Loop-IP6750 Service Aggregation & Access Device

Transcription

1 Loop-IP6750 Service Aggregation & Access Device ANSI Front View ETSI Front View Description The Loop-IP6750 Service Aggregation & Access Device is an effective way for service providers to build their network and achieve a fast return on investment. Currently providers need to transport both TDM and Packet traffic. These can be achieved using the E1/T1 and Gigabit Ethernet tributary ports of the IP6750. In addition to working now, service providers also have to build the network to meet future requirements. The IP6750 can handle temperature ranges of 0 to 65 C. It supports many protocols such as MEF-8 CESoETH, SyncE and IEEE1588v2 Precision Timing, G.8031 Ethernet Linear Protection Switching, and a RFC2544 built-in traffic generator. The IP6750 s durability and capabilities make it an important device for your network to meet the requirements of a carrier-grade Service Level Agreement (SLA). Product Features Mechanical and Electrical 1U height, 19 width ANSI/ETSI Power module AC/DC dual feed slots Hot swappable Temperature range from 0 to 65 C WAN Aggregate Interface 2 GbE ports with SFP housing IEEE 802.3ad Ethernet Link Aggregation G.8032 v1/v2 Ethernet Ring Protection Switching (ERPS)* G.8031 Ethernet Linear Protection Switching (ELPS) Compliant with MEF 8, 9 and 14. Timing Internal/Line External BITS I/O with RJ connector: 2 Mbps, 2 MHz, 1.544Mbps composite clock Adaptive Clock Recovery (ACR) and Differential Clock Recovery (DCR) for TDM Pseudowires Jitter and Wander conforms to MEF 18, ITU-T G.8261, and G.823/824 for Traffic Interface SNTPv4 Tributary Interface 4 hot-swappable slots for the following cards: CGbE: Combo Gigabit Ethernet card 2 port groups per card, (1 SFP optical, 1 electric) up to 8 port groups per system E1 / T1 card 4 ports per card, up to 16 ports per system E1/T1 software configurable per card OAM Ethernet OAM 802.1ag / Y ah Syslog and Dying Gasp alarm QoS Ingress Rate Limiting per port Ethernet Network Level 3-bit Priority Code Point PCP field within 802.1p / 802.1q Ethernet frames CoS 8 priority queues per port IP Network Level 6-bit DiffServ Code Point DSCP field ToS Scheduling Algorithms 1

2 SyncE (ITUT-G.8261) GE interfaces IEEE 1588v2 slave/boundary/transparent clock Internal stratum 3 clock (hold-over state) TOD interface 1PPS interface L2 Switching 5G non-blocking switching capacity Jumbo frame size up to 10K bytes Maximum 4K VLANs 802.1d MAC Table Learning (maximum 32K) 802.3x Flow Control on input ports 802.1d STP, 802.1w RSTP, 802.1s MSTP* IGMP Snooping v2 RFC 2236 and v3 RFC4604* Management SNMPv1/v2c/v3 CLI command line interface Telnet and SSHv1/v x (port access protocol)* RADIUS Client Strict Priority (SP) Weighted Round Robin (WRR) Congestion Avoidance Weighted Random Early Detection (WRED)* Policing algorithm Two-Rate Three-Color Token Bucket Pseudowires TDM Pseudowires Up to 64 concurrent pseudowires Pseudowire protocols SAToP CESoPSN MEF-8 (CESoETH) Packet Delay Variation Compensation Depth up to 256 ms Diagnostics Built-in traffic generator to support RFC2544/Y.1564 and Y.1731 testing E1/T1 BERT & Loopback Ethernet loopback * Future option 2

3 Ordering Information Note: RoHS compliant units are identified by the letter G appearing at the end of the ordering code. Main Unit Name Description Notes Loop-IP6750-IE-aa-bb-cc -dd-pp1-pp2-add2-g Loop-IP6750-IA-aa-bb-cc -dd-pp1-pp2-add1-add2- G Loop-IP6750 Plug-in Modules (aa, bb, cc, dd) 4IETDB37 2ICGbEC 1U height ETSI chassis (full frontal access) with 2 GbE SFP aggregation ports, Console RS232 port, and SNMP RJ45 port. Replace the aa, bb, cc, dd, pp1, pp2, add1, and add2 fields with your selection from the choices below. If not needed then leave field blank. 1U height ANSI chassis (front and rear access) with 2 GbE SFP aggregation ports, Console RS232 port, and SNMP RJ45 port. Four E1/T1 ports with single DB37 interface (E1-120 ohms, E1-75 ohms, T1, software selectable per card) SFP optical modules are ordered Combo GE/FE card with two port groups one SFP interface and one RJ45 interface per port group separately. Consult the SFP Optical Modules Brochure. Power Supply (pp1, pp2) ISD48 Single DC power plug-in module at -48 Vdc (-42 to -56 For redundancy purposes, order a Vdc) second power module for dual backup ISA Single AC power plug-in module (110 to 240 Vac at 50 power. Dual AC power is only available to 60 Hz) on ANSI chassis. Additional Options I (add1) LCD LCD front panel display LCD front panel is for ANSI chassis only. LCD only supports temperature range 0 to 50 C (32 F to 122 F) Additional Options II (add2) EXT 1588 EXT1588 External Clock Input Port and Output Port (2 RJ45 ports) and 1PPS physical connector 1PPS clock output, ToD (Time of Day) output, and full software capability from IEEE 1588v2. External Clock Input Port and Output Port. (2 RJ45 ports). 1PPS clock output, ToD (Time of Day) output, and full capability from IEEE 1588v2. Upgrading from EXT to EXT1588 is available via software upgrade at a later time. See accessories section below. EXT1588 contains the IEEE 1588v2 software upgrade already pre-installed. Separate Plug-in Modules Loop-IP6750-4IETDB37- G Loop-IP6750-2ICGbEC- G Four E1/T1 ports with single DB37 interface (E1-120 ohms, E1-75 ohms, T1, software selectable per card) Combo GE/FE card with two port groups one SFP interface and one RJ45 interface per port group Separate Power Supplies Loop-IP6750-ISD48-G Single DC power plug-in module at -48 Vdc (-42 to -56 Vdc) Loop-IP6750-ISA-G Single AC power plug-in module (110 to 240 Vac at 50 to 60 Hz) Accessories Conversion Cable (All conversion cables are RoHS compliant) Cards are the same as shown in the Main Unit section above. Use this ordering code if you are ordering backup or additional cards. SFP optical modules are ordered separately. Power modules are the same as shown in the Main Unit section above. Use this ordering code if you are ordering backup or additional power modules. 3

4 Loop-ACC-COV-DB37M-WW-04 Loop-ACC-CAB-DB37M-100-4RJ48F-GND Loop-ACC-CAB-DB37M-100-8BNCM-GND* Loop-ACC-CAB-DB37M-100-8BNCF-GND* Loop-ACC-CAB-BNCM-100-RF75M* * Future option Power Cord (All power cords are RoHS compliant) DB37 male to 4 ports wire-wrap conversion adaptor DB37 male to 4RJ48 female ground conversion cable. Length: 100 cm DB37 male to 8BNC (4 ports) male ground conversion cable. Length:100 cm DB37 male to 8BNC (4 ports) female ground conversion cable. Length:100 cm BNC Male to 1.0/2.3 RF connector (75 ohm impedance) male ground conversion cable (Length: 100 cm) (future option) Loop-ACC-PC-USA Loop-ACC-PC-EU Loop-ACC-PC-UK Loop-ACC-PC-AUS Loop-ACC-PC-CH AC power cord for Taiwan/America AC power cord for Europe AC power cord for UK AC power cord for Australia AC power cord for China Blank Panels Blank panel for empty AC power slot Blank panel for empty DC power slot Blank panel for empty plug in module slot 1, 2, 3, or 4 User s Manual User s Manual (optional, paper printed copy). A electronic version of the manual on a CD is Loop-IP6750-UM included with every order. SFP Optical Modules SFP (small form-factor pluggable) optical modules are NOT included. To order please check the SFP optical module brochure or contact your Loop sales representative. Ear Mounts 19 /23 ear mounts A pair of 19 /23 ear mounts is supplied as part of the standard package. For other sizes please contact your Loop sales representative. Firmware Upgrade Firmware Upgrade. Customers who desire to have a firmware upgrade after their warranty has expired can purchase this option. This will upgrade the firmware to the most current version Loop-IP6750-FWUPGR and provide an additional 12 months of software repair and patches on existing functionality as necessary. IEEE 1588v2 PTP Software Upgrade Software Upgrade to IEEE 1588v2. Customers who desire to use the IEEE 1588 v2 Precision Time Protocol (PTP) function can purchase this option. This option will provide an activation Loop-IP UPGR code and instructions on how to unlock the function on the device. This software option can only be purchased if the External Clock (EXT) is already equipped on the unit. The EXT1588 additional option already has this upgrade installed. Ordering Examples Loop-IP6750-IE-4IETDB37-4IETDB37-4IETDB37-4IETDB37-ISD48-ISD48-EXT1588-G Loop-ACC-PC-EU Loop IP6750 main unit with ETSI front chassis, industrial temperature range. 4 E1/T1 plug in cards, a total of 16 E1/T1 ports on the unit. Dual DC power of -48 Vdc. External clock with 2 RJ45 input and output ports. IEEE 1588v2 software upgrade pre-installed. RoHS compliant. AC power cord for Europe. Loop-IP6750-IA-2ICGbEC-2ICGbEC-4IETDB37-4IETDB37-ISA-ISA-LCD-EXT-G Loop-ACC-PC-USA Loop IP6750 main unit with ANSI front chassis, industrial temperature range. 2 Combo Gigabit Ethernet cards and 2 E1/T1 cards. A total of four SFP ports, four RJ45 ports, and eight E1/T1 ports on the unit. Dual AC power. LCD front panel included. External clock with 2 RJ45 input and output ports included. RoHS compliant. AC power cord for America 4

5 Loop-IP6750 Product Specification E1 Tributary Interface Card (E1/T1 software selectable) Line Rate Mbps ± 50 ppm Line Code HDB3 Framing ITU G.704 (CRC: on/off, CAS: on/off, unframed) Output Signal ITU G.703 Input Signal ITU G.703 Jitter ITU G.823 Connector DB37 T1 Tributary Interface Card (E1/T1 software selectable) Line Rate Mbps ± 32 ppm Line Code AMI / B8ZS (selectable) Framing D4 / ESF/ ESF&T1.403/ OFF (unframed) Output Signal DS1 with LBO Setting Input Signal DS1 Pulse Template Per AT&T TR Connector DB37 Combo GE/FE Interface Card Number of Ports per Card Speed 4 physical ports 2 port groups with 1 RJ45 and 1 SFP port per port group 10/100/1000 BaseT Gigabit Ethernet Aggregation Ports Number of Ports 2 Connector SFP Speed 1000-LX SNMP Ethernet Ethernet Functions Connector Alarm Relay Alarm Relay System Clock Clock Source 10/100 BaseT, IEEE802.3 Auto-negotiation (10/100M) Auto MDI/MDIX Full or half duplex RJ45 Fuse alarm and performance alarm Internal clock E1/T1 line clock Sync Ethernet 1588V2 Ethernet Management and Administration Management ports Console RS232 port and and NMS RJ45 port CLI Fully manageable with CLI (command line interface) Remote login SSHv1 and v2, Telnet SNMP SNMP v1, v2c, v3 Dying Gasp Alarm Supported Web HTTP, HTTPS (TLS 1.0, TLS1.1 and TLS 1.2) Electrical DC Power Module AC Power Module Power Consumption Physical and Environmental Dimensions Net Weight Temperature Humidity 48 V (-36 to -72 Vdc), 24 Vdc (-18 to -36 Vdc) Second DC module is hot swappable 100 to 240 Vac, 50 to 60 Hz < 65 W for 1U height 438 mm x 44 mm x 300 mm (width x height x depth) 4.0 Kg 0 C to +65 C 0% to 95% RH (non-condensing) 5

6 Mounting Cooling Desktop stackable, rack mount, wall mount Built in fan unit Standards Compliance IEEE IETF 802.1d MAC Table Learning and STP RFC2236 IGMP Snooping v2* 802.1p Priority Code Point RFC2544 Benchmark Testing for Network 802.1q VLAN Interconnect Devices 802.1s MSTP* RFC 4604 IGMP Snooping v3* 802.1w RSTP* RFC 4553 SAToP 802.1x Port Access Protocol* 802.1ad Tag Stacking (Q-in-Q) ITU 802.1ag Ethernet CFM G.823/G.824 Traffic and Synchronous Interface 802.3x Flow Control G.8032 v1/v2 Ethernet Ring Protection Switching (ERPS)* G.8031 Ethernet Linear Protection Switching (ELPS) 802.3ad Link Aggregation G.8261 SyncE GE Interfaces 802.3ah Ethernet in the First Mile Y.1564 Ethernet SLA Validation Testing 1588 v2 Precision Time Protocol Y.1731 OAM 1613 Environmental Testing for Power Substations MEF 8 CESoETH 9 14 Certifications EMC/EMI EN55022, EN50024, EN IEEE 1613 Environmental Testing in Electric Power Substations* IEC *, Safety EN , IEC60950, UL60950 MEF Panel Views MEF 9 & 14 CE1.0 * Future Option ANSI Front Panel View with Single AC Power and LCD Display 6

7 Loop-IP6750 Service Aggregation & Access Device ETSI Front Panel View with Single AC Power, 2 Combo Gigabit Ethernet Cards, and 2 E1/T1 Cards Application Illustrations IP A g g r e g a tio n P r o te c tio n P a ir 16 E1/T1 o r 8 G b E IP E1/T1 o r 8 G b E Point to Point Application Multistage Multiplexer Application 7

8 Single Stage Multiplexer Application Metro Ethernet Application 8

9 Worldwide Europe America LOOP TELECOMMUNICATION INTERNATIONAL, INC. ISO 9001 / ISO Australia & New Zealand 6F, No. 8, Hsin Ann Road Rue de Culot, 13 8 Carrick Road 3 Imperial Ave, Mount Hsinchu Science Park BE-1402 Nivelles Palm Beach Gardens Waverley, Victoria 3149, Hsinchu, Taiwan Belgique Florida 33418, U.S.A. Australia sales@looptelecom.com eu_sales@looptelecom.com ncsa_sales@looptelecom.com aus_sales@looptelecom.com 2017 Loop Telecommunication International, Inc. All Rights Reserved Version 1 28th April 2017 Subject to change without notice 9