Loop-O9150S SDH STM-1 TM/ADM

Transcription

1 Loop-S SDH STM-1 TM/ADM Description Features 1U height, ETSI shelf (full front access) or ANSI shelf (front and rear access) SDH STM-1TM/ADM Aggregate port 2 SFP optical housing MSP 1+1 protection SNCP protection Tributary port (manufacturing option) Two 8-port ports with DB37 connector or 16-port ports with RJ48C and four 10/100 (FE) ports 8-port with RJ48C connector and 8-port with DB37 connector, with four 10/100 (FE) ports 8-port ports with RJ48C /DB37and two 10/100 (FE) ports 4-port ports with RJ48C/DB37and two 10/100 (FE) ports Hot swappable power Modules, dual power modules for redundancy DC power -48 Vdc (-36 to -72Vdc) AC power (100 to 240 Vac) Networking protection MSP (1+1) protection for TM(Terminal Multiplexer) SNCP protection for ADM (Add/Drop Mux) VC-12 cross-connect 4- Port for total 63xVC12, with independent port configuration Supports Internal/Line clock Supports VCAT, GFP, and LCAS Supports E-Line Performance monitoring Alarm suppression, masking, and reporting Management: Console port SNMP port Centralized management with Loop s EMS over DCC channel LoopView GUI EMS Telnet support RoHS compliant The Loop-S SDH STM1 TM/ADM is a standard equipment device for SDH/MSTP networks with VC-12 directly reaching the network terminal. Through an STM-1 uplink, the S provides VC-12 standard s and supporting VCAT, GFP, and LCAS protocol. The S is a comprehensive fiber transmission platform for traditional telecom business and broadband information business applications. As well, it is suited to adapt to general data in Metropolitan Area Networks and audio and information business data in Private Networks. On the aggregate side, the S has two STM-1 ports supporting MSP (1+1) TM and SNCP for ADM protection. On the tributary side, the S has four s and up to two 8-port. As terminal equipment, the S can be built in a range of complex topologies such as star, linear and ring. These can support a non-blocking cross-connect between different business interfaces. All interfaces are fully compliant with the relevant ANSI standards and ITU recommendations. The S provides fault management, performance monitoring, configuration management, and network security management. Through the console port, LAN port and DCC channel, the OAM&P can be achieved both locally and remotely via SNMP or menu-driven interfaces. S supports the LoopView GUI EMS (Element Management System). 1

2 Ordering Information To specify options, choose from the list below: Note: RoHS compliant units are identified by the letter G appearing at the end of the ordering code. Model Description Notes housing, 16 port (75 ohm) with DB37 male connector, and 4 ports, DB37 female to 1.0/2.3 RF conversion adaptor included Loop--S-16EDB75-4FEpp1-pp2-G Where pp1, pp2, opt modules are defined in the table below. Loop--S-16ERJ-4FE-pp 1-pp2-G Loop--S-16EDB120-4F E-pp1-pp2-G Loop--S-8ERJ-8EDB75-4FE-pp1-pp2-G Loop--S-8ERJ-2FEpp1-pp2-G Loop--S-8EDB75-2FEpp1-pp2-G Loop--S-8EDB120-2FEpp1-pp2-G Loop--S-4ERJ-2FE-pp1 -pp2-g Loop--S-4EDB75-2FEpp1-pp2-G Loop--S-4EDB120-2FEpp1-pp2-G housing, 16 port (120 ohm) with RJ48C connectors, and 4 ports housing, 16 port (120 ohm) with DB37 male connector, and 4 ports, conversion cable not included housing, 8 port with RJ48C connectors and 8 port (75 ohm) with DB37 male connector, and 4 ports, DB37 female to 1.0/2.3 RF conversion adaptor included housing, 8 port (120 ohm) with RJ48C connectors, and 2 ports. housing, 8 port (75 ohm) with DB37 male connector, and 2 ports, DB37 female to 1.0/2.3 RF conversion adaptor included housing, 8 port (120 ohm) with DB37 male connector, and 2 ports, conversion cable not included housing, 4 port (120 ohm) with RJ48C connectors, and 2 ports. housing, 4 port (75 ohm) with DB37 male connector, and 2 ports, DB37 female to 1.0/2.3 RF conversion adaptor included housing, 4 port (120 ohm) with DB37 male connector, and 2 ports, conversion cable not included Order SFP modules separately from SFP module plug-in table below. Accessories User s Manual Loop--S-UM Paper copy of User Manual. Note: Standard package includes CD version SFP Optical Modules Please place your order using the 5-digit alphanumeric codes listed in the separate SFP Optical Module Brochure. Power Cord Loop-ACC-PC-USA AC power cord for Taiwan/America Loop-ACC-PC-EU AC power cord for Europe Loop-ACC-PC-UK AC power cord for UK Loop-ACC-PC-AUS AC power cord for Australia Loop-ACC-PC-CH AC power cord for China 2

3 Conversion Connector Loop-ACC-COV-1DB37F-8RF75 Blank Panel A00LF-G A00LF-G One DB37 female to eight (8TX/8RX) 1.0/2.3 RF male (75ohm impedance) conversion adaptor Blank panel for single DC power slot Blank panel for single AC power slot SFP module plug-in table (Please place your order using the 5-digit alphanumeric codes listed below) Order Code Description Notes PHB2W Singe-mode optical module with dual uni-directional fiber, Mbps 155Mbps, 1310nm, 20Km, LC connector 2. Dual uni-directional Fiber PHB4W Singe-mode optical module with dual uni-directional fiber, 155Mbps, 1310nm, 40Km, LC connector 3. Commercial(0 to 70 C) PHB6W Singe-mode optical module with dual uni-directional fiber, 155Mbps, 1310nm, 60Km, LC connector PHC8W Singe-mode optical module with dual uni-directional fiber, 155Mbps, 1550nm, 80Km, LC connector PHCUW Singe-mode optical module with dual uni-directional fiber, 155Mbps, 1550nm, 100Km, LC connector PHCXW Singe-mode optical module with dual uni-directional fiber, 155Mbps, 1550nm, 120Km, LC connector PHB2D Singe-mode optical module with dual uni-directional fiber, 155Mbps, 1310nm, 20Km, LC connector with PHB4D Singe-mode optical module with dual uni-directional fiber, 155Mbps, 1310nm, 40Km, LC connector with PHB6D Singe-mode optical module with dual uni-directional fiber, 155Mbps, 1310nm, 60Km, LC connector with PHC8D Singe-mode optical module with dual uni-directional fiber, 155Mbps, 1550nm, 80Km, LC connector with PHCUD Singe-mode optical module with dual uni-directional fiber, 155Mbps, 1550nm, 100Km, LC connector with PHCXD Singe-mode optical module with dual uni-directional fiber, 155Mbps, 1550nm, 120Km, LC connector with PHD2W Mbps 155Mbps, TX1310nm/RX1550nm, 20Km, LC Connector 2. Single Bi-directional Fiber PHE2W 3. Commercial(0 to 70 C) 155Mbps, TX1550nm/RX1310nm, 20Km, LC Connector 4. Wavelength Pairing PHD4W 1) D(TX1310nm/RX1550nm) pairs 155Mbps, TX1310nm/RX1550nm, 40Km, LC Connector E(TX1550nm/RX1310nm) PHE4W 2) Q(TX1490nm/RX1550nm) pairs 155Mbps, TX1550nm/RX1310nm, 40Km, LC Connector R(TX155onm/RX1490nm) PHD6W 155Mbps, TX1310nm/RX1550nm, 60Km, LC Connector PHE6W 155Mbps, TX1550nm/RX1310nm, 60Km, LC Connector PHD8W 155Mbps, TX1310nm/RX1550nm, 80Km, LC Connector PHE8W 155Mbps, TX1550nm/RX1310nm, 80Km, LC Connector PHQUW 155Mbps, TX1490nm/RX1550nm, 100Km, LC Connector PHRUW 155Mbps, TX1550nm/RX1490nm, 100Km, LC Connector PHQXW 155Mbps, TX1490nm/RX1550nm, 120Km, LC Connector PHRXW 155Mbps, TX1550nm/RX1490nm, 120Km, LC Connector PHD2D 155Mbps, TX1310nm/RX1550nm, 20Km, LC Connector with PHE2D 155Mbps, TX1310nm/RX1550nm, 20Km, LC Connector with 3

4 PHD4D PHE4D PHD6D PHE6D PHD8D PHE8D PHQUD PHRUD PHQXD PHRXD 155Mbps, TX1310nm/RX1550nm, 40Km, LC Connector with 155Mbps, TX1550nm/RX1310nm, 40Km, LC Connector with 155Mbps, TX1310nm/RX1550nm, 60Km, LC Connector with 155Mbps, TX1550nm/RX1310nm, 60Km, LC Connector with 155Mbps, TX1310nm/RX1550nm, 80Km, LC Connector with 155Mbps, TX1550nm/RX1310nm, 80Km, LC Connector with 155Mbps, TX1490nm/RX1550nm, 100Km, LC Connector with 155Mbps, TX1550nm/RX1490nm, 100Km, LC Connector with 155Mbps, TX1490nm/RX1550nm, 120Km, LC Connector with 155Mbps, TX1550nm/RX1490nm, 120Km, LC Connector with Where pp1 is used to select 1 st power module. pp1= Description Notes SD48 Single DC pluggable power module (-48Vdc, -36 to All plug-in power modules are -72Vdc ) interchangeable SA Single AC power modules (100 to 240 Vac) For AC, please choose an appropriate power cord AC power module Where pp2 is used to select 2 nd power module. pp2= Description Notes SD48 Single DC pluggable power module (-48Vdc, -36 to For redundancy purpose, ordering -72Vdc ) supply second plug-in power module SA Single AC power modules (100 to 240 Vac) You can not order a second SA for ETSI unit. Available in ANSI shelf when pp1 = SD48, pp2=sa (One SD48 in front and one SA at rear) For AC, please choose an appropriate power cord AC power module Note: The combination of pp1 and pp2 power modules: For ETSI unit (all power modules in front) pp1=sd48 (single DC power plug-in) pp1=sa (single AC power plug-in) pp1=sd48, pp2=sd48 (dual DC power plug-in) For ANSI unit (one power module in front, one power module at rear)* pp1=sd48 (single DC power plug-in at rear) pp1=sa (single AC power plug-in in front or at rear) pp1=sa, pp2=sa (single AC in front, single AC at rear) pp1=sd48, pp2=sd48 (dual DC power plug-in at rear) pp1=sd48, pp2=sa (One SD48 in front and one SA at rear) 4

5 Loop-S Product Specifications SFP Daughter Card Modules (refer to SFP optical brochure for detail) Aggregate Lines Interface Number of DB37 connector: 2 * 8 /per port RJ48C connector: 16 DB37 connector: 1 * 8 / per port RJ48C connector: 8 DB37 connector: 1 * 4 / per port RJ48C connector: 4 Line Rate M bps ± 50 ppm Output Mask ETS Sec ITU G.703 Line Code HDB3 Jitter ITU G.823 Input Code ITU G.703 Framing unframed Output Code ITU G.703 Impedance 75 ohm coax/120 ohm twisted pair Connector 1. DB37 (75ohm) male with conversion connector 2. DB37 (120ohm) male 3. RJ48C Fast (FE) Interface Number of Port 4 or 2 Line Rate bps Mapping n x VC12 Process Protocol VCAT, GFP(G.7041), and LCAS (G.7042) Connector RJ45 Frame MTU System Clock Clock Source Management LEDs Console Port Telnet SNMP Outband Interface Diagnostics System Loopback Test 1792 bytes Internal Cock Two Line Clock Multi-color LEDs Electrical: RS232 Connector: RJ45 (female, DCE) Protocol: Menu driven VT-100 SNMPv1 (RFC1213) Using DCC channel, user selectable 3, 9 or 12 channels Direction: to optical lines, to tributary lines Unit Loopback Test Direction: to optical lines, to tributary lines BERT Test interface Direction: to optical lines, to tributary lines Unit Lane Loopback Test Wan Loopback Test Wan-to-Wan Loopback Test Direction: to optical lines Direction: to optical lines, to tributary lines Direction: to tributary lines Performance Monitor Performance Reports Performance Parameters: Error Block (EB), Background Block Error (BBE), Error Second (ES), Burst Error Second (BES), Severe Error Second (SES), Unavailable Second (UAS) Alarm History System Alarm Power Loss, TS Sync Loss, SNCP Switch, MSP Switch, Login/Logout, FOM Equip/Unequip SDH Line Alarm SDH Line PI-LOS, RS-LOF, RS-TIM, RS-BIP UAS, MS-SD, MS-SF, MS-AIS, MS-RDI, MS-BIP UAS, MS-REI UAS, Ho-Path AU-LOP, AU-AIS, HP-TIM, HP-UNEQ, HP-PLM, HP-RDI-S, HP-RDI-C, HP-RDI-P, HP-BIP 5

6 UAS, HP-REI UAS, LOM Lo-Path TU-LOP, TU-AIS, LP-UNEQ Alarm Queue Power AC Power DC Power Power Consumption Contains up to 300 alarm records of latest alarm types, alarm severity, date and time. 100 to 240 Vac, 50/60Hz -48 Vdc (-36 to -72Vdc) Maximum 25 Watts Physical Dimensions 480 x 44 x 220 mm. (W x H x D) Temperature 0 to 50 C Humidity 0-95%RH (non-condensing) Mounting Desk-top, 19-inch rack mountable, and wall mountable Standards Compliance ITU G.664, G.707, G.7041, G.7042, G.775, G.783, G.806, G.823, G.747, X.86 ANSI T1.105, T1.107 IEEE 802.1q (VLAN), 802.1w (RSTP), 802.1s (MSTP) 802.3x (flow control) IETF RFC2236 (IGMP Snooping), RFC1213 (SNMPv1) Certification EMI/EMC Safety EN55022 Class A, EN55024, EN , EN EN Application Illustrations TM (MSP Protection) STM-1 Ring 6

7 ADM STM-1 Ring LOOP TELECOMMUNICATION INTERNATIONAL, INC. LoopTelecom.com ISO 9001 / ISO Worldwide Taipei, Taiwan North America Tianjin, China 8F, No. 8, Hsin Ann Road 6F, No. 36, Alley 38, Lane Carrick Road No. 240 Baidi Road Hsinchu Science Park Rueiguang Road Palm Beach Gardens Nankai District Hsinchu, Taiwan Neihu, Taiwan Florida 33418, U.S.A. Tianjin China michael_tzeng@loop.com.tw jimber561@aol.com wym@loop-tj.com sales@loop.com.tw 2013 Loop Telecommunication International, Inc. All Rights Reserved Version 5 August Subject to change without notice 7