WIFI CAM Instruction Point-to-point WIFICAM Makes Monitoring Easier and Safer.

Transcription

1 WIFI CAM Instruction Point-to-point WIFICAM Makes Monitoring Easier and Safer. Brief Introduction WIFICAM is a new kind of wireless WIFI signal lens. With WIFICAM, you may install monitoring software in IPHONE or Android cellphone and computer, the signal connecting with WIFICAM will conduct image monitoring on your smart phone and computer. What characteristics does WIFICAM have? Different with ordinary 2.4GHZ baby monitor, WIFICAM doesn t need display to receive image, rendering your smart phone to receive image at any time. Different with IP Camera, WIFICAM doesn t have complex setting debugging. Just simple signal is needed to complete configuration. Different with car recorder, WIFICAM doesn t need to take out memory card to copy videos and images. In contrast, your smart phone may conduct timely playback, and upload it on the internet Different with other wireless lens, WIFICAM adopts WAP signal encryption, absolutely guaranteeing your privacy. More importantly, image signal will not be intercepted or stolen. Introduction to WIFICAM Appearance WIFICAM signal antenna 2 ---Infrared night vision light 3 ---lens 4 ---Indicator light 5 ---Power switch 6 ---Resetting key 7 ---Power interface 8 ---Bracket interface Introduction to WIFICAM operation: 1) First of all, connect signal antenna with WIFICAM 2) Then connect WIFICAM with battery or power supply 3) Switch WIFICAM to ON for starting up, and indicator light will show continuous blue light; Switch WIFICAM to OFF for shutdown, and the blue light extinguishes. *After the starting up of WIFICAM, use computer or cellphone pre-installed with WIFICAM software to search and connect

2 with WIFICAM signal for monitoring. Operation Method for Computer Software 1) First of all, Copy in CD to computer PC hard disk for unzipping. There will be executable file in unzipped file shown as. 2) Open WIFICAM power switch, then open computer WIFI signal for searching and find WIFI CAM signal (Name: camera_ ) and click it for connecting. *Note: WIFICAM signal name may be modified and encrypted through update equipment function of computer WIFCAM software. 3) Start software, and click Refresh, then monitoring image appears 4) Introduction to WIFICAM computer software function operation. Operation Interface is shown as follows: Language. Here you can choose ten languages such as English, Arabic, Simplified Chinese, Traditional Chinese, French, Japanese, Polish, Korean, Russian and Spanish. Update to Device----- Set WIFI SSID and password for WIFI CAM here(namely modify WIFICAM signal and password) * The wifi signal name to be modified shall be modified in the form of camera_ , such as wificam_ Password is 8 numbers. Mark WAP Personal Encryption, and click to update to equipment. Finally, re-start up. Snaphoto and record Route, click to choose where the image file is saved. Take photos. Click to take photos; Record videos. Click video to record a video. Resolution ratio----here two resolution ratios are offered: 320*240 or 640*480 Frequency range: 50HZ ; 60HZ(signal frequency range) Video up-down overturn----when click it, the video will overturn in up-down direction Video left-right overturn----when click it, the video will overturn in right-left direction Refresh Click Refresh to refresh present image

3 Operation Method of IPHONE Software 1) Download WIFICAM software from APP STORE (website: or scan QRCode ) 2) After the software is successfully installed, icon appears. 3) Start cellphone WIFI signal setting to connect with WIFICAM signal 4) After signal is connected successfully, start WIFICAM software and click Refresh, then monitoring image will appear 5) Operation introduction to IPHONE software function of WIFICAM Apple Operation Interface is shown as follows: Take photos click to capture pictures Video click to record videos Refresh click to refresh equipment Setting click to enter setting All the photos and videos taken is saved in IPHONE S. Operation Method for Android Cellphone Software 1: First of all, use computer data wire to connect with your Android cellphone, and double click for installation operation. 2: After successful installation, start cellphone WIFI setting and connect lens WIFI signal 3: After successful connection, start WIFICAM software for image monitoring *Note: Android cellphone s operation method is same with IPHONE s, and will not be introduced separately.

4 Detail parameters: Lens: 1/4 CMOS Angle: 140 Pixel:300k Minimum illumination: 0 Lux with LED On Lens: f=4.3mm, F=1.8, Manual Focus Night vision light: 10x 850nm Infrared LEDs, 10m distance Resolution ratio: 640*480(VGA), 320*240(QVGA) Picture format: JPEG Video format: avi Frame number: 20fps Bit rate: 128kbps ~ 2Mbpsb Picture resolution rate: Mirror /Flip Video compression: ADPCM Networking protocol: TCP/IP, UDP/IP, HTTP, DHCP WBit rateifi: b/g/n WBit rateifi: b/g/n Security encryption mode: WAP Transmission distance: about 50 m Battery capacity: 1000 mah Operation hours: about 2-4 hours Charging time: 4~5h Operation temperature: 0 ~50 Operation humidity: 10% ~ 80% non-condensing Compatible System: Windows, Mac, ipad, iphone, Android Language: English, Arabic, Simplified Chinese, Traditional Chinese, French, Japanese, Polish language, Korean, Russian language and Spanish Volume: 90x60x60mm Certification: CE, FCC, RoHS Accessory Package Contents Camera *1 Antenna*1 CD *1 Charging Adapter *1 Car Adapter*1 Suction cup*1

5 Frequently asked questions: Q:Image freeze-frame? A: There are two reasons for freeze-frame One is weak signal. Put it in a place with strong signals. Second is slow processing speed of terminal equipment, and click Refresh. Q: Image is upside-down? A: Start software settings and choose appropriate image display mode Q: Support always connecting with power supply? A: Yes, you can always connect it with power supply, but you should install given battery first. Q: Forget modified WIFICAM password or signal name? A: Press resetting key for a long time then restart. All data will be restored to original state. Q: Fails to change WIFI SSID name or password? A: Please check whether filled WIFI SSID is correct or not. The correct format is: name ++_ +( _).( _).(_).(_). For example: camera_ Correct password format is 8 numbers. Q: After connecting with WIFICAM, internet is still not available in the laptop? A: As WIFICAM s signal is Wireless Local Area Network signal, computer internet port will be used after connection. You simply need to insert network cable or install another WIFI adapter. Q: After being connected with WIFICAM, the cellphone still fails to get access to internet? A: As the connection with WIFICAM signal will use cellphone internet port, the internet is not available. Please disconnect with WIFCAM signal. Q: How to change language of the software? A: WIFICAM software has 9 languages inside. Software will change automatically according to system language, so you only need to change system language. The existing languages are: English, Arabic, Simplified Chinese, Traditional Chinese, French, Japanese, Polish, Korean, Russian and Spanish Q: WIFICAM signal is not available? A: Please ensure the normal starting up of WIFICAM power supply. Q: Emulational mobile phone fails to connect with WIFICAM? A: As emulational mobile phone s WIFI signal module is badly made, it can t get access to WIFICAM. Q:how to solve with the blurred screen or splash screen problem? A:it course by the low power,just need to recharge the battery or change the battery. Note: The current vision only supports image transmission temporarily and still fails to support sound & video at the same time. If WIFICAM was set the password, it only can be connet by one monrt!