TECHNICAL CP-SX1350. User's Manual - Operating Guide. Dimensions. Projector. [unit: mm]

Transcription

1 INTER M1-D INPUT LENS SHIFT FOCUS ZOOM RESET COMPONENT VIDEO STANDBY/ON TEMP LAMP MENU Projector CP-SX1350 User's Manual - Operating Guide TECHNICAL KEYSTONE SEARCH RGB BNG S-VIDEO Dimensions [unit: mm] (at the bottom of lens position) to (at the top of lens position) 1

2 Example Of Computer Signal Resolution H V fh (khz) fv (Hz) Rating Signal mode Display mode VESA TEXT Zoom in VESA VGA (60Hz) Zoom in Mac13"mode Zoom in VESA VGA (72Hz) Zoom in VESA VGA (75Hz) Zoom in VESA VGA (85Hz) Zoom in VESA SVGA (56Hz) Zoom in VESA SVGA (60Hz) Zoom in VESA SVGA (72Hz) Zoom in VESA SVGA (75Hz) Zoom in VESA SVGA (85Hz) Zoom in Mac16"mode Zoom in VESA XGA (60Hz) Zoom in VESA XGA (70Hz) Zoom in VESA XGA (75Hz) Zoom in VESA XGA (85Hz) Zoom in VESA SXGA (75Hz) VESA SXGA (60Hz) VESA SXGA (60Hz) VESA SXGA (75Hz) VESA SXGA + (60Hz) VESA UXGA (60Hz) Zoom out NOTE Be sure to check jack type, signal level, timing and resolution before connecting this projector to a computer. Some computers may hove multiple display screen modes. Use of some of these modes will not be possible with this projector. Depending on the input signal, full-size display may not be possible in some cases. Refer to the number of display pixels above. Although the projector can display signals with resolution up to UXGA (1600 x 1200), the signal will be converted to the projector s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and projector panel are identical. Automatically adjustment may not function correctly with some input signals. The image may not be displayed correctly when the input sync. signal is a composite sync. or a sync. on G. 2

3 Initial Signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the PICTURE-2 menu. DATA Back porch b Front porch d Display interval c DATA Back porch b Front porch d Display interval c H. Sync. V. Sync. Sync. a Sync. a Computer / Horizontal signal timing (µs) Signal a b c d TEXT VGA (60Hz) Mac 13"mode VGA (72Hz) VGA (75Hz) VGA (75Hz) SVGA (56Hz) SVGA (60Hz) SVGA (72Hz) SVGA (75Hz) SVGA (85Hz) Mac 16"mode XGA (60Hz) XGA (70Hz) XGA (75Hz) XGA (85Hz) (75Hz) (60Hz) (60Hz) (75Hz) (60Hz) (60Hz) Computer / Vertical signal timimg (lines) Signal a b c d TEXT VGA (60Hz) Mac 13"mode VGA (72Hz) VGA (75Hz) VGA (75Hz) SVGA (56Hz) SVGA (60Hz) SVGA (72Hz) SVGA (75Hz) SVGA (85Hz) Mac 16"mode XGA (60Hz) XGA (70Hz) XGA (75Hz) XGA (85Hz) (75Hz) (60Hz) (60Hz) (75Hz) (60Hz) (60Hz)

4 Connection To The Ports A RGB e w q = - D-Sub 15 pin shrink jack B D E AUDIO IN1 AUDIO IN2 RGB BNC A R/CR/PR G/Y B/CB/PB H V RGB OUT REMOTE CONTROL AUDIO OUT C M CR/PR Ca/Pa R-AUDIO IN-L Y VIDEO H CONTROL NETWORK S-VIDEO Video signal: RGB separate, Analog, 0.7 Vp-p, 75 Ω terminator (positive) H./V. sync. Signal: TTL level (positive/negative) Composite sync. Signal: TTL level Pin Signal Pin Signal Pin Signal 1 Video input Red 6 Ground Red Video input Green 7 Ground Green = SDA (DDC) 3 Video input Blue 8 Ground Blue q H./Composite sync w V. sync. 5 Ground 0 Ground e SCL (DDC) B M1-D g fdsa\] [po iuytrewq= Type: T.M.D.S. Amplitude differential: DC mv / AC 1.56 Vp-p Amplitude: TTL level (positive/negative) 4 M1-D jack Pin Signal Pin Signal Pin Signal 1 T.M.D.S. Data2 + - T.M.D.S. Data1 + o T.M.D.S. Data0 + 2 T.M.D.S. Data2 - = T.M/D.S. Data1 - p T.M.D.S. Data0-3 T.M.D.S. Data2 Return q T.M.D.S. Data1 Return [ T.M.D.S. Data0 Return 4 T.M.D.S. Clock Return w T.M.D.S. Clock + ] USB +5V DC Input 5 - e T.M.D.S. Clock - \ DDC & USB Return 6 V. Sync. r USB Date + a DDC Date (SDA) 7 - t USB Date - s DDC Clock (SCL) 8 Hot Plug Detect (+5V DC Output) y - d DDC +5V DC Input 9 - u - f i - g - C BNC (R,G,B,H,V) BNC jack x5 Video: Analog 0.7 Vp-p, 75 Ω terminator H/V. sync. : TTL level (positive/negative) Composite sync. : TTL level D AUDIO IN 1, E AUDIO IN 2, H AUDIO IN R, L, M AUDIO OUT 3.5 dia. Stereo mini jack 200 mvrms, 57k Ω terminator

5 Connection To The Ports (continued) O L N AUDIO IN1 AUDIO IN2 RGB REMOTE CONTROL AUDIO OUT RGB OUT CR/PR Ca/Pa Y CONTROL NETWORK K I VIDEO IN RCA jack System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL ± 0.1 Vp-p at 75 Ω terminator Mini Din 4 pin jack R/CR/PR G/Y B/CB/PB H V R-AUDIO IN-L VIDEO S-VIDEO I J J S-VIDEO Pin Signal K COMPONENT (CR/PR, CB/PB, Y) RCA jack x3 System: 525i (480i), 525p (480p), 625i (576i), 720p, 1080i/1035i Y signal: 1.0 ± 0.1 Vp-p at 75 Ω terminated with composite sync. CB/PB signal: 0.7 ± 0.1 Vp-p at 75 Ω terminated CR/PR signal: 0.7 ± 0.1 Vp-p at 75 Ω terminated BNC Color signal: Vp-p (NTSC, burst), 75 Ω terminator 1 Color signal: Vp-p (PAL/SECAM, burst), 75 Ω terminator 2 Brightness signal: 1.0 Vp-p, 75 Ω terminator 3 Ground 4 Ground L RGB OUT e w q = - D-Sub 15 pin shrink jack Video signal: RGB separate, Analog, 0.7 Vp-p, 75 Ω terminator (positive) H./V. sync. Signal: TTL level (positive/negative) Composite sync. Signal: TTL level Pin Signal Pin Signal Pin Signal 1 Video output Red 6 Ground Red Video output Green 7 Ground Green = - 3 Video output Blue 8 Ground Blue q H./Composite sync w V. sync. 5 Ground 0 Ground e - N REMOTE CONTROL 3.5 dia. Stereo mini jack To be connected with the remote control that came with the projector. O DC OUT 5

6 Connection To The Ports (continued) F G AUDIO IN1 REMOTE CONTROL CONTROL NETWORK AUDIO IN2 RGB RGB OUT AUDIO OUT CR/PR Ca/Pa Y R/CR/PR G/Y B/CB/PB H V R-AUDIO IN-L VIDEO S-VIDEO BNC F CONTROL Computer side CONTROL port D-Sub 9 pin plug D-Sub 9 pin jack - RD TD - GND - RTS CTS CD 2 RD 3 TD 4 DTR 5 GND 6 DSR 7 RTS 8 DTS 9 RI D-Sub 9 pin jack RS-232C port D-Sub 9 pin plug G NETWORK RJ-45 (10BASE-T) jack memo About the details of RS-232C communication, please refer to the following page. 6

7 RS-232C Communication Connecting The Cable Turn off the projector and the computer power supplies. Connect the CONTROL port of the projector with a RS-232C port of the computer by a RS-232C cable. Use the cable that fulfills the specification shown in the previous page. Turn on the computer power supply and after the computer has started up, turn on the projector power supply. Communications ting 19200bps, 8N1 1. Protocol Consist of header (7 bytes) + command data (6 bytes). 2. Header BE + EF CRC_low + CRC_high CRC_low : Lower byte of CRC flag for command data CRC_high : Upper byte of CRC flag for command data 3. Command data Command Data Chart byte_0 byte_1 byte_2 byte_3 byte_4 byte_5 Action Type ting code low high low high low high Action (byte_0-1) Action Classification Content 1 SET Change setting to desired value. 2 GET Read projector internal setup value. 4 INCREMENT Increment setup value by 1. 5 DECREMENT Decrement setup value by 1. 6 EXECUTE Run a command. 7

8 Requesting projector status (Get command) (1) Send the request code Header + Command data ( 02H + 00H + type (2 bytes)+ 00H + 00H ) from the computer to the projector. (2) The projector returns the response code 1DH + data (2 bytes) to the computer. Changing the projector settings ( command) (1) Send the setting code Header + Command data ( 01H + 00H + type (2 bytes) + setting code (2 bytes)) from the computer to the projector. (2) The projector changes the setting based on the above setting code. (3) The projector returns the response code 06H to the computer. Using the projector default settings (Reset Command) (1) The computer sends the default setting code Header + Command data ( 06H + 00H + type (2 bytes) + 00H + 00H ) to the projector. (2) The projector changes the specified setting to the default value. (3) The projector returns the response code 06H to the computer. Increasing the projector setting value (Increment command) (1) The computer sends the increment code Header + Command data ( 04H + 00H + type (2 bytes) + 00H + 00H ) to the projector. (2) The projector in creases the setting value on the above setting code. (3) The projector returns the response code 06H to the computer. Decreasing the projector setting value (Decrement command) (1) The computer sends the decrement code Header + Command data ( 05H + 00H + type (2 bytes) + 00H + 00H ) to the projector. (2) The projector decreases the setting value on the above setting code. (3) The projector returns the response code 06H to the computer. When the projector cannot understand the received command When the projector cannot understand the received command, the error code 15H is sent back to the computer. Sometimes the projector cannot properly receive the command. In such a case, the command is not executed and the error code 15H is sent back to the computer. If this error code is returned, send the same command again. When the projector cannot execute the received command. When the projector cannot execute the received command, the error code 1cH + xxxxh is sent back to the computer. When the data length is greater than indicated by the data length code, the projector ignore the excess data code. Conversely when the data length is shorter than indicated by the data length code, an error code will be returned to the computer. NOTE Operation cannot be guaranteed when the projector receives an undefined command or data. Provide an interval of at least 40ms between the response code and any other code. The projector outputs test data when the power supply is switched ON, and when the lamp is lit. Ignore this data. Commands are not accepted during warm-up. 8

9 Command Data Chart Command data Names Operation type Header CRC Action Type ting code Get BE EF B9 D Keystone V Increment BE EF DF D Decrement BE EF E D Keystone V Reset Execute BE EF D C Get BE EF E9 D B Keystone H Increment BE EF F D B Decrement BE EF E D B Keystone H Reset Execute BE EF D Get BE EF D Brightness Increment BE EF EF D Decrement BE EF E D Brightness Reset Execute BE EF D Get BE EF FD D Contrast Increment BE EF B D Decrement BE EF A D Contrast Reset Execute BE EF A4 D :3 BE EF E D :9 BE EF E D Aspect SMALL BE EF FE D NORMAL BE EF E DD REAL BE EF E D Get BE EF AD D NORMAL BE EF B Whisper WHISPER BE EF AB Get BE EF Normal BE EF C7 D H Inverse BE EF D Mirror V lnverse BE EF A7 D H&V Inverse BE EF D Get BE EF F4 D (This table is continued to the following page.) 9

10 Command Data Chart (continued) 10 Names Operation type Header Language Gamma Custom Gamma Custom Color Temp Custom User R Custom User G Command data CRC Action Type ting code ENGLISH BE EF F7 D FRANÇAIS BE EF D DEUTSCH BE EF D ESPAÑOL BE EF D ITALIANO BE EF D NORSK BE EF A7 D NEDERLANDS BE EF D PORTUGUÊS BE EF C7 D BE EF D BE EF A7 D BE EF DE BE EF D A 00 SVENSKA BE EF C7 D B 00 BE EF F7 D C 00 SUOMI BE EF D D 00 POLSKI BE EF D E 00 TÜRKÇE BE EF D F 00 Get BE EF C4 D NORMAL BE EF C7 F A CINEMA BE EF F A DYNAMIC BE EF A7 F A CUSTOM BE EF FD A Get BE EF F4 F A Get BE EF F A Increment BE EF E F A Decrement BE EF BF F A USER BE EF B F B HIGH BE EF B F B MIDDLE BE EF B F B LOW BE EF B F B Get BE EF C8 F B BE EF F B BE EF C7 F B BE EF F7 F B BE EF F B BE EF F B BE EF F B Get BE EF F B BE EF F B BE EF F B BE EF B3 F B BE EF F B BE EF D3 F B BE EF F B Get BE EF F B (This table is continued to the following page.)

11 Command Data Chart (continued) Names Operation type Header Custom User B Color Balance R Color Balance R Reset Color Balance G Color Balance G Reset Color Balance B Color Balance B Reset Command data CRC Action Type ting code 50 BE EF EF F B BE EF F F B BE EF F F B BE EF DF F B BE EF F F B BE EF BF F B Get BE EF C F B Get BE EF D Increment BE EF D Decrement BE EF B6 D Execute BE EF D Get BE EF B5 D Increment BE EF D3 D Decrement BE EF D Execute BE EF DB Get BE EF D Increment BE EF D Decrement BE EF F2 D Execute BE EF D0 D Get BE EF F Sharpness Increment BE EF Decrement BE EF Sharpness Reset Execute BE EF C4 D Get BE EF B Color Increment BE EF D Decrement BE EF Color Reset Execute BE EF D A Get BE EF Tint Increment BE EF F Decrement BE EF FE Tint Reset Execute BE EF C D B My Memory Load My Memory Save 1 BE EF E D BE EF E D BE EF E D BE EF FE D BE EF F2 D BE EF D BE EF D BE EF D (This table is continued to the following page.) 11

12 Command Data Chart (continued) Names Operation type Header V Position Command data CRC Action Type ting code Get BE EF D Increment BE EF B Decrement BE EF BA V Position Reset Execute BE EF E0 D H Position Get BE EF F Increment BE EF Decrement BE EF H Position Reset Execute BE EF C D H Phase H Size Get BE EF Increment BE EF F Decrement BE EF FE Get BE EF B Increment BE EF D Decrement BE EF H Size Reset Execute BE EF D Over Scan Get BE EF Increment BE EF F Decrement BE EF Over Scan Reset Execute BE EF EC D Color Space Component Video Format 3D-YCS AUTO BE EF E RGB BE EF E SMPTE240 BE EF E REC709 BE EF FE REC601 BE EF CE Get BE EF D COMPONENT BE EF A D SCART RGB BE EF DA D Get BE EF D AUTO BE EF E A 00 NTSC BE EF FE PAL BE EF E SECAM BE EF E NTSC 4.43 BE EF E M-PAL BE EF FE N-PAL BE EF E Get BE EF D TURN OFF BE EF E A TURN ON BE EF A Get BE EF D A (This table is continued to the following page.) 12

13 Command Data Chart (continued) Names Operation type Header Video NR Command data CRC Action Type ting code LOW BE EF MIDDLE BE EF D HIGH BE EF Get BE EF Auto Adjust Execute BE EF D A Auto off Auto Search Blank Color Blank on/off Startup Menu Position V Menu Position V Reset Menu Position H Menu Position H Reset Message Get BE EF Increment BE EF E Decrement BE EF BF TURN OFF BE EF B6 D TURN ON BE EF D Get BE EF D My Screen BE EF FB CA Original BE EF FB E Blue BE EF CB D White BE EF B D Black BE EF B D Get BE EF D TURN OFF BE EF FB D TURN ON BE EF B D Get BE EF C8 D My Screen BE EF CB CB Original BE EF B D TURN OFF BE EF B D Get BE EF D Get BE EF D Increment BE EF D Decrement BE EF F7 D Execute BE EF A8 C Get BE EF D Increment BE EF D Decrement BE EF B3 D Execute BE EF DC C TURN OFF BE EF F D TURN ON BE EF F D Get BE EF BC D (This table is continued to the following page.) 13

14 Command Data Chart (continued) Names Operation type Header Volume Mute Command data CRC Action Type ting code Get BE EF D Increment BE EF D Decrement BE EF D TURN OFF BE EF D TURN ON BE EF D6 D Get BE EF D Lamp Time Get BE EF C2 FF Lamp Time Reset Execute BE EF DC Filter Time Get BE EF C2 F A Filter Time Reset Execute BE EF C Magnify Freeze Power Input Source Get BE EF C D Increment BE EF A D Decrement BE EF CB D Normal BE EF D Freeze BE EF D Get BE EF B0 D TURN OFF BE EF A D TURN ON BE EF BA D Get BE EF D (Example Return) (Off) (On) (Cool down) M1-D BE EF E D RGB BE EF FE D BNC BE EF E D Video BE EF E D S-Video BE EF E D Component BE EF AE D Get BE EF CD D BE EF D9 D Error Status Get (Example of Return) (Normal) (Cover-error) (Fan-error) (Lamp-error) (Temp-error) (Air flow- (Lamp- (Cool-error) (Filter-Error) error) Time-over) (This table is continued to the following page.) 14

15 Command Data Chart (continued) Names Operation type Header PinP Size PinP Position PinP Audio Ch PinP Input Myscreen Lock IR Remote Front IR Remote Rear IR Remote Top Command data CRC Action Type ting code Off BE EF FE Large BE EF E Small BE EF E Get BE EF CD Upper Left BE EF Upper Right BE EF Bottom Left BE EF Bottom Right BE EF F Get BE EF RGB BE EF BA Video BE EF A Get BE EF Video BE EF D S-Video BE EF Get BE EF Off BE EF B EF C On BE EF AB EE C Get BE EF EF C Off BE EF FF On BE EF F Get BE EF CC Off BE EF On BE EF Get BE EF Off BE EF On BE EF D Get BE EF (This table is continued to the following page.) 15

16 Command Data Chart (continued) Names Operation type Header Power Up Source Auto Adjust Enable Internal Speaker Lens Lock Remote ID Lens Command data CRC Action Type ting code Last Ch BE EF E D M1-D BE EF AE D RGB BE EF E D BNC BE EF E D Component BE EF E D S-Video BE EF E D Video BE EF CE D Get BE EF D D DISABLE BE EF A2 D ENABLE BE EF D Get BE EF D TURN OFF BE EF E D C TURN ON BE EF FE D C Get BE EF D D C TURN OFF BE EF FF TURN ON BE EF F Get BE EF CC All BE EF F BE EF F BE EF FF BE EF F Get BE EF AC AUTO BE EF F D BE EF AF D BE EF F D BE EF CF D BE EF FF DA BE EF F DB Get BE EF C D