DRAFTS IN WIDE CIRCULATION Document Despatch Advice REFERENCE Date ETD 06/ T-90 04-01-2017 TECHNICAL COMMITTEE ETD 06 ---------------------------------------------------------------- ------- -------------------------------------------- ADDRESSED TO: 1. All Members of Electrical Insulators and Accessories Sectional Committee, ETD 06 ; 2. All Members of Electrotechnical Division Council; and 3. All other Interested. Dear Sir(s), Please find enclosed a copy each of the following draft Indian Standards: DOC NO. TITLE ETD 06 (11166) Insulators for overhead lines with a nominal voltage above 1 000 V Part 1: Ceramic or glass insulator units for a.c. systems Definitions, test methods and acceptance criteria Kindly examine the draft standards and forward your views stating any diffic ulties which you are likely to experience in your business or profession, if these are finally adopted as Indian Standards. Comments, if any, may please be made in the format given overleaf and mailed to the undersigned. Last date for comments: 03-05-2017. In case no comments are received or comments received are of editorial nature, you will kindly permit us to presume your approval for the above document as finalized. However, in case of comments of technical in nature are received then it may be finalized either in consultation with the Chairman, Sectional Committee or referred to the Sectional Committee for further necessary action, if so desired by the Chairman, Sectional Committee. It may kindly be noted that the technical contents of the documents has not been enclosed as these are identical with the corresponding IEC standards. For details, please refer to the corresponding IEC publication as mentioned in the respective National Forewords or kindly contact the undersigned. Thanking you, Yours faithfully (Rajeev Sharma) Sc E & Head (Electrotechnical) Email: eetd@bis.org.in Encl: As above
E व य पक प पक च ल म म द तपम प दम तत : ईट ड 06 प र षत : 1. ईट ड 06 क सभ सदस य 2. व द य त तकन क व भ ग पर षद क सभ सदस य त 3. र च खन ल अन य सभ नक य मह दय, क प य न नललखखत मस द क एक प र त स लग न ह : प र ख श षषप प र ख प र षण द ज ञ पकम द भष ईट ड द म प ईट ड 06/ ट -90 04-01-2017 श षषक श षषक ईट ड 06 (11166) 1000 व ल ट द अध प मश पक इन द ह त वव त प भ ग 1 ए द मदस ट ह त ल म म ट ट एव प ल प वव त प इप इयआ - पकच भ ष य, पक क षण पकद ततय एव स व प तत म ड क प य न मस दक क अ ल कन क औ अपन स म तय यह तत त ह ए भ औ क अ तत: य द यह म नक क र प म प रक लशत ह ए त स प अमल क न मऔ आपक व य स य अ क त मऔ य क न य आ सकत ह स म तय भ न क अ तम त ख 05-03-2017. स म तय य द क ई ह त क प य अगल प प दए प र मऔ अ हस त क षर क रपर ललखखत पत प भ दऔ य द क ई स म त प र प त नह ह त अ स म त मऔ क ल भ ष स त र ट ह ई त रप त प रल ख क य त अ त म र प दय एग य द क ई स म त तकन क प रक त क ह ई त व षय सलम त क अध यक षर क प मशष स अ रनक च छ प आग क क यष ह क ललए व षय सलम त क भ न क त द प रल ख क अ त म र प द दय एग क पय न ट क औ क मस दक क तकन क व षय स त स लल ग नत नह कय गय ह यक क य मस द आई. ई. स. म नकक क समर प ह व स त त य क ललए क पय स त च त र य प र क न मऔ र ल लखखत आई. ई. स. प रक शन पढऔ अ अ हस त क षर र त क स पकष क औ न य द, भ द य, ( शम ष) ज ञ नक ई ए प रम ख (व द य त तकन क )
Date Document No. 04-01-2017 ETD 06 (11166) Sl. No. Name of the Organization Clause/ Subclause Paragraph/Figure/ Table Type of Comment (General/Technical/ Editorial) Comments Proposed changes
Electrical Insulators and Accessories Sectional Committee, ETD 06 NATIONAL FOREWORD This Indian Standard (Part 1) which is identical with IEC 60383-1 Insulators for overhead lines with a nominal voltage above 1 000 V Part 1: Ceramic or glass insulator units for a.c. systems Definitions, test methods and acceptance criteria issued by the International Electrotechnical Commission (IEC) would be adopted by the Bureau of Indian Standards on the recommendations of the Electrical Insulators and Accessories Sectional Committee, ETD 06 and approval of the Electrotechnical Division Council. With the publication of this standard, IS 3188 : 1980 Characteristics of String Insulator Units shall be withdrawn. The text of IEC Standard has been approved as suitable for publication as an Indian Standard without deviations. Certain terminology and conventions are however not identical to those used in Indian Standards. Attention is particularly drawn to the following: a) Wherever the words International Standard appear referring to this standard, they should be read as Indian Standard. b) Comma (,) has been used as a decimal marker while in Indian Standards, the current practice is to use a point (.) as the decimal marker. In this adopted standard, reference appears to the following International Standards for which Indian Standards also exist. The corresponding Indian Standards, and documents under print which are to be substituted in their places, are listed below along with their degree of equivalence for the editions indicated: International Standard Corresponding Indian Standard Degree of Equivalence IEC 60050 (471) International Electrotechnical Vocabulary (IEV) Chapter 471: Insulators IEC 60060-1, High-voltage test techniques Part 1: General definitions and test requirements IEC 60273 : 1990, Characteristics of indoor and outdoor post insulators for systems with IEC 60305 : 1978, Characteristics of string insulator units of the cap and pin type IEC 60372 : 1984, Locking devices for ball and socket couplings of IS 1885 (Part 54) : 1993 Electrotechnical Vocabulary: Part 54 Insulators IS 2071 (Part 1) : 2016 Highvoltage Test Techniques: Part 1 General Definitions and Test Requirements ( Third Revision IS 5350 (Part 1 to Part 3) Dimensions of Indoor and Outdoor Porcelain Post Insulators and Post Insulator Units for Systems with Nominal Voltages Greater than 1000 V IS 3188 : 1980 Characteristics Of String Insulator Units IS/IEC 60372 : 1984 Locking Devices for Ball and Socket Identical with IEC 60050 (471) : 1984 Identical with IEC 60060-1 : 1989 Identical
string insulation units: Dimensions and tests IEC 60471: 1977, Dimensions of clevis and tongue couplings of string insulator units Couplings of String Insulators Units - Dimensions and Tests IS 3188 : 1980 Characteristics Of String Insulator Units The technical committee has reviewed the provisions of the following International Standards referred in this adopted standard and has decided that they are acceptable for use in conjunction with this standard. International Standard IEC 60120 : 1984 IEC 60433 : 1980 IEC 60720 : 1981 IEC XXX : 19XX ISO 1459 : 1971 Title Dimensions of ball and socket couplings of string insulator units Characteristics of string insulator units of the long rod type Characteristics of line post insulators Puncture testing of insulators of glass or ceramic material for overhead Metallic coatings Protection against corrosion by hot dip galvanizing Guiding principles ISO 1460 : 1971 ISO 1461 : 1971 ISO 1463 : 1982 ISO 2064 : 1980 Metallic coatings Hot dip galvanized coatings on ferrous metals Gravimetric determination of the mass per unit area Metallic coatings Hot dip galvanized coatings on fabricated ferrous products Requirements Metal and oxide coatings Measurement of coating thickness Microscopical method Metallic and other non-organic coatings Definitions and conventions concerning the measurement of thickness ISO 2178 : 1982 Non-magnetic coatings on magnetic substrates Measurement of coating thickness Magnetic method Only English language text has been retained while adopting it in this Indian Standard, and as such the page numbers given here are not the same as in the International Standard For the purpose of deciding whether a particular requirement of this standard is complied with, the final value, observed or calculated expressing the result of a test, shall be rounded off in accordance with IS 2 : 1960 Rules for rounding off numerical values (revised). The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard.