STANDARD FEATURES with MXP-200FB (FANUC-32i) POWERFUL 30 HP SPINDLE OUTPUT HIGH SPEED 30 TOOL SWING-ARM ATC SYSTEM HIGH PRECISION CERAMIC SPINDLE BEARINGS RANDOM ACCESS & BI-DIRECTIONAL ATC MAGAZINE IDD SPINDLE DESIGN WITH 12,000 RPM MAXIMUM 200 BLOCKS LOOK AHEAD, 2MS PROCESSING SPEED OIL-AIR MIST LUBRICATION FOR SPINDLE BEARINGS AI NANO CONTOUR CONTROL WITH ANTI JERK FUNCTION PRE-TENSIONED HARDENED & GROUND BALLSCREW AC DIGITAL SERVO & SPINDLE DRIVES VECTOR HRV3 E HIGH QUALITY & RUGGED MEEHANITE N CASTINGS ABSOLUTE ENCODERS W/ 1 MILLIONTHS PLUS RESOLUTION ULTRA RIGID THK LINEAR GUIDES WAY ON X,Y,Z 1280 METER OF MEMORY W/ 100MPS ETHERNET FUNCTION AUTOMATIC LUBRICATION SYSTEM PCMCIA SLOT FOR MEMORY EXPANSION & MODEM 380MM A/C ROTARY TABLE 10.4 LCD MONITOR W/ DYNAMIC GRAPHIC DISPLAY 4+1 CONTROLLED AXIS MOVEMENTS MANUAL GUIDE I CONVERSATIONAL SOFTWARE SPINDLE AIR CURTAIN & CUTTING AIR BLAST BELL SHAPED ACCELERATION & DECELERATION SPINDLE COOLING SYSTEM / CHILLER MACRO B & SKIP FUNCTION 99 GAL COOLANT SYSTEM HIGH SPEED RIGID TAPPING & HELICAL INTERPOLATION 3-D DYNAMIC TOOL PATH GRAPHICS BASIC SPECIFICATIONS HEADSTOCK Motor FANUC αt8 AC Digital Spindle Motor Horse Power 30 HP Maximum Speed 12,000 rpm Spindle Drive Isolated Direct Drive Spindle Spindle Nose to Table 2.76 21.65 Spindle Center to Z-axis Way Cover 20.03 TABLE Size ø14.96 / 380mm T-Slots number, width, pitch.47 Maximum Load 551 lbs. Table Height 44.09 ATC SYSTEM Tool Type CAT-40 (optional BBT-40) Tool Selection Bi-directional, Random Access Maximum Tool Weight 13.2 lbs. Maximum Tool Length 11.84 Maximum Tool Diameter 3.54 / 4.9 (when adjacent pocket is empty) Magazine Tool Capacity 30 Tools (40/60 optional) Tool Change Time (Approx.) 3.5 sec. (T-T) / 5 sec. (C-C) AXES SPECIFICATIONS Travel Positioning Repeatability Rapid Rate / Cutting Feed X Axis 27.56 0.00012 ± 0.0001 1418 ipm / 394 ipm Y Axis 20.47 0.00012 ± 0.0001 1418 ipm / 394 ipm Z Axis 19.9 0.00012 ± 0.0001 945 ipm / 394 ipm C Axis 360 deg. 28 sec. 16 sec. 33.3 rev/min A Axis +30/-120 deg. 28 sec. 16 sec. 33.3 rev/min
DETAILED SPECIFICATIONS HEADSTOCK TABLE Spindle Motor FANUC αt8i AC Digital Spindle Motor Horsepower 30 HP Spindle Drive Isolated Direct Drive Motor (patent pending) RPM Range 45 12,000 rpm Two Windings H/L Shifting Spindle Bearing Type Angular Contact Ceramic Bearings Bearing Class ABEC Class 7 (P4A) Spindle Taper Hardness / Material HRC62 o 1.5p / SCM21 Spindle Draw Bar Type Collet Style Retention System Helical Disc Spring Holding Force 2,025 2,700 lbs. Counter Balance Electronics Spindle Orientation Built-in Positioning Encoder Spindle Nose to Table 2.76 21.65 Spindle Center to Z-axis Way Cover 23.03 Dimensions: Diameter 14.96 T-Slots 8 x.47 Maximum Table Load 551 lbs. Height from Floor 44.09 AUTOMATIC TOOL CHANGER Changer Dual Swing Arm Type Tool Selection Method Bi-directional, Random Access Tool Shank CAT-40 (BBT-40 optional) Maximum Tool Weight 13.2 lbs Maximum ATC Weight 264 lbs. Maximum Tool Length 11.02 Max tool Dia. Adjacent Pocket full 2.99 Max tool Dia. Adjacent Pocket Empty 4.9 Max number of tools (opt.) 30 tools (40T / 60T ) Tool Change Time 3.5 Seconds (tool to tool) 5 seconds (chip to chip)
DETAILED SPECIFICATIONS (continued) X AXIS Ball Screw Diameter 1.57 Ball Screw Class JIS C3 Ball Screw Pitch 0.47 Rapid Feedrate 1,417.32 ipm Cutting Feedrate 393.70 ipm Travel 27.56 Positioning (JIS 6338) 0.0001 Repeatability (JIS 6338) ±0.0001 Horsepower 5.3 HP Thrust Force (Rated) 2,325 lbf Thrust Force (Max.) 6,763 lbf Y-AXIS Ball Screw Diameter 1.57 Ball Screw Class JIS C3 Ball Screw Pitch 0.47 Rapid Feedrate 1,417.32 ipm Cutting Feedrate 393.70 ipm Travel 20.47 Positioning (JIS 6338) 0.0001 Repeatability (JIS 6338) ±0.0001 Horsepower 5.3 HP Thrust Force (Rated) 2,325 lbf Thrust Force (Max.) 6,763 lbf Z-AXIS Ball Screw Diameter 1.57 Ball Screw Class JIS C3 Ball Screw Pitch 0.47 Rapid Feedrate 944.8 ipm Cutting Feedrate 393.70 ipm Travel 19.90 Positioning (JIS 6338) 0.0001 Repeatability (JIS 6338) ±0.0001 Horsepower 5.3 HP Thrust Force (Rated) 2,325 lbf Thrust Force (Max.) 6,763 lbf A/C-TABLE A Axis Tile 150 degree + 30/-120 C Axis Rotary 360 degree A/C Axis Feed Rate 33.3 rev/min / 33.3 rev/min A/C Positioning Accuracy 28 sec../ 28 sec. A/c Repeatability Accuracy 16 sec. / 16 sec.
SPECIFICATIONS Coolant Tank Capacity 99 gal. DIMENSIONS Floor Spacing (W x D x H) 87 x 103.3 x 120.5 Shipping (W x D x H) 140 x 95 x 111 WEIGHT Net Shipping 13,000 lbs. 14,500 lbs POWER REQUIREMENTS 208 VAC Line Voltage AC 3 Phase Breaker Size 125 AMPS Power Consumption 45KVA AIR REQUIREMENTS 78.2 psi GENERAL Machine Net Weight 13,000lbs. Shipping Weight 14,500lbs. Power Consumption 45 kva Floor Spacing (W x D x H) 87 x 103.3 x 120.5 Shipping Dimensions (W x D x H) 140 x 95 x 111 ACCESSORIES Standard Option Tool Kit Oil-mist Collector Work Lamp Chip Conveyor Pilot Lamp Tool setter Spindle Chiller Coolant Through Spindle System Full Chip Enclosure Chip Conveyor Coolant Gun Spindle Chiller Cooling System Air Gun Automatic Power Off Device Spindle Air Blast Auto Tool Length Measurement System Spindle Air Seal Data Server Central Lubrication System Guide way Cover (X/Y/Z)
YCM (MXP-200FB) / Fanuc 32i CONTROL SPECIFICATIONS I OPERATION PLUS SOFTWARE ENHANCEMENT EXCLUSIVELY FROM YCM HIGH PERFORMANCE AC DIGITAL SERVO & SPINDLE DRIVES HIGH RESPONSIVE VECTOR DRIVES ABSOLUTE POSITIONING ENCODERS HIGH RESOLUTION 10.4" LCD MONITOR AI CONTOUR CONTROL II WITH ANTI JERK FUNCTION 200 BLOCK LOOK AHEAD, 2MS PROCESSING SPEED CUSTOM MACRO B & SKIP FUNCTION BIG & DOUBLE SCREEN DISPLAY ANIMATION FOR MANUAL GUIDE i SOFTWARE 1,280 METERS (512K BYTE) MEMORY RS 232C INTERFACE & ETHERNET CONNECTION HIGH SPEED RIGID TAPPING ADDITIONAL WORK & TOOL OFFSETS HEAT EXCHANGER FOR ELECTRICAL CABINET PCMCIA EXPANSION SLOT POWER FAILURE MODULE CONTROLLED AXIS: TOTAL 5 AXES SIMULTANEOUSLY CONTROLLED AXIS: 4 AXES
MACHINE WORK AREAS DIMENSIONS
MACHINE DIMENSIONS