Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Accessory Guide

Transcription

1 Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Accessory Guide First Published: Last Modified: Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA USA Tel: NETS (6387) Fax:

2 THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY. The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense. The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users are encouraged to try to correct the interference by using one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB s public domain version of the UNIX operating system. All rights reserved. Copyright 1981, Regents of the University of California. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED "AS IS" WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE. IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: / Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1721R) 2018 Cisco Systems, Inc. All rights reserved.

3 CONTENTS Preface Preface v Accessory Guidelines v Important Headset Safety Information v Related Documentation vi Documentation, Support, and Security Guidelines vi Cisco Product Security Overview vi CHAPTER 1 Cisco Accessories 1 Batteries 1 AC Power Supply 2 Charge Phone Using AC Power Supply 3 Cisco Unified Wireless IP Phone 7925G Multicharger 3 Cisco Unified Wireless IP Phone 7925G Desktop Charger 4 Cisco Unified Wireless IP Phones Lock Set 5 Install Phone Lock Set 5 Carry Cases 6 Holster Carry Cases 6 Leather Carry Cases 7 Cisco Unified Wireless IP Phone 7925G Ruggedized Case 8 USB Cable 9 CHAPTER 2 Third-Party Accessories 11 Third-Party Accessories Overview 11 Headsets 11 Bluetooth Wireless Headsets 11 Headset Choices 12 iii

4 Contents CHAPTER 3 Cisco Accessory Part Numbers 13 iv

5 Preface Accessory Guidelines, page v Related Documentation, page vi Documentation, Support, and Security Guidelines, page vi Cisco Product Security Overview, page vi Accessory Guidelines Follow these guidelines when using accessories with your Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G: Use only chargers, batteries, and accessories that are approved by the phone manufacturer. Use of unapproved chargers, batteries, and accessories might be dangerous, and invalidates the warranty on your phone. Do not adhere a clip to the back of the phone or insert a clip between the phone and battery cover because it can damage the battery. When disconnecting the power cord of any accessory, grasp and pull the plug. Do not pull the cord. Keep accessories out of the reach of young children. Clean the phone with a soft, dry cloth or a moist wipe. The phone is resistant to dust and spills, but you can further protect your phone with a cover case. Important Headset Safety Information High Sound Pressure Avoid listening to high volume levels for long periods to prevent possible hearing damage. When you plug in your headset, lower the volume of the headset speaker before you put the headset on. If you remember to lower the volume before you take the headset off, the volume will start lower when you plug in your headset again. v

6 Related Documentation Preface Be aware of your surroundings. When you use your headset, it may block out important external sounds, particularly in emergencies or in noisy environments. Don t use the headset while driving. Don t leave your headset or headset cables in an area where people or pets can trip over them. Always supervise children who are near your headset or headset cables. Related Documentation For more information, see the documentation for the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G at this URL: Note For the latest information about the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G, refer to the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Firmware Release Notes for Cisco Unified Communications Manager. You can access the release notes from Cisco.com by performing a keyword search for 7925G release notes. Documentation, Support, and Security Guidelines For information on obtaining documentation, obtaining support, providing documentation feedback, reviewing security guidelines, and also recommended aliases and general Cisco documents, see the monthly What s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: Subscribe to the What s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0. Cisco Product Security Overview This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer, and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute, or use encryption. Importers, exporters, distributors, and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. Further information regarding U.S. export regulations may be found at regulations/export-administration-regulations-ear. vi

7 CHAPTER 1 Cisco Accessories Batteries, page 1 AC Power Supply, page 2 Cisco Unified Wireless IP Phone 7925G Multicharger, page 3 Cisco Unified Wireless IP Phone 7925G Desktop Charger, page 4 Cisco Unified Wireless IP Phones Lock Set, page 5 Carry Cases, page 6 USB Cable, page 9 Batteries Batteries for the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G are not included with the phone and must be ordered separately. See your local representative for more information. The following table describes the battery types. Refer to the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G User Guide for instructions on installing your battery. Caution Use only batteries that are approved by the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G manufacturer. Use of unapproved batteries might be dangerous, and will invalidate the warranty on your phone. Table 1: Battery Types for the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Type Technology Talk Time Standby Time Battery Part Numbers Standard Lithium ion Up to 9.5 hours Up to 180 hours CP-BATT-7925G-STD= Extended Lithium ion Up to 13 hours Up to 240 hours CP-BATT-7925G-EXT= 1

8 AC Power Supply Cisco Accessories Note Using a Bluetooth wireless headset affects battery life and reduces the talk time. In addition, how the system administrator configures the phone also affects its battery life. For more information, see your system administrator. AC Power Supply The power supply with AC plug adapter enables you to quickly charge your phone battery. You can use the phone while you are charging the battery. The following table provides approximate battery charging times for the two battery types and power supply configurations. You can check the battery charging state on the phone display. Table 2: Approximate Battery Charging Times Battery type Standard Extended Power supply connected to phone 2 hours 3 hours Phone connected to computer with USB cable 5 hours 7 hours Caution Use only Cisco-specified AC power supplies for the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G. 2

9 Cisco Accessories Charge Phone Using AC Power Supply Charge Phone Using AC Power Supply The following figure describes how you set up the phone to charge with the AC power supply. The numbers refer to the procedure steps. Figure 1: AC Power Supply Procedure Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Lift the mini-usb port cover at bottom of phone. Swing the port cover to one side. Insert the AC power supply mini-usb connector in the port. Insert the AC plug adapter in the slot on the power supply. Insert the AC power supply in a wall outlet. Verify that the Indicator LED is red. Red indicates that the battery is charging. The LED turns green when battery is charged. Cisco Unified Wireless IP Phone 7925G Multicharger The Cisco Unified Wireless IP Phone 7925G Multicharger can charge up to six phones and six batteries at the same time, as shown in the following figure. 3

10 Cisco Unified Wireless IP Phone 7925G Desktop Charger Cisco Accessories For more information, see the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Multicharger Installation Guide. Figure 2: Cisco Unified Wireless IP Phone 7925G Multicharger Cisco Unified Wireless IP Phone 7925G Desktop Charger The Cisco Unified Wireless IP Phone 7925G Desktop Charger provides the following features: Works on line power or from a charged spare battery for the phone Contains two LEDs: Power LED: Lights green when powered on, lights blue when using Bluetooth Battery LED: Lights red when charging, green when fully charged, yellow when powered by the phone battery Contains a speakerphone with the volume controlled by the phone volume buttons Supports Bluetooth Charges the docked phone battery Contains an additional charging port at the back of the station for charging a spare battery For more information, see the following documents: 4

11 Cisco Accessories Cisco Unified Wireless IP Phones Lock Set Cisco Unified Wireless IP Phone 7925G Desktop Charger Getting Started Guide Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G User Guide Cisco Unified Wireless IP Phones Lock Set The Cisco Unified Wireless IP Phones Lock Set includes the cable, the C-ring, and the combination lock. The security slot can accommodate a lock up to 20 mm. Compatible laptop cable locks include the Kensington laptop cable lock and other manufacturers' cable locks that fit into the security slot on the left side of the desktop charger. Note Cisco does not supply a laptop cable lock; you must purchase a cable lock from your local electronics supply source. Install Phone Lock Set Figure 3: Lock Set for the Phone To install the lock on the phone, see the preceding figure and follow these steps: 5

12 Carry Cases Cisco Accessories Procedure Step 1 Step 2 Step 3 Put the cable (with loops at each end) around a post or cable that is used to lock your computer, and then put the two loops at the ends of the cable in the C-ring. Insert the C-ring in the slot on the back of the phone. Using the combination lock, fasten the two ends of the C-ring together to secure the phone. Carry Cases Carry cases make it easy to keep the Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G with you and provide some protection for the phone. The following sections describe the available carry cases. Holster Carry Cases The holster carry case is a hard plastic case that holds the phone and has a clip on the back that rotates 180 degrees. Use the clip to secure the phone to a belt or pocket. There are two holster cases available: Cisco Unified Wireless IP Phone 7925G Holster Case and Cisco Unified Wireless IP Phone 7926G Holster Case. The following figure shows the Cisco Unified Wireless IP Phone 7925G Holster Case. The Cisco Unified Wireless IP Phone 7926G Holster Case is similar in appearance, but is shaped differently to accommodate the bar code scanner of the Cisco Unified Wireless IP Phone 7926G. Figure 4: Cisco Unified Wireless IP Phone 7925G Holster Carry Case 6

13 Cisco Accessories Leather Carry Cases Leather Carry Cases A leather carry case makes it easy to keep the phone with you and provide protection for the phone. There are two leather cases available: Cisco Unified Wireless IP Phone 7925G Leather Carry Case and Cisco Unified Wireless IP Phone 7926G Leather Carry Case. Features of the leather carry case include: A clear plastic window that allows you to view the screen and provides easy access to the keys and buttons. Openings for the microphone, headset port, and mini-usb port that allow you to use and charge the phone without removing the leather carry case. A removable belt clip on the back that rotates 360 degrees. A security cord with a ring on one end that slides onto the D-ring on the back of the carry case. You can fasten the other end of the cord to a belt loop to secure the phone. Note After you insert the phone in the leather carry case, you may need to adjust the alignment so the microphone (at bottom of phone) is not covered. The following figure shows the Cisco Unified Wireless IP Phone 7925G Leather Carry Case. The Cisco Unified Wireless IP Phone 7926G Leather Carry Case is similar, but the bar code scanner of the Cisco Unified Wireless IP Phone 7926G is accessible without removing the case. Figure 5: Cisco Unified Wireless IP Phone 7925G Leather Carry Case with Phone 7

14 Cisco Unified Wireless IP Phone 7925G Ruggedized Case Cisco Accessories The following figure shows the bottom of the phone when in the leather case. Figure 6: Leather Case Opening for Microphone and Mini-USB Port 1 Microphone 2 Mini-USB port with cover Cisco Unified Wireless IP Phone 7925G Ruggedized Case The Cisco Unified Wireless IP Phone 7925G Ruggedized Case protects the Cisco Unified Wireless IP Phone 7925G. This protective case reduces damage if the phone is frequently dropped. The following figure shows the phone installed in the protective case. Figure 7: Installed Cisco Unified Wireless IP Phone 7925G Ruggedized Case Two clips that can attach to the back of case are provided: Pocket clip for holding the phone in a pocket Belt clip for holding the phone to a belt Note The case does not fit the Cisco Unified Wireless IP Phone 7926G. 8

15 Cisco Accessories USB Cable USB Cable You can use a standard or Cisco USB cable to connect your Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G to a computer to configure a new phone for the first time or to charge the phone battery. The following figure shows how to connect the phone to a computer. Figure 8: USB cable connecting the phone to a PC Mini-USB connector for the phone. Standard USB connector for the PC. Indicator light: LED is red while battery is charging and turns green when battery is charged. 9

16 USB Cable Cisco Accessories 10

17 CHAPTER 2 Third-Party Accessories Third-Party Accessories Overview, page 11 Headsets, page 11 Third-Party Accessories Overview Accessories for the wireless phones are available from third parties. Note Cisco does not test third-party accessories. Cisco recommends that you test them in your environment before providing them to users. Headsets The wireless phone supports the use of third-party wired and Bluetooth wireless headsets. For wired headsets, the phone requires a headset or ear bud with a 2.5 mm, 3-band, 4-conductor plug. Related Topics Important Headset Safety Information, on page v Bluetooth Wireless Headsets Using Bluetooth wireless headsets increases battery power consumption on your phone and results in reduced talk time. For a Bluetooth wireless headset to work, it does not need to be within direct line-of-sight of the phone, but some barriers, such as walls or doors, and interference from other electronic devices, can affect the connection. 11

18 Headset Choices Third-Party Accessories Headset Choices The audio portion of a headset must sound good to you and the person you are speaking to. Sound is subjective and we cannot guarantee the performance of any headsets. Some of the headsets on the sites listed below have been reported to perform well on wireless IP Phones. For information about headsets, go to the following URLs: Note We recommend that you test your headsets in your own environment to determine suitable performance. 12

19 CHAPTER 3 Cisco Accessory Part Numbers The following table lists all accessories that you can order from Cisco and their part numbers. To purchase these accessories, contact your local dealer or corporate representative. Table 3: Cisco Unified Wireless IP Phone Accessories Phone Accessories Standard battery Extended battery Cisco Unified Wireless IP Phone 7925G Holster Carry Case Cisco Unified Wireless IP Phone 7925G Leather Carry Case Cisco Unified Wireless IP Phone 7926G Holster with integrated clip Cisco Unified Wireless IP Phone 7926G Leather case with belt clip USB cable for phone Cisco Unified Wireless IP Phone Lock Set Phone power supply for Australia and New Zealand Phone power supply for Central Europe Phone power supply for China Phone power supply for Argentina Phone power supply for Japan Phone power supply for North America Part Number CP-BATT-7925G-STD= CP-BATT-7925G-EXT= CP-HOLSTER-7925G= CP-CASE-7925G= CP-HOLSTER-7926G= CP-CASE-7926G= CP-CAB-USB-7925G= CP-LOCK-7921G= CP-PWR-7925G-AU= CP-PWR-7925G-CE= CP-PWR-7925G-CN= CP-PWR-7925G-AR= CP-PWR-7925G-JP= CP-PWR-7925G-NA= 13

20 Cisco Accessory Part Numbers Phone Accessories Phone power supply for United Kingdom Cisco Unified Wireless IP Phone 7925G Desktop Charger bundle Cisco Unified Wireless IP Phone 7925G Desktop Charger spare (power supply not included) Cisco Unified Wireless IP Phone 7925G Desktop Charger power supply (Argentina) Cisco Unified Wireless IP Phone 7925G Desktop Charger power supply (Australia) Cisco Unified Wireless IP Phone 7925G Desktop Charger power supply (Europe) Cisco Unified Wireless IP Phone 7925G Desktop Charger power supply (China) Cisco Unified Wireless IP Phone 7925G Desktop Charger power supply (Japan) Cisco Unified Wireless IP Phone 7925G Desktop Charger power supply (North America) Cisco Unified Wireless IP Phone 7925G Desktop Charger power supply (United Kingdom) Cisco Unified Wireless IP Phone 7925G Ruggedized Case Cisco Unified Wireless IP Phone 7925G Multi Charger bundle Cisco Unified Wireless IP Phone 7925G Multi Charger bundle (EU only) Cisco Unified Wireless IP Phone 7925G Multi Charger spare (power supply not included) Cisco Unified Wireless IP Phone 7925G Multi Charger power supply Cisco Unified Wireless IP Phone 7925G Multi Charger power supply (EU only) Part Number CP-PWR-7925G-UK= CP-DSKCH-7925G-BUN CP-DSKCH-7925G= CP-PWR-DC7925G-AR= CP-PWR-DC7925G-AU= CP-PWR-DC7925G-CE= CP-PWR-DC7925G-CN= CP-PWR-DC7925G-JP= CP-PWR-DC7925G-NA= CP-PWR-DC7925G-UK= CP-RUG-CASE-7925G= CP-MCHGR-7925G-BUN CP-MCHGR-7925G-EU CP-MCHGR-7925G= CP-PWR-MC7925G= CP-PWR-MC7925G-EU= 14