WIRING DIAGRAMS. Installation and wiring of NVIROMON system NVIROMON MULIODCBPSU. Remote Environmental Monitoring and Control for IT equipment.
|
|
- Chastity Beatrix Shepherd
- 5 years ago
- Views:
Transcription
1 WIRING DIAGRAMS NVIROMON R12 Remote Environmental Monitoring and Control for IT equipment. NVIROMON MULIODCBPSU Installation and wiring of NVIROMON system
2 ITEMS Quantity Equipment 1 NVIROMON unit 4 Temperature & water probe 4 Flood sensors 1 Power cable 1 Door Controller and Multi IO unit with Battery and Battery Charger 1 Keypad / SAGEM biometric reader 1 Door contacts 1 Maglock 1 Exit Button 1 Break Glass 1 Fireman s Switch 1 Beacon Alarm flasher 1 Buzzer 1 Passive Infrared Sensor 1 Smoke Sensor 1 IP Camera 1 SMOTHER Third party requirements (Optional) A GSM SIM card is required to activate the GSM messaging and alert system of the NVIROMON unit. Any active GSM or prepaid GSM SIM card can be obtained from a local GSM service provider. Technical information Connector Information RJ45 RF MMCX IEC power inlet 1
3 Installation Procedure See attached wiring diagrams 1. The NVIROMON Server Room Outlay. (Page 5) 2. The NVIROMON is a 1U rack mountable unit. (Page 5) Mount the NVIROMON in an available 1U slot inside an allocated cabinet. 3. Power feed connection. (Page 5) Connect the IEC power inlet to an available 230VAC supply. Switch on the backup battery activation switch at the back of the unit. 4. GSM Sim card (optional) Ensure that the mains power feed is switched off and ensure that the backup battery switch, mounted on the back of the unit, is in the off position before fitting the SIM card into the SIM card slot at the front of the unit. Connect the GSM external antenna to the RF MMCX connector. 5. Multi IO unit with Battery and Battery Charger (Door Controller) (Diag. 1 Page 6) Place the unit at required location close to the access door. Connect the Power supply to an available 230VAC supply. The multi IO probe is inside the power supply enclosure. Connect the probe to the NVIROMON probe port with a CAT5 cable. Both ends of the CAT5 cable have RJ45 connectors. 6. Temperature and water probes (Diag. 2 Page 7) Place the two temperature and water probes at required locations. Connect the probes to the NVIROMON probe ports with CAT5 cables. Both ends of the CAT5 cable have RJ45 connectors. Note that DIP switches on probes are set from numbers 1 to Flood sensors (Diag. 2 Page 7) Place the four flood sensors at required locations. Connect the sensors to the temperature and water probe with CAT5 cables. Both ends of the CAT5 cable have RJ45 connectors. 8. DOOR switch (Diag. 3 Page 8) Install the Door switch at required location inside the access door. Connect to port 12 of the Multi IO unit inside the power supply enclosure. The CAT5 cable Connect the other end of the cable to the Door contacts according to diagram 3 on page 8. 2
4 9. EXIT button (Diag. 3 Page 8) Install the EXIT button at required location inside the access door. Connect to port 11 of the Multi IO unit inside the power supply enclosure. The CAT5 cable The CAT5 cable Connect the other end of the cable to the EXIT button according to diagram 3 on page Passive infrared (Diag. 4 Page 9) Install the PASSIVE INFRARED at required location inside the server room. Connect to port 16 of the Multi IO unit inside the power supply enclosure. The CAT5 cable The CAT5 cable Connect the other end of the cable to the PASSIVE INFRARED unit according to diagram 4 on page Smoke Sensor (Diag. 4 Page 9) Install the SMOKE SENSOR at required location inside the server room. Connect to port 10 of the Multi IO unit inside the power supply enclosure. The CAT5 cable The CAT5 cable Connect the other end of the cable to the SMOKE SENSOR unit according to diagram 4 on page BEACON Alarm (Diag. 5 Page 10) Install the BEACON alarm unit at required location outside and close to the access door. Connect to port 4 of the Multi IO unit inside the power supply enclosure. The CAT5 cable Connect the other end of the cable to the BEACON unit according to diagram 5 on page BUZZER Alarm (Diag. 5 Page 10) Install the BUZZER alarm unit at required location outside and close to the access door. Connect to port 8 of the Multi IO unit inside the power supply enclosure. The CAT5 cable Connect the other end of the cable to the BUZZER unit according to diagram 5 on page Fireman s Switch (Diag. 5 Page 10) Install the FIREMAN S SWITCH at required location inside/outside and close to the access door. Connect the Fireman s Switch contacts with a CAT5 cable to port 3 of the multi IO probe. The CAT5 cable connects to the multi IO probe with a RJ45 connector. Connect the other end of the cable to the KEY SWITCH connectors according to diagram 5 on page 10. 3
5 15. Key switch (Diag. 5 Page 10) Install the KEY SWITCH at required location outside and close to the access door. Connect the one KEY SWITCH contact with a cable to the contacts of the FIREMAN S SWITCH unit.according to diagram 5 on page 10. Connect the other KEY SWITCH contact with a cable to the contacts of the BREAK GLASS unit. according to diagram 5 on page 10. Connect the KEY SWITCH tamper contacts according to diagram 5 on page BREAK GLASS contacts (Diag. 5 Page 10) Install the BREAK GLASS contacts at required location inside and close to the access door. Connect the one BREAK GLASS contact with a cable to the negative connector of the MAGLOCK (magnetic lock) according to diagram 5 on page MAGLOCK (Diag. 5 Page 10) Install the MAGLOCK at required location inside the access door. Connect the the MAGLOCK contacts according to diagram 5 on page Keypad access control reader (Diag. 6 Page 11) Install the keypad unit at required location outside and close to the access door. Connect to port 3 of the Multi IO unit inside the power supply enclosure. The CAT5 cable Connect the other end of the cable to the keypad unit according to diagram 6 on page SAGEM Biometric Reader (Diag. 6 Page 11) Install the SAGEM reader at the required location outside and close to the access door. Connect to port 3 of the Multi IO unit inside the power supply enclosure. The CAT5 cable Connect the other end of the cable to the keypad unit according to diagram 6 on page 11. Connect the SAGEM ethernet connector to an ethernet port on a switch according to diagram 6 on page Fire protection SMOTHER (Diag. 7 Page 12) Install the SAGEM reader at the required location outside and close to the access door. Connect to port 3 of the Multi IO unit inside the power supply enclosure. The CAT5 cable Connect the other end of the cable to the keypad unit according to diagram 6 on page 11. Connect the SAGEM ethernet connector to an ethernet port on a switch according to diagram 6 on page Generator and UPS monitoring wiring (Page 13) 22. Remote Monitoring and Control System (Page 14) 23. NVIROMON PORT Layout and Pins (Page 15) 24. MULTI- IO PORT Layout and Pins (Page 16) 4
6 5
7 6
8 7
9 8
10 9
11 10
12 11
13 12
14 13
15 14
16 15
17 16
WIRING DIAGRAMS NVIROMON NDCNTRLRS485. Remote Environmental Monitoring and Control for IT equipment. NVIROMON
WIRING DIAGRAMS NVIROMON Remote Environmental Monitoring and Control for IT equipment. NVIROMON NDCNTRLRS485 Installation and wiring of NVIROMON system Items Quantity Equipment 1 NVIROMON unit 2 Temperature
More informationLab 5: Access Control Training Station
Lab 5: Access Control Training Station Learning Objectives At the end of the lab, trainees should be able to: 1. Understand the functional block and hardware of an access control system. 2. Understand
More informationSelf-Contained Equipment Cabinets
Self-Contained Equipment Cabinets The water and dust proof self-contained cabinets houses all the services required to service, power backup and protect your network core or distribution equipment required
More informationNetGen Hardware Installation Guide. for NetGen Ethernet Door Controllers
NetGen Hardware Installation Guide for NetGen Ethernet Door Controllers 0613 Table of Contents BLUEWAVE SYSTEM OVERVIEW...2 THE WI-FI LOCK AND SECURITY COMPANY...2 NETGEN DOOR CONTROLLERS...2 INSTALLATION
More informationFACIAL RECOGNITION TERMINAL SYSTEM
StoneLock is a global leader in designing and manufacturing secure access control solutions. We are proud to build and design the most secure, reliable and user-friendly access control products for both
More informationQuick Start Guide. SEB-710 I/O Expansion board. Introduction
SEB-710 I/O Expansion board Revision 1.0 - (March, 2011) Saflec Systems (Pty) Ltd Quick Start Guide Introduction The SEB-710 is an I/O expansion device for additional inputs and outputs. It has eight relay
More informationMicro Instruments price list All pricing excludes 15%
Micro Instruments price list All pricing excludes VAT @ 15% - 2019 Product Description Solar Smart R1 Solar MPPT regulator 12/24V - 20Amp with R2 799.00 5 Way Relay board R360.00 Ethernet + SNMP support
More informationPDU Solutions. PDU Solutions
Canovate offers a full range of PDU s from basic and metered ones to IP PDU s with per socket switching capability and wireless sensor connectivity. Our PDU s can be used in the most complex ISP and Colocation
More informationHUDGE STORAGE MEMORY TO CATER FOR FUTURE EXPANSION OPTO ISOLATION FOR BETTER NOISE PROTECTION
CUSTOMISED ENCLOSURE BEAT - 200 32 BIT CPU CONTROLLER 128MB INTERNAL MEMORY 2 x 16 CHARACTER LCD BACKLIGHT DISPLAY ISO 14443 TYPE A&B READ SUPPORTED MIFARE SUPPORTED MULTIPLE LED LIGHT INDICATOR 4 x 4
More informationAC5160 SiPass integrated controller kit
AC5160 SiPass integrated controller kit SiPass integrated Wall housing with pre-assembled basic SiPass integrated components Equipped with one ACC (AC5100), two dual reader interfaces (ADD5100) and one
More informationUC-2000 Installation Manual Unicorn Computers Technology Limited
UC2000 Installation Manual Copyright 2003. All rights reserved. Table of Contents Specifications 2 Enclosure for the UC2000 Controller 3 Unicorn Access Control System Configuration 4 UC2000 Controller
More informationKAUGJUHTIMISSÜSTEEMID TELECONTROL SYSTEMS MODEM TELEM-GSM/GPRS 3G. User manual
KAUGJUHTIMISSÜSTEEMID TELECONTROL SYSTEMS MODEM TELEM-GSM/GPRS 3G User manual Martem AS 2014 CONTENTS 1. Description...3 2. Features...3 3. Interfaces...3 4. Indication and switches...4 4.1 State LED indication...4
More informationMonitoring system CMC III
Monitoring system CMC III ENCOSURES POWER DISTRIBUTION CIMATE CONTRO INFRASTRUCTURE SOFTWARE & SERVICES W x H x D mm Temperature range Operating humidity range Sensors/CAN bus connection units Max. overall
More informationGrow your business by providing an intuitive home safety and comfort experience
Grow your business by providing an intuitive Self-contained, wireless security and interactive home automation system Fire detection s Video cameras Locks S.O.S./panic buttons Key features and benefits
More informationSETUP GUIDE INSTALLATION HANDBOOK. For Integrators, Installers and Administrators. Everything on how to get Kisi up and running. getkisi.
SETUP GUIDE INSTALLATION HANDBOOK For Integrators, Installers and Administrators Everything on how to get Kisi up and running getkisi.com 1 TABLE OF CONTENT 13 14 INSTALLING KISI AS A STAND-ALONE SYSTEM
More informationEntryphone. PinNet 4. Product manual. October 2010 R Granville Road, London SW18 5SD
Entryphone PinNet 4 Product manual October 2010 R4.9 www.entryphone.co.uk 23 Granville Road, London SW18 5SD This document covers the installation and use of the Entryphone on-line PinNet door control
More informationVT825 / Environmental Monitoring unit. Environmental Infrastructure monitoring
Environmental Infrastructure monitoring VT825 / Environmental Monitoring unit The unit is used for IT environmental control in data-centers, remote facilities, offices, industrial facilities & remote shelters.
More informationENVIROMUX Series Installation Instruction For:
ENVIROMUX Series Installation Instruction For: ENVIROMUX-IMD(-P) INFRARED MOTION SENSOR ENVIROMUX-IMD-CM(P) CEILING MOUNT MOTION SENSOR ENVIROMUX-IMD-TAA INFRARED MOTION SENSOR-TAA COMPLIANT ENVIROMUX-GBS(-P)
More information1. Introduction. 2. Product Overview Appearance Buttons/Mini USB Interface Description. UBI5000E User Manual
1. Introduction UBI5000E is a powerful GPS locator which is designed for vehicle, pets and assets tracking. With superior receiving sensitivity, fast TTFF and GSM frequencies 850/900/1800/1900. Its location
More informationIPassan Installation guide
IPassan Installation guide 1 Content 1 Overview... 3 1.1 Features... 3 1.2 Hardware... 3 1.2.1 s... 3 1.2.2 Extra modules... 5 1.3 IPassan manager... 7 2 Installation... 7 2.1... 8 2.1.1 Power supply...
More informationSMS TEXT DIALLER INSTALLATION AND OPERATION MANUAL
SMS TEXT DIALLER INSTALLATION AND OPERATION MANUAL Flashing Light (Text Message Received) Permanent Light (In Alarm) Optional Battery Backup SIM Card Carrier (see how to insert SMS card later in this manual)
More informationCardaxFT Reader I/O Interface
CardaxFT Reader I/O Interface CardaxFT Reader I/O Interface provides I/O functionality and an interface for connecting Cardax readers to the CardaxFT system. CardaxFT Reader I/O Interface provides an interface
More informationEZ-TAG2 Manual_Layout 5 11/12/ :14 Page 1 U S E R M A N UAL
EZ-TAG2 Manual_Layout 5 11/12/2012 09:14 Page 1 USER MANUAL EZ-TAG2 Manual_Layout 5 11/12/2012 09:14 Page 2 Contents EZ-TAG2 and Back Plate 1 x Security Torx Key 4 x Screws and raw plugs 1 x Marking out
More informationSee it. Control it. The TelPro Solution
See it. Control it. The TelPro Solution JANUARY 2017 Introducing the TelPro Solution A combined cellular and wireless IoT gateway and cloud portal system Collection and analysis of commercial and industrial
More informationIEI emerge MicroNode Install and Setup Guide. Contents
IEI emerge MicroNode Install and Setup Guide Contents Connecting power and the network to the MicroNode... 2 Using Power over Ethernet (PoE)... 3 or... 3 Using a 12 VDC power supply... 3 Connecting and
More informationConnecting a Cisco Input Module
CHAPTER 4 Overview The optional Cisco Input Module (Figure 4-1) is attached to a Cisco Physical Access Gateway or Cisco Reader Module to provide additional connections for up to ten input devices. Each
More informationWiring Guide. EP.NMiNi 2. Version 1.04 Last Updated:
Wiring Guide EP.NMiNi 2 Version 1.04 Last Updated: 31-01-2013 Before you begin Technical Support If you cannot find the answer to your question in this manual or in the Help files, we recommend you contact
More informationQUICK START GUIDE FOR ACCESS CONTROL BOARDS. DX Series One Door TCP/IP Web Server Controller. Model: ACP-DXEL1 to ExitPushAccessAccessBoard PWR-
QUICK START GUIDE FOR ACCESS CONTROL BOARDS DX Series One Door TCP/IP Web Server Controller Model: ACP-DXEL1 to ExitPushAccessAccessBoard PWR- Table of Contents 3 01- Introduction 4 02 - Overview 4 02.1
More informationIT monitoring. CMC III Monitoring system CMC III system representation CMC III system overview CMC III Processing Unit/Compact...
IT monitoring Monitoring system system representation...446 system overview...448 Processing Unit/Compact...450 sensors/accessories control units/ sensors...45 Interface for CMC II sensors...45 Access
More information1. Product Specification
1. Product Specification Item Specification Voltage 12VDC +10%, Current 1.2A Lock Relay 12VDC/2A Environmental Temperature working:0 ~45 ; storage:-10 ~55 Relative humidity working:40%~90%rh; Card Capacity
More informationAccess Easy Control System. Reference Guide
Access Easy Control System Reference Guide Content 3 1. AEC System Overview 4 2. AEC Main Components 6 3. AEC Configuration 7 4. AEC Benefits 8 5. AEC Easy Ordering 10 6. AEMC More than 16 readers? 12
More informationinstallation quick guide integrated access control & environmental monitoring
installation quick guide integrated access control & environmental monitoring Introduction This Installation Quick Guide is suitable for standard wallmountable AX300 controllers. Illustrative technical
More informationProfessional Access Control
Professional Access Control Product Reference Guide Stay connected with all that you love. The all-encompassing surveillance solution Combine access control & CCTV with VIP Vision Scaleable access control
More informationACCESS CONTROL SYSTEM
ACCESS CONTROL SYSTEM System versions Standalone controllers series based on integrated models KZ-400, 500, 600, 700, KZC-300,800, 900 KaDe Lite system based on integrated controllers KZ-1000 KaDe Premium
More informationIntrunet. SPC series Planning guide. Answers for infrastructure.
Intrunet SPC series Planning guide Answers for infrastructure. SPC series applications of future planning Small sized applications with stand-alone intrusion system connected to a Central Monitoring Station
More informationUnique access control box. Usage scenarios
2N Access Unit Unique access control box Usage scenarios Document: Příklady použití 2N Access Unit Page 1 of 8 Date of last revision: 2016-05-13 Content 1. Access Unit usage scenarios (premises entry only)...
More informationPRO3200 Professional Modular Access Control Hardware
PRO3200 Access Control Hardware As a part of the WIN-PAK software controlled hardware family the PRO3200 professional modular access control hardware is an advanced access control panel capable of providing
More informationSecured Series: Hub Plus Kit Single Door Controller Package Installation Manual
Secured Series: Hub Plus Kit Single Door Controller Package Installation Manual This package is designed to simplify the connections to our Secured Series Hub Plus Controller. This will translate into
More informationConnecting a Cisco Output Module
CHAPTER 5 Overview The optional Cisco Output Module (Figure 5-1) is attached to a Cisco Physical Access Gateway or Cisco Reader Module to provide additional connections for up to 8 outputs, each of which
More informationXR500/XR100 Command Processor Review. a) Zone expanders c) Output expanders b) All of these d) Single point detectors
Name Answer Key Company Address City, State, Zip Instructor Date Your email User Name = Password = XR500/XR100 Command Processor Review 1. may be connected to the LX-Bus. a) Zone expanders c) Output expanders
More informationIntelli-M eidc Quick Start Guide. infinias
Intelli-M eidc Quick Start Guide infinias Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus
More informationVT608 / Switched PDU with 8 outlets
Switched PDU with Monitoring VT608 / Switched PDU with 8 outlets Device is used for load management and allows to switch on/off or reboot up to 8 outlets. It has built-in temperature sensor, can connect
More informationL85 Integrated Locksets
DSX Access Systems, Inc. L85 Integrated Locksets The L85 software provides a method to integrate wired and wireless locksets into a DSX Access Control System. The L85 software leverages its Virtual Hardware
More informationIP68. Autarkic Data Loggers - MT-051 / MT-713 / MT-723
Autarkic Data Loggers - MT-051 / MT-713 / MT-723 Use in the most demanding environments These data loggers are designed for use in difficult to reach and widely distributed locations. In places where neither
More informationEP-ELVCTL Elevator Control (NION-16C48M)
EP-ELVCTL Elevator Control (NION-16C48M) Product Installation Document This document covers the procedures and specifications for installing the above listed unit and when appropriate, information regarding
More informatione-ask electronic Access Security Keyless-entry
e-ask electronic Access Security Keyless-entry CAN Multiplex System CAN Multiplex System Installation & Instructions (UM27 ~ 24324-03) Table of Contents Introduction... 1 e-pad Operation and Features...
More informationWaterCress Portfolio
WaterCress Portfolio The WaterCress Solution Option: X WaterCress Hardwired RS485 Comms Hard Wired Relay Outputs Sensor Minimum: 2 per card Maximum: 8 per card Radio Option: W WaterCress Wireless FM RS485
More information6222 Two Door Module Technical Operations Manual
6222 Two Door Module Technical Operations Manual TABLE OF CONTENTS Specifications...3 Overview...4 Operations...5 Custom Access Mode...5 Standard Access Mode...5 Offline Access Mode...5 Offline Memory...5
More informationModel HM-535 Power Supply Installation and Service Instructions
Model HM-535 Power Supply Installation and Service Instructions 430-535 0104 2004 Heritage MedCall, Inc SENTRY INSTALLATION & SERVICE INSTRUCTIONS POWER SUPPLY UNIT Model HM-535 IMPORTANT SAFETY INSTRUCTIONS
More informationACTPRO ACCESS CONTROL. Specification Guide
ACTPRO ACCESS CONTROL Specification Guide Table of Contents Glossary of Terms... 2 General System Specification Overview... 3 Hardware Requirements... 4 Four Door IP Controller... 4 Two Door IP Controller...
More informationOptional Remote Sensors - Connect via RJ12 Standard sensor lengths include 12 and 20. Custom lengths available upon request. Temperature:
RJ Port Sensors RJ Port Sensors Monitored Basic & Optional Remote Sensors - Connect via RJ12 Standard sensor lengths include 12 and 20. Custom lengths available upon request. Recommended Levels for Wiring
More informationSecure Connection with a Smart Device
Secure Connection with a Smart Device Providing your customers with Home Safety and Comfort Experience all @ the touch of a mobile device 2 Why choose ZeroWire? Supporting your customers every second of
More informationDECT-ULE Connected Home Peripherals
DECT-ULE Connected Home Peripherals Company Profile The Crow Group designs and manufactures since 1980 advanced security solutions for the worldwide security and the home automation markets. The Crow
More informationTechnical Manual Nova: Cabinet Security Management System (CSMS)
Technical Manual Nova: Cabinet Security Management System (CSMS) KP_nova_TM_160501_EN 1 Publication May, 2016, Keyprocessor BV Paasheuvelweg 20 1105BJ Amsterdam, The Netherlands www.keyprocessor.com/nova
More informationInnovative. Engineering. Power. structure source. Making the complex, simple. Structure Source PDU s
Structure Source PDU s Innovative Power Engineering High Quality Power Distribution for the Data Centre structure source Making the complex, simple structure source product range Rack and Server Power
More informationWiring Guide EP.NMINI. Version 1.02 Last Updated:
Wiring Guide EP.NMINI Version 1.02 Last Updated: 14-10-2014 1 Note: See http://www.entrypass.net/ for updates, revisions, and download the latest installation manual There are currently 2 version of EntryPass
More informationACT 5e prox Operating and Installation Instructions ACT Product Code: ACT 5e prox
standalone ACT 5e prox Operating and Installation Instructions ACT Product Code: ACT 5e prox ACT 5e prox 2R.indd 1 19/02/2016 17:05:06 ACTstandalone Robust and Reliable. 1 ACT 5e prox 2R.indd 2 19/02/2016
More informationInstallation Instructions CX254 Card Cage Power Injector
Installation Instructions CX254 Card Cage Injector Note: This installation should be made by a qualified service person and conform with local codes. CAUTION: To reduce the risk of electric shock do not
More informationLiebert. RDU-M Dynamic Environment Monitoring for Secure Data Center Infrastructure
Liebert RDU-M Dynamic Environment Monitoring for Secure Data Center Infrastructure Liebert RDU-M Manage critical equipment activity involving data center power and thermal management at multiple sites
More informationVT805 / Monitoring system
Environmental Infrastructure monitoring VT805 / Monitoring system Environmental monitoring of any facilities, control of security breaches, temperatures, smoke, water leakages, voltages and more. Compatible
More informationDKG-210 UNIVERSAL INTERNET GATEWAY UNIT
DKG-210 UNIVERSAL INTERNET GATEWAY UNIT AC & DC SUPPLY VERSIONS DESCRIPTION The DKG-210 is designed for internet monitoring and control of industrial devices using different protocols through the RAINBOW
More informationAC-115 Compact Networked Single-Door Controller Hardware Installation and Programming
AC-115 Compact Networked Single- Controller Hardware Installation and Programming Copyright 2013 by Rosslare. All rights reserved. This manual and the information contained herein are proprietary to REL,
More informationInstallation Instructions. i-net Access Control Units. Part Code: IA-PCB IA-ACB IA-ACU IA-KIT
Installation Instructions i-net Access Control Units Part Code: IA-PCB IA-ACB IA-ACU IA-KIT This device is configured for DHCP. Identity Access software will find this device, go to setup and controller,
More informationEZTAG3 PROXIMITY AND KEYPAD DOOR ENTRY
EZTAG PROXIMITY AND KEYPAD DOOR ENTRY USER MANUAL www.espuk.com EZTAG Manual_Layout.indd 8//06 5:8:0 System Components Proximity and Reader 0 x Proximity Tags x Hex Key x Plastic wall plug x Countersunk
More informationFinger Vein Access Control device Quick Start Guide Version: 1.0 Date: June USB slot. USB slot
Overview Fingerprint & Finger Vein Device Front Left Side: Finger Vein Device Touch screen Card reader Fingerprint reader Finger vein reader Finger vein sensor: During registration, after finger touches
More informationClymit 200. User Guide. External Threat Detector (ETD) Technology Corporation.
Clymit 200 External Threat Detector (ETD) User Guide Technology Corporation Rackit Technology Corporation 274 Madison Avenue, New York, NY 10016 Tel: (212) 679-0050 Fax: (212) 679-0040 1. 8 0 0. 6 3 6.
More informationPRO2200 Professional Modular Access Control Hardware
PRO2200 Access Control Hardware As a part of the WIN-PAK software controlled hardware family the PRO2200 professional modular access control hardware is an advanced access control panel capable of providing
More information2 Telecommunications Data Center Facility Requirements
Generic Requirements for Telecommunications Data Center Equipment and Spaces GR-3160-CORE Table of Contents Table of Contents Generic Requirements Notice of Disclaimer..................... iii Preface...........................................
More informationEL-ST100 KEYPAD CONTROLLER
WIRING DIAGRAM EL-ST100 KEYPAD CONTROLLER WEATHER-PROOF STANDALONE ACCESS CONTROLLER WITH KEYPAD & PROXIMITY TECHNOLOGY Programming and Installation Manual NOTE: www.elock2u.com ICT at work! Version 3.6
More informationTECHNICAL REFERENCE MANUAL FOR CAREL CONTROLLERS
TECHNICAL REFERENCE MANUAL FOR CONTROLLERS IOM-02 April 2017 Contents Page FUNCTIONAL LAYOUT... 1 pco5+ DESIGN... 2 SERIAL PORTS... 3 MOUNTING, DIMENSIONS & INSTALLATION... 4 Installation... 5 Environmental
More information2012 ACCESS CONTROL PROXIMITY KEYPAD FINGERPRINT BLUETOOH RADIO FREQUENCY COMBINED
01 ACCESS CONTROL PROXIMITY KEYPAD FINGERPRINT BLUETOOH RADIO FREQUENCY COMBINED INDEX QUICK GUIDE 0 STAND-ALONE 04 CENTRALIZED 36 ACCESSORIES 86 INDEX OF REFERENCES 94 QUICK GUIDE OF REFERENCES KEYPAD
More informationInnovative Electronics for a Changing World. Charge Smart R1 MPPT 12V/24V Auto detect Mains and Solar Battery charger with Remote Network Monitoring
Innovative Electronics for a Changing World Charge Smart R1 MPPT 12V/24V Auto detect Mains and Solar Battery charger with Remote Network Monitoring INDEX 1. SYSTEM DESCRIPTION 2. SYSTEM WIRING 3. SYSTEM
More informationROOM GUARD VT335. Environmental Infrastructure monitoring
Environmental Infrastructure monitoring ROOM GUARD VT335 Environmental monitoring of any facilities, control of security breaches, temperatures, smoke, water leakages, voltages and more. Compatible with
More informationOperation manual For NG BIOSINGLE Version 1.1
Operation manual For NG BIOSINGLE Version 1.1 SMART-I ELECTRONICS SYSTEMS PVT. LTD.(An ISO 9001:2008 certified company) R&D, Training & Customer Support Center: First Floor, Arihant Plaza Phase II, Village-Ovala,
More informationistar Pro Installation Guide
istar Pro Installation Guide UM-241 Version A1 October 2010 istar Pro Installation Quick Start Guide System Components The istar Pro hardware components consist of: General Controller Module (GCM) A general
More informationQuick Start Installation Guide
apc/l Quick Start Installation Guide Version A2 Document Part Number UM-201 May 2010 OVERVIEW The apc/l is an intelligent access control and alarm monitoring control panel which serves as a basic building
More informationEngineering and Manufacturing Excellence in Data Centre Infrastructure
Engineering and Manufacturing Excellence in Data Centre Infrastructure Since 1982 Australia s Largest PDU Manufacturer NetSense DCIM Software Intelligent Power PDU s SafetyNet Series 5 CREMS E-Rack 19
More information5-Port Industrial Ethernet Switch - DIN Rail Mountable
5-Port Industrial Ethernet Switch - DIN Rail Mountable Product ID: IES5102 This compact 5-port industrial Ethernet switch is engineered to deliver fast, reliable network connectivity and durability in
More informationDelivered the Way Yo u Want
SENSAPHONE IMS-4000 Infrastructure Monitoring System Mo nito r What Yo u Want Delivered the Way Yo u Want THE SENSAPHONE IMS-4000 MONITORS AND REPORTS THE INFORMATION THAT YOU NEED TO KNOW: Get critical
More informationx x 60 mm, 700 gm. Wall mounted enclosure, 1 Kg. Weatherproof, high impact GF ABS. Remote control and monitoring with debug features
Smart Hub Intelligent Energy Management and IoT Hub Unit (CT200i) General Dimension and weight 202.73 x 267.45 x 60 mm, 700 gm Dimension with standard cover 268 x 204 x 56 mm Dimension with weatherproof
More informationIndustrial 1-Port Gigabit 95W Ultra PoE Splitter
Industrial 1-Port Gigabit 95W Ultra Splitter Key Features Interface 2 RJ45 interfaces 1-port + input 1-port output 2 output (4-pin terminal block) 1 12V/24V DIP switch over Ethernet Complies with ultra
More informationSecure Connection with a Smart Device
Secure Connection with a Smart Device Providing your customers with Home Safety and Comfort Experience all @ the touch of a mobile device 2 Why choose ZeroWire? Supporting your customers every second of
More informationPQ-Box 100, 150, 200 & 300 Power Quality Analyser Clamps & Accessories
Mini Clamps: Part Number 111.7015 PQ-Box 100, 150, 200 & 300 Power Quality Analyser Clamps & Accessories Description 10 ma-to-20 A or 100 ma-to-200 A. Switchable range mini clamp. 40 Hz 20 khz 4 x mini
More informationBMCS CCX Cabinet. BMCS_CCX Cabinet is secured via a switchable 6A circuit breaker. Note the right selectivity ratio of your feeding.
Version: 2011-01-13 BMCS CCX Cabinet Description & Function: The BMCS_CCX Cabinet is a ready to install wall housing for one or more BMCS systems (see figures 1 to 3). The BMCS_CCX Cabinet is designed
More informationSingle Door Standalone Access Control User Manual
Single Door Standalone Access Control User Manual Reading this manual carefully before install and use the device 1. Packing List Name Quantity Remarks Keypad User manual Screw driver Rubber plug Self
More informationInstallation Instructions (KF-2000)
VERSION 2005. 10 Installation Instructions (KF-2000) Keico Hightech, Inc. Installation Instructions KF-2000 Keico Hightech Ace Twin Tower I 12 th FL 212-1, Guro-Dong, Guro-Gu Phone +82-2-853-9000 Fax +82-2-830-7809
More informationEA500. Installation Instructions Transponder
EA500 EN Installation Instructions Transponder EA500 Installation Instructions 1.0 Overview EN 2 1.0 Overview The EA500 Transponder is the Security Escort module that provides communications between the
More informationImproX IXP20 Controller INSTALLATION MANUAL
MODEL NUMBER: ISC920-0-0-GB-XX ISC921-5-0-GB-XX IXP20 CONTROLLER SPECIFICATIONS Working Environment Plastic Housing... Power ImproX IXP20 Controller INSTALLATION MANUAL Designed to work in an indoor (dry)
More informationMDVR 800 QUICK START GUIDE
MDVR 800 QUICK START GUIDE Introduction & Warnings Before installing please read the following warnings carefully. Stortech CCTV strongly recommends that all connections and installations are carried out
More informationEnvironmental monitoring of any facilities, control of security breaches, temperatures, smoke, water leakages, voltages and more.
VT800 Environmental monitoring of any facilities, control of security breaches, temperatures, smoke, water leakages, voltages and more. Compatible with all VT or SC sensors, it provides a complete environmental,
More informationLock Driver 8 Technical Manual
Table of contents... 3 Product description... 3 Connections... 4 Connecting Electronic Locks... 5 DIP switch settings... 6 Maintenance... 8 Troubleshooting Guide... 8 Technical data... 8 Appendix... 8
More informationIndustrial IEEE 802.3at Gigabit High Power over Ethernet Splitter
Industrial IEEE 802.3at Gigabit High over Ethernet Splitter Interface 2-port RJ-45 interfaces 1-port + input 1-port output 2 out (4-pin Terminal Block) over Ethernet Splitter Complies with IEEE 802.3at
More informationController Cardax FT Controller The CardaxFT Controller 5000 is the intelligent field controller in the CardaxFT security system.
The features described in this data sheet are being progressively added to the CardaxFT Controller (5000 Series) during 2002/2003. Please contact Cardax for further information. Cardax FT Controller 5000
More informationIntrusion Control Panels Quick Guide. May 2015
Intrusion Control Panels Quick Guide May 2015 Control Panels B Series Commercial Type Number B3512 B4512 B5512 Applications Type Residential, Small Commercial Residential, Small Commercial Residential,
More informationControl Panel Solutions
HONEYWELL ACCESS SYSTEMS Control Panel Solutions Honeywell s control panel solutions have been the reliable choice of dealers for many years. Our controllers are the benchmark of the industry and offer
More informationINTELLIKEY. Mini-DCU Installation Manual GENIUS AT YOUR FINGERTIPS. 1 rev
R INTELLIKEY GENIUS AT YOUR FINGERTIPS MiniDCU Installation Manual 1 rev082803 rev082803 2 Contents Introduction... 4 EZ123 Software Programming... 4 Quantum Software Programming... 6 Suggested Wiring
More informationTechnical System Catalogue CMC III Monitoring System
Technical System Catalogue CMC III Monitoring System CMC III monitoring system CMC III Processing Unit 3 6 1 5 7 4 8 9 10 11 Computer Multi Control (CMC) is an alarm system for network and server enclosures,
More informationISC GB-XX ISC GB-XX ISC GB-XX ISC GB-XX
ISC910-1-0-GB-XX ISC911-5-0-GB-XX ISC920-0-0-GB-XX ISC921-5-0-GB-XX The ImproX IXP20 is a fully featured, stand-alone Access Control System supporting up to 1 000 Tagholders and 5 000 transactions. Designed
More information2 IDS LCD Keypad User Manual C Issued March 2009
2 3 4 Contents 1. Introduction to the IDS LCD Digital Keypad...8 2. Arming the Control Panel...8 2.1 Away Arming...8 2.1.1 How to Away Arm...8 2.1.2 Quick Away Arm Shortcut Key...8 2.2 Stay Arming...9
More informationROOM GUARD VT335. Environmental Infrastructure monitoring
Environmental Infrastructure monitoring ROOM GUARD VT335 Environmental monitoring of any facilities, control of security breaches, temperatures, smoke, water leakages, voltages and more. Compatible with
More information