TFT-DS-0700JMG TFT Panel. Address Talhofstr Gilching, Germany. Phone +49 (0)

Size: px

Start display at page:

Download "TFT-DS-0700JMG TFT Panel. Address Talhofstr Gilching, Germany. Phone +49 (0)"

Emily Hood
5 years ago
Views:

1 TFT-DS-0700JMG TFT Panel Address Talhofstr Gilching, Germany Phone +49 (0) Mail Web info@display-solution.com

2 Record of Revision Date Revision No. Summary Rev 1.0 was issued Page 2 of 19

3 1. Scope This data sheet is to introduce the specification of TFT-DS-0700JMG-3 active matrix TFT module. It is composed of a color TFT-LCD panel, driver ICs, FPC and a backlight unit. The 7.0 display area contains1024 x 3 (RGB) x 600 pixels. 2. Application Digital equipments which need color display, mobile navigator/video systems, tablet PC. 3. General Information Item Contents Unit Size 7.0 inch Resolution 1024 x 3 (RGB) 600 / Interface LVDS Technology type a Si TFT / Pixel pitch mm Pixel Configuration RGB stripe Outline Dimension (W x H x D) mm Active Area(W x H) mm Display Mode TM, Normally White / Backlight Type LED / Page 3 of 19

4 4. Outline Drawing Page 4 of 19

5 5. Interface signals No Symbol Description Remarks 1 VCOM Common Voltage 2 VDD Power Voltage for digital circuit 3 VDD Power Voltage for digital circuit 4 NC No connection 5 Reset Global reset pin Standby mode, Normally pulled high 6 STBYB STBYB= 1,Normally operation STBYB= 0,Timing controller, source driver will turn off, all output are High-Z 7 GND Ground 8 RXIN0- - LVDS differential data input 9 RXIN0+ +LVDS differential data input 10 GND Ground 11 RXIN1- -LVDS differential data input 12 RXIN1+ +LVDS differential data input 13 GND Ground 14 RXIN2- -LVDS differential data input 15 RXIN2+ +LVDS differential data input 16 GND Ground 17 RXCLKIN- -LVDS differential clock input 18 RXCLKIN+ +LVDS differential clock input 19 GND Ground 20 RXIN3- -LVDS differential data input 21 RXIN3+ +LVDS differential data input 22 GND Ground 23 NC No connection 24 NC No connection 25 GND Ground 26 NC No connection 27 DIMO Backlight CABC controller signal output 28 SELB 6-bit / 8-bit mode select Note 2 29 AVDD Power for Analog Circuit 30 GND Ground 31 LED- LED Cathode 32 LED- LED Cathode Page 5 of 19

6 33 L/R Horizontal inversion Note 4 34 U/D Vertical inversion Note 4 35 VGL Gate off voltage 36 CABCEN1 CABC H/W enable Note 3 37 CABCEN0 CABC H/W enable Note 3 38 VGH Gate ON Voltage 39 LED+ LED Anode 40 LED+ LED Anode Note 1: The recommended FPC connector model is FH12A-40S-0.5SH manufactured by Hirose. Note 2: If LVDS input data is 6 bits, SELB must be set to High; If LVDS input data is 8 bits, SELB must be set to Low. Note 3: When CABC_EN= 00, CABC OFF. When CABC_EN= 01, user interface image. When CABC_EN= 10, still picture. When CABC_EN= 11, moving image. When CABC off, don t connect DIMO, else connect it to backlight. Note 4: When L/R= 0, set right to left scan direction. When L/R= 1, set left to right scan direction. When U/D= 0, set top to bottom scan direction. When U/D= 1, set bottom to top scan direction. Note 5: Definition of scanning direction Refer to the figure as below: Page 6 of 19

7 6. Absolute maximum Ratings 6.1. Electrical Absolute max. ratings Parameter Symbol MIN MAX Unit Remark VDD V AVDD V Power Supply Voltage VGH V VGL V VGH VGL 40 V 6.2. Environment Conditions Item Symbol MIN MAX Unit Remark Operating Temperature TOPR Storage Temperature TSTG Page 7 of 19

8 7. Electrical Specifications 7.1 Electrical characteristics (Note 1) GND=0V, Ta=25 Item Symbol MIN TYP MAX Unit Remark VDD V Note 2 AVDD V Power Voltage VGH V VGL V Input Signal voltage VCOM 2.7 (3.7) 4.7 V Note 4 Input logic high voltage VIH 0.7VDD - VDD V Input logic low voltage VIL 0-0.3VDD V Note 3 Note 1: Be sure to apply VDD and VGL to the LCD first, and then apply VGH. Note 2: VDD setting should match the signals output voltage of customer s system board. Note 3: LVDS, Reset. Note 4: Typ. VCOM is a reference value, it must be optimized according to each LCM. Be sure to use VR. Page 8 of 19

9 7.2 Current Consumption Item Symbol MIN TYP MAX Unit Remark IGH ma VGH=20V Current for Driver IGL ma VGL=-6.8V IVDD ma VDD=3.3V IAVDD ma AVDD=11V 7.3 LED Backlight Ta=25 Item Symbol MIN TYP MAX Unit Remark Forward Current IF 160 ma Forward Voltage VF V Note 1: The LED Supply Voltage is defined by the number of LED at Ta=25 and IL=160 ma. Page 9 of 19

10 8. Command/AC Timing 8.1 AC Electrical Characteristics Parameter Symbol Min Typ Max Unit Remark Clock Frequency RxFCLK MHz Input data skew margin TRSKM 500 ps Clock high time TLVCH 4/(7* RxFCLK) ns Clock low time TLVCL 3/(7* RxFCLK) ns 8.2 Input Clock and Data Timing Diagram Page 10 of 19

11 8.3 DC Electrical Characteristics Parameter Symbol Min Typ Max Unit Remark Differential input high Threshold voltage RXVTH 0.1 V RXVCM=1.2V Differential input Low Threshold voltage RXVTL 0.1 V Input voltage range RXVIN 0 VDD 1.2+ VID /2 V Differential input common RXVCM Mode voltage VID /2 VDD 1.2 V Differential input voltage VID 0.2 v 0.6 V Differential input leakage Current RVXliz 10 v 10 ua 8.4 Timing Parameter Symbol Min Typ Max Unit Remark Clock frequency fclk MHz Horizontal display area thd 1024 DCLK HS period time th DCLK HS Blanking thb DCLK Vertical display area tvd 600 H VS period time tv H VS Blanking thb H Frame rate=60hz Page 11 of 19

12 8.5 Data Input Format Page 12 of 19

13 8.6 POWER ON/OFF SEQUENCE Page 13 of 19

14 9. Optical Specification Ta=25 Item Symbol Condition Min Typ. Max. Unit Remark Contrast Ratio CR θ= Response Time View Angles Ton Toff ΘT ΘB CR 10 ΘL ΘR ms Note1 Note2 Note1 Note3 Degree Note 4 x Brightness Note5, Chromaticity White y is on Note1 Luminance L cd/m 2 Note1 Note6 Uniformity U 80 % Note1 Note7 Page 14 of 19

15 Note 1: Definition of optical measurement system. Temperature = 25 (±3 ) LED back-light: ON, Environment brightness < 150 lx Note 2: Contrast ratio is defined as follow: Contrast Ratio = Surface Surface Luminance Luminance with with all white all black pixels pixels Note 3: Response time is defined as follow: Response time is the time required for the display to transition from black to white (Rise Time, Tr) and from white to black (Decay Time, Tf). Page 15 of 19

16 Note 4: Viewing angle range is defined as follow: Viewing angle is measured at the center point of the LCD. Note 5: Color chromaticity is defined as follow: (CIE1931) Color coordinates measured at center point of LCD. area of S area of RGB triangle 100% NTSC triangle Page 16 of 19

17 Note 6: Luminance is defined as follow: Luminance is defined as the brightness of all pixels White at the center of display area on optimum contrast. Note 7: Luminance Uniformity is defined as follow: Active area is divided into 9 measuring areas (Refer Fig. 2). Every measuring point is placed at the center of each measuring area. Uniformity (U) = Minimum Luminance( brightness ) in 9 points Maximum Luminance( brightness ) in 9 points Fig. 2 Definition of uniformity Page 17 of 19

18 10. Environmental / Reliability Tests No Test Item Condition Judgment criteria 1 High Temp Operation Ts=+70, 240hrs Per table in below 2 Low Temp Operation Ta= 20, 240hrs Per table in below 3 High Temp Storage Ta=+80, 240hrs Per table in below 4 Low Temp Storage Ta= 30, 240hrs Per table in below 5 6 High Temp & High Humidity Storage Thermal Shock (Non operation) 7 ESD (Operation) Vibration (Non operation) Shock (Non operation) Package Drop Test Ta=+40, 90% RH 240 hours min~ min, Change time:5min, 20 Cycles C=150pF,R=330Ω,5point/panel Air:±8Kv,5times; Contact:±4Kv,5times (Environment:15 ~35, 30%~60%.86Kpa~106Kpa) Frequency range:10~55hz Stroke:1.5mm Sweep:10Hz~55Hz~10Hz 2 hours for each direction of X.Y.Z. (6 hours for total) Half Sine Wave 60G 6ms, ±X,±Y,±Z 3times for each direction Height:80 cm, 1 corner, 3 edges, 6 surfaces Per table in below (polarizer discoloration is excluded) Per table in below Per table in below Per table in below Per table in below Per table in below INSPECTION Appearance Alignment of LCD Panel Electrical current Function / Display CRITERION(after test) No Crack on the FPC, on the LCD Panel No Bubbles in the LCD Panel No other Defects of Alignment in Active area Within device specifications No Broken Circuit, No Short Circuit or No Black line No Other Defects of Display Page 18 of 19

19 11. Precautions for Use of LCD Modules 11.1 Safety The liquid crystal in the LCD is poisonous. Do not put it in your mouth. If the liquid crystal touches your skin or clothes, wash it off immediately using soap and water Handling A. The LCD and touch panel is made of plate glass. Do not subject the panel to mechanical shock or to excessive force on its surface. B. Do not handle the product by holding the flexible pattern portion in order to assure the reliability C. Transparency is an important factor for the touch panel. Please wear clear finger sacks, gloves and mask to protect the touch panel from finger print or stain and also hold the portion outside the view area when handling the touch panel. D. Provide a space so that the panel does not come into contact with other components. E. To protect the product from external force, put a covering lens (acrylic board or similar board) and keep an appropriate gap between them. F. Transparent electrodes may be disconnected if the panel is used under environmental conditions where dew condensation occurs. G. Property of semiconductor devices may be affected when they are exposed to light, possibly resulting in IC malfunctions. H. To prevent such IC malfunctions, your design and mounting layout shall be done in the way that the IC is not exposed to light in actual use Static Electricity A. Ground soldering iron tips, tools and testers when they are in operation. B. Ground your body when handling the products. C. Power on the LCD module before applying the voltage to the input terminals. D. Do not apply voltage which exceeds the absolute maximum rating. E. Store the products in an anti-electrostatic bag or container. 11.4Storage A. Store the products in a dark place at +25 ±10 with low humidity (40% RH to 60% RH). Don't expose to sunlight or fluorescent light. B. Storage in a clean environment, free from dust, active gas, and solvent Cleaning A. Do not wipe the touch panel with dry cloth, as it may cause scratch. B. Wipe off the stain on the product by using soft cloth moistened with ethanol. Do not allow ethanol to get in between the upper film and the bottom glass. It may cause peeling issue or defective operation. Do not use any organic solvent or detergent other than ethanol Cautions for installing and assembling Bezel edge must be positioned in the area between the Active area and View area. The bezel may press the touch screen and cause activation if the edge touches the active area. A gap of approximately 0.5mm is needed between the bezel and the top electrode. It may cause unexpected activation if the gap is too narrow. There is a tolerance of 0.2 to 0.3mm for the outside dimensions of the touch panel and tail. A gap must be made to absorb the tolerance in the case and connector. Page 19 of 19

ASI-T-430FB2AN/D. Item Contents Unit. Size 4.3 inch. Resolution 480 (RGB) x 272 / Interface RGB / Technology type a-si TFT /

ASI-T-430FB2AN/D. Item Contents Unit. Size 4.3 inch. Resolution 480 (RGB) x 272 / Interface RGB / Technology type a-si TFT / Item Contents Unit Size 4.3 inch Resolution 480 (RGB) x 272 / Interface RGB / Technology type a-si TFT / Pixel pitch 0.198x0.198 mm Pixel Configuration RGB stripes Outline Dimension (W x H x D) 105.50x67.20x3.00