User Manual. 1000Base-T1 Standard Ethernet 1000Base- T1_SPY_mini. Version 0.3 October 2017

Transcription

1 1000Base-T1 Standard Ethernet 1000Base- T1_SPY_mini User Manual Version 0.3 October 2017 Technica Engineering GmbH Leopoldstr München Web:

2 Page 2 of 24

3 Index 1 Feature List Warranty and Safety Information Pinning Power and 1000Base-T1 connector SubD 9 Trigger Connector RJ45 Ethernet connectors Status LEDs Configuration Use Cases Dual Media Converter Mode Spy Mode Independient Spy Mode 2 in Spy Mode Independent with Wrapper Base-T1 SPY mini LUA dissector Trigger Functions Frequently Asked Questions FAQ Contact...24 Page 3 of 24

4 1 Feature List The Technica Engineering 1000Base-T1 SPY mini samples 1000Base-T1 Frames directly on the bus without influence of the original network. The data Frames are enhanced with additional information as an exact timestamp and the bus port which the data was originally sent on. All data can be recorded on a PC or datalogger for detailed offline analysis. Timestamps are in 0.04 μs resolution and synchronous to all connected lines. Optionally other UseCases (Frame Generator, Trigger Generator, ) can be upgraded. Features: 2 Ports 1000Base-T MBit/s full duplex on a single unshielded twisted pair. 2 Ports Gigabit Ethernet 1000 BaseTX 6x Digital Trigger Input 6x Digital Trigger Output Automotive Tyco MQS Connectors for 1000Base-T1 and Power Supply Robust steel case DIP Switches for easy configuration Selection of multiple UseCases: o Two independent MediaConverters o 2x SPY for listening on a 1000Base-T1 Channel Power requirement: 8 to 16 Volt DC (nominal 12 Volt DC) Power consumption: 4 to 7 Watt Size: 110 x 108 x 28 mm Weight: 0,4 kg International Protection: IP 2 0 Operating Temperature: -20 to +80 Celsius Page 4 of 24

5 2 Warranty and Safety Information Before operating the device, read this manual thoroughly and retain it for your reference. Use the device only as described in this manual. Use only in dry conditions. Do not apply power to a damaged device. Do not open the device. Otherwise warranty will be lost. This device is designed for engineering purpose only. Special care has to be taken for operation. Do not use this device in a series production car. As this device is likely to be used under rough conditions, warranty is limited to 1 year. Manufacturer liability for damage caused by using the device is excluded. Page 5 of 24

6 3 Pinning The pinning of the ECU connectors is listed on the label on top of the device Page 6 of 24

7 3.1 Power and 1000Base-T1 connector Connector colour: Black Power supply for the device is supplied by Pin 18 (12 Volt) and Pin 20 (Ground). Warning: If you apply a voltage higher than 18 Volt, the device will be damaged! The Tyco Electronics (TE) Micro Lock System (MQS) is used. Connector Pin Function Base-T1 Port_2, Positive Base-T1 Port_2, Negative Base-T1 Port_1, Positive Base-T1 Port_1, Negative 18 VCC 20 GND Page 7 of 24

8 3.2 SubD 9 Trigger Connector Standard SubD 9 Pos. female connector. This connector is used for digital input and output trigger functions. Pin Function 1 Digital Trigger Input/Output 1 2 Digital Trigger Input/Output 2 3 Signal Ground Reference 4 Signal Ground Reference 5 Signal Ground Reference 6 Digital Trigger Input/Output 3 7 Digital Trigger Input/Output 4 8 Digital Trigger Input/Output 5 9 Digital Trigger Input/Output 6 Digital Trigger Output: Digital Trigger Output Voltage is 3.3 Volt Level with a 4.7 KOhms pull-up resistor Active Low. Drive Strength 20 ma Digital Trigger Input: Digital Trigger Input is a Voltage 3.3 Volt Level with a 4.7 KOhm pull-up resistor Active LOW. 3.3 RJ45 Ethernet connectors There are two RJ45 Standard Ethernet connectors on the front side for Gigabit Ethernet. They are set to be Gigabit Ports. Page 8 of 24

9 4 Status LEDs The 1000Base-T1 SPY mini has several status LEDs at the front side of the case. LED Position State FPGA Up Right On Host Low Right Blink Link 1 Up Left On when 1000Base-T1 link is detected on Port 1 Blinking when data is transmitted Link 2 Down Left On when 1000Base-T1 link is detected on Port 2 Blinking when data is transmitted Centre Centre On when link-up is detected Blinking when data is transmitted Page 9 of 24

10 5 Dip switch configurations The BRSPY mini is configured by 8 DIP Switches on the front of the device. DIP Switch 1: ON = 1000Base-T1 Port 1 is set to Master. OFF = 1000Base-T1 Port 1 is set to Slave. DIP Switch 2: ON = 1000Base-T1 Port 2 is set to Master OFF = 1000Base-T1 Port 2 is set to Slave. DIP Switch 3 to 4: Use Case Selection. Binary Coded from 00 to 11. Please refer chapter Use Cases in this User manual for further information. DIP Switch 5 to 8: Frame Generator speed, burst and packet size selection Page 10 of 24

11 6 Use Cases Different Use Cases can be configured with the DIP Switches 3 and 4 for the 1000Base-T1 SPY mini. After changing these switches, a hardware reset is required. 6.1 Dual Media Converter Mode UseCase 00 : Dual Media Converter Mode The simplest Use Case is the double Media Converter, selected by setting the DIP switches 3 and 4 to 00 (both switches down). The 1000Base-T1 SPY mini will function like completely independent Media Converters from 1000Base-T1 to Gigabit Ethernet in full-duplex mode. The two data streams of the two Media Converters are completely independent of each other. Both data streams are full duplex and the RJ45 Ports are input/output. The PC can send data. There are no buffers in this Use Case. The RJ45 Ports work in Gigabit Ethernet (1000 Mbit/s) Mode in this Use Case. Page 11 of 24

12 6.2 Spy Mode Independent UseCase 01 : Spy Mode Independient. In this Use Case, the copied data from the two 1000Base-T1 Ports are logged independently in the in the 2 ethernets ports. The PC is not able to send data. The RJ45 Ports are output only. The communication between the two 1000Base-T1 ports is possible. Page 12 of 24

13 6.3 Spy Mode 2 in 1 UseCase 10 : Spy Mode 2 in 1 In this Use Case the copied data from the two 1000Base-T1 Mbit/s are logged into one 1000Mb/s stream and are sent on one Gigabit link. To do a collision resolution the packets are buffered on the 1000Base-T1 Port. In this mode, the signals received in 1000Base-T1 Port 1 and 1000Base-T1 Port 2 are combined in one stream and sent on Ethernet Port. The PC is not able to send data. The RJ45 Ports are output only. The communication between the two 1000Base-T1 ports is possible. This UseCase is very powerful in combination with the TimeStamp Feature (see Chapter ): Page 13 of 24

14 6.4 Spy Mode Independent with Wrapper UseCase 11 : Spy Mode Independient with Wrapper (TimeStamp Feature) In this case, a header is added on the Ethernet sent frame. The packet received in the 1000Base-T1 port will be logged through the corresponding Ethernet Port into an Ethernet RAW frame. The following picture shows the structure of an Ethernet 1000Base-T1 SPY mini RAW frame, in this use case: Destination Source Ethernet Time Port Extra Length Payload CRC MAC MAC Type Stamp (1 (1 (2 (BR (4 (6 bytes) (6 (2 bytes) (6 byte) byte) bytes) packet) bytes) bytes) bytes) Ethernet 1000Base- T1 mini Frame Header Field Name No. Of Value Bytes Destination MAC Address 6 FF:FF:FF:FF:FF:FF Source MAC Address 6 00:50:C2:E4:30:00 Ethernet Type 2 0x2182 Time Stamp 6 See the note below Port 1 See the table below Extra 1 0x00 Length 2 Length of the Ethernet Gigabit SPY mini frame Payload X BroadR-Reach packet CRC 4 Note: The data Frames are enhanced with additional information as an exact timestamp and the bus port the data was originally sent on. Timestamps are in 0.04 μs resolution and synchronous to all connected lines. With this feature the user can record the exact time when the first bytes of a frame were received on a 1000Base-T1 port of the 1000Base-T1 SPY mini. It is also possible to see the complete frame including the preamble and the CRC in Wireshark. Normally this information is re-moved by your network interface Note: The following table shows the values of Port field: Port 1000Base-T Base-T1 2 Value 0x00 0x01 Page 14 of 24

15 The following image shows an example of a 1000Base-T1 payload frame encapsulated in a 1000Base-T1 RAW frame, with header: Page 15 of 24

16 Base-T1 SPY mini LUA Dissector Installation Guide In order to dissect the 1000Base-T1 SPY mini RAW Ethernet Frames, a LUA file for Wireshark is avail-able on Technica Engineering website. To install the LUA file in Wireshark, the user must follow the following steps: 1. Close Wireshark in case that the program is running on PC. 2. Download the.zip file that contains all the LUA files, through this website: SPY-Mini-Wireshark-Dissector.zip 3. Extract the downloaded ZIP file. This file should contain the following LUA file: Gigabit_SPY_Mini_ETH_wrapper_BR.lua 4. Copy or move the LUA file in Wireshark plugins folder. The path should be: C:\Program Files\Wireshark\plugins\(Wireshark Version Number). Note: Wireshark Version Number depends on the Wireshark version installed on Page 16 of 24

17 5. In order to copy or move the LUA files to the specified Wireshark plugins folder, Administrator rights will be needed. In that case, the following window should appear. Press Continue to proceed with the copy. 6. Run Wireshark. Page 17 of 24

18 6.6 Frame Generator Mode In this case, the device works as a Frame Generator, sending Ethernet frames on GB1 with Gigabit Speed and on all Base-T1 ports with 1000Mbit/s. In order to select this mode, the DIP switches 3 and 4 must be ON ( 11 Value). In addition, the user can select different functionalities according with the set of DIP switches 5,6,7 and 8: DIP Switch 5: When it is ON, it selects the Burst Mode. In this mode, the device sends 4 packets with the minimum IFG (Interframe Gap). These sequences of packets consists on a burst of mixed packets -a large frame and three small frames. DIP Switch 6: This switch selects the Packets Size. When it is OFF, the size of the frame will be 64 bytes, and when it is ON, the size will be 1500 bytes. The sizes don t include the preamble and CRC. DIP Switches 7 and 8: This switch allows to select the Framerate: o DIP Switch 7 OFF, DIP Switch 8 OFF ( 00 ): 5 MBit/s o DIP Switch 7 OFF, DIP Switch 8 ON ( 01 ): 50 MBit/s o DIP Switch 7 ON, DIP Switch 8 OFF ( 10 ): 90 MBit/s o DIP Switch 7 ON, DIP Switch 8 ON ( 11 ): 98 MBit/s These rates are used in all 1000Base-T1 ports, and in GB2. In Frame Generator mode, this port will work as Fast Ethernet port, sending status frames -see section In GB1, these values are multiplied by Frame Format The following image shows the Frame Format transmitted on all 1000Base-T1 ports and GB port in Frame Generator Mode. The frame format is fixed, and the only difference between the packets is the Stream ID field. This field shows the port number where the frame is being sent, as it follows: Page 18 of 24

19 Stream ID Value Function The following image shows an example with mixed frame sizes in Wireshark, in burst mode: Page 19 of 24

20 6.7 Status Reporter On any of the 1000Base-T1 and in GB1, the CRC and Continuous Counter fields are checked and the result is reported each second in a Status Frame. This frame is transmitted on GB2 with the following format: In this port, the StreamID = 5, and the GB1 works as a Fast Ethernet port. The following image shows an example of a Status Frame in Wireshark: The following table defines the content of the Status Frame Data. These fields are replicated two times, one per 1000Base-T1 port, giving information about the communication status in every single port. Page 20 of 24

21 Field Size Description (bytes) SequenceCounterLocked 2 Lowest Bit shows if the Sequence Counter Checker found at least one valid pair and then was enabled. It is disabled while errors occur. SequenceErrorCounter 2 Counter for detected sequence errors after checker locked. This counter is not reset. IgnoredFrameCounter 2 Counter for frames, that were not in the right format to be checked. CRC_ErrorCounter 2 Counter for CRC errors in all received frames ReceivedFrameCounter 2 Total of all received frames including malformed frames MeasuredFramesPerSecond 2 Received Frames per second with valid preamble. MeasuredBitsPerSecond 2 RX_DV High Time vs. Low Time [MBits/s] Page 21 of 24

22 7 Trigger Functions The Trigger Output signals detect when a frame is received in one of the 1000Base-T1 ports -when detects the Data Valid rising edge-, and when a frame is being transmitted on one of the Ethernet ports, as is shown in the following table: Pin Function Base-T1 Data Valid Base-T1 Data Valid 3 Signal Ground Reference 4 Signal Ground Reference 5 Signal Ground Reference 6 GB1 Data Enable 7 GB2 Data Enable Page 22 of 24

23 8 Frequently Asked Questions FAQ Q: What is the delay time for Ethernet packets through the SPY? A: The delay time depends on the UseCase that is set. For SPY Mode without wrapper the delay is around 12µs. For Media Converter Mode, the delay is around 2.8µs. This delay is independent of the Ethernet packet frame size. Q: What is the delay time for Ethernet packets between two 1000Base-T1 ports? A: For the Media Converter Mode, the delay between 1000Base-T1 ports is around 1.5µs. The delay is independent of the Ethernet packet frame size. Q: Is AVB supported? A: The SPY is especially built for testing AVB. For minimum delay the SPY has to be set to SPY Use Case. When using automotive AVB profile the time synchronization is not influenced by the SPY. There is no special handling of AVB frames as this is not necessary. Q: The 1000Base-T1 Link LED is lit but I have no valid Link. What is going wrong? A: There is a bug in the used 1000Base-T1 PHY. When the 1000Base-T1 Plus and Minus lines are swapped, and the SPY Port is set to 1000Base-T1 Slave then the Link LED is lit, but there is no data trans-mission possible. So please connect the 1000Base-T1 lines preoperly. Q: I am not able to see any packet in Wireshark in SPY -with or without wrapper- mode. What is going wrong? A: Some Ethernet Adapters must have the VLAN & Packet Priority option disabled. Please, change this configuration, going to Ethernet Adapter Properties/Advanced/Packet Priori-ty & VLAN. If this option is enabled, just disabled. Otherwise, it should be enabled. Page 23 of 24

24 9 Contact If you have any questions regarding this product, please feel free to contact us: Technica Engineering GmbH Leopoldstr München Germany Page 24 of 24