REQUEST FOR PROPOSAL FOR PROCUREMENT AND INSTALLATION SWITCHES AND TRANSCEIVERS MODULES BILL OF MATERIALS

Transcription

1 REQUEST FOR PROPOSAL FOR PROCUREMENT AND INSTALLATION SWITCHES AND TRANSCEIVERS MODULES Active Components: BILL OF MATERIALS 1. Switch 24 Ethernet 10/100 PoE ports (370W capacity) dual-purpose ports (10/100/1000 or SFP) 2. Transceivers Modules(GLC-SX-MM) Support pack of the all active components for 3 years --01 Passive Components (Systimax): 1. CAT 6A 24-Port Patch Panel(Unloaded) Category 6A Information Outlet Single Port Face Plate with Back Box Cat 6A 7ft Patch cord Cat 6A 3 ft Patch cord --04 Service: 1. Laying Cat 6A utp cable --80 Mtrs 2. I/O Termination --08 Sl No. General Features Switch 24 Ethernet 10/100 PoE ports (370W capacity) Specifications 1 The switch should have minimum 24 x 10/ af PoE Ports & 2 x Combo Uplink ports i.e. 2x SFP and 2 x1000baset ports (any 2 ports usable at a time) 2 Should provide 15.4 W power to all 24 PoE ports Performance 1 16 Gbps Switching fabric 2 Forwarding rate Mpps 3 Configurable up to 8000 MAC addresses 4 Should support jumbo frames of 9016 bytes

2 Layer-2 Features 1 IEEE 802.1Q VLAN encapsulation. Upto 64 VLANs should be supported. Support for 4000 VLAN IDs. 2 Centralized VLAN Management. VLANs created on the Core Switches should be propagated automatically d, 802.1s, 802.1w, 802.3ad 4 IGMP snooping v3, Support for upto 256 IGMP Groups. IGMP filtering. 5 Port Aggregation Protocol (PAgP), Link Aggregation Protocol (LACP) 6 Support for Detection of Unidirectional Links and to disable them to avoid problems such as spanning-tree loops. 7 Per-port broadcast, multicast, and storm control to prevent faulty end stations from degrading overall systems performance. 8 Local Proxy Address Resolution Protocol (ARP) to work in conjunction with Private VLAN Edge to minimize broadcasts and maximize available bandwidth. Network security features 1 IEEE 802.1x to allow dynamic, port-based security, providing user authentication. 2 Port-based ACLs for Layer 2 interfaces to allow application of security policies on individual switch ports. 3 SSHv2 and SNMPv3 to provide network security by encrypting administrator traffic during Telnet and SNMP sessions. 4 TACACS+ and RADIUS authentication enable centralized control of the switch and restrict unauthorized users from altering the configuration. 5 MAC address notification to allow administrators to be notified of users added to or removed from the network. Quality of Service (QoS) & Control 1 Standard 802.1p CoS and DSCP 2 Four egress queues per port to enable differentiated management of up to four traffic types 3 Weighted tail drop (WTD) to provide congestion avoidance 4 There should not be any performance penalty for highly granular QoS functions. Management(Superior manageability Features) 1 Command Line Interface (CLI) support for configuration & troubleshooting purposes. 2 For enhanced traffic management, monitoring, and analysis, upto four RMON groups (history, statistics, alarms, and events) must be supported. 3 Layer 2 trace route to ease troubleshooting by identifying the physical path that a packet takes from source to destination.

3 4 Trivial File Transfer Protocol (TFTP) to reduce the cost of administering software upgrades by downloading from a centralized location. 5 Network Timing Protocol (NTP) to provide an accurate and consistent timestamp to all intranet switches. 6 SNMP v1, v2c, and v3 and Telnet interface support delivers comprehensive in-band management, and a CLI-based management console provides detailed out-of-band management. 7 SNMPv1, SNMPv2c, and SNMPv3 Transceivers Modules( GLC-SX-MM) 1000BASE-SX SFP transceiver module for MMF, 850-nm wavelength, dual LC/PC connector. OEM ELIGIBILITY CRITERIA All active components should be from the same OEM The OEM should be an ISO-9000 and ISO certified company The OEM for the active networking components should have a 24x7 technical assistance center. The OEM for the active components should have adequate spares in the Country for their networking products. Transportation 1. Supplier is required under the Contract to transport the goods to a specified place of destination within India, defined as the Project Site, transport to such place of destination in India, including insurance and storage, as shall be specified in the Contract, shall be arranged by the Supplier, and the related costs shall be included in the Contract Price. 2. Vendor has to make Payment and arrange Octroi, Waybill etc. applicable for transportation and delivery of these equipments. Warranty 1. The successful Bidder will provide 3 years on-site comprehensive warranty for all the equipments supplied. Tax and Duty Exemption The Institute may provide necessary certificates for tax/duty exemption as applicable. Consortium If the Bidder is not a manufacturer he should provide documentary evidence (e.g. Manufacturers Authorization Form) for having tied up with all the participating agencies. Bid Currencies Bids are to be quoted in Indian Rupees only.

4 Payment: Payment shall be made in Indian Rupees for delivering, installing and commissioning the Solution. Payment will be done 100% against delivery and successful installation. Cancellation of Tender 6. The Institute may cancel the tender processing at any point of time prior to the issuance of purchase order without assigning any reason whatsoever for unforeseen and unavoidable circumstances. 7. The Institute may also cancel the tender processing for want of any participating Bidder or if all the participating Bidders fail to qualify eligibility in terms with technical or other reasons. Technical bid and commercial bid should be submitted in separate sealed envelopes mentioning the contents on it. Any Technical Bid not containing the above may be rejected. The Technical Bid should not contain any price information, such proposal will be rejected. Bill of Material (To be included in Technical Bid) The Bidder should provide Bill of Material (details of all Modules / Components of Software including those bought-out, off-the-shelf or third-party products / items required) Module-wise, in the following format. Module/Item Description Make/Model/Versi on Part Number Principal Vendor/ Manufacturer Quantity/No. Of Licenses per installation Signature of Bidder : Name : Business address : Place : Date :

5 Bill of Material (To be included in Commercial Bid) Modul e/item Make/M odel/ver sion Part Number Principa l Vendor/ Manufa cturer Quantity/No. Of Licenses per installation Unit Price Total Price without tax Tax % Tax Estimate Total Price with tax (INR) Signature of Bidder : Name : Business address : Place : Date : Quotation Address : To The Head Computer & Statistical Service Center 4 th Floor, S N Bose Bhaban Indian Statistical Institute 203 B.T. Road, Kolkata