Published: Mar 30, 29 Drive Axle and Differential Principle of Operation For additional, refer to section 205-02 - Drive Axle/Differential of the workshop manual. Inspection and Verification 1. Verify the customer concern. 2. Confirm which, if any, warning lights and/or messages were displayed on the instrument cluster. For a list of messages, refer to the relevant section of the workshop manual. 3. Visually inspect for obvious mechanical or electrical faults. Mechanical Differential oil leakage Sensor installation Electrical Fuse(s) Wiring harness physical damage or water ingress Loose or corroded electrical connectors Controller area network (CAN) circuits Sensors 4. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step. 5. Use the approved diagnostic system or a scan tool to retrieve any diagnostic trouble codes (DTCs) before moving onto the symptom chart or DTC index. Make sure that all DTCs are cleared following rectification. Symptom Chart Symptom Running at reduced capability with fault present Possible message fault Possible other warnings Possible causes Action Driveline overheat warning lamp /driveline fault warning lamp Water ingress to wiring harness or connectors Reduced capability Differential increased tolerances Internal fault control module fault ( Visually inspect the wiring harness and connectors for water ingress. Refer to the warranty policy and procedures manual if a module is suspect. landrovertechinfo.com/ /frmviewit.js 1/5
control module) overheat Overheat Slow Down Driveline overheat warning lamp Oil level incorrect Oil level incorrect specification Sensor fault Internal fault Check for correct oil quantity and specifications. Refer to the relevant section of the workshop manual. DTC index NOTE: NOTE: Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra read by the manufacturer-approved diagnostic system). Intermittent faults may cause DTCs to be logged, however some DTCs may be cleared during an ignition off, ignition on cycle. Carry out a road test (if safe to do so), check the functionality of the system and retrieve any DTCs before turning the ignition off. DTC Description Possible causes Action P0562- System Voltage Low voltage supply below 9V Check the charge condition, refer to the electrical guides and check the actuator sensor circuit, repair as necessary P0563- System Voltage High voltage supply below 16V Check the charging circuit and condition P0604- Module Random Access Memory (RAM) Error - no sub type renew the. Refer to the warranty policy P0605- Module Read Only Memory (ROM) Error renew the. Refer to the warranty policy P0606- Control Module Processor - no sub type Watchdog reset This is a check DTC and is not necessarily a fault. If no other DTCs are logged and no customer complaint exists, clear/ignore this DTC P0607- Control Module Performance - no sub type renew the. Refer to the warranty policy P0652- Sensor Reference Voltage 'B' Circuit Low Actuator position sensor below 57V actuator sensor position circuit, repair as actuator P0653- Sensor Reference Voltage 'B' Circuit Actuator position sensor actuator sensor position circuit, repair as landrovertechinfo.com/ /frmviewit.js 2/5
High below 83V actuator P0666- P0712- P0713- P0806- PCM/ECM/TCM Internal Sensor 'A' Circuit - Sensor 'A' Circuit Low Sensor 'A' Circuit High Sensor Circuit Range/Performance 105 C ground Mismatch of actual and expected/calculated actuator position Internal actuator error This is a check DTC and is not necessarily a fault. If no other DTCs are logged and no customer complaint exists, clear this DTC and retest. If the problem persists, renew the control module. Refer to the warranty policy and procedures manual if a module is suspect actuator sensor circuit, repair as actuator actuator sensor circuit, repair as actuator Calibrate the clutch and range change mechanism using the approved diagnostic system or by the procedure listed in the description and operation. Refer to the relevant section of the workshop manual. renew the actuator P0807- Sensor Circuit Low - position sensor supply, ground, signal 1 or 2 open circuit or sensor supply, signal 1 or 2 short circuit to ground actuator circuit, repair as necessary. If no circuit problems exist, renew the actuator P0808- Sensor Circuit High position sensor signal 1 or 2 short circuit to actuator circuit, repair as necessary. If no circuit problems exist, renew the actuator P080A- Not Learned - no sub type (RDCM) not calibrated Differential clutch stuck or out of tolerance Using the approved diagnostic equipment, calibrate the rear. Clear the DTC and retest. If the problem persists, renew the rear procedures manual if a is suspect P0810-92 P0894- P09- Control Error - performance or incorrect operation Transmission Component Slipping - no sub type This DTC is for only magnetic brake is slipping If DTC P186D- is also logged in the rear, refer to repair actions as necessary. If DTC P186D- is not logged no repair action is necessary. Renew the actuator landrovertechinfo.com/ /frmviewit.js 3/5
P09- supply open circuit Circuit/Open - no sub type actuator circuit, repair as necessary P0901- Circuit Range/Performance supply short circuit actuator circuit, repair as necessary P0902- Circuit Low - no sub type supply circuit short to ground. actuator circuit, repair as necessary P0903- Circuit High - no sub type supply circuit short to actuator circuit, repair as necessary P1603- EEPROM Malfunction - no sub type renew the. Refer to the warranty policy P1783- Transmission Over- Condition - no sub type Differential oil sump 150 C. Check the rear oil quantity and problem persists, renew the rear procedures manual if a is suspect P186A- Control Circuit/Open Open circuit of actuator magnetic brake supply leads actuator circuit, repair as necessary. If no circuit problems exist, renew the actuator P186B- P186C- Control Circuit Low - Control Circuit High Short circuit to ground of both actuator magnetic brake pins Short circuit to of both actuator magnetic brake pins actuator circuit, repair as necessary. If no circuit problems exist, renew the actuator actuator circuit, repair as necessary. If no circuit problems exist, renew the actuator P186D- Stuck Actuator fault Using the approved diagnostic equipment, calibrate the rear /clutch actuator. renew the actuator P2742- P2743- Sensor 'B' Circuit Low Sensor 'B' Circuit High oil sump sensor short circuit to ground oil sump oil sensor circuit, repair as necessary oil sensor circuit, repair as necessary Actuator landrovertechinfo.com/ /frmviewit.js 4/5
150 C Extensive. Check the rear oil quantity and prolonged off-road P2785- Too use Insufficient oil High quantity Incorrect oil problem persists, renew the rear specification Internal procedures manual if a is suspect problem P2787- U01-88 U0102-87 U0122-87 U03-55 U1A14-49 Clutch Too High - no sub type High Speed CAN Bus - bus off With Transfer Case Control Module - missing message With Vehicle Dynamics Control Module - missing message Module Software Incompatibility - not configured CAN Initialization Failure - electronic failure clutch pack (calculated) above 2 C High speed CAN Bus (CAN Bus Off) with TCCM with VDM not configured supervision software failure Internal control module failure. Check the rear oil quantity and problem persists, renew the rear procedures manual if a is suspect Refer to the Network s section of the workshop manual Refer to the bus off statement within workshop manual section 418-. Refer to the Network s section of the workshop manual Refer to the bus off statement within workshop manual section 418-. Refer to the Network s section of the workshop manual Configure the module using the approved diagnostic system Configure the module using the approved diagnostic system. Clear the DTC and retest. If the problem persists, renew the. Refer to the warranty policy and procedures manual if a module is suspect landrovertechinfo.com/ /frmviewit.js 5/5