Box Camera FULL AHD OPERATION MANUAL M266-ABN

Transcription

1 M266-ABN FULL AHD Box Camera OPERATION MANUAL Thank you for choosing our high quality camera. Before attempting to connect operate this unit,please read and follow these instructions.

2 CONTENTS NOTICES FOR YOUR SAFETY FEATURES COMPONENTS OVERVIEW AND FUNCTION INSTALLATION CONNECTION DIMENSIONS SPECIFICATIONS OSD MENU STRUCTURE AHD (UP THE COAX) CAUTION These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Use Class 2 Power Supply Only 2

3 1. NOTICES This device complies with Part 15 of FCC regulations. Operation is subject to the following two conditions; 1. This device may not cause harmful interference. 2. This device may receive interference that can cause affect the opration of this equipment. Note - This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Caution - Alteration or modifications carried out without appropriate authorization may invalidate the user's right to operate the equipment. 1. A regulated DC12V 500mA power supply is recommended for use with this camera to ensure the best picture quality and stable operation. An unregulated power supply may cause damage to the camera. Using an unregulated power supply will void the product warranty. If your monitor is switched to high impedance, then please adjust accordingly. 2. Do not attempt to disassemble the camera to access internal components. Refer servicing to your dealer. 3. Never face the camera towards the sun or any bright or reflective light, which may cause smear on the picture and possible damage to the image sensor. 4. Do not remove the serial sticker for the warranty service. 3

4 1. NOTICES Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product or their local government office for details of where and how to safely recycle the item. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER(OR BACK). NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient mangnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance(servicing) instruction in the literature accompanying the appliance. 4

5 2. FOR YOUR SAFETY 1) All warnings and instructions in this manual should be followed. 2) Save this manual for future reference. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with a dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) To help prevent electric shock, plug the equipment and peripheral power cables into properly polarized or grounded electrical outlets. These cables are equipped with the wide blade or the third prong to ensure proper grounding. Do not use adapter plugs or remove the grounding prong from a cable. If the provided plug does not fit your outlet, consult an electrician. 10) Ensure that nothing rests on your equipment s cables and that the cables are not located where they can be stepped on, tripped over, or pinched. 11) Only use attachments or accessories as specified. 12) Only use the equipment with the cart, stand, tripod, bracket, or table that is specified by the manufacturer or sold with the apparatus. When a cart is used, use caution to prevent the cart from tipping over and to avoid injury. 13) Do not connect or disconnect during lightning storms due to risk of electric shock. 14) If any of the following conditions occur, unplug the equipment from the electrical outlet and replace the part or contact your trained service provider: The power cable, extension cable, or plug is damaged. An object has fallen into the equipment. The equipment has been exposed to water. The equipment has been dropped or damaged. The equipment does not operate correctly when you follow the operating instructions. 5

6 3. FEATURES High resolution SONY 1/2.8" 2.1MP Progressive Color CMOS Image Sensor, Support various digital video output / / / AHD(Analog HD) Output AHD is suitable for long reach transmission over single coaxial cable. Transmission Distance: 300 m (Color) Max. Transmission Distance: 500 m OSD menu for setup and configuration. Provides True Day/Night capability with motorized IR cut filter. Power source: 12VDC / 24VAC/12VDC. UTC (Up the coax.) via AHD coaxial cable. 6

7 4. COMPONENTS DSP COLOR CAMERa c-mount adaptor ring operation manual 7

8 5. OVERVIEW AND FUNCTION FRONT TRIPOD MOUNTING HOLE(1/4"-20 UNC) C-MOUNT ADAPTOR RING LENS MOUNT COVER BACK CS-MOUNT ADAPTOR RING CS-MOUNT ADAPTOR RING LOCKING SCREW(2EA) AUTO IRIS JACK TRIPOD MOUNTING HOLE(1/4"-20 UNC) AHD MENU/SET AHD POWER DC12V/AC24V AC24V / DC12V MENU BUTTON UP BUTTON DOWN BUTTON LEFT BUTTON RIGHT BUTTON POWER LED (The LED turns on when power is supplied) AHD OUTPUT JACK POWER TERMINAL (Used to connect an DC12V power source) (Options: AC24V / DC12V) 8

9 6. INSTALLATION 4. Replace the auto iris lens connection plug cover and take off the Sensor protection cap. Then, attach the auto iris lens to the camera by screwing it in clockwise. 5. Insert the connection plug that is connected to the auto iris lens cable into the auto iris lens connector, located on the side of the camera. * NOTE Use only lenses within the specifications shown below. Otherwise, lenses may damage the camera or abnormal fixing may result. C-mount lens : 10 mm or less CS-mount lens : 5 mm or less 9

10 6. INSTALLATION Installation of C-Mount Lenses CS-MOUNT ADAPTOR RING C-MOUNT ADAPTOR RING Installation of CS-Mount Lens CS-MOUNT ADAPTOR RING 10

11 7. CONNECTION MONITOR CONNECTION - 12VDC AHD AHD OUTPUT AHD AHD DVR AHD OUTPUT CVBS OUT (Service Video) 12VDC REGULATED POWER SUPPLY - 24VAC/12VDC AHD AHD OUTPUT AHD AHD DVR AHD OUTPUT CVBS OUT (Service Video) 24VAC/12VDC REGULATED POWER SUPPLY 11

12 8. DIMENSIONS Unit(mm) 1/4"-20 UNC

13 9. SPECIFICATIONS Imaging Device Effective Pixels Unit cell size 1/2.8" Progressive Scan Sony CMOS 1984(H) x 1105(V) 2.8um (H) x 2.8um (V) Video Output Mode AHD : 1080P 30fps(25fps) / 720p@30fps(25fps) TV Out : CVBS NTSC/PAL Transmission Distance AHD : Color 300m@RG59, BW 500m@RG59 Minimum Illumination 0.5 Lux (F1.6, ICR Off, DSS Off) Auto / Manual selectable Shutter speed 1/30(25), 1/60(50), FLK, 1/240(200), 1/480(400), 1/1000, 1/2000, 1/5000, 1/10000, 1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30 Day/Night True D/N with ICR Mechanism BLC OFF/ BLC/ HSBLC AGC 0 ~ 15 2/ 3DNR OFF / LOW / MIDDLE / HIGH Digital WDR OFF/ ON(LEVEL)/ AUTO SENS-UP OFF/ AUTO(X2, X4, X6, X8, X10, X15, X20, X25, X30) Privacy Masking 4 Zones Motion Detection 4 Zones White Balance AWB/ATW/ PUSH LOCK/ INDOOR/ OUTDOOR/ MANUAL Lens C/CS Mount Lens OSD Language ETC Tact Switch, Coaxial communication(pelco-c) English, Korean, Japanese, Chinese, Russian, French, Spanish, Italian, Portuguese, Dutch, German, Polish, Turkish, Hebrew, Arabic FLIP(H/V/HV), Defog, FREEZE, SHARPNESS, LSC Power Source 12VDC / Dual (24VAC/12VDC) Power DC 12VDC (±10%) Max. 130 ma Consumption Dual 24VAC (±10%) Max. 2.8 W, 12VDC (±10%) Max. 190 ma Operating Temperature -10 C ~ 50 C (14 F ~ 122 F) Storage Temperature -20 C ~ 60 C (-4 F ~ 140 F) Dimension (mm) 58 x 58 x Weight Approx. 220 g *Specifications and designs are subject to change for improving the functionality of this product without notice. 13

14 10. OSD MENU STRUCTURE Menu structure Main 1st Sub Menu 2nd Sub Menu Value LENS EXPOSURE BACKLIGHT WHITE BALANCE DAY&NIGHT NR INDOOR/ OUTDOOR(MIN SHU, MODE DC MAX SHU) IRIS SPEED 0~15 AUTO, 1/30(25), 1/60(50), FLK, 1/240(200), 1/480(400), 1/1000, SHUTTER 1/2000, 1/5000, 1/10000, 1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30 AGC 0 ~ 15 OFF/ AUTO(X2, X4, X6, X8, X10, SENS-UP X15, X20, X25, X30) BRIGHTNESS 1~ 100 D-WDR OFF/ ON(LEVEL)/ AUTO OFF/ AUTO(POS/SIZE, DEFOG GRADATION, DEFAULT) OFF LEVEL LOW/ MIDDLE/ HIGH BLC AREA POSITION, SIZE DEFAULT SELECT AREA1/ AREA2/ AREA3/ AREA4 DISPLAY OFF/ ON(POSITION, SIZE) BLACK MASK OFF/ ON HSBLC LEVEL 0~100 MODE ALL DAY/ NIGHT(AGC LEVEL) DEFAULT AWB ATW AWC(PUSH) INDOOR OUTDOOR BLUE 0~100 MANUAL RED 0~100 D N(AGC) 0~255 D N(DELAY) 0~ 60sec, 1sec/step AUTO N D(AGC) 0~255 N D(DELAY) 0~ 60sec, 1sec/step COLOR BURST OFF/ ON B/W IR SMART OFF/ ON D N(DELAY) 1 ~ 60sec, 1sec/step EXT N D(DELAY) 1 ~ 60sec, 1sec/step 2DNR OFF/ LOW/ MIDDLE/ HIGH 3DNR OFF/ LOW/ MIDDLE/ HIGH 14

15 10. OSD MENU STRUCTURE Main 1st Sub Menu 2nd Sub Menu Value CAM TITLE OFF ON 0~9, A~Z, Special Character FREEZE OFF/ ON D-EFFECT MIRROR OFF/MIRROR/ V-FLIP/ ROTATE NEG. IMAGE OFF/ ON SELECT AREA1/ AREA2/ AREA3/ AREA4 DISPLAY OFF/ ON(POSITION, SIZE) SENSITIVITY 0~100 COLOR WHITE/ RED/ GREEN/ BLUE MOTION TRANS 0.00/ 0.25/ 0.75/ 1.0 ALARM VIEW TYPE/ OSD VIEW/ ALARM OUT/ TIME DEFAULT SELECT AREA1/ AREA2/ AREA3/ AREA4 DISPLAY OFF/ MOSAIC/ INV/ COLOR SPECIAL COLOR WHITE/ BLACK/ RED/ BLUE/ PRIVACY YELLOW/ GREEN/ CYAN/ USER TRANS 0.25/ 0.50/ 0.75/ 1.0 DEFAULT LANGUAGE ENG/ CHN/ CHN(S)/ GER/ FRA/ ITA/ SPA/ POL/ RUS/ POR/ NED/ TUR/ KOR/ JPN/ HEB/ ARB LIVE DPC OFF/ ON(AGC LEVEL / LEVEL) WHITE DPC POS/SIZE, START, DPC DEFECT VIEW,LEVEL, AGC, SENS-UP BLACK DPC POS/SIZE, START, DPC VIEW,LEVEL CAM ID 0~255 ID DISPLAY OFF/ ON RS485 BAUDRATE 2400/ 4800/ 9600/ 19200/ LEVEL 0~10 SHARPNESS START AGC 0~255 END AGC 0~255 LCD GAMMA/ BLUE GAIN/ RED GAIN MONITOR ADJUST CRT BLUE GAIN/ RED GAIN LSC OFF/ ON VIDEO.OUT NTSC/ PAL OUTPUT_SIZE 1080P 720P EXIT SAVE&END/ RESET/ NOT SAVE * VIDEO output & VIDEO_EXT signal Press Left key more than 5sec. : 960H Press Right key more than 5sec. : AHD (default mode) * HD Resolution Press up key more then 5 sec : 720p * Signal Format Press Down key more than 5 sec : NTSC 1080p (Default mode) PAL (The initial value is set at Default.) * Changing the ADJUST / VIDEO OUT from the default settings may cause the VIDEO BLACKOUT. (In case of setting "Adjust/VIDEO OUT" mode in the menu, it may cause "VIDEO Black out" in DVR. For the settlement, the "VIDEO OUT" setting should be set compatible with the camera. * Reset of camera will make initial value as factory reset.) * DAY&NIGHT / EXT function is NOT operable. * SPECIAL / RS485 NOT operable. * SPECIAL / MOTION / ALARM / ALARM OUT, TIME function is NOT operable. 15

16 11. AHD UTC (UP THE COAX) The UTC function supports OSD control via AHD coaxial cable. Important) * When low quality coaxial cable is used, it may not be possible to control OSD menu. 16