 #6-32-0.315 deep 0.236 0.138 1.102 0.138 0.256 x 0.138 deep 0.500-1.000 1.988 20 mm 0.125-0.375 1.634 0.394 0.535 0.268 0.217 #10-32-0.276 deep 0.315 0.177 1.417 0.217 0.354 x 0.276 deep 0.500-1.000 2.028 25 mm 0.125-0.375 1.674 0.472 0.535 0.268 0.217 1/4-28-0.472 deep 0.394 0.197 1.575 0.217 0.354 x 0.276 deep 0.500-1.000 2.067 0.472 Bore P Q S U V W1 MM X O1 12 mm #10-32 0.354 1.063 0.551 0.984 0.551 #8-32-0.356 long 0.413 #8-32 UNC-2B-0.276 deep 16 mm 0.374 1.161 0.590 1.142 0.610 #8-32-0.394 long 0.472 #8-32 UNC-2B-0.276 deep 20 mm 0.315 1.398 0.709 1.417 0.728 #10-32-0.472 long 0.551 1/4-20 UNC-2B-0.394 deep 25 mm 0.354 1.594 0.826 1.575 0.886 1/4-28-0.591 long 0.689 1/4-20 UNC-2B-0.394 deep 15
XSR SERIES / Single-Acting, Spring Return, Rotating Rod SINGLE-ACTING, SPRING RETURN, ROTATING ROD 12, 16, 20 & 25 mm Bore Sizes J F I dia. A: O1 4 plcs both ends B: N thru hole 4 plcs W W1 L + stroke O (8 plcs) Bore Stroke L D F H I K W M N O 12 mm 5-10 27 6 5 M3x0.5-6 deep 32 5 3.5 15.5 3.5 6.5 x 3.5 deep 15-20 37 16 mm 5-10 28.5 8 5.5 M4x0.7-8 deep 38 6 3.5 20 3.5 6.5 x 3.5 deep 15-20 38.5 20 mm 5-10 29.5 10 5.5 M5x0.8-7 deep 47 8 4.5 25.5 5.5 9 x 7 deep 15-30 39.5 25 mm 5-10 32.5 12 5.5 M6x1-12 deep 52 10 5 28 5.5 9 x 7 deep 15-30 42.5 Bore P Q W1 MM X O1 12 mm M5x0.8 7.5 14 M5x0.8-9 long 10.5 M4x0.7-7 deep 16 mm 8 15.5 M6x1-10 long 12 M4x0.7-7 deep 20 mm 8 18.5 M8x1.25-12 long 14 M6x1-10 deep 25 mm 9 22.5 M10x1.25-15 long 17.5 M6x1-10 deep Bore Stroke L D F H I K W M N O 12 mm 0.125-0.375 1.063 0.236 0.197 #6-32-0.236 deep 1.260 0.197 0.138 0.610 0.138 0.256 x 0.138 deep 0.500-0.750 1.457 16 mm 0.125-0.375 1.122 0.315 0.217 #6-32-0.315 deep 1.496 0.236 0.138 0.787 0.138 0.256 x 0.138 deep 0.500-0.750 1.515 20 mm 0.125-0.375 1.161 0.394 0.217 #10-32-0.276 deep 1.850 0.315 0.177 1.004 0.217 0.354 x 0.276 deep 0.500-1.000 1.555 25 mm 0.125-0.375 1.280 0.472 0.217 1/4-28-0.472 deep 2.047 0.394 0.197 1.102 0.217 0.354 x 0.276 deep 0.500-1.000 1.673 Bore P Q W1 MM X O1 12 mm #10-32 0.295 0.551 #8-32-0.356 long 0.413 #8-32 UNC-2B-0.276 deep 16 mm 0.315 0.610 #8-32-0.394 long 0.472 #8-32 UNC-2B-0.276 deep 20 mm 0.315 0.728 #10-32-0.472 long 0.551 1/4-20 UNC-2B-0.394 deep 25 mm 0.354 0.886 1/4-28-0.591 long 0.689 1/4-20 UNC-2B-0.394 deep 16 Cylinders Compact Extruded
XSR SERIES / Single-Acting, Spring Return, Rotating Rod SINGLE-ACTING, SPRING RETURN, ROTATING ROD 32, 40 & 50 mm Bore Sizes F A: O1 4 plcs both ends B: N thru hole 4 plcs W W1 L + stroke J O (8 plcs) Without Switch With Switch Bore Stroke L F Q L F Q D H J K 32 mm 5 33 6.5 7.5 43 6.5 7.5 16 M8x1.25-13 deep 4.5 14 10 33 7.5 10 43 7.5 10 15-30 43 7.5 10 53 7.5 10 40 mm 5 39.5 8 11 49.5 8 11 16 M8x1.25-13 deep 5 14 10 39.5 7.5 12.5 49.5 7.5 12.5 15-30 49.5 7.5 12.5 59.5 7.5 12.5 50 mm 5 40.5 9 9 50.5 9 9 20 M10x1.5-15 deep 7 17 10 40.5 10.5 10.5 50.5 10.5 10.5 15-30 50.5 10.5 10.5 60.5 10.5 10.5 Bore W M N O P W1 MM X O1 32 mm 7 34 5.5 9 x 7 deep G1/8 28.5 M14x1.5-20.5 long 23.5 M6x1-10 deep 40 mm 7 40 5.5 9 x 7 deep G1/8 28.5 M14x1.5-20.5 long 23.5 M6x1-10 deep 50 mm 8 50 6.6 11 x 8 deep G1/4 33.5 M18x1.5-25.5 long 28.5 M8x1.25-14 deep Without Switch With Switch Bore Stroke L F Q L F Q D H J K 32 mm 0.125 1.299 0.256 0.295 1.693 0.256 0.295 0.630 5/16-24-0.512 deep 0.177 0.551 0.250-0.375 1.299 0.295 0.394 1.693 0.295 0.394 0.500-1.000 1.693 0.295 0.394 2.087 0.295 0.394 40 mm 0.125 1.555 0.315 0.433 1.949 0.315 0.433 0.630 3/8-24-0.512 deep 0.197 0.551 0.250-0.375 1.555 0.295 0.492 1.949 0.295 0.492 0.500-1.000 1.949 0.295 0.492 2.343 0.295 0.492 50 mm 0.125 1.594 0.354 0.354 1.988 0.354 0.354 0.787 1/2-20-0.591 deep 0.275 0.669 0.250-0.375 1.594 0.413 0.413 1.988 0.413 0.413 0.500-1.000 1.988 0.413 0.413 2.382 0.413 0.413 Bore W M N O P W1 MM X O1 32 mm 0.275 1.339 0.217 0.354 x 0.276 deep 1/8 NPT 1.123 5/16-24-0.807 long 0.925 1/4-20 UNC-2B-0.394 deep 40 mm 0.275 1.575 0.217 0.354 x 0.276 deep 1/8 NPT 1.123 3/8-24-0.807 long 0.925 1/4-20 UNC-2B-0.394 deep 50 mm 0.315 1.969 0.260 0.433 x 0.315 deep 1/4 NPT 1.319 1/2-20-1.004 long 1.122 5/16-18 UNC-2B-0.551 deep 17
ORDERING INFORMATION Part Number c CQ2 c c c - c - c - c Threads Metric M- Imperial Blank Mounting Type Threaded (Both ends) Thru Holes Cylinder Type Double Acting A B D Need to replace a cylinder from another manufacturer? Clippard s Online Interchange Guide makes it easy. Simply enter the other manufacturer s part number into any search box at Clippard.com and the Interchange will display the most similar Clippard versions, along with a full comparison of specifications. Single Acting, Spring Return S Reverse Acting, Spring Extend R Rod Type Rotating R Scan the code or visit clippard.com/link/interchange to learn more and try it out! Double (Double Acting only) D Bore Size (Port thread) 12 mm (M5 x 0.8 or #10-32) 12 16 mm (M5 x 0.8 or #10-32) 16 20 mm (M5 x 0.8 or #10-32) 20 2D DRAWINGS & 3D MODELS Available online at Clippard.com 25 mm (M5 x 0.8 or #10-32) 25 32 mm (G1/8 or 1/8 NPT) 32 40 mm (G1/8 or 1/8 NPT) 40 50 mm (G1/4 or 1/4 NPT) 50 Stroke (Enter exact stroke required) See Chart Options None Blank Auto Switch (Magnet) M MAXIMUM STANDARD STROKES Cylinder Bore Size Single /Reverse Acting Double Acting 12 mm, 16 mm 5 to 20 mm (1/8 to 3/4 ) 5 to 30 mm (1/8 to 1 ) 20 mm, 25 mm 5 to 30 mm (1/8 to 1 ) 5 to 50 mm (1/8 to 2 ) 32 mm, 40 mm, 50 mm 5 to 30 mm (1/8 to 1 ) 5 to 100 mm (1/8 to 4 ) Male Rod Thread No Thread PTFE Based Grease T N TG Standard strokes are available in 5 mm or 1/8 (0.125) increments. Example Part Numbers: 15 mm stroke M-CQ2-BDR-20-15 1-1/8 stroke CQ2-ADD-12-1.125 PROFESSIONALLY DISTRIBUTED BY: CLIPPARD INSTRUMENT LABORATORY, INC. 7390 Colerain Avenue, Cincinnati, Ohio 45239 513.521.4261 877.245.6247 ISO 9001:2015 clippard.com Technical Data Bulletin 10.16 For Warranty & Disclaimer Information, visit www.clippard.com/warranty