Digital Projector X30N/X35N

Transcription

1 Digital Projector X30N/X35N Operator's Guide TECHNICAL Warranty 3M warrants that when the 3M Product is used according to 3M s Intended Use Statement ( it will perform satisfactorily for the warranted durability period as stated in the applicable 3M Product Manual in effect at the time of purchase. The warranties stated in the applicable 3M Product Manuals are exclusive and are made in place of any and all express or implied warranties or conditions, including any implied warranty of merchantability or fitness for a particular purpose, or any industry practice or custom or trade usage. Important Notice All statements, technical information, and recommendations related to 3M s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly 1

2 Example of computer signal 3M Digital Projector X30N/X35N Example of computer signal Resolution (H x V) H. frequency (khz) V. frequency (Hz) Rating Signal mode 720 x VESA 640 x VESA 640 x VESA 640 x VESA 640 x VESA 800 x VESA 800 x VESA 800 x VESA 800 x VESA 800 x VESA 832 x Mac 16 mode 1024 x VESA 1024 x VESA 1024 x VESA 1024 x VESA 1152 x VESA 1152 x 864 (75Hz) 1280 x VESA 1280 x VESA 1280 x 800 (60Hz) 1280 x VESA 1280 x 960 (60Hz) 1280 x VESA 1280 x VESA 1280 x VESA 1400 x VESA 1600 x VESA NOTE cases. Refer to the number of display pixels above. before being displayed. The best display performance will be achieved if the 2 3M All Rights Reserved.

3 Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some Back porch (B) Front porch (D) Back porch (b) Front porch (d) Data Active video (C) Data H. Sync. V. Sync. Sync (A) Sync (a) Active video (c) Resolution Vertical signal timing (lines) (H x V) (A) (B) (a) (b) (c) (d) Signal mode 720 x x x x x x x x x x x Mac 16" mode 1024 x x x x x x 864 (75Hz) 1280 x x x 800 (60Hz) 1280 x x 960 (60Hz) 1280 x x x x x M All Rights Reserved. 3

4 Connection to the ports 3M Digital Projector X30N/X35N NOTICE BATTERY C B LAN A A COMPUTER IN1, B COMPUTER IN2, C MONITOR OUT Y, Analog, Analog, r/pr, Analog, Pin Signal Pin Signal A 12 5 B, C V. sync., 8 A 15 B, C 4 3M All Rights Reserved.

5 Connection to the ports (continued) LAN G BATTERY D E F H COMPONENT D Y, E Cb/Pb F Cr/Pr Port Signal Y G S-VIDEO Pin Signal H VIDEO 3M All Rights Reserved. 5

6 Connection to the ports (continued) LAN BATTERY I J K L M N I AUDIO IN1, J AUDIO IN2 AUDIO IN3 K R, L L AUDIO OUT M R, N L 6 3M All Rights Reserved.

7 Connection to the ports (continued) BATTERY Q LAN O P O USB Pin Signal P CONTROL please refer to the following page Pin Signal Pin Signal Pin Signal RTS Q LAN Pin Signal Pin Signal Pin Signal M All Rights Reserved. 7

8 Connection to the ports (continued) 3M Digital Projector X30N/X35N To input component video signal to COMPUTER IN ports ex. BATTERY LAN Y CB/PB C R/PR COMPONENT VIDEO OUT To input component video signal to the COMPUTER IN1 or IN2 port of the descriptions about COMPUTER IN1 and IN2 port ( 3). To input SCART RGB signal; ex. BATTERY LAN (plug) dealer. 8 3M All Rights Reserved.

9 3M Digital Projector X30N/X35N RS-232C Communication command table ( 17). Connection CONTROL 3. on. OPTION menu - SERVICE - 4. COMMUNICATION in the Operator's Guide) RS-232C CONTROL RS-232C Cable (cross) of the computer CONTROL port RTS (7) (7) RTS RI (9) (9) 3M All Rights Reserved. 9

10 RS-232C Communication (continued) 3M Digital Projector X30N/X35N Communicaion settings 1. Protocol 2. Command format ("h" shows hexadecimal) Action Increment setup value. Header Header code Packet size Action Type Setting code H H H H H H BEh 03h 06h 00h (ah) 01h 00h (bh) (ch) (ah) 02h 00h (bh) 00h 00h (ah) 04h 00h (bh) 00h 00h (ah) 05h 00h (bh) 00h 00h (ah) 06h 00h (bh) 00h 00h [Header code] [Packet] [Data size] ~ 4. 5, 6, refer to table ( 17). [Action] Set functional code to byte number 7, 8. <SET < ( above). [Type] [Setting code] 9 12, refer to table ( 17). 10 3M All Rights Reserved.

11 RS-232C Communication (continued) 3. Response code / Error code ("h" shows hexadecimal) (1) ACK reply : 06h (2) NAK reply : 15h returns the error code. In such a case, check the sending code and send the same command again. (3) Error reply : 1Ch h (4) Data reply : 1Dh + xxxxh the responce code and 2 bytes of data. NOTE manual for each devices, and connect them correctly with suitable cables. command or data. code. when the lamp is lit. Ignore this data. When the data length is greater than indicated by the data length code, the code to the computer. 3M All Rights Reserved. 11

12 Command Control via the Network 3M Digital Projector X30N/X35N command table ( 17). Connection LAN Turn the computer on, and after the computer has started up turn the 3. LAN cable (CAT-5 or greater) LAN LAN 12 3M All Rights Reserved.

13 Command Control via the Network Communicaion Port The following two ports are assigned for the command control. Port Settings Network Control Port1 (Port: 23) Network Control Port2 (Port: 9715) Port open Authentication Port open Authentication [Enable] check box to open [Network Control Port1 (Port: 23)] [Enable] check box for the [Authentication] setting when authentication is required. [Enable] check box to open [Network Control Port2 (Port: 9715)] [Enable] check box for the [Authentication] setting when authentication is required. When the authentication setting is enabled, the following settings are required. Security Settings Network Control Authentication Password Authentication Password Enter the desired authentication password. This setting will be the same for [Network Control Port1 (Port: 23)] and [Network Control Port2 (Port: 9715)]. 3M All Rights Reserved. 13

14 Command Control via the Network (continued) 3M Digital Projector X30N/X35N Command control settings [TCP #23] 1. Command format 2. Response code / Error code ("h" shows hexadecimal) (1) ACK reply : 06h ( 9). (2) NAK reoly : 15h ( 9). (3) Error reply : 1Ch h ( 9). (4) Data reply : 1Dh + xxxxh ( 9). (5) Authentication error reply : 1Fh h [TCP #9715] 1. Command format The commands some datum are added to the head and the end of the ones of Header bytes 1 byte 1 byte [Header] [Data Length] [RS-232C commands] ( 9). [Check Sum] This is the value to make zero on the addition of the lower 8 bits from the header to the checksum. [Connection ID] Random value from 0 to 255 (This value is attached to the reply data). NOTE other code. 14 3M All Rights Reserved.

15 Command Control via the Network (continued) 2. Response code / Error code ("h" shows hexadecimal) (1) ACK reply : 06h + h ( ) (2) NAK reoly : 15h + h (3) Error reply : 1Ch h + h (4) Data reply : 1Dh + xxxxh + h (5) Authentication error reply : 1Fh h + h (6) Projector busy reply: 1Fh + h + h returens the error code. In such a case, check the sending code and send the same command again. Automatic Connection Break communication for 30 seconds after being established. Authentication this received 8 bytes and the authentication password and digest this data with 1) send the data. 6) When the sending data is correct, the command will be performed and the NOTE the authentication data can be omitted when the same connection. 3M All Rights Reserved. 15

16 Network Bridge Communication 3M Digital Projector X30N/X35N controlled from the computer as a network terminal. 3.7 Controlling the external device via the projector(using the NETWORK BRIDGE function) - Network Guide. Connection 1. LAN cable. 2. CONTROL 3. on.. ( OPTION menu - 4. SERVICE - COMMUNICATION in the Operator's Guide) LAN LAN CONTROL RS-232C 16 3M All Rights Reserved.

17 Network Bridge Communication Communication settings OPTION menu - SERVICE - COMMUNICATION in the Operator's Guide) Item PARITY Start bit Stop bit Transmission method 4800bps / 9600bps / 19200bps / 38400bps / NOTE manual for each devices, and connect them correctly with suitable cables. beore connecting them Transmission method- Network Guide. 3M All Rights Reserved. 17

18 RS-232C Communication / Network command table 3M Digital Projector X30N/X35N Names Operation Type Header Command Data CRC Action Type Setting Code Power Set Turn off BE EF A D Turn on BE EF BA D Get BE EF D [Example return] [Off] [On] [Cool down] Input Source Set COMPUTER IN1 BE EF FE D COMPUTER IN2 BE EF E D COMPONENT BE EF AE D S-VIDEO BE EF E D VIDEO BE EF E D Get BE EF CD D Error Status Get BE EF D9 D [Example return] [Normal] [Cover error] [Fan error] [Lamp error] MAGNIFY Get BE EF C D Increment BE EF A D Decrement BE EF CB D FREEZE Set NORMAL BE EF D FREEZE BE EF D Get BE EF B0 D PICTURE MODE Set NORMAL BE EF F BA CINEMA BE EF B3 F BA DYNAMIC BE EF E3 F BA BOARD(BLACK) BE EF E3 EF BA BOARD(GREEN) BE EF EE BA WHITEBOARD BE EF EE BA DAYTIME BE EF E3 C BA Get BE EF F BA [Example return] [Normal] [Cinema] [Dynamic] [Custom] [BOARD(BLACK)] [BOARD(GREEN)] [WHITEBOARD] [DAY TIME] BRIGHTNESS Get BE EF D Increment BE EF EF D Decrement BE EF E D BRIGHTNESS Reset Execute BE EF D CONTRAST Get BE EF FD D Increment BE EF B D Decrement BE EF A D CONTRAST Reset Execute BE EF A4 D (continued on next page) 18 3M All Rights Reserved.

19 RS-232C Communication / Network command table (continued) Header Action Type GAMMA Set 1 DEFAULT BE EF E A CUSTOM BE EF FD A DEFAULT BE EF E A CUSTOM BE EF FC A DEFAULT BE EF E A CUSTOM BE EF FC A DEFAULT BE EF F7 E A CUSTOM BE EF F7 FD A DEFAULT BE EF C7 EB A CUSTOM BE EF C7 FF A DEFAULT BE EF EA A CUSTOM BE EF FE A Get BE EF F4 F A User Gamma Pattern Set Off BE EF FB FA steps gray scale BE EF B FB steps gray scale BE EF B FB Ramp BE EF B FA Get BE EF C8 FA User Gamma Point 1 Get BE EF FE Increment BE EF E FE Decrement BE EF BF FF User Gamma Point 1 Reset Execute BE EF C User Gamma Point 2 Get BE EF F4 FF Increment BE EF FF Decrement BE EF FE User Gamma Point 2 Reset Execute BE EF A4 C User Gamma Point 3 Get BE EF B0 FF Increment BE EF D6 FF Decrement BE EF FE User Gamma Point 3 Reset Execute BE EF E0 C User Gamma Point 4 Get BE EF C FE Increment BE EF A FE Decrement BE EF FB FF User Gamma Point 4 Reset Execute BE EF C C User Gamma Point 5 Get BE EF FF Increment BE EF E FF Decrement BE EF F FE User Gamma Point 5 Reset Execute BE EF C User Gamma Point 6 Get BE EF C4 FE Increment BE EF A2 FE Decrement BE EF FF User Gamma Point 6 Reset Execute BE EF C User Gamma Point 7 Get BE EF FE Increment BE EF E6 FE Decrement BE EF FF User Gamma Point 7 Reset Execute BE EF D0 C (continued on next page) 3M All Rights Reserved. 19

20 RS-232C Communication / Network command table (continued) Names Operation Type Header Command Data CRC Action Type Setting Code User Gamma Point 8 Get BE EF C FF Increment BE EF A FF Decrement BE EF CB FE User Gamma Point 8 Reset Execute BE EF C C COLOR TEMP Set 1 HIGH BE EF B F B CUSTOM BE EF CB F B MID BE EF B F B CUSTOM BE EF B F B LOW BE EF B F B CUSTOM BE EF AB F B Hi-BRIGHT-1 BE EF B F B CUSTOM BE EF FB FF B Hi-BRIGHT-2 BE EF AB F B CUSTOM BE EF B FE B Hi-BRIGHT-3 BE EF B F B0 30 0A 00 6 CUSTOM BE EF B FE B0 30 1A 00 Get BE EF C8 F B COLOR TEMP GAIN R Get BE EF F B Increment BE EF F B Decrement BE EF F B COLOR TEMP GAIN R Reset Execute BE EF C COLOR TEMP GAIN G Get BE EF F B Increment BE EF F B Decrement BE EF C7 F B COLOR TEMP GAIN G Reset Execute BE EF EC C COLOR TEMP GAIN B Get BE EF C F B Increment BE EF EA F B Decrement BE EF B F B COLOR TEMP GAIN B Reset Execute BE EF F8 C COLOR TEMP OFFSET R COLOR TEMP OFFSET R Reset COLOR TEMP OFFSET G COLOR TEMP OFFSET G Reset COLOR TEMP OFFSET B COLOR TEMP OFFSET B Reset Get BE EF F B Increment BE EF F B Decrement BE EF B3 F B Execute BE EF C A Get BE EF F B Increment BE EF F B Decrement BE EF F7 F B Execute BE EF BC C B Get BE EF BC F B Increment BE EF DA F B Decrement BE EF B F B Execute BE EF C8 C C (continued on next page) 20 3M All Rights Reserved.

21 RS-232C Communication / Network command table (continued) Names Operation Type Header Command Data CRC Action Type Setting Code COLOR Get BE EF B Increment BE EF D Decrement BE EF COLOR Reset Execute BE EF D A TINT Get BE EF Increment BE EF F Decrement BE EF FE TINT Reset Execute BE EF C D B SHARPNESS Get BE EF F Increment BE EF Decrement BE EF SHARPNESS Reset Execute BE EF C4 D ACTIVE IRIS Set OFF BE EF B THEATER BE EF CB 2F PRESENTATION BE EF B 2E Get BE EF MY MEMORY Load Set 1 BE EF E D BE EF E D BE EF E D BE EF FE D MY MEMORY Save Set 1 BE EF F2 D BE EF D BE EF D BE EF D ASPECT Set 4:3 BE EF E D :9 BE EF E D :9 BE EF CE D :10 BE EF E D A 00 NORMAL BE EF E DD Get BE EF AD D OVER SCAN Get BE EF Increment BE EF F Decrement BE EF OVER SCAN Reset Execute BE EF EC D V POSITION Get BE EF D Increment BE EF B Decrement BE EF BA V POSITION Reset Execute BE EF E0 D H POSITION Get BE EF F Increment BE EF Decrement BE EF H POSITION Reset Execute BE EF C D H PHASE Get BE EF Increment BE EF F Decrement BE EF FE (continued on next page) 3M All Rights Reserved. 21

22 RS-232C Communication / Network command table (continued) Names Operation Type Header Command Data CRC Action Type Setting Code H SIZE Get BE EF B Increment BE EF D Decrement BE EF H SIZE Reset Execute BE EF D AUTO ADJUST EXECUTE Execute BE EF D A PROGRESSIVE Set OFF BE EF A TV BE EF DA FILM BE EF A Get BE EF VIDEO NR Set LOW BE EF MID BE EF D HIGH BE EF Get BE EF COLOR SPACE Set AUTO BE EF E RGB BE EF E SMPTE240 BE EF E REC709 BE EF FE REC601 BE EF CE Get BE EF D COMPONENT Set COMPONENT BE EF A D SCART RGB BE EF DA D Get BE EF D S-VIDEO FORMAT Set AUTO BE EF E A 00 NTSC BE EF PAL BE EF SECAM BE EF NTSC4.43 BE EF M-PAL BE EF N-PAL BE EF Get BE EF C-VIDEO FORMAT Set AUTO BE EF A A 00 NTSC BE EF C PAL BE EF SECAM BE EF NTSC4.43 BE EF M-PAL BE EF C N-PAL BE EF Get BE EF COMPUTER IN1 Set AUTO BE EF CE D SYNC ON G OFF BE EF E D Get BE EF D D COMPUTER IN2 Set AUTO BE EF D SYNC ON G OFF BE EF A2 D Get BE EF F1 D (continued on next page) 22 3M All Rights Reserved.

23 RS-232C Communication / Network command table (continued) Names Operation Type Header Command Data CRC Action Type Setting Code FRAME LOCK COMPUTER IN1 FRAME LOCK COMPUTER IN2 Set OFF BE EF B C ON BE EF AB C Get BE EF C Set OFF BE EF B C ON BE EF B C Get BE EF C AUTO KEYSTONE V EXECUTE Execute BE EF E5 D D KEYSTONE V Get BE EF B9 D Increment BE EF DF D Decrement BE EF E D KEYSTONE V Reset Execute BE EF D C ECO MODE Set NORMAL BE EF B ECO BE EF AB Get BE EF MIRROR Set NORMAL BE EF C7 D H:INVERT BE EF D V:INVERT BE EF A7 D H&V:INVERT BE EF D Get BE EF F4 D STANDBY MODE Set NORMAL BE EF D6 D SAVING BE EF D Get BE EF E5 D MONITOR OUT - COMPUTER IN1 MONITOR OUT - COMPUTER IN2 MONITOR OUT - COMPONENT MONITOR OUT - S-VIDEO MONITOR OUT - VIDEO MONITOR OUT - STANDBY VOLUME - COMPUTER IN1 Set COMPUTER IN1 BE EF E F B OFF BE EF CE B B0 20 FF 00 Get BE EF D F B Set COMPUTER IN2 BE EF CE F B OFF BE EF FE B B4 20 FF 00 Get BE EF D F B Set COMPUTER IN1 BE EF F2 F B COMPUTER IN2 BE EF F B OFF BE EF B B5 20 FF 00 Get BE EF C1 F B Set COMPUTER IN1 BE EF F B COMPUTER IN2 BE EF F B OFF BE EF B B2 20 FF 00 Get BE EF B5 F B Set COMPUTER IN1 BE EF C2 F B COMPUTER IN2 BE EF F B OFF BE EF B B1 20 FF 00 Get BE EF F1 F B Set COMPUTER IN1 BE EF A F BF COMPUTER IN2 BE EF EA F BF OFF BE EF DA B BF 20 FF 00 Get BE EF F BF Get BE EF CD CC Increment BE EF AB CC Decrement BE EF A CD (continued on next page) 3M All Rights Reserved. 23

24 RS-232C Communication / Network command table (continued) Names Operation Type Header Command Data CRC Action Type Setting Code VOLUME - COMPUTER IN2 VOLUME - COMPONENT Get BE EF FD CD Increment BE EF B CD Decrement BE EF A CC Get BE EF CC Increment BE EF CC Decrement BE EF B6 CD VOLUME - S-VIDEO Get BE EF CD Increment BE EF CD Decrement BE EF C2 CC VOLUME - VIDEO Get BE EF CD Increment BE EF CD Decrement BE EF CC VOLUME - Get BE EF D9 CF F AUDIO OUT STANDBY Increment BE EF BF CF F Decrement BE EF E CE F MUTE Set OFF BE EF D ON BE EF D6 D Get BE EF D SPEAKER Set ON BE EF FE D C OFF BE EF E D C Get BE EF D D C AUDIO SOURCE - COMPUTER IN1 AUDIO SOURCE - COMPUTER IN2 AUDIO SOURCE - COMPONENT AUDIO SOURCE - S-VIDEO AUDIO SOURCE - VIDEO Set AUDIO IN1 BE EF E DC AUDIO IN2 BE EF E DC AUDIO IN3 BE EF E DD OFF BE EF FE DD Get BE EF CD DD Set AUDIO IN1 BE EF E DD AUDIO IN2 BE EF AE DD AUDIO IN3 BE EF E DC OFF BE EF CE DC Get BE EF FD DC Set AUDIO IN1 BE EF A2 DC AUDIO IN2 BE EF DC AUDIO IN3 BE EF C2 DD OFF BE EF DD Get BE EF DD Set AUDIO IN1 BE EF D6 DD AUDIO IN2 BE EF DD AUDIO IN3 BE EF B6 DC OFF BE EF DC Get BE EF DC Set AUDIO IN1 BE EF DD AUDIO IN2 BE EF DD AUDIO IN3 BE EF F2 DC OFF BE EF DC Get BE EF DC (continued on next page) 24 3M All Rights Reserved.

25 RS-232C Communication / Network command table (continued) Names Operation Type Header Command Data CRC Action Type Setting Code AUDIO OUT STANDBY Set AUDIO IN1 BE EF A DF F AUDIO IN2 BE EF A DF F AUDIO IN3 BE EF A DE F OFF BE EF EA DE F Get BE EF D9 DE F LANGUAGE Set ENGLISH BE EF F7 D FRANÇAIS BE EF D DEUTSCH BE EF D ESPAÑOL BE EF D ITALIANO BE EF D NORSK BE EF A7 D NEDERLANDS BE EF D PORTUGUÊS BE EF C7 D BE EF D BE EF A7 D BE EF DE BE EF D A 00 SVENSKA BE EF C7 D B 00 BE EF F7 D C 00 SUOMI BE EF D D 00 POLSKI BE EF D E 00 TÜRKÇE BE EF D F 00 Get BE EF C4 D MENU POSITION H Get BE EF D Increment BE EF D Decrement BE EF B3 D MENU POSITION H Reset Execute BE EF DC C MENU POSITION V Get BE EF D Increment BE EF D Decrement BE EF F7 D MENU POSITION V Reset Execute BE EF A8 C (continued on next page) 3M All Rights Reserved. 25

26 RS-232C Communication / Network command table (continued) Names Operation Type Header Command Data CRC Action Type Setting Code BLANK Set MyScreen BE EF FB CA ORIGINAL BE EF FB E BLUE BE EF CB D WHITE BE EF B D BLACK BE EF B D Get BE EF D BLANK On/Off Set OFF BE EF FB D ON BE EF B D Get BE EF C8 D START UP Set MyScreen BE EF CB CB ORIGINAL BE EF B D OFF BE EF B D Get BE EF D MyScreen Lock Set OFF BE EF B EF C ON BE EF AB EE C Get BE EF EF C MESSAGE Set OFF BE EF F D ON BE EF F D Get BE EF BC D TEMPLATE Set TEST PATTERN BE EF D DOT-LINE1 BE EF D3 D DOT-LINE2 BE EF D DOT-LINE3 BE EF B3 D DOT-LINE4 BE EF DB Get BE EF D TEMPLATE On/Off Set OFF BE EF BF D ON BE EF F D Get BE EF C D C. C. - DISPLAY Set OFF BE EF FA ON BE EF A AUTO BE EF A Get BE EF C C. C. - MODE Set CAPTIONS BE EF TEXT BE EF Get BE EF C. C. - CHANNEL Set 1 BE EF D BE EF BE EF B BE EF Get BE EF AUTO SEARCH Set OFF BE EF B6 D ON BE EF D Get BE EF D AUTO KEYSTONE Set OFF BE EF EA D F ON BE EF A D F Get BE EF D9 D F DIRECT ON Set OFF BE EF B ON BE EF AB Get BE EF (continued on next page) 26 3M All Rights Reserved.

27 RS-232C Communication / Network command table (continued) Names Operation Type Header Command Data CRC Action Type Setting Code AUTO OFF Get BE EF Increment BE EF E Decrement BE EF BF LAMP TIME Get BE EF C2 FF LAMP TIME Reset Execute BE EF DC FILTER TIME Get BE EF C2 F A FILTER TIME Reset Execute BE EF C MY BUTTON-1 Set COMPUTER IN1 BE EF A COMPUTER IN2 BE EF FA COMPONENT BE EF A S-VIDEO BE EF A VIDEO BE EF AA INFORMATION BE EF FA 3E AUTO KEYSTONE V BE EF A 3F MY MEMORY BE EF A 3F ACTIVE IRIS BE EF AA 3D PICTURE MODE BE EF A 3E FILTER RESET BE EF A 3C AV MUTE BE EF AA TEMPLATE BE EF CA B 00 MY IMAGE BE EF A 3D MESSENGER BE EF AA Get BE EF MY BUTTON-2 Set COMPUTER IN1 BE EF C COMPUTER IN2 BE EF COMPONENT BE EF S-VIDEO BE EF A VIDEO BE EF INFORMATION BE EF F AUTO KEYSTONE V BE EF E MY MEMORY BE EF E ACTIVE IRIS BE EF C PICTURE MODE BE EF F6 3F FILTER RESET BE EF C6 3D AV MUTE BE EF TEMPLATE BE EF B 00 MY IMAGE, BE EF A6 3C MESSENGER BE EF Get BE EF F MY SOURCE Set COMPUTER IN1 BE EF FA COMPUTER IN2 BE EF A 3A COMPONENT BE EF AA 3B S-VIDEO BE EF A VIDEO BE EF A Get BE EF C REMOTE FREQ. NORMAL Set OFF BE EF FF 3D ON BE EF F 3C Get BE EF CC 3D M All Rights Reserved. 27

28 RS-232C Communication / Network command table (continued) Names Operation Type Header Command Data CRC Action Type Setting Code REMOTE FREQ. HIGH Set OFF BE EF C ON BE EF D Get BE EF C MY IMAGE Set OFF BE EF A C IMAGE-1 BE EF AA C IMAGE-2 BE EF A C IMAGE-3 BE EF CA C IMAGE-4 BE EF FA C Get BE EF C MY IMAGE IMAGE-1 Delete Execute BE EF C MY IMAGE IMAGE-2 Delete Execute BE EF C MY IMAGE IMAGE-3 Delete Execute BE EF C9 C MY IMAGE IMAGE-4 Delete Execute BE EF BD C M All Rights Reserved.

29 PJLink command TM TM protocol are as given in the table below. Parameter or Response AVMT Power Status inquiry Input Source selection Input Source inquiry AV Mute AV Mute inquiry 3M All Rights Reserved. 29

30 PJLink command (continued) 3M Digital Projector X30N/X35N Parameter or Response Error Status inquiry 2nd byte The mearning of 0 to 2 is as given below inquiry 3M Responds with the factory information and so on 1 NOTE TM is the same as the password set in TM without authentication, do not set TM, see the web site of the Japan Business Machine and Information System Industries Association. 30 3M All Rights Reserved.