VP4001. RS-232C Control Specification

Transcription

1 RS-232C Control Specification : Rev 00 VP4001 RS-232C Control Specification Categy : Video Project Document Version : 1.0 Auth(s) : Marantz America, Inc. Date : 2006/10/07 Number of Page : 15 Marantz America, Inc All rights are reserved. Reproduction in whole in part is prohibited without the written consent of copyright. All specifications might be subject to change without notice.

2 VP4001 RS-232C Control Specification Page: 2 / 15 Table of Contents 1. Introduction Purpose Scope Abbreviations Global Description Overview Block Diagram Interface connection specification of the product RS-232C Cross Cable Signal Discription Detailed Description Connection fmat Physical connection Transmission data fmat Transmission data fmat from Host to Slave Fm1: Transmission data fmat from Slave to Host Fm1: OK/ Fm2: Status answer and Auto status feedback The transaction sequences and the regulations The transaction sequences The transaction regulations Definitions of and Status s Nmal f General Nmal f COMPONENT 1 Input Nmal f COMPONENT 2 Input Nmal f S-VIDEO Input Nmal f VIDEO Input Nmal f RGB Input Nmal f HDMI Input Revision histy...15

3 VP4001 RS-232C Control Specification Page: 3 / Introduction 1-1. Purpose This document was written as a reference specification of products that are controled by the host controller Scope This document would be using by software hardware engineers f production of the product Abbreviations Abbreviation Description 2. Global Description 2-1. Overview A Host controller can control watch out the product as a Slave very easily via the communication cable Block Diagram HOST (Controller) RS232C cable (Cross) SLAVE (VP4001) Connect: Mini DIN 9-pin * The product connect is using 9-pin Mini DIN connect. * D-SUB to Mini DIN adapter is attached as an accesy. * Cross type RS232C cable have to be used (D-SUB 9-pin female on product side) Interface connection specification of the product RS-232C Cross Cable Connect Pin # Signal Name Connection Signal Name Pin # 1 CD CD 1 2 RD RD 2 3 SD SD 3 4 ER ER 4 5 SG SG 5 6 DR DR 6 7 RS RS 7 8 CS CS 8 9 CI CI 9 Connect <Adapter connect> D-SUB 9-pin, Male

4 VP4001 RS-232C Control Specification Page: 4 / Signal Discription Pin # Signal Name I/O Reference 1 CD Not Connected 2 RD Receive Data Input Connected to Internal Circuit 3 SD Send Data Output Connected to Internal Circuit 4 ER 5 SG Signal Dround Connected to Internal Circuit 6 DR 7 RS Request to Send Connected to Internal Circuit 8 CS Clear to Send Connected to Internal Circuit 9 CI Detailed Description The interface specification between the product and a Host controller is described below Connection fmat Physical connection Baud Rate : 9600bps pbs Data Bits : 8bit Parity : None Stop bit : 1bit Handshaking : None 3-2. Transmission data fmat Transmission data fmat from Host to Slave There are two kinds of transmission data fm from Host shown below Fm1: is a data that requests some status change. s from the Host are sent in the following der: command, parameter, and return code. After the project processes the command from the host, it sends a response code to the computer. Fmat 0DH (4 digits) (4 digits Return Start character : None COMMAND : see list End character (CR) : 0Dh Note: When controlling the project by using RS-232C commands, wait f at least 30 seconds after the power has been turned on, and then transmit the commands. When me than one code is being sent, send each command only after the response code f the previous command from the project is verified.

5 VP4001 RS-232C Control Specification Page: 5 / Transmission data fmat from Slave to Host There are two kinds of transmission data fm from Slave shown below Fm1: OK/ OK is a reply data from Slave when Slave got an acceptable command data from Host. Fmat O K 0DH Return Reply: OK End character (CR): 0Dh is a reply data from Slave when Slave got an increct data, Status request data some other data from Host. Fmat E R R 0DH Return Reply: NAK End character (CR): 0Dh Fm2: Status answer and Auto status feedback Status answers are reply data when Slave got an acceptable Request status data from Host. Auto status feedbacks are send to Host data when a Slave s status is changed. Start character : None Answer character : see Status list End character (CR) : 0Dh 3-3. The transaction sequences and the regulations The transaction sequences There are three kinds of the transaction sequence, *A transaction starts from from Host and then Slave will return Status answer, OK. *A transaction starts from Status request from Host and then Slave will return Status answer. *A transaction starts by Auto status feedback from Slave when a Slave s status was changed The transaction regulations The transactions have some kinds of regulation. * An reply (OK, Status answer) transmittion by Slave has to finish 500ms when got a a Status request from Host. * Host must not transmit an another Status request until "it receives a answer by a previous Status request" "it passes a term of waitinng time from a finishing of previous transmission of a a Status request ". * Slave has to finish a transaction under 500ms when it sends Auto status feedback data.

6 VP4001 RS-232C Control Specification Page: 6 / Definitions of and Status This section explains how to define and Status s This chapter will show the commands of this product. POWER INPUT OSD BACKGROUND COLOR AUTO POWER OFF OSD LANGUAGE V-KEYSTONE H-KEYSTONE Nmal f General "_" is Space "*" is value "POWER ON" "STANDB Y" "40sec. Power on" POWER ON P O W R _ 1 OK POWER OFF P O W R _ 0 OK OK COMP.1 I V E D _ 1 COMP.2 I V E D _ 2 S-VIDEO I V E D _ 3 VIDEO I V E D _ 4 RGB I R G B _ 1 HDMI I R G B _ 2 OSD_DISPLAY : ON I M D I _ 1 OSD_DISPLAY : OFF I M D I _ 0 BACKGROUND : BLUE I M B G _ 1 BACKGROUND : NONE I M B G _ 2 Auto Power Off: NO USE A P O W _ 0 Auto Power Off : USE A P O W _ 1 LANGUAGE : English M E L A _ 1 LANGUAGE : Deutsch M E L A _ 2 LANGUAGE : Español M E L A _ 3 LANGUAGE : Nederlands M E L A _ 4 LANGUAGE : Français M E L A _ 5 LANGUAGE : Italiano M E L A _ 6 LANGUAGE : Svenska M E L A _ 7 LANGUAGE : 日本語 (Japanese) M E L A _ 8 LANGUAGE : Ptuguês M E L A _ 9 LANGUAGE : 汉语 (Chinese) LANGUAGE : 한국어 (Kean) Keystone Vertical value ( ) Keystone Hizontal value ( ) M E L A 1 0 M E L A 1 1 OK OK OK OK OK K E Y V _ * * * OK K E Y H _ * * * OK The Max. adjustable value : difined by the combination of both H/V adjustment. The Max. adjustable value : difined by the combination of both H/V adjustment.

7 VP4001 RS-232C Control Specification Page: 7 / 15 IMAGE SHIFT FREEZE AUTO SYNC. MANUAL AUTO SYNC. Reset SYNC. ADJUSTMENT LAMP IRIS Position SIGNAL CLOCK SIGNAL PHASE HORIZONTAL POSITION VERTICAL POSITION Set the OVERSCAN the SUBTITLE VIDEO SYSTEM Image Shift value ( ) "_" is Space "*" is value "POWER ON" L N D S _ * * * OK Freeze: OFF F R E Z _ 0 Freeze: ON F R E Z _ 1 Auto Sync OFF A A D J _ 0 Auto Sync ON A A D J _ 1 OK OK "STANDB Y" "40sec. Power on" Auto Sync. Adj. Start A D J S _ 1 OK This is effective in RGB. Reset Sync. Adj. I A R E _ 1 OK Eco : ON T H M D _ 1 Eco : OFF T H M D _ 0 Iris: WIDE I R I S _ 1 Iris: MEDIUM I R I S _ 2 Iris: NARROW I R I S _ 3 OK OK Clock value ( ) I N C L * * * * OK This is effective in RGB. Phase value ( ) I N P H _ * * * OK This is effective in RGB. H-Position value (-150 to +150) V- position value (-60 to +60) Overscan H value ( ) Overscan V value ( ) I A H P * * * * OK I A V P _ * * * OK O V S H _ * * * O V S V _ * * * OK Subtittle value ( ) S T S Z _ * * * OK Video System: AUTO M E S Y _ 1 Video System: PAL M E S Y _ 2 Video System: SECAM M E S Y _ 3 Video System: NTSC4.43 M E S Y _ 4 Video System: NTSC3.58 M E S Y _ 5 Video System: PAL-N M E S Y _ 6 Video System: PAL-M M E S Y _ 7 Video System: PAL-60 M E S Y _ 8 INSTALLATION Reverse: OFF (Front) I M R E _ 0 (Reverse) Reverse: ON (Rear) I M R E _ 1 INSTALLATION Inverse: OFF (Table Top) I M I N _ 0 (Inverse) Inverse: ON (Ceiling) I M I N _ 1 OK OK OK This is effective in COMP.1/2 and VIDEO. This is effective in COMP.1/2 and VIDEO. This is effective in S-VIDEO and VIDEO.

8 VP4001 RS-232C Control Specification Page: 8 / 15 SPECIAL DISPLAY *1 Check LAMP STATUS Check PROJECTOR STATUS Check CURRENT INPUT Check LAMP STATUS Check LAMP TIME Check LAMP LIFE Check MODEL NAME "_" is Space "*" is value Special :1 S P M D _ 1 Special :2 S P M D _ 2 Special :3 S P M D _ 3 Special :4 S P M D _ 4 Special :5 S P M D _ 5 Lamp Status Check T L P S _ 1 Abnmal Status Check T A B N _ 1 Input Check I C H K???? Power Status Check T P O W _ 1 Lamp Elapsed Time Display T L T T _ 1 Lamp Life (%) Display T L T L _ 1 "POWER ON" OK 0:OFF 1:ON 2:Re-try 3:Waiting 4:Lamp Err 0:Nmal, 1:High Temp., 8: Lamp life: less than 5%, 16: Lamp broken, 32: Failure of turning on the lamp 1:COMP.1 2:COMP.2 3:S-VIDEO 4:VIDEO 5:RGB 6:HDMI 1:ON, 2: Under Cooling 3: Under shutdown 0~9999 (Integer) 0%~ 100% (Integer) "STANDB Y" "40sec. Power on" 0:OFF 4:Lamp Err 0: Nmal 1: High Temp. 2: Cooling Fan Err 4: Open the lamp cover 8: Lamp Life: less than 5% 16: Lamp broken 32: Failure of turning on the lamp 64: Abnmal high temp. 0: Standby 0~9999 (Integer) 0%~ 100% (Integer) l Name Check M N R D _ 1 VP4001 VP4001 RESET ALL All Reset A L R E _ 1 OK Read Only

9 VP4001 RS-232C Control Specification Page: 9 / 15 PICTURE CONTRAST BRIGHTNESS Nmal f COMPONENT 1 Input _ is Space * is value Picture mode: Standard V A P S _ 1 Picture mode: Natural V A P S _ 2 Picture mode: Dynamic V A P S _ 3 Picture mode: Theater1 V A P S _ 4 Picture mode: Theater2 V A P S _ 5 Picture mode: Memy V A P S _ 0 POWER ON OK STANDB Y 40sec. Power on Contrast value ( ) V A P I _ * * * OK Brightness value( ) V A B R _ * * * OK COLOR Col value( ) V A C O _ * * * OK TINT Tint value( ) V A T I _ * * * OK SHARPNESS Sharpness value( ) V A S H _ * * * OK RED Red value( ) V A R D _ * * * OK BLUE Blue value( ) V A B E _ * * * OK COLOR TEMP. BRILLIANT COLOR Reset PICTURE SETTING ASPECT DNR Position PROGRESSIVE Col Temp.: 5500K V A C T _ Col Temp.: 6500K V A C T _ Col Temp.: 7500K V A C T _ Col Temp.: 8500K V A C T _ Col Temp.: 9300K V A C T _ Col Temp.: 10500K V A C T _ Brilliant Col: 0 V A W E _ 0 Brilliant Col: 1 V A W E _ 1 Brilliant Col: 2 V A W E _ 2 OK OK Picture reset V A R E _ 1 OK Aspect: FULL R A S V _ 2 Aspect: NORMAL R A S V _ 7 Aspect: ZOOM R A S V _ 1 3D DNR : OFF V A N R _ 0 3D DNR : Level1 V A N R _ 1 3D DNR : Level2 V A N R _ 2 3D DNR : Level3 V A N R _ 3 IP Conversion: 2D V A I P _ 0 IP Conversion: 3D V A I P _ 1 IP Conversion: Film V A I P _ 2 OK OK OK

10 VP4001 RS-232C Control Specification Page: 10 / 15 PICTURE CONTRAST BRIGHTNESS Nmal f COMPONENT 2 Input _ is Space * is value Picture mode: Standard V B P S _ 1 Picture mode: Natural V B P S _ 2 Picture mode: Dynamic V B P S _ 3 Picture mode: Theater1 V B P S _ 4 Picture mode: Theater2 V B P S _ 5 Picture mode: Memy V B P S _ 0 POWER ON OK STANDB Y 40sec. Power on Contrast value ( ) V B P I _ * * * OK Brightness value( ) V B B R _ * * * OK COLOR Col value( ) V B C O _ * * * OK TINT Tint value( ) V B T I _ * * * OK SHARPNESS Sharpness value( ) V B S H _ * * * OK RED Red value( ) V B R D _ * * * OK BLUE Blue value( ) V B B E _ * * * OK COLOR TEMP. BRILLIANT COLOR Reset PICTURE SETTING ASPECT DNR Position PROGRESSIVE Col Temp.: 5500K V B C T _ Col Temp.: 6500K V B C T _ Col Temp.: 7500K V B C T _ Col Temp.: 8500K V B C T _ Col Temp.: 9300K V B C T _ Col Temp.: 10500K V B C T _ Brilliant Col: 0 V B W E _ 0 Brilliant Col: 1 V B W E _ 1 Brilliant Col: 2 V B W E _ 2 OK OK Picture reset V B R E _ 1 OK Aspect: FULL R B S V _ 2 Aspect: NORMAL R B S V _ 7 Aspect: ZOOM R B S V _ 1 3D DNR : OFF V B N R _ 0 3D DNR : Level1 V B N R _ 1 3D DNR : Level2 V B N R _ 2 3D DNR : Level3 V B N R _ 3 IP Conversion: 2D V B I P _ 0 IP Conversion: 3D V B I P _ 1 IP Conversion: Film V B I P _ 2 OK OK OK

11 VP4001 RS-232C Control Specification Page: 11 / 15 PICTURE CONTRAST BRIGHTNESS Nmal f S-VIDEO Input _ is Space * is value Picture mode: Standard V C P S _ 1 Picture mode: Natural V C P S _ 2 Picture mode: Dynamic V C P S _ 3 Picture mode: Theater1 V C P S _ 4 Picture mode: Theater2 V C P S _ 5 Picture mode: Memy V C P S _ 0 POWER ON OK STANDB Y 40sec. Power on Contrast value ( ) V C P I _ * * * OK Brightness value( ) V C B R _ * * * OK COLOR Col value( ) V C C O _ * * * OK TINT Tint value( ) V C T I _ * * * OK SHARPNESS Sharpness value( ) V C S H _ * * * OK RED Red value( ) V C R D _ * * * OK BLUE Blue value( ) V C B E _ * * * OK COLOR TEMP. BRILLIANT COLOR Reset PICTURE SETTING ASPECT DNR Position PROGRESSIVE Col Temp.: 5500K V C C T _ Col Temp.: 6500K V C C T _ Col Temp.: 7500K V C C T _ Col Temp.: 8500K V C C T _ Col Temp.: 9300K V C C T _ Col Temp.: 10500K V C C T _ Brilliant Col: 0 V C W E _ 0 Brilliant Col: 1 V C W E _ 1 Brilliant Col: 2 V C W E _ 2 OK OK Picture reset V C R E _ 1 OK Aspect: FULL R C S V _ 2 Aspect: NORMAL R C S V _ 7 Aspect: ZOOM R C S V _ 1 3D DNR : OFF V C N R _ 0 3D DNR : Level1 V C N R _ 1 3D DNR : Level2 V C N R _ 2 3D DNR : Level3 V C N R _ 3 IP Conversion: 2D V C I P _ 0 IP Conversion: 3D V C I P _ 1 IP Conversion: Film V C I P _ 2 OK OK OK

12 VP4001 RS-232C Control Specification Page: 12 / 15 PICTURE CONTRAST BRIGHTNESS Nmal f VIDEO Input _ is Space * is value Picture mode: Standard V D P S _ 1 Picture mode: Natural V D P S _ 2 Picture mode: Dynamic V D P S _ 3 Picture mode: Theater1 V D P S _ 4 Picture mode: Theater2 V D P S _ 5 Picture mode: Memy V D P S _ 0 POWER ON OK STANDB Y 40sec. Power on Contrast value ( ) V D P I _ * * * OK Brightness value( ) V D B R _ * * * OK COLOR Col value( ) V D C O _ * * * OK TINT Tint value( ) V D T I _ * * * OK SHARPNESS Sharpness value( ) V D S H _ * * * OK RED Red value( ) V D R D _ * * * OK BLUE Blue value( ) V D B E _ * * * OK COLOR TEMP. BRILLIANT COLOR Reset PICTURE SETTING ASPECT DNR Position PROGRESSIVE Col Temp.: 5500K V D C T _ Col Temp.: 6500K V D C T _ Col Temp.: 7500K V D C T _ Col Temp.: 8500K V D C T _ Col Temp.: 9300K V D C T _ Col Temp.: 10500K V D C T _ Brilliant Col: 0 V D W E _ 0 Brilliant Col: 1 V D W E _ 1 Brilliant Col: 2 V D W E _ 2 OK OK Picture reset V D R E _ 1 OK Aspect: FULL R D S V _ 2 Aspect: NORMAL R D S V _ 7 Aspect: ZOOM R D S V _ 1 3D DNR : OFF V D N R _ 0 3D DNR : Level1 V D N R _ 1 3D DNR : Level2 V D N R _ 2 3D DNR : Level3 V D N R _ 3 IP Conversion: 2D V D I P _ 0 IP Conversion: 3D V D I P _ 1 IP Conversion: Film V D I P _ 2 OK OK OK

13 VP4001 RS-232C Control Specification Page: 13 / 15 PICTURE CONTRAST BRIGHTNESS Nmal f RGB Input _ is Space * is value Picture mode: Standard R A P S _ 1 Picture mode: Natural R A P S _ 2 Picture mode: Dynamic R A P S _ 3 Picture mode: Theater1 R A P S _ 4 Picture mode: Theater2 R A P S _ 5 Picture mode: Memy R A P S _ 0 POWER ON OK STANDB Y 40sec. Power on Contrast value ( ) R A P I _ * * * OK Brightness value( ) R A B R _ * * * OK COLOR Col value( ) R A C O _ * * * OK TINT Tint value( ) R A T I _ * * * OK SHARPNESS Sharpness value( ) R A S H _ * * * OK RED Red value( ) R A R D _ * * * OK BLUE Blue value( ) R A B E _ * * * OK COLOR TEMP. BRILLIANT COLOR Reset PICTURE SETTING ASPECT DNR Position PROGRESSIVE SIGNAL TYPE Col Temp.: 5500K R A C T _ Col Temp.: 6500K R A C T _ Col Temp.: 7500K R A C T _ Col Temp.: 8500K R A C T _ Col Temp.: 9300K R A C T _ Col Temp.: 10500K R A C T _ Brilliant Col: 0 R A W E _ 0 Brilliant Col: 1 R A W E _ 1 Brilliant Col: 2 R A W E _ 2 OK OK Picture reset R A R E _ 1 OK Aspect: FULL R A S R _ 2 Aspect: NORMAL R A S R _ 7 Aspect: ZOOM R A S R _ 1 Aspect: THROUGH R A S R _ 3 3D DNR : OFF R A N R _ 0 3D DNR : Level1 R A N R _ 1 3D DNR : Level2 R A N R _ 2 3D DNR : Level3 R A N R _ 3 IP Conversion: 2D R A I P _ 0 IP Conversion: 3D R A I P _ 1 IP Conversion: Film R A I P _ 2 Input Signal: Auto I A S I _ 0 Input Signal: RGB I A S I _ 1 Input Signal: Component I A S I _ 2 OK OK OK OK Common setting f RGB&HDMI input

14 VP4001 RS-232C Control Specification Page: 14 / 15 PICTURE CONTRAST BRIGHTNESS Nmal f HDMI Input Picture mode: Standard R B P S _ 1 Picture mode: Natural R B P S _ 2 Picture mode: Dynamic R B P S _ 3 Picture mode: Theater1 R B P S _ 4 Picture mode: Theater2 R B P S _ 5 Picture mode: Memy R B P S _ 0 OK Contrast value ( ) R B P I _ * * * OK Brightness value( ) R B B R _ * * * OK COLOR Col value( ) R B C O _ * * * OK TINT Tint value( ) R B T I _ * * * OK SHARPNESS Sharpness value( ) R B S H _ * * * OK RED Red value( ) R B R D _ * * * OK BLUE Blue value( ) R B B E _ * * * OK COLOR TEMP. BRILLIANT COLOR Reset PICTURE SETTING ASPECT DNR Position PROGRESSIVE SIGNAL TYPE HDMI Setting Col Temp.: 5500K R B C T _ Col Temp.: 6500K R B C T _ Col Temp.: 7500K R B C T _ Col Temp.: 8500K R B C T _ Col Temp.: 9300K R B C T _ Col Temp.: 10500K R B C T _ Brilliant Col: 0 R B W E _ 0 Brilliant Col: 1 R B W E _ 1 Brilliant Col: 2 R B W E _ 2 OK OK Picture reset R B R E _ 1 OK Aspect: FULL R B S R _ 2 Aspect: NORMAL R B S R _ 7 Aspect: ZOOM R B S R _ 1 Aspect: THROUGH R B S R _ 3 3D DNR : OFF R B N R _ 0 3D DNR : Level1 R B N R _ 1 3D DNR : Level2 R B N R _ 2 3D DNR : Level3 R B N R _ 3 IP Conversion: 2D R B I P _ 0 IP Conversion: 3D R B I P _ 1 IP Conversion: Film R B I P _ 2 Input Signal: Auto I B S I _ 0 Input Signal: RGB I B S I _ 1 Input Signal: Component I B S I _ 2 HDMI_Setting : Nmal H M B D _ 1 HDMI_Setting : Expand H M B D _ 2 OK OK OK OK OK Common setting f RGB&HDMI input

15 VP4001 RS-232C Control Specification Page: 15 / Revision histy Ver. Date Owner Change description /07/06 Marantz America, Inc. Issued Revision1.0