Photometric Test Report

Transcription

1 Photometric Test Report Relevant Standards RIES LM RANSI C82.77:2014 Prepared For RAB Lighting Inc. Room 6A33, No.1388, Wuzhong road,shanghai,china Xiao Prepared By Deliver Co., Ltd. Block 11, 78 Keling Road, SSTP, Suzhou, China Project Number DLF Report Number DLF a Test Date 2018/5/9 Issue Date 2018/5/9 Prepared By Approved By Wangzun Zhu Kevin Jia The results contained in this report pertain only to the tested sample. This report shall not be reproduced, except in full, without written approval of Deliver Co.,Ltd. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP. Version:1.0 Page 1 of 16

2 1.0 Test Summary DLC Technical Requirements v4.3 Outdoor - Architectural Flood and Spot Luminaires Requirement Category Test Method Requirements Test value Results (Fail/Pass) Lamp Output (lm) Zonal Lumen Requirement (0-90 ) Minimum Luminaire Efficacy (lm/w) Alowable CCTs* (K) Minimum CRI Power Factor IES LM IES LM IES LM IES LM IES LM CIE ANSI C82.77: P 85% % P P P P P Total Harmonic Distortion (A%) ANSI C82.77: % 7.61% P 2.0 Test List Test Item Test Test Date Model Number Sample No. 1 Integrating Sphere Test 2018/5/9 FXLED200SFY E1 2 Goniophotometer Test 2018/5/9 FXLED200SFY E1 3 THD and PF Test 2018/5/9 FXLED200SFY E1 Remark(If any) 1 This report shall not be used by the client to claim product endorsement by NVLAP, NIST or any agency of the US government. 2 The results reported herein have been performed in accordance with the laboratory s terms of accreditation. This report shall not be reproduced except in full without the written approval of the Laboratory. The results in this report apply to the test sample(s) mentioned above at the time of the testing period only and are not to be used to indicate applicability to other similar products. This report does not imply that the product(s) has met the criteria for certification. Version:1.0 Page 2 of 16

3 3.0 Production Description Luminaire Description: LUMCAT: FXLED200SFY LUMINAIRE: CAST FINNED METAL HOUSING, CAST DIFFUSE CIRCUIT BOARD MOUNTING PLATE, 8 CIRCUIT BOARDS EACH WITH 1 LED, MOLDED SPECULAR FINISHED PLASTIC REFLECTOR WITH 1 APERTURE AND 1 CLEAR PLASTIC CONVEX INNER LENS WITH 3 INTEGRAL MOUNTING POSTS PER LED, CLEAR GLASS LENS IN CAST BROWN PAINTED METAL LENS FRAME WITH VISOR. LAMP: EIGHT WHITE MULTI-CHIP LIGHT EMITTING DIODES (LEDS), AIMED AT THE HORIZON. Electrical Specification: 120V-277V,50/60HZ Light source: LC040D_Gen2 Manufacturer Of Light Source: Samsung Electronics LED Business Photos of Luminaire Characteristics Version:1.0 Page 3 of 16

4 4.0 LM-79 Measurement and Test Results 4.1 Integrating Sphere Test Model No. FXLED200SFY Sample ID. E1 Opreate time (Min.) 90 Stabilization time (Min.) 45 Test Method The samples were tested according to the IES LM Photometric paramters were measured using an integrating sphere, a spectroradiometer and software. The ambient temperature condition inside the sphere was maintained at 25ºC ± 1ºC. The sample measurements were made using a spectroradiometer connected by a fiber optic cable and detector through the detector port of the integrating sphere. The voltage of an AC power supply (RMS voltage) or DC power supply (instantaneous voltage) applied to the device under test shall be regulated to within ±0.2 percent under load. The sample was measured using 4π geometry and operated at rated voltage and was stabilized before measurement. Chromaticity coordinates, correlated color temperature and color rendering index were calculated from the spectral radiant flux measurements taken at 1 nm intervals over the range of 380 to 780 nm. Temperatur e ( C) Voltage (Vac) Test Conditions Frequency Current (A) Power (W) Power Factor (Hz) CCT (K) CRI (Ra) Duv E-04 Test Result Version:1.0 Page 4 of 16

5 4.1 Integrating Sphere Test Spectroradiometric Parameters Version:1.0 Page 5 of 16

6 4.0 LM-79 Measurement and Test Results 4.3 Goniophotometer Test Model No. FXLED200SFY Sample ID. E1 Opreate time (Min.) 90 Stabilization time (Min.) 45 Test Method The samples were tested according to the IES LM Photometric paramters were measured using a type C goniophotometer and software. The ambient temperature shall be maintained at 25 C ± 1 C, measured at a point not more than 1 m from the sample and at the same height as the sample. The voltage of an AC power supply (RMS voltage)or DC power supply (instantaneous voltage) applied to the device under test shall be regulated to within ±0.2 percent under load. The samples were operated at rated voltage and was stabilized before measurement. Luminous flux, luminaire efficacy, zonal lumen were calculated from the software taken at 0.5 o vertical intervals and 10 o horizontal intervals. Temperature ( C) Voltage (Vac) Test Conditions Frequency Current (A) (Hz) Power (W) Power Factor Orientation Light Down Flux(lm) Zonal Lumen Requiremen t(0-90 ) Horizontal Spread Test Result Field Angle(10%) Beam Angle(50%) Luminous Efficacy (lm/w) Vertical Spread Horizontal Spread Vertical Spread % Version:1.0 Page 6 of 16

7 4.3 Goniophotometer Test Light Distrubtion Curve Isolux Plot Version:1.0 Page 7 of 16

8 4.3 Goniophotometer Test Zonal Lumen Summary Version:1.0 Page 8 of 16

9 4.3 Goniophotometer Test ZONAL LUMEN SUMMARY Zonal (lm) Total (lm) Percent % % % % % % % % % % % % % % % % % % Version:1.0 Page 9 of 16

10 4.3 Goniophotometer Test Axial Candela DEG. HOR. DEG. VERT Version:1.0 Page 10 of 16

11 4.3 Goniophotometer Test Characteristics NEMA Type 7 H x 6 V Maximum Candela Maximum Candela Angle -3 H 17 V Horizontal Beam Angle (50%) 90.4 Vertical Beam Angle (50%) 71.5 Horizontal Field Angle (10%) Vertical Field Angle (10%) Lumens Per Lamp N.A. (absolute) Total Lamp Lumens N.A. (absolute) Beam Lumens Beam Efficiency N.A. Field Lumens Field Efficiency N.A. Spill Lumens 1124 Luminaire Lumens Total Efficiency N.A. Total Luminaire Watts Ballast Factor 1 ISOCANDELA CURVES Version:1.0 Page 11 of 16

12 Axial Candela * Version:1.0 Page 12 of 16

13 LUMEN TABULATION Total * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * 9.77 * 9.56 * 9.34 * * * * * * * * 9.75 * 9.20 * 5.79 * Version:1.0 Page 13 of 16

14 5.27 * * * * * 9.93 * 9.71 * 9.49 * 9.28 * * * * * * * * 9.69 * 9.14 * 5.76 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * 6.29 * 6.47 * 6.55 * 6.57 * Total ### 960 ### ### ### Version:1.0 Page 14 of 16

15 5.0 THD and PF Test Model No. FXLED200SFY Sample ID. E1 Test Method The samples were tested according to the ANSI C82.77:2002. The total harmonic distortion shall be measured to the 40th order. The ambient temperature condition was maintained at 25ºC ± 1ºC. The sample measurements were made using a digital power meter and power supply. The sample was operated at rated voltage and was stabilized before measurement. The total harmonic distortion were calculated. Temperature ( C) Voltage (Vac) Frequency (Hz) Test Results Current (A) Power (W) Power Factor THD % % Version:1.0 Page 15 of 16

16 6.0 Equipment Information Test Equipment Equipment ID Equipment Name Last Calibration Due DLF107 Integrating Sphere System 2017/12/28 Calibration 2018/12/27 Date DLF108 Auxiliary Lamp Measurement Standard Lamp DLF122 Standard Lamp Type: 220 V, A, Tungsten, Omni-derectional DLF116 AC Power Source DLF113 Power Meter DLF112 Temperature Recorder DLF114 Temperature & Humidity Datalogger DLF101 Goniophotometer Standard Lamp DLF125 Standard Lamp Type: V, A, Tungsten, Omni-derectional DLF104 AC Power Source DLF507 DC Power Source DLF102 Power Meter DLF111 Temperature & Humidity Datalogger DLF119 Power Meter DLF031 Temperature data logger DLF022 Digital power meter DLF003 Temperature & Humidity Datalogger *************** End of Test Report****************** Version:1.0 Page 16 of 16