Toggle (Side-Step) Dual-Channel LED Driver ZLED7002 Datasheet Brief Description The ZLED7002 toggle (side-step) dual-channel LED driver is one of our ZLED family of LED control ICs. It operates in the lower DC voltage supply range of 2.7V to 5.5V. This unique LED driver is capable of controlling a MAIN channel and a SUB channel. Typically, only one of the two channels is active and the ZLED7002 toggles between the channels automatically in response to the voltage supply level and the related voltage at the UV (under-voltage protection) pin. A high-to-low transition of the power supply causes the output current to switch from the MAIN channel to the SUB channel if the UV pin voltage (V UV-PIN) is below the ZLED7002 s under-voltage threshold (V UVTHRSH=1.17V, typical). A low-to-high transition switches the output current from the SUB channel to the MAIN channel if the UV pin voltage is 80mV (typical) above the under-voltage threshold. The MAIN channel is a configurable constant current source driving the MAIN LED string with a maximum current draw of 250mA. The MAIN LED channel current is set by an external resistor (R3) connected to the Iset pin. Alternately, the SUB channel is activated when the ZLED7002 s SUB pin is pulled to ground. Its current is determined by the forward voltage of the SUB LED and external components. The SUB channel can drive up to 100mA current through the LED channel when active. The ZLED7002 enables voltage-level indicator applications and low-power battery-driven lighting applications that require switching to a lower-current LED channel when the supply is low, which extends the lighting lifetime. Because the dropout voltage (V DP) is minimal (as low as 0.1V when the MAIN channel output current is ~200mA), the ZLED7002 is optimal for battery-powered applications. Capable of operating efficiently with DC voltage supplies ranging from 2.7V to 5.5V, it is ideal for small portable lighting applications. The ZLED7002 can also reduce bill-of-material costs because very few external components are required for most applications, making it an optimal fit for small devices for which lighting lifetime is critical. Only four resistors, a diode, and a capacitor are needed for a typical basic application. Features + DC - Automatic MAIN channel short-circuit protection switches the output current to the SUB channel if the MAIN LED is shorted Under-voltage power supply detection Over-temperature protection Benefits Extends lighting life-time by switching to a lowercurrent LED channel when the supply is low 80mV (typical) hysteresis prevents unintended switching activation due to power supply ripple Ultra low quiescent current: 250μA typical Very few external components needed for operation Available Support Evaluation Kit Physical Characteristics Voltage supply: 2.7V to 5.5V DC Operating temperature: -25 C to 85 C Small SOP8 package ZLED7002 Typical Application Circuit 2.7 to 5.5 V R1 ZLED7002 VCC SUB UV MAIN D1 R4 SUB LED MAIN LED Iset GND C1 R2 R3 NC NC SW1 2016 Integrated Device Technology, Inc. 1 April 20, 2016
Toggle (Side-Step) Dual-Channel LED Driver ZLED7002 Datasheet SOP8 Package Dimensions and Pin Assignments Symbol Dimension (mm, except θ) Min Max A 1.350 1.750 A1 0.100 0.250 A2 1.450 Typical b 0.350 0.490 c 0.178 0.250 D 4.800 5.000 E 3.800 4.000 E1 5.800 6.240 Typical Applications Battery-driven LED lighting including Helmet lighting Bicycle lighting Miner lamps Pocket lights Voltage-level indicators General purpose low-voltage industrial and consumer LED applications e 1.270 Typical L 0.400 1.270 θ 0 8 Ordering Information Product Sales Code Description Package ZLED7002ZI1R ZLED7002 Toggle (Side-Step) Dual-Channel LED Driver SOP8 (Tape & Reel) ZLED7002KIT-E1 ZLED7002 Evaluation Kit Kit Corporate Headquarters 6024 Silver Creek Valley Road San Jose, CA 95138 www.idt.com Sales 1-800-345-7015 or 408-284-8200 Fax: 408-284-2775 www.idt.com/go/sales Tech Support www.idt.com/go/support DISCLAIMER Integrated Device Technology, Inc. (IDT) reserves the right to modify the products and/or specifications described herein at any time, without notice, at IDT's sole discretion. Performance specifications and operating parameters of the described products are determined in an independent state and are not guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the suitability of IDT's products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property rights of IDT or any third parties. IDT's products are not intended for use in applications involving extreme environmental conditions or in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT. Integrated Device Technology, IDT and the IDT logo are trademarks or registered trademarks of IDT and its subsidiaries in the United States and other countries. Other trademarks used herein are the property of IDT or their respective third party owners. For datasheet type definitions and a glossary of common terms, visit www.idt.com/go/glossary. All contents of this document are copyright of Integrated Device Technology, Inc. All rights reserved. 2016 Integrated Device Technology, Inc. 2 April 20, 2016
Contents 1 IC Characteristics... 4 1.1. Absolute Maximum Ratings... 4 1.2. Operating Conditions... 4 1.3. Electrical Parameters... 4 1.4. Typical Performance Graphs... 5 2 Circuit Description... 6 2.1. ZLED7002 Overview... 6 2.2. Under-Voltage Threshold... 7 2.3. Main LED Current... 7 2.4. Sub LED Current... 7 2.5. ZLED7002 Protection Features... 8 2.5.1. Over-Temperature Protection... 8 2.5.2. Main LED Short-Circuit Protection... 8 3 Application Circuit Design... 9 3.1. Applications... 9 3.2. Application Circuit Layout Requirements... 9 4 ESD Protection... 10 5 Pin Configuration and Package... 10 6 Ordering Information... 12 7 Document Revision History... 12 List of Figures Figure 1.1 Iset Pin Voltage versus Temperature (+10 C to 100 C)... 5 Figure 1.2 Main LED Current versus Power Supply (4V to 5.4V DC)... 6 Figure 3.1 Basic ZLED7002 Application Circuit... 9 Figure 5.1 ZLED7002 Pin Configuration... 10 Figure 5.2 SOP8 Package Drawing... 11 List of Tables Table 5.1 ZLED7002 Pin Descriptions and Connection Requirements SOP8 Package... 10 Table 5.2 SOP8 Package Dimensions... 11 2016 Integrated Device Technology, Inc. 3 April 20, 2016
1 IC Characteristics 1.1. Absolute Maximum Ratings No. PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNIT 1.1.1 Input voltage V CC -0.3 6.5 V 1.1.2 Iset pin voltage V ISET -0.3 6.5 V 1.1.3 UV pin voltage V UV-PIN -0.3 6.5 V 1.1.4 MAIN pin voltage V MAIN -0.3 6.5 V 1.1.5 SUB pin voltage V SUB -0.3 6.5 V 1.1.6 MAIN pin current I MAIN_ABS 500 ma 1.1.7 SUB pin current I SUB_ABS 300 ma 1.1.8 ESD performance P tot Human Body Model ±4 kv 1.1.9 Junction temperature T J 150 C 1.1.10 Storage temperature T S -60 150 C 1.2. Operating Conditions No. PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNIT 1.2.1 Operating temperature T amb -25 +85 C 1.2.2 Input voltage V CC 2.7 5.5 V 1.3. Electrical Parameters Except as noted, conditions for the following specifications are T amb = -25 C to +85 C (25 C typical); V CC = 2.7V to 5.5V. Production testing of the chip is performed at 25 C; V CC=3.6V, unless otherwise stated. Functional operation of the chip and specified parameters at other temperatures are guaranteed by design, characterization, and process control. No. PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNIT 1.3.1 Quiescent current I CC 2.7 V CC 5.5; 1.4 < V UV-PIN < 5.5; no load 250 320 ua 1.3.2 I MAIN to I ISET ratio -- V CC = 4.2V, R3 = 30KΩ 8000 1.3.3 Iset pin voltage V ISET 1.2 V 1.3.4 Main LED current accuracy -- V CC = 2.7V; V MAIN =0.5V ±5 % 1.3.5 Dropout voltage MAIN channel current source 1.3.6 ON resistance SUB channel V DP Iout=204mA, Rset=47K 0.2 V R SUB 2.7V Vcc 5.5V 2.0 Ω 1.3.7 UV pin under-voltage threshold V UVTHRSH Switches from MAIN LED to SUB LED if V UV-PIN transitions from high to low voltage and V UV-PIN is lower than V UVTHRSH. 1.13 1.17 1.21 V 2016 Integrated Device Technology, Inc. 4 April 20, 2016
No. PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNIT 1.3.8 UV pin comparator hysteresis (upper threshold undervoltage threshold) 1.3.9 Thermal protection threshold 1.3.10 Junction-to-ambient temperature V UVHYS Switches from SUB LED to MAIN LED if V UV-PIN transitions from low voltage to high voltage and V UV-PIN is higher than V UVTHRSH + V UVHYS (the upper threshold). 80 mv T SD 160 C RθJA 128 C/W 1.3.11 MAIN pin current I MAIN 250mA ma 1.3.12 SUB pin current I SUB 100mA ma 1.4. Typical Performance Graphs Figure 1.1 Iset Pin Voltage versus Temperature (+10 C to 100 C) VISET Temperature 2016 Integrated Device Technology, Inc. 5 April 20, 2016
Figure 1.2 Main LED Current versus Power Supply (4V to 5.4V DC) IMAIN (ma) V DC (Volts) 2 Circuit Description 2.1. ZLED7002 Overview The ZLED7002 is an LED driver for two channels designated as the MAIN channel and the SUB channel. Typically, only one of the channels is on and the other is off. External resistors R1 and R2 connected to UV pin form a voltage divider across the power supply. When the power supply voltage has risen high enough to create a voltage at the UV pin that is above a set threshold, the MAIN LED channel is activated and the SUB channel is off. If the supply falls and the resulting voltage at the UV pin is below the threshold, the SUB channel becomes active and the MAIN channel is turned off. When the MAIN channel is active, the ZLED7002 provides a constant current source for driving the MAIN LED channel. Its current level is set by an external resistor (R3) between the Iset and GND pins (see section 2.3). When the SUB LED channel is active, its current is determined by external components (see section 2.4) and the ZLED7002 pulls the SUB pin to ground. Refer to the application circuit in Figure 3.1 for the location of the components referred to in the following sections. 2016 Integrated Device Technology, Inc. 6 April 20, 2016
2.2. Under-Voltage Threshold The ZLED7002 s UV pin enables under-voltage detection. When a high-to-low transition occurs on the power supply voltage and the voltage at the UV pin falls below the under-voltage threshold (typically 1.17V), the ZLED7002 automatically turns off the MAIN LED channel and actives the SUB channel. There is an 80mV hysteresis for the under-voltage threshold to prevent unintended activation due to power supply ripple. When a low-to-high transition occurs on the power supply voltage, the SUB channel is turned off and the MAIN channel is activated if the UV pin voltage is 80mV (typical) above the under-voltage threshold. The voltage at the UV pin (V UV-PIN) is determined by the ratio of the external resistors R1 and R2 (see Figure 3.1), which connect to the UV pin to form a voltage divider across the power supply. V UV-PIN can be calculated with equation (1): V UV PIN = V CC R2 R1 + R2 (1) If the values for R1 and R2 are low, high current will flow through them resulting in lower system efficiency. Typical values for R1 and R2 are in the magnitude of 10 5 ; e.g., 51kΩ. For design purposes, it is helpful to select the value for R2 first and then compute R1 as needed to achieve the target ratio. For applications using a lithium battery, which typically maintains ~3.7V during its discharge stage, setting V UV-PIN to 3.4V is recommended. 2.3. Main LED Current The R3 resistor connected between the Iset and GND pins determines the level of the constant current through the MAIN LED channel, which is typically 8000 times the current of the Iset pin. The voltage at the Iset pin is a constant 1.2V, which is unaffected by environmental temperature and any power supply voltage changes as shown in Figure 1.1 and Figure 1.2. The MAIN LED current flows through the MAIN pin to ground, so voltage dropout is minimal (as low as 0.1V when the MAIN channel current is 200mA). Note: System efficiency is reduced if the power supply voltage is larger than the MAIN LED s voltage. In this case, the additional voltage is added to the MAIN pin voltage. The MAIN LED channel current (I MAIN) is calculated via equation (2): I MAIN V = 8000 R3 ISET (2) 2.4. Sub LED Current The SUB LED channel current is determined by the external R4 resistor in series with the connected SUB LED string, the SUB LED forward voltage, and the voltage drop across the D1 Zener diode connected from the cathode of the SUB LED to the SUB pin. When the SUB channel is active, its current flows through the SUB pin to ground. 2016 Integrated Device Technology, Inc. 7 April 20, 2016
The SUB LED channel current (I SUB) is calculated via equation (3): I SUB V = CC V FSUB LED R4 V FD1 (3) Where V FSUB-LED = The forward voltage of the SUB LED V FD1 = The forward voltage of Zener diode D1, which should be as small as possible 2.5. ZLED7002 Protection Features 2.5.1. Over-Temperature Protection The ZLED7002 includes protection from damage due to over-temperature conditions. The ZLED7002 automatically turns off if its temperature is 160 C (typical). If the temperature returns to 140 C, the ZLED7002 turns on and continues normal operation. 2.5.2. Main LED Short-Circuit Protection The ZLED7002 will detect a short-circuit on the MAIN LED. In this case, the ZLED7002 automatically turns off the MAIN LED channel and activates the SUB LED channel. 2016 Integrated Device Technology, Inc. 8 April 20, 2016
3 Application Circuit Design 3.1. Applications The ZLED7002 is designed for small battery-powered lighting life-time critical applications. Capable of operating efficiently with DC voltage supplies ranging from 2.7V to 5.5V, it is ideal for small portable lighting applications. Typical applications include helmet lighting, head/tail lights for bicycles, miner lamps, pocket lights, and various other general purpose low-voltage industrial and consumer LED applications. Figure 3.1 Basic ZLED7002 Application Circuit 2.7 to 5.5 V + DC - R1 ZLED7002 VCC SUB D1 R4 SUB LED MAIN LED UV MAIN Iset GND C1 R2 R3 NC NC SW1 3.2. Application Circuit Layout Requirements The following guidelines are strongly recommended when laying out application circuits: Use a 0.1μf capacitor connected between the UV pin and ground to minimize noise picked up on the UV pin. Place the capacitor close to the UV pin. If the application includes a switch as shown in Figure 3.1, locate it at the lowest voltage point to avoid sparks when switching. Use traces that are as short and wide as possible for any traces leading to actual ground that occur between the GND pin and Iset pin. This improves accuracy for the MAIN LED current and the under-voltage threshold. Also see Table 5.1 for connection requirements. 2016 Integrated Device Technology, Inc. 9 April 20, 2016
4 ESD Protection All pins have an ESD protection of ±4000V according the Human Body Model (HBM). The ESD test follows the Human Body Model with 1.5 kω/100 pf based on MIL 883-G, Method 3015.7. 5 Pin Configuration and Package Figure 5.1 ZLED7002 Pin Configuration Vcc SUB UV MAIN Iset GND NC NC Table 5.1 ZLED7002 Pin Descriptions and Connection Requirements SOP8 Package Pin No. Description (Also see section 3.2 for layout guidelines) V CC 1 Power supply (2.7V to 5.5V). UV 2 Under-voltage detection input. I SET 3 Input for external resistor that sets the current for the MAIN LED channel. NC 4 No connection. NC 5 No connection. GND 6 Connect to ground. MAIN 7 MAIN channel constant current source. Connect to cathode of MAIN LED. SUB 8 SUB channel current sink. Connect to cathode of D1 (Zener diode) connected to cathode of SUB LED. 2016 Integrated Device Technology, Inc. 10 April 20, 2016
Figure 5.2 SOP8 Package Drawing Table 5.2 SOP8 Package Dimensions Dimension (mm) Dimension (mm, except θ) Symbol Symbol Min Max Min Max A 1.350 1.750 E 3.800 4.000 A1 0.100 0.250 E1 5.800 6.240 A2 1.450 Typical e 1.270 Typical b 0.350 0.490 L 0.400 1.270 c 0.178 0.250 θ 0 8 D 4.800 5.000 2016 Integrated Device Technology, Inc. 11 April 20, 2016
6 Ordering Information Product Sales Code Description Package ZLED7002ZI1R ZLED7002 Toggle (Side-Step) Dual-Channel LED Driver SOP8 (Tape & Reel) ZLED7002KIT-E1 ZLED7002 Evaluation Kit Kit 7 Document Revision History Revision Date Description 1.0 15 July, 2011 First issue. April 20, 2016 Changed to IDT branding. Corporate Headquarters 6024 Silver Creek Valley Road San Jose, CA 95138 www.idt.com Sales 1-800-345-7015 or 408-284-8200 Fax: 408-284-2775 www.idt.com/go/sales Tech Support www.idt.com/go/support DISCLAIMER Integrated Device Technology, Inc. (IDT) reserves the right to modify the products and/or specifications described herein at any time, without notice, at IDT's sole discretion. Performance specifications and operating parameters of the described products are determined in an independent state and are not guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the suitability of IDT's products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property rights of IDT or any third parties. IDT's products are not intended for use in applications involving extreme environmental conditions or in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT. Integrated Device Technology, IDT and the IDT logo are trademarks or registered trademarks of IDT and its subsidiaries in the United States and other countries. Other trademarks used herein are the property of IDT or their respective third party owners. For datasheet type definitions and a glossary of common terms, visit www.idt.com/go/glossary. All contents of this document are copyright of Integrated Device Technology, Inc. All rights reserved. 2016 Integrated Device Technology, Inc. 12 April 20, 2016