Kellogg Square LIGHT FIXTURE CUT SHEETS. November 4, 2013

Transcription

1

2 Kellogg Square LIGHT FIXTURE CUT SHEETS November 4, West Alamar Ave. Suite C Santa Barbara, CA telephone (805) fax (805)

3

4

5 Job: Type: Notes: PREFIX S1 Page 1 of 7 Philips Gardco PureForm luminaires combine LED performance excellence and advanced Gardco LED thermal management technology with a distinct purity of style to provide outdoor area lighting that is both energy efficient and aesthetically pleasing. PureForm is defined by its high performance, sleek low profile design and rugged construction. The die cast aluminum housing mounts directly to a pole or wall, and has a maximum profile of just 3". The advanced LED optical systems provide IES Types II, III, IV and V distributions, as well as a Backlight Control optic. Special LEED corner cutoff optics are also available. All LED wattages utilize high performance Class 1 LED systems. The luminaire features a state of the art integral thermal control system to maximize LED performance and life, and to extend component life. The door frame is die cast aluminum. Luminaires are finished with a fade and abrasion resistant TGIC powdercoat. PureForm luminaires are available in a wide variety of mountings and arms. All PureForm luminaires provide full cutoff performance. ARM MOUNTING A1 9" Standard Arm Mount A3 Decorative Arm Mount PureForm LED P32 Area Luminaires OPTICAL SYSTEM LED WATTAGE LED SELECTION VOLTAGE FINISH OPTIONS Enter the order code into the appropriate box above. Note: Philips Gardco reserves the right to refuse a configuration. Not all combinations and configurations are valid. Refer to notes below for exclusions and limitations. For questions or concerns, please consult the factory. A2 5" Short Arm Mount MA Mast Arm Mount PureForm luminaires are provided standard without a glass lens, for maximized performance. A glass lens is available as an option, resulting in reduced performance. P32MR50 A LA NW UNIV BRP PREFIX (See page 4 and page 5 for details on luminaire configurations.) P32 32" PureForm Luminaire Constant Wattage P32DCC 32" PureForm Luminaire Dual Circuit Control P32DIM 32" PureForm with 010V Dimming P32MR " PureForm with Motion Response 50% Low, Pole Mounted Motion Sensor P32APD 2 32" PureForm with Automatic Profile Dimming P32APDMRO 1 32" PureForm APD with Motion Response Override, Pole Mounted Motion Sensor 1. MR50 and APDMRO luminaires require one motion sensor per pole, ordered separately. See Accessories on page 2. Motion Response luminaires available 120V or 277V only. 2. Available 120V through 277V only. ARM (Omit for Mast Arm Mount luminaires) Arm Style Available Mountings A1 Standard 9" Arm Direct to Pole Mount and Wall Mount A2 Short 5" Arm Direct to Pole Mount and Wall Mount A3 Decorative Arm Direct to Pole Mount Only Note: All Arm Styles shown above mount to a round pole with no adapter. If mounting to a square pole, specify the appropriate Square Pole Adapter option: SPA12 for A1 or A2 arms, SPA3 for A3 arms. See Options on page 2. MOUNTING Direct to Pole Mount (Available with A1, A2 or A3 Arms) 1 Single Pole Mount 2 Twin Pole Mount at 180 2@90 Twin Pole Mount at 3 3way Pole Mount at 3@120 3way Pole Mount at way Pole Mount Mast Arm Mount MA Mast Arm Mount (Requires 2 3/8" OD Mast Arm) Wall Mount (Available with A1 or A2 Arms Only. Not available in P32MR50, or P32APDMRO.) W Wall Mount WS Wall Mount, Surface Conduit OPTICAL SYSTEM 4 Featuring unitized optic lens construction. Type Standard Position Rotated Left 5 () Rotated Right 5 (270 ) Type II Type III Type IV Type V Medium 5M Type V Wide 5W Backlight Control BLC BLC90 BLC270 LEED Corner Cutoff s 6 LCL LCR 4. Luminaire door frame and optic assembly provided standard without glass lens. Specify CLR option for clear glass lens. See Options on page See pages 6 and 7 for information on optical rotation prior to ordering. 6. Available with 170LA or 260LA LED wattages only Koninklijke Philips Electronics N.V. All Rights Reserved. G200036/1012

6 Job: Type: Notes: PREFIX S2 Page 1 of 7 Philips Gardco PureForm luminaires combine LED performance excellence and advanced Gardco LED thermal management technology with a distinct purity of style to provide outdoor area lighting that is both energy efficient and aesthetically pleasing. PureForm is defined by its high performance, sleek low profile design and rugged construction. The die cast aluminum housing mounts directly to a pole or wall, and has a maximum profile of just 3". The advanced LED optical systems provide IES Types II, III, IV and V distributions, as well as a Backlight Control optic. Special LEED corner cutoff optics are also available. All LED wattages utilize high performance Class 1 LED systems. The luminaire features a state of the art integral thermal control system to maximize LED performance and life, and to extend component life. The door frame is die cast aluminum. Luminaires are finished with a fade and abrasion resistant TGIC powdercoat. PureForm luminaires are available in a wide variety of mountings and arms. All PureForm luminaires provide full cutoff performance. ARM MOUNTING A1 9" Standard Arm Mount A3 Decorative Arm Mount PureForm LED P32 Area Luminaires OPTICAL SYSTEM LED WATTAGE LED SELECTION VOLTAGE FINISH OPTIONS Enter the order code into the appropriate box above. Note: Philips Gardco reserves the right to refuse a configuration. Not all combinations and configurations are valid. Refer to notes below for exclusions and limitations. For questions or concerns, please consult the factory. A2 5" Short Arm Mount MA Mast Arm Mount PureForm luminaires are provided standard without a glass lens, for maximized performance. A glass lens is available as an option, resulting in reduced performance. P32MR50 A LA NW UNIV BRP PREFIX (See page 4 and page 5 for details on luminaire configurations.) P32 32" PureForm Luminaire Constant Wattage P32DCC 32" PureForm Luminaire Dual Circuit Control P32DIM 32" PureForm with 010V Dimming P32MR " PureForm with Motion Response 50% Low, Pole Mounted Motion Sensor P32APD 2 32" PureForm with Automatic Profile Dimming P32APDMRO 1 32" PureForm APD with Motion Response Override, Pole Mounted Motion Sensor 1. MR50 and APDMRO luminaires require one motion sensor per pole, ordered separately. See Accessories on page 2. Motion Response luminaires available 120V or 277V only. 2. Available 120V through 277V only. ARM (Omit for Mast Arm Mount luminaires) Arm Style Available Mountings A1 Standard 9" Arm Direct to Pole Mount and Wall Mount A2 Short 5" Arm Direct to Pole Mount and Wall Mount A3 Decorative Arm Direct to Pole Mount Only Note: All Arm Styles shown above mount to a round pole with no adapter. If mounting to a square pole, specify the appropriate Square Pole Adapter option: SPA12 for A1 or A2 arms, SPA3 for A3 arms. See Options on page 2. MOUNTING Direct to Pole Mount (Available with A1, A2 or A3 Arms) 1 Single Pole Mount 2 Twin Pole Mount at 180 2@90 Twin Pole Mount at 3 3way Pole Mount at 3@120 3way Pole Mount at way Pole Mount Mast Arm Mount MA Mast Arm Mount (Requires 2 3/8" OD Mast Arm) Wall Mount (Available with A1 or A2 Arms Only. Not available in P32MR50, or P32APDMRO.) W Wall Mount WS Wall Mount, Surface Conduit OPTICAL SYSTEM 4 Featuring unitized optic lens construction. Type Standard Position Rotated Left 5 () Rotated Right 5 (270 ) Type II Type III Type IV Type V Medium 5M Type V Wide 5W Backlight Control BLC BLC90 BLC270 LEED Corner Cutoff s 6 LCL LCR 4. Luminaire door frame and optic assembly provided standard without glass lens. Specify CLR option for clear glass lens. See Options on page See pages 6 and 7 for information on optical rotation prior to ordering. 6. Available with 170LA or 260LA LED wattages only Koninklijke Philips Electronics N.V. All Rights Reserved. G200036/1012

7 Job: Type: Notes: PREFIX S3 Page 1 of 7 Philips Gardco PureForm luminaires combine LED performance excellence and advanced Gardco LED thermal management technology with a distinct purity of style to provide outdoor area lighting that is both energy efficient and aesthetically pleasing. PureForm is defined by its high performance, sleek low profile design and rugged construction. The die cast aluminum housing mounts directly to a pole or wall, and has a maximum profile of just 3". The advanced LED optical systems provide IES Types II, III, IV and V distributions, as well as a Backlight Control optic. Special LEED corner cutoff optics are also available. All LED wattages utilize high performance Class 1 LED systems. The luminaire features a state of the art integral thermal control system to maximize LED performance and life, and to extend component life. The door frame is die cast aluminum. Luminaires are finished with a fade and abrasion resistant TGIC powdercoat. PureForm luminaires are available in a wide variety of mountings and arms. All PureForm luminaires provide full cutoff performance. ARM MOUNTING A1 9" Standard Arm Mount A3 Decorative Arm Mount PureForm LED P32 Area Luminaires OPTICAL SYSTEM LED WATTAGE LED SELECTION VOLTAGE FINISH OPTIONS Enter the order code into the appropriate box above. Note: Philips Gardco reserves the right to refuse a configuration. Not all combinations and configurations are valid. Refer to notes below for exclusions and limitations. For questions or concerns, please consult the factory. A2 5" Short Arm Mount MA Mast Arm Mount PureForm luminaires are provided standard without a glass lens, for maximized performance. A glass lens is available as an option, resulting in reduced performance. P32MR50 A3 1 5W 160LA NW UNIV BRP PREFIX (See page 4 and page 5 for details on luminaire configurations.) P32 32" PureForm Luminaire Constant Wattage P32DCC 32" PureForm Luminaire Dual Circuit Control P32DIM 32" PureForm with 010V Dimming P32MR " PureForm with Motion Response 50% Low, Pole Mounted Motion Sensor P32APD 2 32" PureForm with Automatic Profile Dimming P32APDMRO 1 32" PureForm APD with Motion Response Override, Pole Mounted Motion Sensor 1. MR50 and APDMRO luminaires require one motion sensor per pole, ordered separately. See Accessories on page 2. Motion Response luminaires available 120V or 277V only. 2. Available 120V through 277V only. ARM (Omit for Mast Arm Mount luminaires) Arm Style Available Mountings A1 Standard 9" Arm Direct to Pole Mount and Wall Mount A2 Short 5" Arm Direct to Pole Mount and Wall Mount A3 Decorative Arm Direct to Pole Mount Only Note: All Arm Styles shown above mount to a round pole with no adapter. If mounting to a square pole, specify the appropriate Square Pole Adapter option: SPA12 for A1 or A2 arms, SPA3 for A3 arms. See Options on page 2. MOUNTING Direct to Pole Mount (Available with A1, A2 or A3 Arms) 1 Single Pole Mount 2 Twin Pole Mount at 180 2@90 Twin Pole Mount at 3 3way Pole Mount at 3@120 3way Pole Mount at way Pole Mount Mast Arm Mount MA Mast Arm Mount (Requires 2 3/8" OD Mast Arm) Wall Mount (Available with A1 or A2 Arms Only. Not available in P32MR50, or P32APDMRO.) W Wall Mount WS Wall Mount, Surface Conduit OPTICAL SYSTEM 4 Featuring unitized optic lens construction. Type Standard Position Rotated Left 5 () Rotated Right 5 (270 ) Type II Type III Type IV Type V Medium 5M Type V Wide 5W Backlight Control BLC BLC90 BLC270 LEED Corner Cutoff s 6 LCL LCR 4. Luminaire door frame and optic assembly provided standard without glass lens. Specify CLR option for clear glass lens. See Options on page See pages 6 and 7 for information on optical rotation prior to ordering. 6. Available with 170LA or 260LA LED wattages only Koninklijke Philips Electronics N.V. All Rights Reserved. G200036/1012

8 Job: Type: Notes: PREFIX S4 Page 1 of 7 Philips Gardco PureForm luminaires combine LED performance excellence and advanced Gardco LED thermal management technology with a distinct purity of style to provide outdoor area lighting that is both energy efficient and aesthetically pleasing. PureForm is defined by its high performance, sleek low profile design and rugged construction. The die cast aluminum housing mounts directly to a pole or wall, and has a maximum profile of just 3". The advanced LED optical systems provide IES Types II, III, IV and V distributions, as well as a Backlight Control optic. Special LEED corner cutoff optics are also available. All LED wattages utilize high performance Class 1 LED systems. The luminaire features a state of the art integral thermal control system to maximize LED performance and life, and to extend component life. The door frame is die cast aluminum. Luminaires are finished with a fade and abrasion resistant TGIC powdercoat. PureForm luminaires are available in a wide variety of mountings and arms. All PureForm luminaires provide full cutoff performance. ARM MOUNTING A1 9" Standard Arm Mount A3 Decorative Arm Mount PureForm LED P32 Area Luminaires OPTICAL SYSTEM LED WATTAGE LED SELECTION VOLTAGE FINISH OPTIONS Enter the order code into the appropriate box above. Note: Philips Gardco reserves the right to refuse a configuration. Not all combinations and configurations are valid. Refer to notes below for exclusions and limitations. For questions or concerns, please consult the factory. A2 5" Short Arm Mount MA Mast Arm Mount PureForm luminaires are provided standard without a glass lens, for maximized performance. A glass lens is available as an option, resulting in reduced performance. P32MR50 A3 2 5W 160LA NW UNIV BRP PREFIX (See page 4 and page 5 for details on luminaire configurations.) P32 32" PureForm Luminaire Constant Wattage P32DCC 32" PureForm Luminaire Dual Circuit Control P32DIM 32" PureForm with 010V Dimming P32MR " PureForm with Motion Response 50% Low, Pole Mounted Motion Sensor P32APD 2 32" PureForm with Automatic Profile Dimming P32APDMRO 1 32" PureForm APD with Motion Response Override, Pole Mounted Motion Sensor 1. MR50 and APDMRO luminaires require one motion sensor per pole, ordered separately. See Accessories on page 2. Motion Response luminaires available 120V or 277V only. 2. Available 120V through 277V only. ARM (Omit for Mast Arm Mount luminaires) Arm Style Available Mountings A1 Standard 9" Arm Direct to Pole Mount and Wall Mount A2 Short 5" Arm Direct to Pole Mount and Wall Mount A3 Decorative Arm Direct to Pole Mount Only Note: All Arm Styles shown above mount to a round pole with no adapter. If mounting to a square pole, specify the appropriate Square Pole Adapter option: SPA12 for A1 or A2 arms, SPA3 for A3 arms. See Options on page 2. MOUNTING Direct to Pole Mount (Available with A1, A2 or A3 Arms) 1 Single Pole Mount 2 Twin Pole Mount at 180 2@90 Twin Pole Mount at 3 3way Pole Mount at 3@120 3way Pole Mount at way Pole Mount Mast Arm Mount MA Mast Arm Mount (Requires 2 3/8" OD Mast Arm) Wall Mount (Available with A1 or A2 Arms Only. Not available in P32MR50, or P32APDMRO.) W Wall Mount WS Wall Mount, Surface Conduit OPTICAL SYSTEM 4 Featuring unitized optic lens construction. Type Standard Position Rotated Left 5 () Rotated Right 5 (270 ) Type II Type III Type IV Type V Medium 5M Type V Wide 5W Backlight Control BLC BLC90 BLC270 LEED Corner Cutoff s 6 LCL LCR 4. Luminaire door frame and optic assembly provided standard without glass lens. Specify CLR option for clear glass lens. See Options on page See pages 6 and 7 for information on optical rotation prior to ordering. 6. Available with 170LA or 260LA LED wattages only Koninklijke Philips Electronics N.V. All Rights Reserved. G200036/1012

9 Page 2 of 7 LED WATTAGE AND LUMEN VALUES Ordering Code Average System Watts 7 LED Current (ma) LED Quantity Dual LED Array Per LED Array Total LEDs LED Selection PureForm LED P32 Area Luminaires Luminaire Initial Absolute Lumens 8,9 TYPE 2 TYPE 3 TYPE 4 TYPE 5M TYPE 5W 110LA NW 8,997 (s) 9,340 (s) 8,687 10,286 (s) 10,901(s) 140LA NW 11,947 (s) 12,380 (s) 11,599 (s) 13,659 (s) 14,475 (s) 170LA NW 14,749 15,204 (s) 14,320 16,863 17, LA NW 12,423 (s) 13,249 (s) 12,263 14,400 (s) 15, LA NW 16,496 (s) 17,593 (s) 16,330 (s) 19,122 (s) 20, LA NW 20,366 21,720 20,161 23,607 25, Wattage may vary by +/ 8% due to LED manufacturer forward volt specification and ambient temperature. Wattage shown is average for 120V through 277V input. Actual wattage may vary by an additional +/ 10% due to actual input voltage. 8. Values shown are for luminaires without the CLR, DL or EHHS options. Tests are in process for configurations not shown. (s) following the value indicates that values are scaled from tests on similar, but not identical luminaire configurations. Contact Gardco.applications@ philips.com if any approximate estimates are required for design purposes. 9. Lumen values based on tests performed in compliance with IESNA LM79. LED SELECTION CW Cool White 5700 K 75 CRI Nominal NW Neutral White 4000 K 70 CRI Nominal WW Warm White 3000 K 80 CRI Nominal VOLTAGE UNIV 120V through 277V, 50hz or 60hz HVU 347V through 480V, 50hz or 60hz (High Voltage Universal) FINISH BRP Bronze Paint BLP Black Paint WP White Paint NP Natural Aluminum Paint OC Optional Color Paint Specify Optional Color or RAL ex: OCLGP or OCRAL7024. SC Special Paint Specify. Must supply color chip. OPTIONS F 10 Fusing DL LF InLine/InPole Fusing CLR BD 11 Bird Deterrent Spike Kit POLY 15 PC 12,13,14 Photocontrol and Receptacle SPR 16 PCR 13,14 Photocontrol Receptacle only PCB 12,13,14 Button Photocontrol SPRH 16 EHHS External Houseside Shield PTF2 Pole Top Fitter 2 3/8" 3" Dia. Tenon TB PTF3 Pole Top Fitter 3" 3 1/2" Dia. Tenon TL PTF4 Pole Top Fitter 3 1/2" 4" Dia. Tenon SPA12 Square Pole Adapter (for use with A1 or A2 Arms) SPA3 Square Pole Adapter (for use with A3 Arms) Diffusing Lens (reduces performance significantly) Clear Glass Lens (reduces performance) Polycarbonate Lens (reduces performance) Surge Protection for 120V through 277V Input meeting ANSI C Surge Protection for 347V through 480V Input meeting ANSI C Terminal Block Provides for access to the LED arrays and driver without tools ACCESSORIES (Ordered separately) MSP MSA120V MSA277V 10. Available with A1 arm or with MA mounting only. Provide specific input voltage. 11. Kits consist of 25 injection molded plastic bird deterrent spikes. Field installation only. 12. Not available in 480V. Provide specific input voltage. 13. Available with A1 or A2 arms, or with MA mounting only. 14. Not available in P32DCC. 15. Polycarbonate lenses feature a 1 year warranty only. 16. Not available with Fusing (F) option. 120V or 277V Input Pedestrian Motion Sensor for P32MR50 (Motion Response) or P32APDMRO (Automatic Profile Dimming with Motion Response Override) 120V Input Area Motion Sensor for P32MR50 (Motion Response) or P32APDMRO (Automatic Profile Dimming with Motion Response Override) 277V Input Area Motion Sensor for P32MR50 (Motion Response) or P32APDMRO (Automatic Profile Dimming with Motion Response Override) Motion Sensors are ordered separately, with one (1) motion sensor required per pole location for P32MR50 or P32APDMRO luminaires. See Luminaire Configuration Information on page 45 for more details. Pedestrian sensor color is white. Area motion sensor color is Arctic White Koninklijke Philips Electronics N.V. All Rights Reserved. G200036/1012

10 Page 3 of 7 PureForm LED P32 Area Luminaires DIMENSIONS AND EPA A1 STANDARD ARM MOUNT A2 SHORT ARM MOUNT MA MAST ARM MOUNT A A = 6.53" cm Maximum Profile (All Models) = 3.0" / 7.62 cm C C = 5.73" cm D D = 3.68" cm B = 9.21" cm B 40.53" / cm 5.1" / cm 36.43"/ cm E = 10.25" cm E 41.58"/ cm A 20.3" / cm A = 6.53" cm 20.3" / cm C C = 5.73" cm 20.3" cm D D = 3.68" cm A3 DECORATIVE ARM MOUNT WITH A1 STANDARD ARM WALL MOUNT F F = 10.06" cm 20.3" / cm F = 10.06" cm F G H G = 7.25" cm H = 11.29" cm 42.62" / cm WITH A2 SHORT ARM 17.41" cm 48.74" / cm Single Luminaire Weight K L K = 7.25" cm L= 7.18" cm 38.51" / cm Mounting Approximate Weight Effective Projected Area ft 2 / m 2 A1 57 lbs / kg Mounting Single 180 3/4 A2 56 lbs / kg A / / / A lbs / kg A / / / MA 57 lbs / kg A / / / W or WS 58 lbs / kg MA 0.40 / N/A N/A 2012 Koninklijke Philips Electronics N.V. All Rights Reserved. G200036/1012

11 Page 4 of 7 LUMINAIRE CONFIGURATION INFORMATION (CONTINUED ON PAGE 5) P32: Philips Gardco PureForm LED standard luminaire providing constant wattage and constant light output when power to the luminaire is energized. P32DCC: Philips Gardco PureForm luminaires provided with dual circuiting, permitting separate switching of each led array. P32DIM: Philips Gardco PureForm LED luminaire provided with 0 10V dimming for connection to a control system provided by others. PureForm LED P32 Area Luminaires The pedestrian motion detector provides coverage equal to the sensor height above ground, in all directions from the sensor (360.) For longer range detection applications, The area motion sensor is recommended. Side Coverage Pattern Top Coverage Pattern P32MR50: Philips Gardco PureForm LED luminaire with motion response, providing a 50% power reduction on low and a commensurate reduction in light output. The power and light output reduction is accomplished utilizing the Philips DynaDimmer module, programmed for a constant 50% power. Power supplied by the motion sensor connected to the override line on the DynaDimmer takes the luminaire to high setting, 100% power and light output, when motion is detected. The luminaire remains on high until no motion is detected for the motion sensor duration period, after which the luminaire returns to low. Duration period is factory set at 15 minutes, and is field adjustable from 5 minutes up to 15 minutes. This configuration is not available for use with wall mounted luminaires. P32MR50 is available in 120V through 277V input only to the luminaire. Motion sensors require single voltage 120V or 277V input. The Area PIR motion sensor is the WattStopper EW200120W (120V Input MSA120V) or the WattStopper EW200277W (277V Input MSA277V.) One motion sensor per pole is required and is ordered separately. Area sensors require single voltage 120V or 277V input. 2H 1H Distances are approximate. H = Height above ground. Motion response requires that the pole include an additional hand hole 15 feet above the pole base, normally oriented 180 to the standard hand hole. For Philips Gardco poles, order the pole with the Motion Sensor Mounting (MSM) option which includes the hand hole and a special hand hole cover plate for the sensor with a 1/2" NPT receptacle centered on the hand hole cover plate into which the motion sensor mounts. Once the motion sensor is connected to the hand hole cover plate, then wiring connections are completed in the pole. The plate (complete with motion sensor attached and wired) is then mounted to the hand hole. If poles are supplied by others, the customer is responsible for providing suitable mounting accommodations for the motion sensor in the pole. 2H Mounting to a Philips Gardco Pole Black, 120V OR 277V Input White Neutral Sensor Red Connects to Override Input (Orange) Line of DynaDimmer The area motion detector provides coverage equal to up to 6 times the sensor height above ground, 270 from the frontcenter of the sensor. Wiring in Pole Cover Plate with 1/2" NPT Coupling (supplied with pole) Motion Sensor Additional Hand Hole 15' Above Pole Base (oriented 180 to the standard hand hole) Attach Motion Sensor to Cover Plate coupling, Complete Wiring in Pole and Attach Cover Plate to Hand Hole Area PIR Motion Sensor Coverage Pattern: Neutral 120V OR 277V power input Sensor Black Height 270 Front Coverage Distances are approximate. H= Height Above Ground 8ft (2.4m) 9.5ft (3m) 1H White 25ft (8m) 3H Red 52.5ft (16m) The Pedestrian PIR motion sensor is the WattStopper HB350WL3. One motion sensor per pole is required and is ordered separately as the MSP accessory, see page 2. The Pedestrian sensor accept 120V or 277V input. 6H Red Connects to Override Input (Orange) Line of DynaDimmer P32APD: Philips Gardco PureForm LED luminaire with Automatic Profile Dimming. Luminaire is provided with a programmable LED Driver. The programmable LED Driver is programmed to go to 50% power, 50% light output two (2) hours prior to night time midpoint and remain at 50% for six (6) hours after night time midpoint. Midpoint is continuously recalculated by the programmable LED Driver based on the average midpoint of the last two full night cycles. Short duration cycles, and power interruptions are ignored and do not affect the determination of midpoint. P32APD is available in 120V through 277V input only. P32APD Dimming Profile: 100% 100% 50% 50% Power On 2 Hours 6 Hours Mid Point Power Off The P32APD offers many of the advantages of a sophisticated control system, including an average energy savings of at least 33% versus constant wattage, constant light output systems, without the need for a control system Koninklijke Philips Electronics N.V. All Rights Reserved. G200036/1012

12 Page 5 of 7 LUMINAIRE CONFIGURATION INFORMATION (CONTINUED FROM PAGE 4) P32APDMRO: Philips Gardco PureForm LED luminaire with Automatic Profile Dimming, with Motion Response Override. The P32APDMRO combines the benefits of both automatic profile dimming and motion response, using the Philips DynaDimmer module. The luminaire will dim to 50% power, 50% light output, per the dimming profile shown for the P32APD. If motion is detected during the time that the luminaire is operating at 50%, the luminaire returns to 100% power and light output. The luminaire remains on high until no motion is detected for the duration period, after which the luminaire returns to low. Duration period is factory set at 15 minutes, and is field adjustable from 5 minutes up to 15 minutes. This configuration is not available for use with wall mounted luminaires. PureForm LED P32 Area Luminaires P32APDMRO is available in 120V through 277V input only to luminaire. The motion sensor requires either 120V or 277V input to the motion sensor. The P32APDMRO has the same pole requirements and utilizes the same motion sensors as the P32MR50. The motion sensor mounts and wires identically as well. The P32APDMRO utilizes the identical dimming profile as shown for the P32APD. By combining the benefits of automatic profile dimming and motion response, the P32APDMRO assures maximum energy savings, and insures that adequate light is present if motion is detected. SPECIFICATIONS GENERAL DESCRIPTION: Philips Gardco PureForm luminaires combine LED performance excellence and advanced Gardco LED thermal management technology with a distinct purity of style to provide outdoor area lighting that is both energy efficient and aesthetically pleasing. PureForm is defined by its high performance, sleek low profile design and rugged construction. The die cast aluminum housing mounts directly to a pole or wall, and has a maximum profile of just 3". All LED wattages utilize high performance Class 1 LED systems. The luminaire features a state of the art integral thermal control system to maximize LED performance and life, and to extend component life. The door frame is die cast aluminum. Luminaires are finished with a fade and abrasion resistant TGIC powdercoat. PureForm luminaires are available in a wide variety of mountings and arms. HOUSING: The PureForm features a die cast aluminum housing, and mounts directly to a pole or wall. The low profile rounded form reduces the effective projected area of the luminaire significantly. PureForm luminaires supplied with A1, A2 and A3 arms are provided with arms firmly attached to the main luminaire housing body. As a result, the luminaires provide the functionality, strength and installation ease of an integral arm luminaire. Mast arm mount luminaires are provided with the mast arm mounting assembly firmly attached to the main luminaire housing body. IP RATING: PureForm luminaires have a rating of IP66. VIBRATION RESISTANCE: PureForm carries a 3G vibration rating that conforms to standards set forth by ANSI C Testing includes vibration to 3G acceleration in three axes, all performed on the same luminaire. OPTICAL SYSTEMS: The advanced LED optical systems provide IES Types II, III, IV and V distributions, as well as a Backlight Control optic. Special LEED corner cutoff optics are also available, both as LCR (right) and LCL (left.) All optical systems feature unitized lens optic construction. Types 2, 3, 4, BLC and LCR/LCL optical systems utilize an innovative redirecting reflector system to complement the performance of the LED optic. The redirecting reflector system includes a black surrounding surface to minimize aperture brightness when viewed from the rear of the luminaire. PureForm luminaires are provided standard without a glass lens, for maximized performance. A glass lens is available as an option, resulting in reduced performance. All PureForm luminaires provide full cutoff performance. Note: All motion sensors utilized consume 0.0 watts in the off state. LED RELIABILITY: PREDICTED LUMEN DEPRECIATION DATA Ambient Temperature C Driver ma L 70 Hours C 350 ma 240, ma 165, ma 215, C 530 ma 148, Predicted performance derived from LED manufacturer s data and engineering design estimates, based on IESNA LM80 methodology. Actual experience may vary due to field application conditions. L 70 is the predicted time when LED performance depreciates to 70% of initial lumen output. THERMAL MANAGEMENT: The Philips Gardco PureForm LED provides die cast aluminum integral thermal radiation fins to provide the excellent thermal management so critical to long LED system life. ELECTRICAL: Luminaires are equipped with an LED driver that accepts 120V through 277V, or 347V through 480V, 50hz to 60hz, input. Driver output is based on the LED wattage selected. Componenttocomponent wiring within the luminaire will carry no more than 80% of rated current and is listed by UL for use at 600 VAC at 302 F / 150 C or higher. Plug disconnects are listed by UL for use at 600 VAC, 15A or higher. Power factor is not less than 90%. Luminaire consumes 0.0 watts in the off state. All motion sensors utilized consume 0.0 watts in the off state. FINISH: Each standard color luminaire receives a fade and abrasion resistant, electrostatically applied, thermally cured, triglycidal isocyanurate (TGIC) textured polyester powdercoat finish. Standard colors include bronze (BRP), black (BLP), white (WP), and natural aluminum (NP). Consult factory for specs on optional or custom colors. LABELS: All luminaires bear UL or CUL (where applicable) Wet Location labels. WARRANTY: Philips Gardco luminaires feature a 5 year limited warranty. Philips Gardco LED luminaires with LED arrays feature a 5 year limited warranty covering the LED arrays. LED Drivers also carry a 5 year limited warranty. Motion sensors are covered by warranty for 5 years by the motion sensor manufacturer. See Warranty Information on for complete details and exclusions. Polycarbonate lenses carry a 1 year warranty. FULL CUTOFF PERFORMANCE: Full cutoff performance means a luminaire distribution where zero candela intensity occurs at an angle at or above above nadir. Additionally, the candela per 1000 lamp lumens does not numerically exceed 100 (10 percent) at a vertical angle of 80 above nadir. This applies to all lateral angles around the luminaire Koninklijke Philips Electronics N.V. All Rights Reserved. G200036/1012

13 Page 6 of 7 PureForm LED P32 Area Luminaires ASYMMETRIC OPTICAL ORIENTATION INFORMATION (CONTINUED ON PAGE 7) STANDARD OPTIC POSITION: Luminaires ordered with asymmetric optical systems in the standard optic position will have the optical system oriented as shown below: LEFT Side of Pole 180 RIGHT Side of Pole Street Side Curbline House Side Note: The hand hole will normally be located on the pole at the 0 point. OPTIC ROTATED LEFT () OPTIC POSITION: Luminaires ordered with asymmetric optical systems in the OPTIC ROTATED LEFT () optic position will have the optical system oriented as shown below: LEFT Side of Pole 180 RIGHT Side of Pole Street Side Curbline House Side Note: The hand hole will normally be located on the pole at the 0 point Koninklijke Philips Electronics N.V. All Rights Reserved. G200036/1012

14 Page 7 of 7 ASYMMETRIC OPTICAL ORIENTATION INFORMATION (CONTINUED FROM PAGE 6) PureForm LED P32 Area Luminaires OPTIC ROTATED RIGHT (270 ) OPTIC POSITION: Luminaires ordered with asymmetric optical systems in the OPTIC ROTATED RIGHT (270 ) optic position will have the optical system oriented as shown below: LEFT Side of Pole 180 RIGHT Side of Pole Street Side Curbline House Side Note: The hand hole will normally be located on the pole at the 0 point. TWIN LUMINAIRE ASSEMBLIES WITH ROTATED OPTICAL SYSTEMS: Twin luminaire assemblies installed with rotated optical systems are an excellent way to direct light toward the interior of the site (Street Side) without additional equipment. It is important, however, that care be exercised to insure that luminaires are installed in the proper location. LEFT Side of Pole 180 RIGHT Side of Pole Street Side Curbline 270 House Side Luminaires with Rotated Right (270 ) are installed on the LEFT Side of Pole 0 Note: The hand hole location will depend on the drilling configuration ordered for the pole. Luminaires with Rotated Left () are installed on the RIGHT Side of Pole 2011 Koninklijke Philips Electronics N.V. All Rights Reserved. G200036/1012

15 Job: Type: Notes: Page 1 of 4 Poles 4.5" Straight Round Aluminum Cast Base The Philips Gardco RA4.5 straight aluminum pole consists of a onepiece 4.5" round extruded aluminum lighting standard mounted to a cast aluminum base. The poles are finished with either Architectural Class 1 anodizing or electrostatically applied TGIC polyester powdercoat. All poles include anchor bolts, full base cover, hand hole, ground lug and top cap. S1,S2,S3 =D1, S4 = D2 PREFIX BASE HEIGHT DRILLING FINISH OPTIONS RA45 CB 20 BRP Enter the order code into the appropriate box above. Note: Gardco reserves the right to refuse a configuration. Not all combinations and configurations are valid. Refer to notes below for exclusions and limitations. For questions or concerns, please consult the factory. PREFIX RA4.5 BASE CB Fixed Cast Base Hinged Bases are available for this pole size. Please refer to Hinged Base Pole sheet for specifications and dimensions. HEIGHT 10' 12' 15' 18' 20' DRILLING D1 1 Way D2 2 Way D2@90 2 Way at D3 3 Way D3@120 3 Way at 120 D4 4 Way T2 2 3/8" OD Tenon T4 4" OD Tenon FINISH OPTIONS BRP BLP WP NP BRA BLA NA OC SC Bronze Paint Black Paint White Paint Natural Aluminum Paint Bronze Anodized Black Anodized Natural Anodized Optional Color Paint Specify Optional Color or RAL ex: OCLGP or OCRAL7024. Special Color Paint Specify. Must supply color chip. DR GFCI VDA Duplex Receptacle Ground Fault Receptacle Vibration Dampener Nipples and Couplings Indicate size (1/2", 3/4", 1", 1 1/4", 1 1/2". ) Indicate height above base and orientation to hand hole. See Pole Orientataion Information on Page 4. NL Nipple External thread CL Coupling Internal thread Single Mount Bullhorn Brackets Indicate height above base and orientation to hand hole. See Pole Orientation Information on Page 4. A15BH19 Single 1.9" OD A15BH24 Single 2.4" OD A215BH19 2Tenon 1.9" OD A215BH24 2Tenon 2.4" OD Motion Response Provisions GMR Provision for Gardco HID Motion Response System Minimum Pole Height is 18'. Includes a 1/2" coupling placed 180 to the hand hole, 12' above the pole base. MSM Motion Sensor Mounting Provision for LED Luminaires available with Motion Response Minimum Pole Height is 18'. Includes a special hand hole with 1/2" coupling placed in the cover plate, 180 to the hand hole, 15' above the pole base Koninklijke Philips Electronics N.V. All Rights Reserved /0611

16 Page 2 of 4 Poles 4.5" Straight Round Aluminum Cast Base POLE DATA CATALOG NUMBER POLE SIZE MAXIMUM LUMINAIRE LOADING 1 ANCHOR BOLT DATA 2 WALL THICKNESS (inches.) 100 MPH 90 MPH 80 MPH BOLT CIRCLE (inches) PREFIX BASE HEIGHT ACTUAL HEIGHT EPAFT 2 EPAFT 2 EPAFT 2 BOLT SIZE (inches) MAX PROJ. (inches) RA4.5CB10 10' /4 x 17 x " RA4.5CB12 12' /4 x 17 x " RA4.5CB15 15' /4 x 17 x " RA4.5CB18 18' /4 x 17 x " RA4.5CB20 20' /4 x 17 x " 1. Warning: Additional wind loading, in terms of EPA, from banners, cameras, floodlights and other accessories attached to the pole, must be added to the luminaire(s) EPA before selecting the pole with the appropriate wind load capability. 2. Factory supplied template must be used when setting anchor bolts. Philips Gardco will not honor any claim for incorrect anchorage placement resulting from failure to use factory supplied templates. DIMENSIONS CONDUIT Conduit Opening OPENING A Supplied with a Full Base Cover CAST (not ALUMINUM shown) NUT COVER 4.5" 3.25" C Tapped TAPPED 3/8" 3/8"16 for FOR Ground GROUND Connector CONNECTOR 8 3/4" F TAPPED Tapped 3/8" 3/8"16 FOR for Ground GROUND CONNECTOR Connector 4.125" E Bolt Circle MINIMUM B 7" Minimum MAXIMUM Bolt Circle B 8.625" Maximum Anchor Bolt D Length HANDHOLE Hand hole REINFORCEMENT Reinforcement HANDHOLE Hand hole Detail DETAIL NOTE: Factory supplied template MUST be used when setting anchor bolts. Philips Gardco will not honor any claim for incorrect anchorage placement from failure to use factory supplied templates Koninklijke Philips Electronics N.V. All Rights Reserved /0611

17 Page 3 of 4 SPECIFICATIONS All aluminum alloys shall comply with metallurgical and mechanical properties set forth in the Aluminum Association Standards. POLE SHAFT: The shaft shall be extruded from all new seamless 6063 alloy aluminum and shall be heat treated to produce a T6 temper. The shaft shall be polished with fine grain aluminum oxide cloths, resulting in a high quality circumferential satin brushed finish. After finishing, each pole shall be fully tirewrapped with neutral PH krinkle/kraft paper for protection in shipment.. ANCHOR BASE: The anchor base is cast from A356 alloy aluminum. The shaft shall be inserted into the anchor base casting. The anchor base casting and shaft shall be joined by a continuous circumferential weld at the inside bottom of the anchor base. The completed assembly shall be heat treated to a T6 condition. A full base cover shall be included with each anchor base. ANCHOR BOLTS: Anchor bolts are fabricated from a commercial quality hot rolled carbon steel bar that meets or exceeds a minimum guaranteed yield strength of 50,000 psi. Bolts have an L bend on one end and threaded on the opposite end. Anchor bolts are completely hot dipped galvanized. Four (4) properly sized bolts, each furnished with two (2) regular hex nuts and two (2) flat washers, are provided per pole, unless otherwise specified. Poles 4.5" Straight Round Aluminum Cast Base HAND HOLE: All poles shall include a peripherally reinforced flush covered hand hole centered 18" above the bottom of the pole. The opening shal measure 3" X 5". POLE TOP CAP: Each pole assembly is provided with a removable composite frictionfit pole top cap. FINISH: Poles are available with bronze, natural or black Aluminum Association Architectural Class 1 anodized finish. Electrostatically applied, thermally cured TGIC polyester powdercoat finish or liquid polyurethane is also available. GENERAL POLE INFORMATION DESIGN: The poles as charted are designed to withstand dead loads and predicted dynamic loads developed by variable wind speeds with an additional 30% gust factor under the following conditions: The charted weights include luminaire(s) and/or mounting bracket(s). The wind velocities are based on 10 mph increments from 80 mph through 100 mph. Poles to be located in areas of known abnormal conditions may require special consideration. For example: coastal areas, airports and areas of special winds. Poles are designed for ground mounted applications. Poles mounted on structures (such as buildings and bridges) may also necessitate special consideration requiring Philips Gardco s recommendation. Height correction factors and drag coefficients are applied to the entire structure. An appropriate safety factor is maintained based on the minimum yield strength of the material incorporated in the pole. WARNING: This design information is intended as a general guideline only. The customer is solely responsible for proper selection of pole, luminaire, accessory and foundation under the given site conditions and intended usage. The addition of any items to the pole, in addition to the luminaire, will dramatically impact the EPA load on that pole. It is strongly recommended that a qualified professional be consulted to analyze the loads given the user s specific needs to ensure proper selection of the pole, luminaire, accessories, and foundation. Philips Gardco assumes no responsibility for such proper analysis or product selections. Failure to insure proper site analysis, pole selection, loads and installation can result in pole failure, leading to serious injury or property damage. GENERAL INFORMATION: Mounting height is the vertical distance from the base of the lighting pole to the center of the luminaire arm at the point of luminaire attachment.twin arms as charted are oriented at 180 with respect to each other. For applications of two (2) arms at or other multiple arm applications, consult the factory. WARRANTY: Philips Gardco poles feature a 1 year limited warranty. See Warranty Information on for complete details and exclusions Koninklijke Philips Electronics N.V. All Rights Reserved /0611

18 Page 4 of 4 Poles 4.5" Straight Round Aluminum Cast Base ORIENTATION INFORMATION FACTORY INSTALLED OPTIONS AND ACCESSORIES For Factory Installed Options and Accessories, Specify Orientation from Hand Hole and Height Above Pole Base Where Required. Height Above Pole Base HAND HOLE 0 Orientation is measured clockwise from the Hand Hole Center. STANDARD ARM MOUNT LUMINAIRE ORIENTATION D1 Drilled for Single Luminaire D2 Drilled for 2 Luminaires at 180 D3 Drilled for D1 Luminaire location 180 D2 180 D D3 D3 270 HAND HOLE 0 HAND HOLE D2 0 HAND HOLE 0 D4 Drilled for 4 Luminaires at D2@90 Drilled for 2 Luminaires at D3@120 Drilled for 3 Luminaires at D4 180 D2@ D3@120 D4 D4 270 D2@ HAND HOLE D4 HAND HOLE 60 from Hand Hole D3@120 HAND HOLE D3@ from Hand Hole Koninklijke Philips Electronics N.V. All Rights Reserved /0611

19 STYLE D SIGN STAR l 8 SN WATT S I G N L I G H T S OPTICS Narrow Spot Spot Unprecedented solidstate performance in a timeless style. By combining the classic design aesthetics of an RLM dome with our cutting edge BKSSL e technology, we ve taken sign lighting to a whole new level. Sign Star Style D is configurable up to 48 inches in length. Beneath the stylized dome is a fully adjustable solidstate source to place light exactly where desired. Keyword SND Medium Flood Wide Flood Rectilinear CCT 3K 4K R A G B MATERIAL ALU VOLTAGE 12V V Shown on a Power Canopy in Black Satin (BLP) finish 26 W W W. B K S S L. C O M

20 S I G N L I G H T S 3/8" (10mm) Specify Length 48" Maximum (1219mm) 1" Dia. (25mm) 21 1/4" (540mm) 45 RLM Reflector 10 3/4" Dia. (273mm) W W W. B K S S L. C O M 27

21 CATSKILL l 15 CK WATT 120V277V OPTICS Spot Flood The Catskill Series is designed for architectural up lighting or down lighting applications. With a projection of only four inches, the Catskill Series meets the ADA requirements for Architectural Surface lighting. The addition of our X technology makes this fixture a stylish and smart addition to any indoor or outdoor application. Visit for ordering logic. Keyword CK LED Wide Flood Rectilinear CCT 2.7K 3K 4K MATERIAL ALU ARCHITECTURAL SURFACE VOLTAGE V A/D CAP 3/8" (10mm) 4" (102mm) Shown with 'C' cap in Black Chrome (BCM) finish B/E CAP 7 9/16" (192mm) C CAP 3" Dia (76mm) DRIVER HOUSINGS: 84 PM2 DRM/RM PM2DRM

22 LED [Remote Transformer] Private Residence Lighting Design by Randall Whitehead Photo Doug Salin Shown with Mitique Brass Finish (MIT) 6

23 Catalog Number Logic Material B Series AR Source LED Housing RM Lamp e23 s Finish Lens MFL MAC 12 Material Shielding Cap Style Base Height A 12 Option PP Lens Blank Aluminum B Brass S Stainless Steel 12 Soft Focus Lens (Standard) 13 Rectilinear Lens Series Shielding AR ArtiStar 11 Honeycomb Baffle Source LED Solid State System with Integral Driver Cap Style Housing A B C D 45 Flush 45 less weephole (for Interior Use Only) E less weephole (for Interior Use Only) F cutoff with flush lens RM Requires Remote Transformer LED Type e22 8WLED/3K e23 8WLED/4K e24 8WLED/Red e25 8WLED/Green e26 8WLED/Blue e27 8WLED/Amber s NSP SP MFL WFL Narrow Spot (Red Indicator) Spot (Green Indicator) Medium Flood (Yellow Indicator) Wide Flood (Blue Indicator) Base Height Finish Aluminum & Brass Finishes Brass Powder Coat Color Satin Wrinkle Machined MAC Bronze BZP BZW Polished POL Black BLP BLW Mitique MIT White (Gloss) WHP WHW Aluminum SAP Verde VER Stainless Steel Machined 3'' with Anchor Base (Standard) 6'' with Anchor Base 12'' with Anchor Base 18'' with Anchor Base 24'' with Anchor Base Option PP Power Pipe option with 18'' Stake SF Stability Flange (for use with Power Pipe ) WM Wall or Ceiling Mount with 5'' dia. canopy* *Base height limited to 6'' max. with brass and stainless steel fixtures. MAC Polished POL Brushed BRU Interior Use only For lamp information, see page 40. See Pages 3839 for additional finish choices Specifications GreenSource Initiative Metal and packaging components are made from recycled materials. Manufactured using renewable solar energy, produced onsite. Returnable to manufacturer at end of life to ensure cradletocradle handling. Packaging contains no chlorofluorocarbons (CFC's). Use of this product may qualify for GreenSource efficacy and recycling rebate(s). Consult for program requirements. Materials Furnished in CopperFree Aluminum (Type 6061T6), Brass (Type 360) or Stainless Steel (Type 316). Body Fully machined from solid billet. Unibody design provides enclosed, waterproof wireway and integral heat sink for maximum component life. Integral knuckle for maximum mechanical strength. High temperature, silicone 'O' Ring provides watertight seal. Knuckle 'Aim and Lock' knuckle is comprised of two components. The first is integral to the body and features an interior, machined taper. The second is machined from solid billet and features a second, reverse angle taper. The resultant mechanical taperlock allows a full 180 vertical adjustment without the use of serrated teeth, which inherently limit aiming. High temperature, silicone 'O' Ring provides watertight seal and compressive resistance to maintain fixture position. Design withstands 73 lb. static load prior to movement to ensure decades of optical alignment. Biaxial source control with 360 horizontal rotation in addition to vertical adjustment. Cap Fully machined. Accommodates [1] lens or louver media. Choose from 45 cutoff ('A' or 'D'), 1 deep bezel with cutoff ('B' or 'E'), or flush lens ('C') cap styles. 'A' and 'B' caps include weephole for water and debris drainage. 'D' and 'E' caps exclude weephole and are for interior use only. Lens Shock resistant, tempered, glass lens is factory adhered to fixture cap and provides hermetically sealed optical compartment. Specify soft focus (#12) or rectilinear (#13) lens. BKSSL Integrated solid state system with 'e' technology is scalable for field upgrade. Modular design with electrical quick disconnects permit field maintenance. High power, forward throw source complies with ANSI C binning requirements. Exceeds ENERGY STAR lumen maintenance requirements. LM80 certified. Integral nondimming driver. Minimum 50,000 hour rated life at 70% of initial lumens (L70). BKSSL technology provides long life, significant energy reduction and exceptional thermal management. s Interchangeable OPTIKIT modules permit field changes to optical distribution. Colorcoded for easy reference. Installation Machined anchor base with 7/8 dia. slip conduit hole and [3] 3/16 dia. anchor bolt holes (hardware by others). Available in standard increments to facilitate fixture elevation above grade. Optional 18 Power Pipe for direct burial into soil or concrete. Power Pipe additionally features optional 6 diameter, molded stability flange, which simplifies installation and projects into substrate to reinforce housing stability. Optional 5 dia. machined canopy permits mounting to junction box (gasket by others). 6 maximum base height for canopymounted brass or stainless steel fixture. 2 1/4" Dia A/D Cap 4 1/2" 3 1/8" 4 1/2" Transformer For use with 12VAC remote transformer. B/E Cap Wiring Teflon coated, 18AWG, 600V, 250 C rated and certified to UL 1659 standard. 2 3/8" 7/8" 3" 1/8" Hardware Tamperresistant, stainless steel hardware. Knuckle vertical aiming screw is additionally black oxide treated for additional corrosion resistance. Finish StarGuard (Pat. Pend.), a RoHs compliant, 15 stage chromatefree process cleans and conversion coats aluminum components prior to application of Class 'A' TGIC polyester powder coating. Brass components are available in powder coat or handcrafted metal finish. Stainless steel components are available in handcrafted metal finish. (Brushed finish for interior use only). Warranty 5 year limited warranty. C Cap 1 1/2" F Cap 2" POWER PIPE STANDARD BASE 7/8" Dia 1/4" Dia 120 Apart 2 1/4" Dia 5/8" WALL MOUNT CANOPY 3 1/2" O.C. Certification and Listing ITL tested to IESNA LM79. Lighting Facts Registration per USDOE ( ETL Listed to ANSI/UL Standard 1838 and UL Standard Certified to CAN/CSA Standard C22.2 No. 9. RoHs compliant. Suitable for indoor or outdoor use. Suitable for use in wet locations. Suitable for installation within 4 of the ground. Made in USA. 5" Dia 7