STARTUP GUIDE. SP en-us ENGLISH

Transcription

1 Anybus PoEInjector VAC STARTUP GUIDE ENGLISH

2 Important User Information Liability Every care has been taken in the preparation of this document. Please inform HMS Industrial Networks AB of any inaccuracies or omissions. The data and illustrations found in this document are not binding. We, HMS Industrial Networks AB, reserve the right to modify our products in line with our policy of continuous product development. The information in this document is subject to change without notice and should not be considered as a commitment by HMS Industrial Networks AB. HMS Industrial Networks AB assumes no responsibility for any errors that may appear in this document. There are many applications of this product. Those responsible for the use of this device must ensure that all the necessary steps have been taken to verify that the applications meet all performance and safety requirements including any applicable laws, regulations, codes, and standards. HMS Industrial Networks AB will under no circumstances assume liability or responsibility for any problems that may arise as a result from the use of undocumented features, timing, or functional side effects found outside the documented scope of this product. The effects caused by any direct or indirect use of such aspects of the product are undefined, and may include e.g. compatibility issues and stability issues. The examples and illustrations in this document are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular implementation, HMS Industrial Networks AB cannot assume responsibility for actual use based on these examples and illustrations. Intellectual Property Rights HMS Industrial Networks AB has intellectual property rights relating to technology embodied in the product described in this document. These intellectual property rights may include patents and pending patent applications in the USA and other countries.

3 About This Document 3 (8) 1 About This Document This document describes how to install Anybus PoE Injector VAC. For additional documentation and technical support regarding this product, please visit Document Conventions The following formatting conventions are used in this document to indicate safety information and other content of specific importance: WARNING This instruction must be followed to avoid a risk of death or serious injury. Caution This instruction must be followed to avoid a risk of personal injury. This instruction must be followed to avoid a risk of reduced functionality and/or damage to the equipment, or to avoid a network security risk. This is additional information which may facilitate installation and/or operation.

4 Description 4 (8) 2 Description Anybus PoE Injector VAC is a dual port 802.3af/at compliant Power over Ethernet injector with Midspan Intelligent Detection. The PoE injector will not turn on power until it detects a valid PoE signature from the devices attached downstream on the Ethernet cable. This protects non-compliant equipment against damage. Anybus PoE Injector VAC will not function with equipment that is not fully compliant with the IEEE 802.3af/at PoE standards. Fig. 1 Dimensions

5 Installation 5 (8) 3 Installation Fig. 2 RJ45 Ethernet connectors RJ45 pinning Pin Name IN (data only) OUT (data + power) 1 Rx+ Data Receive Data Receive 2 Rx- Data Receive Data Receive 3 Tx+ Data Transmit Data Transmit 4 -Vdc_return(+) (not connected) Feeding power(+) 5 -Vdc_return(+) (not connected) Feeding power(+) 6 Tx- Data Transmit Data Transmit 7 -Vdc (not connected) Feeding power(-) 8 -Vdc (not connected) Feeding power(-) Do not connect pins 7 or 8 to ground.

6 This page intentionally left blank

7 Appendix A: Technical Data 7 (8) A Technical Data A.1 Technical Specifications Order code AWB4005-B PoE standard IEEE 802.3at/802.3af Ethernet IN 1 x RJ45 (Data, 10/100/1000 Base-T(x)) Ethernet OUT 1 x RJ45 (Data and power, 10/100/1000 Base-T(x)) Input voltage VAC Output voltage 56 V / W LED power indicator LED PoE indicators 1 x LED (power, error) Short circuit protection Yes Overload protection Yes High voltage protection Yes Mounting Wall mount with screws Weight 210 g Protection class Storage temperature -40 to +85 C Operating temperature -25 to +60 C Housing Plastic (PC) Dimensions W H D 75 x 125 x 38 Certifications See datasheet Disposal and recycling You must dispose of this product properly according to local laws and regulations. Because this product contains electronic components, it must be disposed of separately from household waste. When this product reaches its end of life, contact local authorities to learn about disposal and recycling options, or simply drop it off at your local HMS office or return it to HMS. For more information, see

8 last page 2019 HMS Industrial Networks Box Halmstad, Sweden / / 9217