HDLC-ETH. Serial Ethernet Converter. Rev. Dec 20, Datasheet. Website:

Transcription

1 HDLC-ETH Serial Ethernet Converter Rev. Dec 20, 2017 HDLC-ETH Datasheet Website:

2 1 Overview Introduction Features Applications Technical Specifications Order Information Hardware Interface Appearance LED Indicators Ethernet Interface Serial Port DC: power interface Building Configuration Environment yacer-dms Configuration Management Software Get the Configuration Management Software yacer-dms Official website of yacer Accompanied USB disk Run yacer-dms Unzip the file Run yacer-dms Main Window of DMS Statistical Report Receive/transmit indication Information display Control Widget Configure Device Function and Configuration Ethernet Interface Configuration Device alias IP address configuration Default gateway Announce Configuration Serial Port Configuration Select the working mode of the serial port HDLC-NRZ parameter configuration Bit Stream parameters UART parameter configuration UART-HDLC parameter configuration UDP to Serial Conversion Application model Protocol Conversion Parameter configuration Page 1 yacer@yacer.cn

3 5.3.4 Receive multicast Serial to UDP Conversion Application model Protocol Conversion Parameter configuration How does the UDP server identify the source serial Serial to Serial Conversion Firmware Version Upgrade Start Upgrade Locate Firmware Version Upgrade Completed Upgrade Confirmation Device Reboot PING Page 2 yacer@yacer.cn

4 1 Overview 1.1 Introduction The Yacer HDLC-ETH protocol converter, provides dual or quad RS-232 synchronous & asynchronous serial ports, dual 10/100M Ethernet interface to achieve the protocol conversion between the serial port and the Ethernet interface. Small footprint, +12V power supply, industrial wide temperature. 1.2 Features Dual 10/100M Ethernet interface, with support for the Ethernet switching, VLAN and dual-ip functions Dual or quad RS-232 synchronous & asynchronous serial ports Full-duplex, with the baud rate up to 250 Kbps Support for the synchronous HDLC protocol, asynchronous UART 15KV ESD protection +12V power supply Industrial wide temperature 1.3 Applications Secondary Surveillance Radar (SSR), ADS-B data communication Air Traffic Management (ATM) Air Traffic Control (ATC) Synchronous & Asynchronous serial communication and conversion Embedded application Page 3 yacer@yacer.cn

5 1.4 Technical Specifications Serial Port Quantity 2, 4 x RJ-45 Working mode Synchronous HDLC, Asynchronous UART Interface type RS-232 full-duplex Encoding format NRZ Baud rate 250 Kbps HDLC frame length 1470 bytes Synchronous clock Normal, slave and master clock mode ESD protection ± 15 KV Ethernet Interface Quantity 2 x RJ-45 Function Ethernet switching support VLAN and dual-ip support Rate 10/100 Mbps, auto MDI/MDI-X Network protocol TCP/IP UDP Server, UDP Client Programming interface Unicast/Multicast/Broadcast Configuration Management Software tool yacer-dms configuration management software Management interface Ethernet interface Power Requirements Input voltage +12V Power consumption < 3W Power interface DC mm interface Mechanical Characteristics Dimensions HxWxD: 32 mm x mm x 124 mm Weight 450g Enclosure Aluminum alloy fully-enclosed enclosure, IP30 Operating Environment Operating temperature -40 ~ +85 Storage temperature -40 ~ +85 Operating humidity 5~95% (non condensing) 1.5 Order Information Model RS-232 Serial Port Ethernet Interface HDLC-ETH x synchronous/asynchronous serial ports 2 x 10/100M HDLC-ETH x synchronous/asynchronous serial ports + 2 x synchronous serial ports 2 x 10/100M Page 4 yacer@yacer.cn

6 2 Hardware Interface 2.1 Appearance Quad serial interfaces (S1~S4) and dual Ethernet interfaces (ETH1, ETH2) are located on the front side of the product while the DC power interface is located on the back side. The serial port and Ethernet interface both adopt the RJ-45 connector. 2.2 LED Indicators LED ALARM RUN POWER Description Alarm indicator, on when the device is not ready to start or in case of failure, and constantly off during normal operation Running indicator, flashing during normal operation Power indicator, constantly on after powered 2.3 Ethernet Interface The dual 10/100M Ethernet RJ-45 interface supports for auto MDI/MDIX. Ethernet switching, VLAN and dual-ip support. RJ45 Pin Ethernet Signal 1 Tx+ 2 Tx- 3 Rx+ 6 Rx- Page 5 yacer@yacer.cn

7 2.4 Serial Port With the RJ-45 connector, it provides dual or quad RS-232 synchronous/asynchronous serial ports with support for the HDLC protocol. Each RJ45 is provided with two indicators; the yellow light flashing indicates data transmission while the green light flashing indicates data receiving. RJ45 Pin RS-232 Description 1 GND Ground 2 TxData Transmit Data 3 4 TxClock Transmit Clock 5 6 RxData Receive Data 7 8 RxClock Receive Clock 2.5 DC: power interface HDLC-ETH operates with the +12V DC power supply. 3 Building Configuration Environment below. Connect the management computer and HDLC-ETH over the network cable, as shown Ethernet Page 6 yacer@yacer.cn

8 4 yacer-dms Configuration Management Software 4.1 Get the Configuration Management Software yacer-dms Official website of yacer Visit the official website of yacer to enter the Tools channel, and open the yacer-dms software page to download the latest version of the software Accompanied USB disk folder. Insert the accompanied USB disk to the PC, open it and double-click to enter the Tools Page 7 yacer@yacer.cn

9 4.2 Run yacer-dms Unzip the file After getting the yacer-dms.zip compressed file, first unzip it. With the Extract Compressed Folder dialog box popping up, set the path for saving extracted files in the box and click on the Extract button once set up. Page 8 yacer@yacer.cn

10 4.2.2 Run yacer-dms Locate the decompressed folder according to the path for extracting the compressed files and click on it. Locate the yacer-dms.exe file under directory and double-click on this file to run the configuration software. Page 9 yacer@yacer.cn

11 4.3 Main Window of DMS Below is the main window of the configuration management software yacer-dms, including three parts: Toolbar: Function operation buttons Device List: Displaying the basic information and running status of the on-line device Statistical Report: Displaying the receive/transmit indication & statistics, and device details of the specified device 4.4 Statistical Report Receive/transmit indication Transmit: Each time the corresponding serial port transmits one frame data, the transmit indicator flashes once. Receive: Each time the corresponding serial port receives one frame data, the receive indicator flashes once. Page 10

12 4.4.2 Information display The information display area is located on the right side of the statistical report, showing the following contents: Device Information: Running time, serial number, IP address, version number Serial Port: Receive/transmit statistics of all serial ports UDP Transmit: Displaying the relevant transmitted packets of the UDP Client for each enabled serial port to UDP entry UDP Receive: Displaying the relevant received packets of the UDP Server for each enabled UDP to serial port entry DMS Service: Displaying the information receive/transmit statistics of the configuration management between the device and the configured management computer Control Widget The statistical report includes the following control widgets: Control Widget Function Set the refresh period of report Manually refresh the statistical report Clear the statistical report Page 11

13 4.5 Configure Device Click on the button on the toolbar or double-click on the specified device in the device list; yacer-dms pops up the configuration dialog. According to the interface and function, the dialog divides the configuration item into several configuration pages. The following operation buttons are located at the bottom of the dialog: Button Function Save the configuration content of the current dialog to the file Open the configuration file and read the refreshed configuration dialog content Refresh the dialog content with the device s default factory configuration Write the configuration content of the dialog into the device and restart the device to bring the configuration into effect Cancel the current configuration operation Page 12 yacer@yacer.cn

14 5 Function and Configuration 5.1 Ethernet Interface Configuration Device alias It allows users to set an alias for the HDLC-ETH, thus adding description to the device or helping to remember the identification IP address configuration Ethernet switching enable By default, check the checkbox to enable the built-in Ethernet switch, providing the Ethernet switching function between ETH1 and ETH2. While the Ethernet switching function has been enabled, HDLC-ETH only has one IP address. The network function figure as follows: HDLC-ETH CPU Ethernet Port Ethernet Port Built-in Ethernet ETH1 Switch ETH2 Page 13

15 Dual IP configuration When the checkbox is unchecked, ensure ETH1 and ETH2 are not on the same subnet for configuration as they have an independent IP address. With the dual-ip function figure as follows, the HDLC-ETH is equivalent to a PC equipped with two network cards. HDLC-ETH CPU ETH ETH Page 14 yacer@yacer.cn

16 5.1.3 Default gateway By default, the default gateway is , representing that there is no gateway configuration. If HDLC-ETH needs to communicate with the host on other subnet, it must rely on an external router. At this time, the HDLC-ETH s IP address must be on the same subnet with the IP address of the connected router port. Meanwhile, the IP address of router is set to the default gateway. As shown below, the IP address of HDLC-ETH and remote PC is and respectively. As they do not belong to the same subnet, they must rely on the router for communication. HDLC-ETH and PC need to set the IP address of the connected router port to the default gateway of this device IP address: Default gateway: IP address: Default gateway: Page 15 yacer@yacer.cn

17 5.1.4 Announce Configuration HDLC-ETH can announce the notification data and provides the host computer with the serial card operation information and receive/transmit statistics of the data communication. The announce setting includes the following parameters: Parameters Description Multicast address The notification is sent via multicast with the multicast address of that can't be changed Destination port Notification is sent via the UDP message with the destination port number of 8527 that can't be changed Announce period of the Transmit period of device running the information device information notification, 1~255 seconds Announce period of the Transmit period of receive/transmit statistics, 1~255 statistical report seconds Page 16

18 5.2 Serial Port Configuration Select the working mode of the serial port Serial S1 and S2 are synchronous and asynchronous serial ports, with support for the synchronous and asynchronous working modes. Other serial ports are synchronous, with support only for the synchronous working mode. Working Mode Description Ports Supported UART universal asynchronous serial, equivalent to S1, S2 Asynchronous the serial port on the common computer UART- HDLC UART-based similar HDLC communication S1, S2 protocol HDLC-NRZ Synchronous HDLC protocol based on the S1, S2, S3, S4 Synchronous NRZ encoding Bit Stream Serial Bit data based on the receive clock S1, S2, S3, S4 sampling Users can select the desired working mode from the working mode combobox. Due to different parameter configuration of each working mode, contents of the Others cell will be adjusted automatically according to the determined working mode. If further configuration of working parameters of the selected working mode is required, mouse double-click on the Others cell to pop up the parameter configuration dialog. Page 17

19 5.2.2 HDLC-NRZ parameter configuration HDLC-NRZ is the common synchronous working mode, which is mainly used for the secondary surveillance radar and ADS-B data communication in the air traffic control (ATC) and air traffic management (ATM) fields Clock mode There are three clock modes for the synchronous serial port, normal, slave clock and master clock. Clock Mode Transmit Clock Receive Clock Normal Generation from the local device, Generation from the opposite TxC output device, RxC input Slave Clock Generation from the opposite Generation of the opposite device, (External) device, RxC input RxC input TxC output synchronizes with RxC automatically Master Clock Generation of the local device, TxC output Generation of the local device, ignoring the RxC clock The slave clock mode is also called as the external clock working mode. When the opposite device is the DCE, HDLC-ETH is often configured as the slave clock mode and transmits data with the clock provided by the DCE, ensuring the data transmission across the whole network based a clock and avoiding packet loss concerns caused due to different clock sources. Page 18 yacer@yacer.cn

20 Transmit trigger Transmit trigger defines the generation clock edge of the new data bit: Falling edge of clock: A new data bit is generated on the falling edge of clock Rising edge of clock: A new data bit is generated on the rising edge of clock During the ATC communication, falling edge of clock is generally chosen to trigger the new data transmission. In some custom development applications, sometimes users will adopt the rising edge to trigger the new data transmission Receive trigger Receive trigger defines the sampling clock edge of the serial port receive data: Rising edge of clock: Data on the RxD line is read on the rising edge of the RxC signal Falling edge of clock: Data on the RxD line is read on the falling edge of the RxC signal During the ATC communication, receive trigger must be configured as the rising edge of clock to ensure correct reading of data as it takes time to stabilize the new data that is triggered with the falling edge. The local receive trigger configuration is determined according to the transmit trigger of the remote terminal device: Remote Transmit Trigger Falling edge of clock Rising edge of clock Local Receive Trigger Rising edge of clock Falling edge of clock Protocol ISO HDLC: ISO HDLC protocol standard IBM SDLC: SDLC protocol standard Page 19 yacer@yacer.cn

21 Leading Sign and Number In some specific applications, especially the half-duplex applications, a leading sign is required in front of the frame. For example, 2~5 0x7E leadings are added for synchronization of the receiver. For the full-duplex applications, leading is always not required with the number of leadings set to be zero (no leading) CRC enable By default, the HDLC protocol communication should enable the CRC function. CRC Enable Data Transmit Data Receive HDLC-ETH automatically calculates the CRC data, and adds a 2-byte FCS field at the end of data Check CRC of the receive frame and discard the data frame with the check failed No CRC calculation or FCS field adding No CRC check and receive all frames Forward received FCS field This configuration is only effective with CRC enable.the HDLC frame structure is shown in the following table, where FCS is the frame check sequence field. By default, this option is not checked; HDLC-ETH will discard the 2-byte FCS field at the end of data and only forward the user data after the receive HDLC frame check is passed. If this option is checked, then forward the user data and FCS field. Opening Flag Address Field Control Field Information Field FCS Field Closing Flag 0x7E 1 byte 1 byte Variable length CRC 2 bytes 0x7E 0x7E User data CRC 2 bytes 0x7E Page 20 yacer@yacer.cn

22 5.2.3 Bit Stream parameters The rising or falling edge of each clock cycle samples the 1bit data on the data line, which forms a UDP message and sends to the destination IP after receiving a byte with the packet length by forming a byte with each 8bit. Refer to the HDLC-NRZ parameter configuration for configuration of clock mode, transmit trigger, receive trigger and idle flag. The online bit stream is stored in the computer or system memory in the form of byte.the receive/transmit sequence determines the conversion mode of byte and bit. Receive/Transmit Sequence Transmit Operation Receive Operation MSB first First transmit the high-bit byte Data received first is placed on the byte high bit LSB first First transmit the low-bit byte Data received first is placed on the byte low bit Page 21 yacer@yacer.cn

23 5.2.4 UART parameter configuration Asynchronous UART is a character stream communication; data bits, parity bits and stop bits define the basic working parameters of the asynchronous serial port, which must be configured identically to the opposite terminal device. Generally, data bits are defined as 8, i.e. one byte, and UART corresponds to the byte stream communication. When the UART byte stream is converted into a UDP message or HDLC frame, it is too costly and inefficient if each byte is converted to a UDP message for transmission. To improve efficiency, the protocol converter buffers the received byte stream and forms a number of buffered bytes into a UDP message to send, of which this process is called as packet. Packets are controlled with two parameters, namely the packet length and the packet interval Packet length For example, if the packet length is set to 128 bytes, then it will form a UDP message to send after UART receives the full 128 bytes Packet interval Packet improves the UDP transmission efficiency, but also introduces new problems. As shown in the above example again, if the transmitter sends 100 bytes and stops sending, the receiver will always be waiting as the packet length is less than 128 bytes. In order to solve the problem of waiting, users need to configure the packet interval parameter, such as set to 10ms; then data received by UART will wait for a maximum of 10ms.In case of 10ms timeout, it will convert the buffer data into a UDP message to send no matter whether it has received the full 128 bytes. Page 22 yacer@yacer.cn

24 5.2.5 UART-HDLC parameter configuration The UART-HDLC working mode is a custom protocol by yacer which form the asynchronous HDLC frame on the basis of the normal UART communication by packaging the byte stream. Therefore, the asynchronous serial port can perform the packet-based communication with the UDP message and synchronous HDLC frame. The UART-HDLC frame format adds 0x7E before and after the packet as the opening flag and closing flag with the frame structure as follows: opening Flag Information Field FCS Field closing Flag 0x7E bytes of data 2-byte CRC data 0x7E As the information field and FCS field may appear 0x7E, perform the character escape on such fields before transmission with the escape rules as follows: 0x7E: Escaped to two characters, 0x7D 0x5E 0x7D: Escaped to two characters, 0x7D 0x5D Other characters: No escape The escape operation of data transmit is as follows: Original Data Actual Transmit Data 0x7E 0x7D 0x5E 0x7D 0x7D 0x5D Others No change The escape operation of data receive is as follows: Actual Receive Data Data 0x7D 0x5E 0x7E 0x7D 0x5D 0x7D Others No change Page 23 yacer@yacer.cn

25 5.3 UDP to Serial Conversion Application model With HDLC-ETH, PC or server can realize the transmit function of the synchronous HDLC serial port. The typical application is shown as follows. PC sends a UDP message over the Ethernet interface as the UDP Client, and HDLC-ETH sends it out from the synchronous serial port after converting the received UDP message into the HDLC frame. yacer HDLC-ETH Synchronous Serial Port HDLC PC Ethernet UDP Ethernet UDP Interface Interface Client UDP Server Synchronous Serial Port Protocol Conversion The most typical UDP-to-HDLC application is shown below. HDLC-ETH loads the UDP application data into the user data area of the HDLC frame, and then calculates CRC and populates the FCS field to form a complete HDLC frame to send. In order to reduce the calculation load of PC and the user programming complexity, normally, the FCS field of HDLC is not included in the UDP message, which is populated through HDLC-ETH calculation. IP Header UDP Header Application Data UDP to HDLC Opening Flag User data FCS Field Closing Flag 0x7E Variable length CRC 2 bytes 0x7E Page 24 yacer@yacer.cn

26 5.3.3 Parameter configuration Set the UDP to serial port. Each row represents the forwarding entry from a UDP port to the serial port with three forwarding strategies to be achieved: Forwarding: Data received by the specified UDP port can be forwarded to the specified serial port. Multiplexer: Data received by several different UDP ports can be forwarded to the same serial port. Demultiplexer: Data received from the same UDP port can be forwarded to the different serial ports. The following configuration realizes the application, where data received from a UDP and distributed to 4 serial ports: Receive multicast If users need to receive the multicast UDP message, add the required multicast address from the right Rx Multicast Address list. Range of the multicast address is ~ , is the configuration management address of the HDLC-ETH and users can t use this address. The multicast address configured as indicates that the entry is not in effect. Page 25 yacer@yacer.cn

27 5.4 Serial to UDP Conversion Application model The HDLC-to-UDP function figure is shown below. HDLC-ETH receives the HDLC frame from other devices over the synchronous serial interface, converts it into the UDP message and sends to PC or server over Ethernet. HDLC Synchronous Serial Port HDLC- ETH Ethernet UDP Ethernet PC UDP Interface Interface Synchronous Serial Port Client UDP Server Protocol Conversion To ensure the integrity of user data, HDLC-ETH places the complete HDLC frame in the UDP application data, and forwards to the UDP Server. Opening Flag Address Field Control Field Information Field FCS Field Closing Flag 0x7E 1 byte 1 byte Variable length, CRC 2 bytes 0x7E N-byte HDLC-to-UDP IP Header UDP Header Application Data Page 26 yacer@yacer.cn

28 5.4.3 Parameter configuration Set the serial port to UDP. Each row represents the forwarding entry from a serial port to the UDP port with three forwarding strategies to be achieved: Forwarding: Data received from the specified serial port can be forwarded to the specified destination UDP port. Multiplexer: Data received from several different serial ports can be forwarded to the same destination UDP port. Demultiplexer: Data received from the same serial port can be forwarded to the different destination UDP ports. As shown above, three serial port to UDP entries are configured for achieving the following items: Serial port S1 to UDP unicast, with the destination IP address as and destination UDP port as 8000 Serial port S2 to UDP broadcast, all hosts on the subnet can receive data from S2 at the 9000 port Serial port S3 to UDP multicast, only the PC joining Group on the network can receive data from S How does the UDP server identify the source serial In many applications, such as the ATC, the HDLC frame from several different serial ports needs to be forwarded to a server or PC. In this case, a strategy enables PC to know which serial port the received UDP message data is from. Page 27 yacer@yacer.cn

29 Distinguish the source serial port according to the destination UDP port As shown below, set different forwarding destination UDP ports for each serial port. The UDP Server PC receives data at the different UDP ports. Message received at port 8001 is from the serial port S1 while message received at port 8002 is from the serial port S Distinguish the source serial port according to the source UDP port When the source serial port is identified with the destination UDP port, UDP Server needs to listen and receive data on a plurality of UDP ports. In case there are many serial ports, not only the UDP Server port occupies too many resources, the configuration and programming complexity also increases significantly. In order to simplify implementation of the UDP Server side, we can use the configuration example below, forwarding each conversion to the same port of the UDP Server. During yacer s HDLC-ETH forwarding, it will automatically adjust the source port number of the UDP message according to the source serial port. The source ports of the UDP message forwarded by the serial ports S1 and S2 are 8001 and 8002 respectively; the following is gradually increasing. Thus, UDP Server only needs to listen and receive data at a port (8000 in the example below) and distinguishes the source serial port according to the source UDP port. If several HDLC-ETHs are provided, UDP Server can distinguish the source device via the source IP. Page 28 yacer@yacer.cn

30 5.5 Serial to Serial Conversion Serial-serial can forward the input data of the specified serial port to other serial port outputs, which is mainly used for: Conversion between synchronous and asynchronous serial ports Serial port Demultiplexer: Divide the single serial port data into multi-channel data. Unlike the common demultiplexer, demultiplexing is possible with HDLC-ETH, the different baud rates and clock modes can be set for each-channel serial port, avoiding the packet loss caused by clock inconsistency. Configuration shown above realizes the application of the input demultiplexing of the serial port S1 to S2, S3 and S4 outputs. HDLC-ETH performs storing and forwarding on the received data. Even if the baud rate and clock mode of S1, S2, S3 and S4 are different, packet will not loss. HDLC-ETH Serial Port-S2 Serial Port-S1 Store & Forward Serial Port-S3 Serial Port-S4 Page 29

31 6 Firmware Version Upgrade 6.1 Start Upgrade Click on the click on the button on the toolbar to pop up the version upgrade dialog, and then button. 6.2 Locate Firmware Version The Selection Version File dialog pops up. Locate the folder for storing the latest firmware version, select and click Open to start updating. Page 30

32 6.3 Upgrade Completed After completion of upgrade, Version Update Completed displaying on the page indicates that the version update is completed. 6.4 Upgrade Confirmation After completion of update, re power-on the device, observe the version information in the statistical report and determine whether the new version is updated successfully via the version date. Page 31

33 7 Device Reboot Click on the click on the button on the toolbar to pop up the device reboot dialog, and then button to reboot the device. 8 PING By clicking on the button on the toolbar, DMS will start the ping command automatically for the selected device so as to check whether the network connection between the configuration management computer and HDLC-ETH is normal. Before performing the Ping command, first ensure that the IP address of PC and HDLC-ETH is on the same subnet. Page 32 yacer@yacer.cn