Name Answer Key Company Address City, State, Zip Instructor Date Your email User Name = Password = XR500/XR100 Command Processor Review 1. may be connected to the LX-Bus. a) Zone expanders c) Output expanders b) All of these d) Single point detectors 2 The panel's Yellow wire is the wire. a) Receive b) transmit c) auxiliary power d) smoke power 3 When a FIRE type zone is in ALARM, which account number is reported to central station? a) Area #1's account number c) Main Account number in Communication b) Area #0's account number d) No account number is sent 4 Select this communication type when you want the panel to send signals to the central monitoring station using a network connection. a) NET c) DD b) MPX d) CID 5 Zones 1 through 8 cannot detect conditions. a) Ground fault c) Shorted b) Open d) Normal 6 XR500 Series panel addresses are capable of handling four expansion zones when using DMP Security Command keypads or zone expander modules for a total of keypad bus expansion zones. a) 8 c) 16 b) 200 d) 64
7 Selecting the Adaptive option for a backup path to adapt to the check-in programming from this groups primary path if the primary path become unavailable. 8 The J1 Ethernet connector is not operational when the on-board RS-232 connection is enabled (XR500). 9 The DISPLAY AREA option in Device Setup allows 'area-grouping' and works in conjunction with Menu Display and Status List options. 10 The SCHEDULE CHANGE option allows the panel to send a report of all schedule changes. a) Output c) Opening and Closing b) Shift d) Lock and Unlock 11 The SWINGER BYPASS TRIPS option determines how many times a zone can trip in before the panel will automatically bypass the zone. a) 15minutes c) a Shift b) 30 minutes d) 60 minutes 12 The COMM FAIL OUTPUT will turn on when the panel has failed to communicate with the receiver after dial attempts. a) 3 b) 4 c) 7 d) 10 13 All programming changes will be lost if. a) The battery is not connected c) the STOP routine is not run b) The panel is not initialized d) programming is not done at keypad #1 14 When a device's DISPLAY AREA has areas 1 and 3, what happens when a user with Authority to disarm areas 1-32 disarms from the device? a) All areas are disarmed c) no areas are disarmed b) Only areas 1 and 3 are disarmed d) all disarm, but only 1 and 3 send reports 15 A 16-zone expander on LX Bus #1 is addressed 16. What would be the zone number for the FIFTH zone on this expander? a) 820 b) 520 c) 521 d) 821
16. When the keypad displays RESET PANEL, what must be done? a) J16 must be shorted c) panel must be powered down b) initialize programming d) keypad should be replaced 17. The maximum voltage drop between the panel and any device is. a) 12 VDC b) 2 VDC c) 2 VAC d) 5 VDC 18. The 3 rd zone connected to Keypad Bus address #3 is Zone Number. a) 3 b) 505 c) 33 d) 103 19. The 1 st zone connected to Keypad Bus address #8 is Zone Number. a) 11 b) 80 c) 81 d) 1 20. The LOCAL IP ADDRESS refers to the. a) the panel s IP address c) the receiver s IP address b) the network address d) none of these 21. The programming option provides supervision of the network communication path. a) SUB CODE b) CHECKIN c) FAIL TIME d) PASSPHRASE 22. There are 8 paths of communication 23. When manually configuring the panel to communicate over the network, you must know the Local IP, Remote IP and IP addresses. a) Server b) Trap Server c) Gateway d) icom 24. The CHECKIN MINS default time for NET is 200. 25. When DHCP is set to NO, the LOCAL IP ADDRESS is: a) static b) dynamic c) unchangeable d) temporary
Answer questions 26 35 using the information provided on page 5. 26. Which one of the areas is a Common Area? a) Area 1 b) Area 2 c) Area 3 d) Area 4 27. The door schedule for D2 is from: a) 9am to 5pm b) 8am to 4pm c) 24 hour d) None of the above 28. If the Access and Egress field are left blank, any valid code will be. a) granted b) denied 29. Each AREA to be used in the system must have. a) a name b) assigned zone c) access doors d) a schedule 30. The Warehouse Employees profile can only access the Warehouse (area 3) after the Warehouse (area 3) has been disarmed. 31. No profiles are allowed to arm the Break Room (area 4) because it is a common area. 32. What type of schedule is used to restrict access to certain individuals? a) Door Schedules b) Shift Schedules c) Area Schedules d) None of these 33. Anti-pass back has been enabled for Profile #11 and #12 because they have access to the vault which has access and egress requirements. 34. Profile #12, the Management Profile, can arm and disarm areas. a) 6, 7, 8 and 9 b) 1, 2, 3 and 5 c) all d) None of the above 35. Device 3 has an Access area. a) 1 b) 2 c) 3 d) 4
Information for questions 26 through 35 Area Area Name Auto Arm Auto Bad Zones Armed Late Output Common Area Information Disarm Output 1 LOBBY No No Bypass 0 0 No 2 OFFICE No No Bypass 0 0 No 3 WAREHOUSE No No Bypass 0 0 No 4 BREAK ROOM No No Bypass 0 0 Yes 5 VAULT No No Bypass 0 0 No DEVICE Name Access Egress SETUP Device 1 Keypad Device 2 Lobby Door 1 Device 3 Office Door 2 Device 4 Warehouse Door 3 Device 5 Vault Egress 5 Device 6 Vault Access 5 Device 7 Office / Whse Door 2 Door Schedule D2-8am-4pm
Area Schedule (Area schedules set to Yes ) Area 1- S1/ Open 8am-Close 5pm Area 2- S1/ Open 12:00am-Close 11:59pm Area 3- S1/ Open 12:00am-Close 11:59pm Area 4- S1/ Open 8am-Close 5pm PROFILES Profile # 11 ADMINISTRATOR Profile # 12 MANAGEMENT Profile # 13 CLEANING CREW Profile # 14 WAREHOUSE EMPLOYEES Arm/Disarm Areas 1 2 3 5 6 7 8 1 2 3 5 1 2 3 None Access Areas 1 2 3 5 6 7 8 1 2 3 5 1 2 3 3 Output Group 0 0 0 0 Arm / Disarm Yes Yes Yes No Alarm Silence Yes Yes Yes No Sensor Reset Yes Yes Yes No Door Access Yes Yes Yes Yes Armed Areas Yes Yes Yes No Outputs ON/OFF Yes No No No Zone Status Yes No No No Bypass Zones Yes No No No Zone Monitor Yes No No No System Status Yes No No No System Test Yes No No No Profiles Yes No No No User Codes Yes No No No Schedules Yes No No No Set Time Yes No No No Display Events Yes No No No Service Request Yes No No No Fire Drill Yes No No No Extend Schedules Yes No No No Temp Code No No No No Anti Passback Yes* Yes* No No Allow (ANY 1234) Anytime Shift 1 Shift 2 Shift 1 NOTE 1: Because profiles 11 and 12 have access to Area 5 (VAULT), we have enabled Anti-pass back for these profiles. NOTE 2: No profiles have authority to arm/disarm Area 4 because it is a COMMON AREA. LT-1012 (12/08) 2008 Digital Monitoring Products, Inc. *LT-1012*