VISTA ZOOM Infra Red Illuminator Instructions

Transcription

1 VISTA ZOOM Infra Red Illuminator Instructions This manual will detail the installation and set up required to get the best performance from your VISTA Zoom Infra-Red LED illuminator Contents 1. Back of unit & Wiring Page 2 2. Adjusting the beam angle Page 3 3. Mounting and Set-up Page 4 4. Specifications Page 5 5. Dimensions Page 6 6. Troubleshooting Page 7 VISTA Zoom Installation Guide 1

2 1. Back of Unit Photocell Input Cable 12-24V AC/DC Wiring Standard Lamp cable mm DC AC Black wire - ~ Red wire + ~ 1.5m Install in a well ventilated area Do not continually stare at lamp 2 VISTA Zoom Installation Guide

3 2. Adjusting the beam angle Alter angle of illumination (Optional) The angle of illumination can be adjusted using the Zoom Adjustment Screw (ZAS) on the front of the illuminator. Using a 4mm hex/allen key, turn the ZAS clockwise to widen the angle of illumination. Turn the ZAS anti-clockwise to narrow the angle of illumination. Please refer to the table below to set your required angle of illumination. Please note: The default setting for the Zoom illuminator will be 90 Angle (FWHM) Achievable Distance (m)* No. Turns Zoom Adjustment Screw Using a 4mm Hex/Allen key Clockwise = Widens illumination Counterclockwise = Narrows illumination *Subject to camera performance VISTA Zoom Installation Guide 3

4 3. Mounting and Set-up 1 Position illuminator adjacent to camera and point towards scene (Optional night set-up for optimum image performance) 2 Adjust vertical and horizontal position of lamp to ensure full field of view illuminated TARGET 3 Tighten all fixings 4 Connect Illuminator to low voltage power supply: Installers can extend or reduce lead length using appropriate cable and weather proof box. Power the unit using 12-24V AC/DC Optional Bracketry Wall Mount Ptz Mount Dome Mount Pole Mount 4 VISTA Zoom Installation Guide

5 4. Specifications VISTA Zoom Wavelength 850nm Infra-Red Max Distance 100m* (see Page 3 for full distances) Angles available 3.5 to 90 Consumption 5W max Input 12-24V AC/DC Current (DC only) 12V: 0.37A 24V: 0.21A Environment IP66 Temp Range -30 to +50 C Weight 0.85kg (1.9lbs) Dimensions L x W x D 124 x 90 x 176mm (4.8 x 3.5 x 7 ) Integrated Control Features Built-in photocell for automatic on/off operation VISTA Zoom Installation Guide 5

6 5. Dimensions 176.1mm 90.6mm 123.5mm 93.4mm Front Rear 6 VISTA Zoom Installation Guide

7 6. Troubleshoot Ensure all tests are undertaken by a qualified, trained engineer. Ensure safe working practices are followed at all times. Step 1: Basics Ensure power is 12-24V AC/DC Check photocell is working-cover photocell, light should turn on. Ensure power supply is suitably rated to product - check page 5 for specifications If longer cables used, ensure sufficient voltage is provided to allow for voltage drops across the cable If OK Step 2: Lamp Test Check current draw of lamp corresponds to specification on page 5 To check lamp current remove +ve (red) lead from external power source and connect multimeter (set to 10A) in line with the lamp. [One lead of multimeter in common (COM), other lead into 10A socket of multimeter; set multimeter to read Amps]. For correct current draw, see page 5. Step 3: Set-up Camera, lens and illumination Check alignment of lamp and angle selected Check camera lens fully open at night & set correctly Check performance specification of illuminator with camera and lens to ensure required distance is achievable Step 4: Call VISTA for further assistance Note down: Model and serial number of illuminator Camera make and model Lens make and model If the Vista lamp is still not delivering the required performance, please contact us for further assistance: Vista, 210 Wharfedale Road, Winnersh Triangle, Workingham, Berkshire, UK, RG41 5TP Tel: +44 (0) Fax: +44 (0) VISTA Zoom Installation Guide 7

8 Vista, 210 Wharfedale Road, Winnersh Triangle, Workingham, Berkshire RG41 5TP Tel: +44 (0) Fax: +44 (0)