FEATURES HARDWARE CONNECTION

Transcription

1 1

2 FEATURES 1. Support ANSI T1.413 ISSUE 2, ITU G (G.DMT), ITU G (G.LITE), ITU G992.3, ITU G Web-based configuration and monitoring. 3. Support multiple PVCs. 4. Routing function. 5. NAPT, DHCP function. HARDWARE CONNECTION 2

3 INTRODUCTION 1. Use a telephone cord to connect the LINE port of the splitter with the RJ-11 port (the phone jack) on the wall. 2. Use another telephone cord to connect the ADSL port of the splitter with the LINE port of the ADSL Modem. 3. Use another telephone cord to connect the telephone set with the PHONE port of the splitter. 4. Connect Ethernet port of the ADSL MODEM with 10/100BASE-T port of the computer using the network cable that comes with the modem. 5. Plug in the power cord, and turn on the power. If you do not want Internet services and telephone voice services simultaneously, please just connect the LINE port of the ADSL Modem with the RJ-11 port (the phone jack) on the wall using a telephone cord. In this case, the splitter is not necessary. 3

4 LED STATUS INDICATION Status Steady light Flashing / Fast flashing Off POWER (Red) Power on / / Power off DSL (Yellow) The modem is in good connection In handshaking status Connection not set up INTERNET (Green) Connected with PC / / Transmitting or receiving data Not connected with PC properly WIRELESS (Green) Wireless is connected Transforming data Wireless is disabled DEFAULT CONFIGURATION ADSL MODEM has pre-configured with the VCI/VPI which is in common use. The default dial-up mode is bridge encapsulation. For bridge mode, no need to configure any more parameter. However, the third party dial-up software is needed for connection with the Internet. COMPUTER CONFIGURATION The default IP address for ADSL MODEM is: ; The Subnet Mask is: Users can configure ADSL MODEM through an Internet browser. ADSL MODEM can be used as gateway and DNS server; users need to set the computer s TCP/IP protocol as follow: 4

5 1. Set the computer IP address at same segment of ADSL MODEM,such as set the IP address of the network card to one of the ~ Set the computer s gateway the same IP address as the ADSL Modem s. 3. Set computer s DNS server the same as ADSL Modem s IP address or that of an effective DNS server. ADSL MODEM CONFIGURATION LOG IN Open the browser; input at the address column. Press Enter key then the entry dialog box will show up as Figure. Input Username: admin, Password: password (capital sensitive), then press Enter. 5

6 SAVE SETTING After getting through each page for parameters setting, click Save or Save apply to store the value in ADSL MODEM. Briefly, we named Save. Note: When you save the settings, the web page will be refreshed slowly, please wait it finished. After you save the settings, it will take effect until next reboot. Some settings only take effect after rebooting the router. WIRELESS CONFIGURATION Press Wireless on the top of web pages to enter wireless section. You can select to configure wireless setup, security and management. WIRELESS SETUP Click Setup on the left menu to setup basic wireless parameters. In default, check Enable Wireless box to launch wireless AP. SSID (Service Set Identifier): The mobile users cannot access WLAN until setting their SSID as the same value of the wireless ADSL. The SSID value of the ADSL is default Hidden Access Point: If checked, wireless station will no see SSID of the ADSL. 6

7 WIRELESS SECURITY Press Security on the left menu to construct wireless security. You can select to configure WEP encryption, Shared, 802.1x, WPA, and WPA2 authentication. WEP Encryption Select Enabled of the WEP encryption list. You can enter WEP encryption page. Encryption Strength: Key length: 128bits or 64bits. Network Key 1-4: Up to four keys that are in form of hex digitals could be set. Mobile users can t access the AP if they haven t set the same key as AP. For 64bits and 128bits keys, you should input 10 and 26 hexadecimal digitals or 5 and 13 ASCII characters respectively. Every two digitals should be comparted with others by a space character. For example: 7890ABCDEF (hexadecimal digitals) or QWERT (ASCII characters) for a key length of 64bits x Authentication Select 802.1x to enter 802.1x authentication page. The 802.1x authentication needs a Radius server in LAN. In this page, you can input Radius server IP address, port number and secret key. WIRELESS MAC FILTER In fact, the Access List function is just like MAC address filtering and selected to permit or forbid access of wireless station with specified MAC address. Method: select Allow or Deny mode, and click Add button, and input MAC address which you want to allow or deny. 7

8 PASSWORD CONFIGURATION When you configure ADSL MODEM through an Internet browser, the system requires user name and password to validate access permission. The factory sets the modem at a default username of admin and the password of password. The username is unchanged. You can enter the password configuration on Configuration column to change the password. Attention: please remember the password after change, otherwise you will not be able to change configuration after saving setting Datasheen Corporation Taiwan 8