Loop IP6510-LN Multiple WAN Router

Transcription

1 Loop IP6510-LN Multiple WAN Router Description The IP6510-LN Multiple WAN Edge Router has IPv4/IPv6 dual stack functionality and Level 3 Routing in a single unified device. It is suitable for large deployments that require only moderate bandwidth and a small port density but a very competitive CapEx. The LN stands for Linux, which backs up the Loop-OS architecture inside the IP6510-LN. The new Loop-OS includes many advanced features with more functionality to help you improve your network. These features inside the Loop-OS include IPv4/IPv6 dual stack routing capability, software bridging*, serial-to-ip/udp terminal services*, and network security features. With RIPng, OSPFv3 and BGP-4, the IP6510-LN is able to build a reliable IPv6 routed network. All WAN ports and LAN ports can be configured into bridge mode*, router mode, or combinations of both. WAN interfaces including Ethernet, E1/T1 and Serial RS232/RS485 provide flexibility for any access network. Using VPN connectivity over IPSec included in the Loop-OS software suite allows a highly secure and reliable connection over an IP-based network to any location. Features Mechanical and Electrical 2 Tributary Slots for WAN interfaces Power Module AC and DC coexist AC power: 100 to 240 Vac, 0.8 A DC power: -36 to -72 Vdc, 1.2 A WAN Interface Tributary Slots 2 ports Cold-swappable Plug-in card types: E1 card: 2 ports per card, Nx64k T1 card: 2 ports per card, Nx64k Ethernet card: 1 port per card, electrical RJ45 Ethernet card: 1 port per card, optical SFP Built-in 2 Ethernet ports Multiple WANs per fractional E1/T1 interface is supported, up to 64 WAN per system (maximum 16 WAN supports PPP encapsulation) LAN Interface 4 Ethernet ports All Ethernet Interfaces 10/100BaseT Speed and duplex-mode auto-negotiation Auto MDI/MDI-X cross-over Layer 3 IPv4/IPv6 dual stack Routing Protocols: Static Route, RIPv1/v2, RIPng, OSPFv2/v3, BGP4. Multicast protocols: IGMPv1/v2/v3 VLAN Routing based on Static Route, RIPv1/v2, RIPng, OSPFv2/v3. Address Translation NAT Port Forwarding Table for NAPT (Virtual Service) IP-VPN connectivity over IPSec Security IPSec Encryption: DES, 3-DES, AES-128/AES-256 Authentication: MD5, SHA-1 Key Management Up to 64 concurrent tunnels per interface IP-VPN connectivity over IPSec Access Control Packet-Filtering based on policy type: IKEv1/v2 (pre-shared key or RSA certificate) Inbound/Outbound direction Source/Destination IP Address Range Any Protocol Types (ICMP, TCP, UDP, etc.) TCP/UDP Port Number Range 1 control list per interface Up to 100 rules per control list 802.1x port-based authentication* Multilevel login privilege control Radius Client is supported, up to 3 Radius servers available for addressing. SSHv1/v2 SNMPv3 1

2 Layer 2 Encapsulation Protocols PPP, MLPPP, Cisco HDLC, raw HDLC Management Telnet and SSHv1/v2 (up to 4 concurrent sessions) SNMPv3 Multilevel login privilege control Syslog NTP Client for IPv4, up to 4 NTP server QoS Policy based Egress Rate Limiting Traffic Classification based on Outbound direction IPv4 or IPv6 Source/Destination IP Address Range TCP/UDP Port Number (DSCP+ENC) 1byte field / ToS 1 byte field Any Protocol Type DHCP DHCP Server/Relay for IPv4/IPv6 BOOTP compatible for IPv4 Software Bridging* Frame size up to 1916 bytes* IEEE 802.2x Flow Control* STP(802.1d) *, RSTP(802.1w) *, MSTP(802.1s) * Up to 16K MAC Table* User-configurable MAC aging time* Ethernet FCS padding/unpadding* 802.1x port-based authentication* VLAN* Support up to 4094 VLANs* VLAN ID mapping* Support Q-in-Q * Support VLAN Routing* * Future option Ordering Information To specify options, please choose from the list below. Note: RoHS compliant units are identified by the letter G appearing at the end of the ordering code. Model Description Notes Main Unit Loop-IP6510-LN-aa-bb-pp-RT-G 1U height ETSI (front access) unit, stand-alone with two built-in 10/100BaseT WAN interfaces and four 10/100BaseT LAN interfaces, which supports Router functionality Where aa, bb and pp modules are defined in the tables below Additional Cold Plug-in Modules Loop-IP6510-LN-2T1-G Dual T1 interface with RJ48C connector Loop-IP6510-LN-2E120-G Dual E1-120 ohm interface with RJ48C E1-120 ohm/t1 jumper selectable connector Loop-IP6510-LN-1FE-G One 10/100 BaseT Fast Ethernet, RJ45 electrical port Loop-IP6510-LN-SFPH-G SFP (mini-gbic) housing for 100M-FX SFP optical modules not included SFP Optical Modules SFP (small form-factor pluggable) optical modules are NOT included. To order please check the SFP optical module brochure or contact your nearest Loop sales representative. Accessories Power Cord (All power cords are RoHS compliant) Loop-ACC-PC-USA AC power cord for Taiwan/America Loop-ACC-PC-EU Loop-ACC-PC-UK AC power cord for Europe AC power cord for UK 2

3 Loop-ACC-PC-AUS Loop-ACC-PC-CH AC power cord for Australia AC power cord for China Ear Mounts A00LF A00LF User s Manual Loop-IP6510-LN-UM Firmware Upgrade Loop-IP6510-LN-FWUPGR A pair of 19 ear mounts A pair of ear brackets for wall mount User s Manual (optional, printed on paper copy). A CD version of the manual is already included as standard equipment. Firmware Upgrade. Customers who desire to have a firmware upgrade after their warranty has expired can purchase this option. This will upgrade the firmware to the most current version and provide an additional 12 months of software repair and patches on existing functionality as necessary. Replace the fields aa and bb with the cold plug-in modules desired. If such modules are not required, then please omit the aa or bb field in the ordering code. aa, bb = Description Notes 2T1 Dual T1 interface with RJ48C connector E1-120 ohm/t1 jumper selectable 2E120 Dual E1-120 ohm interface with RJ48C connector 1FE One 10/100 BaseT Fast Ethernet Replace the field pp with your selection of a power supply. pp = Description Notes P9 Hybrid 100 to 240 Vac and -48 Vdc (-36 to -72 Vdc) coexist fixed For AC, choose an appropriate power supply power cord. Loop-IP6510-LN Product Specifications Ethernet WAN Interface Two built-in 10/100BaseT Ethernet ports (WAN1 and WAN2) Speed auto-sensing Half / full duplex auto-negotiation Auto MDI/MDI-X crossover WAN Plug-in Modules E1 card: 2 ports per card, up to 4 ports per system T1 card: 2 ports per card, up to 4 ports per system Electrical Ethernet card: 1 port per card, up to 2 ports per system Optical Ethernet card: 1 port per card, up to 2 ports per system Layer 2 E1/T1 WAN protocols: PPP, MLPPP, HDLC, Cisco compatible HDLC E1 Line Interface Line Rate Mbps ± 50 ppm Line Code HDB3 Output Signal ITU G.703 Connector RJ48C Loopbacks Line Loopback, Payload Loopback Test Pattern 20-bit QRSS, 3-in-24, 1-in-8, 2-in-8, 1:1 T1 Line Interface Line Rate Line Code Output Signal Mbps ± 50 bps AMI or B8ZS DS1 3

4 Connector RJ48C Loopbacks Line Loopback, Payload Loopback Test Pattern 20-bit QRSS, 3-in-24, 1-in-8, 2-in-8, 1:1 SFP Optical Ethernet WAN Interface Speed 100 Base-FX Full Duplex Mode Supported Automatic Laser Shut Down Supported Switch L2 Switch not supported Temperature Range -20C to +65C TDM WAN Interface One WAN per Fractional E1/T1 port, Up to 4 WANs per system Configurable Nx64K per WAN. Multiple WAN per Fractional E1/T1 port, up to 64 WANs per system LAN Interface Four 10/100BaseT interfaces Speed auto-sensing Half / full duplex auto-negotiation Auto MDI/MDI-X crossover Management and Administration Console Port Electrical: RS232 CLI management via console port Remote Login Telnet, SSH SNMP SNMP v1, v2 and v3 Diagnostics Ping, Traceroute, Loopback Router Supports IPv4 and IPv6 Routing protocol: RIP v1, RIP v2, RIPng, OSPF v2, OSPF v3, and BGP4 Multicast Protocol: IGMP, MLD*, IPv4 PIM-SM/DM, IPv6 PIM-SM/DM* VLAN routing L2 Protocol: PPP, MLPPP, Cisco HDLC, Raw HDLC Address Translation NAT / NAPT Static address table for NAT Port forwarding table for NAPT (Virtual Service) DHCP DHCP server support for LAN users (RFC 2131, RFC 2132) BOOTP compatible DHCP relay DHCP client Access Control & Firewall Packet filtering based on Source/destination IP address Protocol types (ICMP, TCP, UDP) Source/destination port number (UDP or TCP) QoS QoS based on rate limit Classification based on Source/destination IP address Protocol types (ICMP, TCP, UDP) Source/destination port number (UDP or TCP) IPSec VPN Encryption Authentication Key Management Tunnels DES, 3DES, AES MD5, SHA-1 Manual Key, IKEv2 Up to 64 concurrent tunnels per interface 4

5 Electrical Power Source (AC) Power Source (DC) Power Consumption 100 to 240 Vac, 0.8 A -36 to -72 Vdc, 1.2 A < 20 W Physical and Environment Dimensions x 44 x mm (W x H x D) Mounting Stand-alone, wall mount Temperature Range 0 C to 55 C Humidity 0% - 95% RH (non-condensing) Standards Compliance IEEE 802.1q VLAN, 802.3u IETF RIP1 (RFC 1058), RIP2 (RFC 1389), OSPFv2 (RFC 2328), OSPFv3 (RFC 5340), BGP (RFC 4271) ITU G.703, G.704, G.823 Compliance EMC/EMI Safety FCC15 Class A, EN55022, EN55024 IEC (CB) * Future option Front Panel View 5

6 Application Illustrations (up to 4 E1/T1 links) MLPPP Bundle LAN LAN IP6510-LN IP6510-LN Multilink PPP IPv4 and IPv6 Interworking LOOP TELECOMMUNICATION INTERNATIONAL, INC. LoopTelecom.com ISO 9001 / ISO Worldwide Taipei, Taiwan North America Tianjin, China 8F, No. 8, Hsin Ann Road 6F, No. 36, Alley 38, Lane Carrick Road No. 240 Baidi Road Hsinchu Science Park Rueiguang Road Palm Beach Gardens Nankai District Hsinchu, Taiwan Neihu, Taiwan Florida 33418, U.S.A. Tianjin China michael_tzeng@loop.com.tw jimber561@aol.com wym@loop-tj.com sales@loop.com.tw 2013 Loop Telecommunication International, Inc. All Rights Reserved Version 8 10 September 2013 Subject to change without notice 6