Cylindrical Proximity Sensor E2A Safe Mounting with Greater Sensing Distance Ensures a sensing distance approximately 1. to 2 times larger than that of any conventional OMRON Sensor. Problems such as the collision of workpieces are eliminated. Full range of standard sizes (M8, M12, M18 and M; both long and short barrels) Modular construction simplifies customization. Ordering Information Size Sensing distance Connection Body material M8 Shielded 2. mm Pre-wired Stainless steel M12 connector M8 connector (- pin) Thread length (overall length) Output configuration Operation mode NO Operation mode NC 27 () PNP E2A-S8KS2-WP-B1 2M E2A-S8KS2-WP-B2 2M NPN E2A-S8KS2-WP-C1 2M E2A-S8KS2-WP-C2 2M 9 (62) PNP E2A-S8LS2-WP-B1 2M E2A-S8LS2-WP-B2 2M NPN E2A-S8LS2-WP-C1 2M E2A-S8LS2-WP-C2 2M Stainless 27 () PNP E2A-S8KS2-M1-B1 E2A-S8KS2-M1-B2 steel NPN E2A-S8KS2-M1-C1 E2A-S8KS2-M1-C2 9 (6) PNP E2A-S8LS2-M1-B1 E2A-S8LS2-M1-B2 NPN E2A-S8LS2-M1-C1 E2A-S8LS2-M1-C2 27 () PNP E2A-M8KS2-M1-B1 E2A-M8KS2-M1-B2 NPN E2A-M8KS2-M1-C1 E2A-M8KS2-M1-C2 9 (6) PNP E2A-M8LS2-M1-B1 E2A-M8LS2-M1-B2 NPN E2A-M8LS2-M1-C1 E2A-M8LS2-M1-C2 Stainless steel Non-shielded. mm Pre-wired Stainless steel M12 connector M8 connector (- pin) 27 (9) PNP E2A-S8KS2-M-B1 E2A-S8KS2-M-B2 NPN E2A-S8KS2-M-C1 E2A-S8KS2-M-C2 9 (61) PNP E2A-S8LS2-M-B1 E2A-S8LS2-M-B2 NPN E2A-S8LS2-M-C1 E2A-S8LS2-M-C2 27 () PNP E2A-S8KN-WP-B1 2M E2A-S8KN-WP-B2 2M NPN E2A-S8KN-WP-C1 2M E2A-S8KN-WP-C2 2M 9 (62) PNP E2A-S8LN-WP-B1 2M E2A-S8LN-WP-B2 2M NPN E2A-S8LN-WP-C1 2M E2A-S8LN-WP-C2 2M Stainless 27 () PNP E2A-S8KN-M1-B1 E2A-S8KN-M1-B2 steel NPN E2A-S8KN-M1-C1 E2A-S8KN-M1-C2 9 (6) PNP E2A-S8LN-M1-B1 E2A-S8LN-M1-B2 NPN E2A-S8LN-M1-C1 E2A-S8LN-M1-C2 27 () PNP E2A-M8KN-M1-B1 E2A-M8KN-M1-B2 NPN E2A-M8KN-M1-C1 E2A-M8KN-M1-C2 9 (6) PNP E2A-M8LN-M1-B1 E2A-M8LN-M1-B2 NPN E2A-M8LN-M1-C1 E2A-M8LN-M1-C2 Stainless steel 27 (9) PNP E2A-S8KN-M-B1 E2A-S8KN-M-B2 NPN E2A-S8KN-M-C1 E2A-S8KN-M-C2 9 (61) PNP E2A-S8LN-M-B1 E2A-S8LN-M-B2 NPN E2A-S8LN-M-C1 E2A-S8LN-M-C2 E2A Cylindrical Proximity Sensor 1
Size Sensing distance Connection Body material Thread length (overall length) Output configuration Operation mode NO Operation mode NC M12 Shielded. mm Pre-wired () PNP E2A-M12KS-WP-B1 2M E2A-M12KS-WP-B2 2M NPN E2A-M12KS-WP-C1 2M E2A-M12KS-WP-C2 2M 6 (72) PNP E2A-M12LS-WP-B1 2M E2A-M12LS-WP-B2 2M NPN E2A-M12LS-WP-C1 2M E2A-M12LS-WP-C2 2M M12 connector (8) PNP E2A-M12KS-M1-B1 E2A-M12KS-M1-B2 NPN E2A-M12KS-M1-C1 E2A-M12KS-M1-C2 6 (7) PNP E2A-M12LS-M1-B1 E2A-M12LS-M1-B2 NPN E2A-M12LS-M1-C1 E2A-M12LS-M1-C2 Non-shielded 8. mm Pre-wired () PNP E2A-M12KN8-WP-B1 2M E2A-M12KN8-WP-B2 2M NPN E2A-M12KN8-WP-C1 2M E2A-M12KN8-WP-C2 2M 6 (72) PNP E2A-M12LN8-WP-B1 2M E2A-M12LN8-WP-B2 2M NPN E2A-M12LN8-WP-C1 2M E2A-M12LN8-WP-C2 2M M12 connector (8) PNP E2A-M12KN8-M1-B1 E2A-M12KN8-M1-B2 NPN E2A-M12KN8-M1-C1 E2A-M12KN8-M1-C2 6 (7) PNP E2A-M12LN8-M1-B1 E2A-M12LN8-M1-B2 NPN E2A-M12LN8-M1-C1 E2A-M12LN8-M1-C2 M18 Shielded 8. mm Pre-wired 9 (9) PNP E2A-M18KS8-WP-B1 2M E2A-M18KS8-WP-B2 2M NPN E2A-M18KS8-WP-C1 2M E2A-M18KS8-WP-C2 2M 61 (81) PNP E2A-M18LS8-WP-B1 2M E2A-M18LS8-WP-B2 2M NPN E2A-M18LS8-WP-C1 2M E2A-M18LS8-WP-C2 2M M12 connector 9 () PNP E2A-M18KS8-M1-B1 E2A-M18KS8-M1-B2 NPN E2A-M18KS8-M1-C1 E2A-M18KS8-M1-C2 61 (7) PNP E2A-M18LS8-M1-B1 E2A-M18LS8-M1-B2 NPN E2A-M18LS8-M1-C1 E2A-M18LS8-M1-C2 Non-shielded 16. mm Pre-wired 9 (9) PNP E2A-M18KN16-WP-B1 2M E2A-M18KN16-WP-B2 2M NPN E2A-M18KN16-WP-C1 2M E2A-M18KN16-WP-C2 2M 61 (81) PNP E2A-M18LN16-WP-B1 2M E2A-M18LN16-WP-B2 2M NPN E2A-M18LN16-WP-C1 2M E2A-M18LN16-WP-C2 2M M12 connector 9 () PNP E2A-M18KN16-M1-B1 E2A-M18KN16-M1-B2 NPN E2A-M18KN16-M1-C1 E2A-M18KN16-M1-C2 61 (7) PNP E2A-M18LN16-M1-B1 E2A-M18LN16-M1-B2 NPN E2A-M18LN16-M1-C1 E2A-M18LN16-M1-C2 M Shielded 1. mm Pre-wired (6) PNP E2A-MKS1-WP-B1 2M E2A-MKS1-WP-B2 2M NPN E2A-MKS1-WP-C1 2M E2A-MKS1-WP-C2 2M 66 (86) PNP E2A-MLS1-WP-B1 2M E2A-MLS1-WP-B2 2M NPN E2A-MLS1-WP-C1 2M E2A-MLS1-WP-C2 2M M12 connector (8) PNP E2A-MKS1-M1-B1 E2A-MKS1-M1-B2 NPN E2A-MKS1-M1-C1 E2A-MKS1-M1-C2 66 (8) PNP E2A-MLS1-M1-B1 E2A-MLS1-M1-B2 NPN E2A-MLS1-M1-C1 E2A-MLS1-M1-C2 Non-shielded 2. mm Pre-wired (6) PNP E2A-MKN2-WP-B1 2M E2A-MKN2-WP-B2 2M (See note.) NPN E2A-MKN2-WP-C1 2M E2A-MKN2-WP-C2 2M. mm 66 (86) PNP E2A-MLN-WP-B1 2M E2A-MLN-WP-B2 2M NPN E2A-MLN-WP-C1 2M E2A-MLN-WP-C2 2M 2. mm M12 connector (8) PNP E2A-MKN2-M1-B1 E2A-MKN2-M1-B2 (See note.) NPN E2A-MKN2-M1-C1 E2A-MKN2-M1-C2. mm 66 (8) PNP E2A-MLN-M1-B1 E2A-MLN-M1-B2 NPN E2A-MLN-M1-C1 E2A-MLN-M1-C2 Note: M non-shielded Models with double sensing distance and short barrels cannot be mounted due to the necessary separation distance from the surrounding metal. Standard sensing models are thus available. 2 E2A Cylindrical Proximity Sensor
Model Number Legend E2A@-@@@@@-@-@@-@@ 1 2 6 7 8 9 11 12 Example: E2A-M12LS-M1-B1 Standard, M12, long barrel, shielded, Sn= mm, M12 connector, PNP-NO E2A-M8KN-WP-B1 M Standard, M8, short barrel, non-shielded, Sn= mm, pre-wired PVC cable, PNP-NO, cable length= m 1. Basic name 8. Kind of connection E2A WP: Pre-wired, PVC 2. Sensing technology M1: M12 connector (-pole) Blank: Standard double distance M: M8 connector (-pole). Housing shape and material M: M8 connector (-pole) M: Cylindrical, metric threaded, brass 9. Power source and output S: Cylindrical, metric threaded, stainless steel B: DC, -wire, PNP open collector. Housing size C: DC, -wire, NPN open collector 8: 8 mm D: DC, 2-wire 12: 12 mm E: DC, -wire, NPN voltage output 18: 18 mm F: DC, -wire, PNP voltage output : mm.operation mode. Barrel length 1: Normally open (NO) K: Standard length 2: Normally closed (NC) L: Long body 11.Specials (e.g., cable material, oscillating frequency) 6. Shield S: Shielded 12.Cable length N: Non-shielded Blank: Connector type 7. Sensing distance Numeral: Cable type Numeral: Sensing distance: e.g. 2=2 mm, 16=16 mm E2A Cylindrical Proximity Sensor
Specifications DC -wire Models Item Size M8 M12 Type Shielded Non-shielded Shielded Non-shielded E2A-M8@S2-M1-B1 E2A-M8@S2-M1-B2 E2A-M8@S2-M1-C1 E2A-M8@S2-M1-C2 E2A-S8@S2-@@-B1 E2A-S8@S2-@@-B2 E2A-S8@S2-@@-C1 E2A-S8@S2-@@-C2 E2A-M8@N-M1-B1 E2A-M8@N-M1-B2 E2A-M8@N-M1-C1 E2A-M8@N-M1-C2 E2A-S8@N-@@-B1 E2A-S8@N-@@-B2 E2A-S8@N-@@-C1 E2A-S8@N-@@-C2 E2A-M12@S-@@-B1 E2A-M12@S-@@-B2 E2A-M12@S-@@-C1 E2A-M12@S-@@-C2 E2A-M12@N8-@@-B1 E2A-M12@N8-@@-B2 E2A-M12@N8-@@-C1 E2A-M12@N8-@@-C2 Sensing distance 2 mm % mm % mm % 8 mm % Setting distance to 1.6 mm to.2 mm to.2 mm to 6. mm Differential travel % max. of sensing distance Target Ferrous metal (The sensing distance decreases with non-ferrous metal.) Standard target (mild steel ST7) 8 8 1 mm 12 12 1 mm 12 12 1 mm 2 2 1 mm Response frequency 1, Hz 1, Hz 1, Hz 8 Hz Power supply voltage (operating voltage range) Current consumption (DC -wire) Output type Control output 12 to 2 VDC. Ripple (p-p): % max. ( to 2 VDC) ma max. -B models: PNP open collector -C models: NPN open collector Load current 2 ma max. (2 VDC max.) (See note 2.) Residual voltage 2 V max. (under load current of 2 ma with cable length of 2 m) Indicator Operation mode (with sensing object approaching) Protection circuit Operation indicator (Yellow LED) -B1/-C1 models: NO -B2/-C2 models: NC For details, refer to the timing charts. Power source circuit reverse polarity protection, Surge suppressor, Short-circuit protection Output reverse polarity protection, Power source circuit reverse polarity protection, Surge suppressor, Short-circuit protection Ambient air temperature Operating: C to 7 C, Storage: C to 8 C (with no icing or condensation) Temperature influence (See note 2.) % max. of sensing distance at 2 C within temperature range of 2 C to 7 C 1% max. of sensing distance at 2 C within temperature range of C to 7 C Ambient humidity Operating: % to 9%, Storage: % to 9% Voltage influence 1% max. of sensing distance in rated voltage range 1% Insulation resistance M min. (at VDC) between current carry parts and case Dielectric strength 1, VAC at /6 Hz for 1 min between current carry parts and case Vibration resistance to Hz, 1.-mm double amplitude for 2 hours each in, Y and Z directions Shock resistance m/s 2, times each in, Y and Z directions 1, m/s 2, times each in, Y and Z directions Standard and listings IEC629: IP67, Degree of protection EN697--2: EMC UL (CSA) [E196] (See note.) Connection method -WP models: Pre-wired models (Standard length: 2 m) -M1 models: M12 -pin connector models -M models: M8 -pin connector models Weight Pre-wired model Approx. 6 g Approx. 8 g (packaged) M12 connector model M12 connector models: Approx. 2 g Approx. g M8 connector models: Approx. 1 g Material Case Stainless steel or brass-nickel plated -nickel plated Sensing surface PBT Cable PVC Clamping nut -nickel plated Note 1. The response frequency is an average value. Measurement conditions are as follows: standard target, a distance of twice the standard target distance between targets, and a setting distance of half the sensing distance. 2. When using any model at an ambient temperature between C and 2 C and a power voltage between and 2 VDC, use a load current of ma max.,. UL (CSA) [E196]: Use class 2 circuit only. E2A Cylindrical Proximity Sensor
DC -wire Models Item Size M18 M Type Shielded Non-shielded Shielded Non-shielded Non-shielded E2A-M18@S8-@@-B1 E2A-M18@S8-@@-B2 E2A-M18@S8-@@-C1 E2A-M18@S8-@@-C2 E2A-M18@N16-@@-B1 E2A-M18@N16-@@-B2 E2A-M18@N16-@@-C1 E2A-M18@N16-@@-C2 E2A-M@S1-@@-B1 E2A-M@S1-@@-B2 E2A-M@S1-@@-C1 E2A-M@S1-@@-C2 E2A-MKN2-@@-B1 E2A-MKN2-@@-B2 E2A-MKN2-@@-C1 E2A-MKN2-@@-C2 E2A-MLN-@@-B1 E2A-MLN-@@-B2 E2A-MLN-@@-C1 E2A-MLN-@@-C2 Sensing distance 8 mm % 16 mm % 1 mm % 2 mm % mm % Setting distance to 6. mm to 12.8 mm to 12 mm to 16 mm to 2 mm Differential travel % max. of sensing distance Target Ferrous metal (The sensing distance decreases with non-ferrous metal.) Standard target 2 2 1 mm 8 8 1 mm 1 mm 6 6 1 mm 9 9 1 mm (mild steel ST7) Response frequency Hz Hz 2 Hz Hz Hz Power supply voltage (operating voltage range) Current consumption (DC -wire) Output type Control output 12 to 2 VDC. Ripple (p-p): % max. ( to 2 VDC) ma max. -B models: PNP open collector -C models: NPN open collector Load current (See 2 ma max. (2 VDC max.) note 2.) Residual voltage 2 V max. (under load current of 2 ma with cable length of 2 m) Indicator Operation mode (with sensing object approaching) Protection circuit Operation indicator (Yellow LED) -B1/-C1 models: NO -B2/-C2 models: NC For details, refer to the timing charts. Output reverse polarity protection, Power source circuit reverse polarity protection, Surge suppressor, Short-circuit protection Ambient air temperature Operating: C to 7 C, Storage: C to 8 C (with no icing or condensation) Temperature influence (See note 2.) % max. of sensing distance at 2 C within temperature range of 2 C to 7 C 1% max. of sensing distance at 2 C within temperature range of C to 7 C Ambient humidity Operating: % to 9%, Storage: % to 9% Voltage influence 1% max. of sensing distance in rated voltage range 1% Insulation resistance M min. (at VDC) between current carry parts and case Dielectric strength 1, VAC at /6 Hz for 1 min between current carry parts and case Vibration resistance to Hz, 1.-mm double amplitude for 2 hours each in, Y and Z directions Shock resistance 1, m/s 2, times each in, Y and Z directions Standard and listings IEC629: IP67, Degree of protection EN697--2: EMC UL (CSA) [E196] (See note.) Connection method -WP models: Pre-wired models (Standard length: 2 m) -M1 models: M12 -pin connector models -M models: M8 -pin connector models Weight Pre-wired model Approx. 16 g Approx. 28 g Approx. 28 g Approx. 7 g (packaged) M12 connector model Approx. 7 g Approx. 2 g Approx. 2 g Approx. 26 g Material Case -nickel plated Sensing surface PBT Cable PVC Clamping nut -nickel plated Note 1. The response frequency is an average value. Measurement conditions are as follows: standard target, a distance of twice the standard target distance between targets, and a setting distance of half the sensing distance. 2. When using any model at an ambient temperature between - C and -2 C and a power voltage between and 2 VDC, use a load current of ma max.. UL (CSA) [E196]: Use class 2 circuit only. E2A Cylindrical Proximity Sensor
Engineering Data Operating Range (Typical) Shielded Models 18 16 1 12 Y 8 6 2 E2A-M@S1 E2A-M18@S8 E2A-M12@S E2A-S8@S2/ E2A-M8@S2 Non-shielded Models Y 2 2 1 E2A-MLN E2A-MKN2 E2A-M18@N16 E2A-M12@N8 E2A-S8@N/ E2A-M8@N 2 2 2 2 Distance Y (mm) Distance Y (mm) Influence of Sensing Object Size and Materials Shielded Models E2A-S8@S2/M8@S2 E2A-M12@S E2A-M18@S8 2.. 8. t = 1 mm t = 1 mm 7. 2.. 6. Stainless steel Stainless steel (SUS) (SUS). 1.. 1.. 2. 1... 2. 1. t = 1 mm Stainless steel (SUS) 1 2 2 1 2 2 2 6 E2A-M@S1 2 16 12 8 t = 1 mm Stainless steel (SUS) 2 6 7 8 6 E2A Cylindrical Proximity Sensor
Non-shielded Models E2A-S8@N/M8@N. t = 1 mm.. 2. 1. Stainless steel (SUS) E2A-M12@N8 t = 1 mm 8 6 2 Stainless steel (SUS) E2A-M18@N16 2 t = 1 mm 16 12 8 Stainless steel (SUS) 2 2 2 6 8 E2A-MKN2 2 t = 1 mm 2 1 Stainless steel (SUS) E2A-MLN t = 1 mm 2 2 1 Stainless steel (SUS) 2 6 8 2 6 8 E2A Cylindrical Proximity Sensor 7
Operation PNP Output Operation mode Model Timing chart Output circuit NO E2A-@-@-B1 Non-sensing zone Sensing object (%) Rated sensing distance Sensing zone Proximity Sensor ON Yellow indicator OFF ON Control output OFF Proximity Sensor main circuits Brown Black Blue Load Note 1: With M8 connector models, there is no output reverse polarity protection diode. +V V M12 Connector Pin Arrangement (See note 2.) M8 Connector Pin Arrangement 1 2 1 Note 2: Terminal 2 of the M12 connector is not used. NC E2A-@-@-B2 Non-sensing zone Sensing object (%) Rated sensing distance Sensing zone Proximity Sensor ON Yellow indicator OFF ON Control output OFF Proximity Sensor main circuits Brown Black (M8 connector: ) Blue Load Note 1: With M8 connector models, there is no output reverse polarity protection diode. +V V M12 Connector Pin Arrangement (See note 2.) M8 Connector Pin Arrangement 1 2 1 Note 2: Terminal of the M12 connector is not used. 8 E2A Cylindrical Proximity Sensor
NPN Output Operation mode Model Timing chart Output circuit NO E2A-@-@-C1 Non-sensing zone Sensing object (%) Rated sensing distance Sensing zone Proximity Sensor ON Yellow indicator OFF ON Control output OFF Proximity Sensor main circuits Brown Black Blue Load Note 1: With M8 connector models, there is no output reverse polarity protection diode. +V V M12 Connector Pin Arrangement (See note 2.) M8 Connector Pin Arrangement 1 2 1 Note 2: Terminal 2 of the M12 connector is not used. NC E2A-@-@-C2 Non-sensing zone Sensing object (%) Rated sensing distance Sensing zone Proximity Sensor ON Yellow indicator OFF Proximity Sensor main circuits Brown Black Blue Load +V (M8 connector: ) V ON Control output OFF Note 1: With M8 connector models, there is no output reverse polarity protection diode. M12 Connector Pin Arrangement (See note 2.) M8 Connector Pin Arrangement 1 2 1 Note 2: Terminal of the M12 connector is not used. E2A Cylindrical Proximity Sensor 9
Dimensions Note:All units are in millimeters unless otherwise indicated. Pre-wired Models (Shielded) Pre-wired Models (Non-shielded) E2A-S8KS2-WP-@@ 27 1 E2A-S8KN-WP-@@ 27 1 6.8 dia. Note 1. -dia. vinyl-insulated round cable with conductors (conductor cross section: Note 1. -dia. vinyl-insulated round cable with conductors (conductor cross section: E2A-M12KS-WP-@@. 17 7 E2A-M12KN8-WP-@@ 17 7. 7 9.2 dia. Note 1. -dia. vinyl-insulated round cable with conductors (conductor cross section:. mm 2 ; insulator diameter: 1. mm); standard length: 2 m Note 1. -dia. vinyl-insulated round cable with conductors (conductor cross section: E2A-M18KS8-WP-@@ E2A-M18KN16-WP-@@ 2 9. 9 9 2 9. M18 1 Note 1. -dia. vinyl-insulated round cable with conductors (conductor cross section: 1.1 dia. M18 1 Note 1. -dia. vinyl-insulated round cable with conductors (conductor cross section:. mm 2 ; insulator diameter: 1. mm); standard length: 2 m E2A-MKS1-WP-@@ 6 6. E2A-MKN2-WP-@@ 6. 6 1 M 1. Note 1. -dia. vinyl-insulated round cable with conductors (conductor cross section: 26. dia. M 1. Note 1. -dia. vinyl-insulated round cable with conductors (conductor cross section: E2A Cylindrical Proximity Sensor
E2A-S8LS2-WP-@@ 1 62 9 E2A-S8LN-WP-@@ 1 6 62 9.8 dia. Note 1. -dia. vinyl-insulated round cable with conductors (conductor cross section: Note 1. -dia. vinyl-insulated round cable with conductors (conductor cross section: E2A-M12LS-WP-@@ E2A-M12LN8-WP-@@ 72. 72. 17 6 7 17 7 6 7 9.2 dia. Note 1. -dia. vinyl-insulated round cable with conductors (conductor cross section: E2A-M18LS8-WP-@@ 81. 61 2 Note 1. -dia. vinyl-insulated round cable with conductors (conductor cross section: E2A-M18LN16-WP-@@ 2 81. 61 M18 1 Note 1. -dia. vinyl-insulated round cable with conductors (conductor cross section: E2A-MLS1-WP-@@ 86. 66 6 6 1.1 dia. E2A-MLN-WP-@@ M18 1 1 66 86. Note 1. -dia. vinyl-insulated round cable with conductors (conductor cross section: 26. dia. M 1. M 1. Note 1. -dia. vinyl-insulated round cable with conductors (conductor cross section: Note 1. -dia. vinyl-insulated round cable with conductors (conductor cross section: Mounting Hole Cutout Dimensions F External diameter of Proximity Sensor Dimension F (mm) M8 8. dia. +. M12 M18 M 12. dia. +. 18. dia. +.. dia. +. E2A Cylindrical Proximity Sensor 11
M12 Connector Models (Shielded) M12 Connector Models (Non-shielded) E2A-S8KS2-M1-@@ E2A-M8KS2-M1-@@ E2A-S8KN-M1-@@ E2A-M8KN-M1-@@ 1 27 1 6 27 6 dia. Note: Operation indicator (yellow LED, 9 ) Note: Operation indicator (yellow LED, 9 ) E2A-M12KS-M1-@@ E2A-M12KN8-M1-@@ 8 8 17 7 17 7 7 9. dia. Note: Operation indicator (yellow LED, 9 ) Note: Operation indicator (yellow LED, 9 ) E2A-M18KS8-M1-@@ E2A-M18KN16-M1-@@ 2 9 9 2 M18 1 Note: Operation indicator (yellow LED, 9 ) 1. dia. M18 1 Note: Operation indicator (yellow LED, 9 ) E2A-MKS1-M1-@@ 8 6 E2A-MKN2-M1-@@ 6 1 8 26.6 dia. M 1. Note: Operation indicator (yellow LED, 9 ) M 1. Note: Operation indicator (yellow LED, 9 ) 12 E2A Cylindrical Proximity Sensor
E2A-S8LS2-M1-@@ E2A-M8LS2-M1-@@ 1 6 9 E2A-S8LN-M1-@@ E2A-M8LN-M1-@@ 1 6 6 9 6 dia. Note: Operation indicator (yellow LED, 9 ) Note: Operation indicator (yellow LED, 9 ) E2A-M12LS-M1-@@ 17 6 7 7 E2A-M12LN-M1-@@ 17 7 7 6 7 9.2 dia. Note: Operation indicator (yellow LED, 9 ) Note: Operation indicator (yellow LED, 9 ) E2A-M18LS8-M1-@@ 2 61 7 7 61 2 E2A-M18LN16-M1-@@ 1.1 dia. E2A-MLS1-M1-@@ M18 1 Note: Operation indicator (yellow LED, 9 ) 8 66 6 E2A-MLN-M1-@@ 6 M18 1 Note: Operation indicator (yellow LED, 9 ) 8 66 1 26.6 dia. M 1. M 1. Note: Operation indicator (yellow LED, 9 ) Note: Operation indicator (yellow LED, 9 ) M8 Connector Models (Shielded) M8 Connector Models (Non-shielded) E2A-S8KS2-M-@@ E2A-S8KN-M-@@ 1 9 27 9 27 1 6.8 dia. Note: Operation indicator (yellow LED, 9 ) Note: Operation indicator (yellow LED, 9 ) E2A-S8LS2-M-@@ E2A-S8LN-M-@@ 1 61 9 61 9 1 6.8 dia. Note: Operation indicator (yellow LED, 9 ) Note: Operation indicator (yellow LED, 9 ) E2A Cylindrical Proximity Sensor 1
Precautions Safety Precautions Power Supply Do not impose an excessive voltage on the E2A, otherwise it may be damaged. Do not impose AC current ( to 2 VAC) on any DC model, otherwise it may be damaged. Load Short-circuit Do not short-circuit the load, or the E2A may be damaged. The E2A s short-circuit protection function will be valid if the polarity of the supply voltage imposed is correct and within the rated voltage range. Correct Use Designing Power Reset Time The Proximity Sensor is ready to operate within ms after power is supplied. If power supplies are connected to the Proximity Sensor and load respectively, be sure to supply power to the Proximity Sensor before supplying power to the load. Effects of Surrounding Metal When mounting the E2A within a metal panel, ensure that the clearances given in the following table are maintained. l Wiring Be sure to wire the E2A and load correctly, otherwise it may be damaged. Connection with No Load Be sure to insert loads when wiring. Make sure to connect a proper load to the E2A in operation, otherwise it may damage internal elements. Do not expose the product to flammable or explosive gases. Do not disassemble, repair, or modify the product. Power OFF The Proximity Sensor may output a pulse signal when it is turned OFF. Therefore, it is recommended that the load be turned OFF before turning OFF the Proximity Sensor. Power Supply Transformer When using a DC power supply, make sure that the DC power supply has an insulated transformer. Do not use a DC power supply with an auto-transformer. Mutual Interference When installing two or more Sensors face-to-face or side-by-side, ensure that the minimum distances given in the following table are maintained. Type Dimension M8 M12 M18 M Shielded l (See note 1.) m m. 12 2 d --- --- 27 D 1. n 12 18 27 Short barrel (Unit: mm) Long barrel (See note 2.) l 12 1 22 m 8 2 8 7 9 d 2 7 9 12 D 12 1 22 n 2 7 9 12 Note 1. In the case of using the supplied nuts. If true flash mounting is necessary, apply a free zone of 1. mm. 2. In the case of using the supplied nuts. If true flush mounting is necessary, apply a free zone of mm. D d dia. l n m Type Dimension M8 M12 M18 M Short barrel (Unit: mm) Long barrel Nonshielded Shielded A 2 6 1 B 1 2 7 Nonshielded A 8 12 2 B 6 12 2 1 E2A Cylindrical Proximity Sensor
Wiring High-tension Lines Wiring through Metal Conduit: If there is a power or high-tension line near the cable of the Proximity Sensor, wire the cable through an independent metal conduit to prevent against Proximity Sensor damage or malfunctioning. Cable Extension Standard cable length is less than 2 m. The tractive force is N. Mounting The Proximity Sensor must not be subjected to excessive shock with a hammer when it is installed, otherwise the Proximity Sensor may be damaged or lose its water-resistivity. Do not tighten the nut with excessive force. A washer must be used with the nut. Maintenance and Inspection Periodically perform the following checks to ensure stable operation of the Proximity Sensor over a long period of time. 1. Check for mounting position, dislocation, looseness, or distortion of the Proximity Sensor and sensing objects. 2. Check for loose wiring and connections, improper contacts, and line breakage.. Check for attachment or accumulation of metal powder or dust.. Check for abnormal temperature conditions and other environmental conditions.. Check for proper lighting of indicators (for models with a set indicator.) Never disassemble or repair the Sensor. Environment Water Resistivity Do not use the Proximity Sensor underwater, outdoors, or in the rain. M8 M12 M18 M Type Torque Stainless steel type 9 Nm type Nm Nm 7 Nm 18 Nm Operating Environment Be sure to use the Proximity Sensor within its operating ambient temperature range and do not use the Proximity Sensor outdoors so that its reliability and life expectancy can be maintained. Although the Proximity Sensor is water resistive, a cover to protect the Proximity Sensor from water or water-soluble machining oil is recommended so that its reliability and life expectancy can be maintained. Do not use the Proximity Sensor in an environment with chemical gas (e.g., strong alkaline or acid gasses including nitric, chromic, and concentrated sulfuric acid gases). Inrush Current A load that has a large inrush current (e.g., a lamp or motor) will damage the Proximity Sensor, in which case connect the load to the Proximity Sensor through a relay. E2A Cylindrical Proximity Sensor 1
<SUITABILITY FOR USE> OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of the products in the customer s application or use of the products. Take all necessary steps to determine the suitability of the product for the systems, machines, and equipment with which it will be used. <CHANGE IN SPECIFICATIONS> Product specifications and accessories may be changed at any time based on improvements and other reasons. Consult with your OMRON representative at any time to confirm actual specifications of purchased product. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by.97. To convert grams into ounces, multiply by.27. Cat. No. D96-E1-1 OMRON Corporation Industrial Automation Company Industrial Sensors Division Sensing Devices and Components Division H.Q. -2, Narutani, Nakamyama-cho, Ayabe-shi, Kyoto, 62- Japan Tel: (81)77--78/Fax: (81)77-- 16 In the interest of product improvement, specifications are subject to change without notice.