NR8201/8301. NR CH Viewing & Recording External esata Interface. NR CH Viewing & Recording RAID 0, 1 Scalable Storage. Rev. 1.

Size: px

Start display at page:

Download "NR8201/8301. NR CH Viewing & Recording External esata Interface. NR CH Viewing & Recording RAID 0, 1 Scalable Storage. Rev. 1."

Wendy Leonard
6 years ago
Views:

1 NR8201/8301 H.264 Compatible with VAST CMS Lockable HDD & Rack Mount Design NR CH Viewing & Recording External esata Interface NR CH Viewing & Recording RAID 0, 1 Scalable Storage Rev. 1.1

2 Warning Before Installation English Power off the Network Video Recorder as soon as it is found smoking or smelt unusual. Keep the Network Video Recorder away from water. If the Video Recorder is wet, power off immediately. Contact your distributor when such cases happen. Contact your distributor when such cases happen. Do not place the Network Video Recorder around the heat sources, such as television or oven. Refer to your user's manual for the operating temperature. Keep the Network Video Recorder away from direct sunlight. Do not place the Network Video Recorder in high humidity environments. EN - 1

3 Do not place the Network Video Recorder on unsteady surfaces. Do not touch the Network Video Recorder when it's lightening. Do not drop the Network Video Recorder. Do not insert any object into the Network Video Recorder, such as needles. EN - 2

4 WAN LAN1 LAN2 LAN3 LAN G NR8201 Network Video Recorder 1 Package Contents English NR8201 (4CH) or NR8301 (8CH) Power Cord NR8201 NR8301 Software CD Rack Mount Kit NR8201: Rack Mount Ear x 2 Screws x 4 (Black) Screws x 4 (Grey) Key x 2 NR8301: Rack Mount Ear x 2 Screws x 4 (Black) Screws x 8 (Grey) Key x 2 Warranty Card Quick Installation Guide EN - 3

5 Power Status PoE HDD Power Status PoE HDD WAN LAN1 LAN2 LAN3 LAN4 RESET NR8201 Network Video Recorder RESET esata Physical Description NR8301 USB Socket Status Indicator Removable & Lockable Hard Disk Trays x 2 Power Cord Socket Ethernet 10/100 RJ45 Socket x 8 (LAN); Gigabit Ethernet RJ45 Socket x 1 (WAN) LAN2 LAN4 LAN6 LAN8 POWER AC IN 100V-240V LAN1 LAN3 LAN5 LAN7 WAN Power Button Recessed Reset Button General I/O Terminal Block NR8201 Status Indicator Removable & Lockable Hard Disk Tray x 1 USB Socket Power Cord Socket Ethernet 10/100 RJ45 Socket x 4 (LAN); Gigabit Ethernet RJ45 Socket x 1 (WAN) esata Socket POWER AC IN 100V-240V LAN1 LAN3 LAN5 LAN7 WAN Power Button Recessed Reset Button General I/O Terminal Block EN - 4

6 3 Hardware Installation English Before using the Network Video Recorder, please prepare SATA hard disk(s) for recording video. 1. Make sure the power is disconnected. 2. Install the supplied rack mount ears if you want to install the enclosure into a rack cabinet. 3. Open the drive tray bezel as shown below and remove the drive trays. 4. Install your hard disk to the drive tray, and secure it with the supplied four screws. 5. Open the drive tray bezel and insert hard disk(s) into the drive bays. 6. Use the supplied bezel key to lock the drive trays in place to prevent unauthorized access EN - 5

7 WAN LAN1 LAN2 LAN3 LAN4 POWER NR8201 Network Video Recorder AC IN 100V-240V Power/MIC Activity RESET Power/MIC LAN2 LAN1 Activity LAN4 LAN3 LAN6 LAN5 LAN8 LAN7 WAN Network Deployment 1. Connect the supplied power cable from the Network Video Recorder (NVR) to a power outlet. 2. Push the power button to run the NVR. 3. Connect network cameras to the NVR s PoE LAN ports. Connect a management PC to the WAN port directly or via LAN. The NVR comes with an embedded DHCP server for its LAN ports. It is necessary to configure the LAN ports and the WAN port into different Class C subnets, e.g., xxx for LAN and xxx for WAN. 4. If you want to access NVR over the Internet, connect the NVR to the Internet via the WAN port. 5. If you have external devices such as sensors and alarms, make connections from the general I/O terminal block. NVR embedded DHCP server Private LAN LAN 4 3 Cable, DSL Modem, or router Network Camera (PoE) Internet x8 Class C subnet #0 Class C subnet #1 Management PC 3 NR CH PoE Data Transmitting Power Supply 4-CH PoE Data Transmitting 5 1: Power 2: Relay output COM 3: Relay output N.O. 4: Digital Input 1 5: Digital Input 1 Ground 6: Digital Input 2 7: Digital Input 2 Ground 8: Digital Input 3 9: Digital Input 3 Ground 10: Digital Input 4 11: Digital Input 4 Ground 12: Ground NR8201 Power Supply EN - 6

5 Assigning an IP Address English 1. 1-1. If your local network does not have a DHCP server, you may temporarily connect a PC to a LAN port for initial configuration.

If your local network has a DHCP server, connect the WAN port to your local network, and use the IW2 utility to find the NVR server IP.

You may let DHCP server assign an IP to your NVR WAN port - or - if you need to access NVR over Internet, please configure a WAN port IP address in Router/firewall using port forwarding or DMZ. 2.

There are three ways to get WAN IP address: DHCP (Dynamic IP), Static IP address, and PPPoE (DSL).

8 5 Assigning an IP Address English If your local network does not have a DHCP server, you may temporarily connect a PC to a LAN port for initial configuration. The NVR comes with a default IP, You can access the NVR server using this IP, and then manaully assign an IP to the NVR WAN port If your local network has a DHCP server, connect the WAN port to your local network, and use the IW2 utility to find the NVR server IP. You may then access the NVR server by entering the discovered IP in the address bar of a web browser. 1-3 Once connected to the NVR server, please keep the LAN setting as default. You may let DHCP server assign an IP to your NVR WAN port - or - if you need to access NVR over Internet, please configure a WAN port IP address in Router/firewall using port forwarding or DMZ. 2. If you need to access NVR over the Internet, please assign a WAN IP address in the configuration page. You may use DDNS for Internet access. There are three ways to get WAN IP address: DHCP (Dynamic IP), Static IP address, and PPPoE (DSL). If your network environment is DHCP, you can use VIVOTEK Installation Wizard 2 (IW2) to discover the IP address for the WAN port. (1) Install Installation Wizard 2 from the Software Utility directory on the software CD. (2) The program will conduct an analysis of your network environment. After your network is analyzed, please click on the Next button to continue the program. Installation Wizard 2 (3) The program will search the VIVOTEK Network Devices on the same LAN. (4) After searching, the main installer window will pop up. Click on the MAC that matches the one labeled on your device to connect to the Network Video Recorder via Internet Explorer D F NR D107893F NR D107893F 3. Use the WAN IP address to access the Network Video Recorder from the Internet. EN - 7

recorded video, you have to add devices to the Network Video Recorder on the

9 6 Ready to Use Following is the Homepage of the Network Video Recorder. Configuration page Note If you want to record live video and playback the recorded video, you have to add devices to the Network Video Recorder on the Configuration page. For further setup, please refer to user's manual on the software CD. EN - 8

Warning Before Installation

Warning Before Installation English Power off the Network Video Recorder as soon as it is found smoking or smelt unusual. Keep the Network Video Recorder away from water. If the Network Camera is wet,