SG1560AIG-T. smarterglass.com

Size: px

Start display at page:

Download "SG1560AIG-T. smarterglass.com"

Clemence Hicks
5 years ago
Views:

1 SG1560AIG-T smarterglass.com

2 . Module Name: SG1560AIG-T Ver1.0 Record of Revision Date Revision No. Summary Rev 1.0 was issued Page 2 of 20

3 1. Scope Module Name: SG1560AIG-T Ver1.0 This data sheet is to introduce the specification of SG1560AIG-T active matrix TFT module. It is composed of a color TFT-LCD panel, driver ICs, FPC, Touch panel and a backlight unit. The 15.6 display area contains 1366(RGB) x 768 pixels. 2. Application Digital equipments which need color display, monitor and laptop. 3. General Information Item Contents Unit Size inch Resolution 1366(RGB) x 768 / Interface 6-Bit LVDS / Technology type a-si TFT / Pixel pitch 0.252x0.252 mm Pixel Configuration RGB vertical stripe Outline Dimension (W x H x D) 359.3x209.5x5.2 mm Active Area x mm Display Mode Transmissive Normally white / Backlight Type LED / Page 3 of 20

4 4. Outline Drawing Page 4 of 20

5 5. Interface signals Module Name: SG1560AIG-T Ver1.0 Connector P/N: IPEX E-12 or Eqv.; Matching connector P/N: IPEX T-01 or Eqv. Pin Symbol Description Remark 1 NC No Connection (Reserve) 2 VCCS Power Supply (3.3V typ.) 3 VCCS Power Supply (3.3V typ.) 4 VEDID DDC 3.3V power 5 NC No Connection 6 CLKEDID DDC clock 7 DATAEDID DDC data 8 Rxin0- LVDS Differential Data Input 9 Rxin0+ LVDS Differential Data Input 10 VSS Ground 11 Rxin1- LVDS Differential Data Input 12 Rxin1+ LVDS Differential Data Input 13 VSS Ground 14 RXO2- LVDS Differential Data Input 15 RXO2+ LVDS Differential Data Input 16 VSS Ground 17 RxCLK- LVDS Differential Data Input 18 RxCLK+ LVDS Differential Data Input 19 VSS Ground 20 NC No Connection(Reserve) 21 NC No Connection(Reserve) 22 VSS Ground 23 NC No Connection(Reserve) 24 NC No Connection(Reserve) 25 VSS Ground 26 NC No Connection(Reserve) 27 NC No Connection(Reserve) 28 VSS Ground 29 NC No Connection(Reserve) 30 NC No Connection(Reserve) 31 LED_GND LED Ground 32 LED_GND LED Ground 33 LED_GND LED Ground 34 NC No Connection (Reserve) 35 LED_PWM PWM Control Signal of LED Converter 36 LED_EN Enable Control Signal of LED Converter 37 NC No Connection (Reserve) 38 LED_VCCS LED Power Supply 39 LED_VCCS LED Power Supply 40 LED_VCCS LED Power Supply R0-R5, G0 G1~G5, B0, B1 B2-B5,HS,VS, DE LVDS CLK Page 5 of 20

6 6. Absolute maximum Ratings 6.1. Electrical Absolute max. ratings Module Name: SG1560AIG-T Ver1.0 Parameter Symbol MIN MAX Unit Remark Power Supply Voltage VCCS V Logic Input Voltage VIN -0.3 VCCS+0.3 V Converter Input Voltage LED_VCCS V Converter Control Signal Voltage Converter Control Signal Voltage LED_PWM V LED_EN V 6.2. Environment Conditions Item Symbol MIN MAX Unit Remark Operating Temperature TOPR Storage Temperature TSTG Note (1) (a) 90 %RH Max. (Ta <= 40 ºC). (b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC). (c) No condensation. Note (2) The temperature of panel surface should be 0 ºC min. and 60 ºC max. Relative Humidity (%RH) Temperature (ºC) Page 6 of 20

7 7. Electrical Specifications 7.1 Electrical characteristics Parameter Symbol Value Min. Typ. Max. Unit Note Power Supply Voltage VCCS V (1)- Ripple Voltage VRP mv (1)- Inrush Current IRUSH A (1),(2) Power Supply Current Mosaic ma (3)a lcc Black ma (3)b Note (1) The ambient temperature is Ta = 25 ± 2 ºC. Note (2) IRUSH: the maximum current when VCCS is rising IIS: the maximum current of the first 100ms after power-on Measurement Conditions: Shown as the following figure. Test pattern: black. VCCS rising time is 0.5ms Page 7 of 20

Note (3) The specified power supply current is under the conditions at VCCS = 3.3 V, Ta = 25 ± 2 ºC, DC Current and fv = 60 Hz, whereas a power dissipation check pattern below is displayed. a. Mosaic Pattern b.

0 V Converter Inrush Current ILEDRUSH - - 1.5 A (1) EN Control Level PWM Control Level Backlight On 2.3-5 V Backlight Off 0-0.5 V PWM High Level 2.3-5 V PWM Low Level 0-0.

8 Note (3) The specified power supply current is under the conditions at VCCS = 3.3 V, Ta = 25 ± 2 ºC, DC Current and fv = 60 Hz, whereas a power dissipation check pattern below is displayed. a. Mosaic Pattern b. Black Pattern Active Area Active Area 7.2 LED CONVERTER SPECIFICATION Parameter Symbol Value Min. Typ. Max. Unit Note Converter Input power supply voltage LED_Vccs V Converter Inrush Current ILEDRUSH A (1) EN Control Level PWM Control Level Backlight On V Backlight Off V PWM High Level V PWM Low Level V PWM Control Duty Ratio % % (2) PWM Control Permissive Ripple Voltage VPWM_pp Mv PWM Control Frequency fpwm 190-2K Hz (3) LED Power Current LED_VCCS =Typ. ILED ma (4) Note (1) ILEDRUSH: the maximum current when LED_VCCS is rising, ILEDIS: the maximum current of the first 100ms after power-on, Measurement Conditions: Shown as the following figure. LED_VCCS = Typ, Ta = 25 ± 2 ºC, fpwm = 200 Hz, Duty=100%. Page 8 of 20

9 VLED rising time is 0.5ms Note (2) If the PWM control duty ratio is less than 10%, there is some possibility that acoustic noise or backlight flash can be found. And it is also difficult to control the brightness linearity. Note (3) If PWM control frequency is applied in the range less than 1KHz, the waterfall phenomenon on the screen may be found. To avoid the issue, it s a suggestion that PWM control frequency should follow the criterion as below. PWM control frequency fpwm should be in the range (N ) f fpwm (N ) f N : Integer (N 3) f : Frame rate Note (4) The specified LED power supply current is under the conditions at LED_VCCS = Typ., Ta = 25 ± 2 ºC, fpwm = 200 Hz, Duty=100%. Page 9 of 20

7.3 BACKLIGHT UNIT Module Name: SG1560AIG-T Ver1.0 Value Parameter Symbol Unit Note Min. Typ. Max. LED Light Bar Power Supply Voltage VL 22.4 25.6 27.

10 7.3 BACKLIGHT UNIT Module Name: SG1560AIG-T Ver1.0 Value Parameter Symbol Unit Note Min. Typ. Max. LED Light Bar Power Supply Voltage VL V LED Light Bar Power Supply Current IL ma (1)(2) (Duty100%) Power Consumption PL W (3) Note (1) LED current is measured by utilizing a high frequency current meter as shown below: Note(2) For better LED light bar driving quality, it is recommended to utilize the adaptive boost converter with current balancing function to drive LED light-bar. Note (3) PL = IL VL (Without LED converter transfer efficiency) 7.4 FUNCTION BLOCK DIAGRAM Page 10 of 20

11 8. Command/AC Timing 8.1 LVDS DC SPECIFICATIONS Parameter Symbol Value Min. Typ. Max. Unit Note LVDS Differential Input High Threshold VTH(LVDS) mv (1), VCM=1.2V LVDS Differential Input Low Threshold VTL(LVDS) mv (1) VCM=1.2V LVDS Common Mode Voltage VCM V (1) LVDS Differential Input Voltage VID mv (1) LVDS Terminating Resistor RT Ohm - Note (1) The parameters of LVDS signals are defined as the following figures. 8.2 LVDS DATA FORMAT Page 11 of 20

12 8.3 COLOR DATA INPUT ASSIGNMENT The brightness of each primary color (red, green and blue) is based on the 6-bit gray scale data input for the color. The higher the binary input the brighter the color. The table below provides the assignment of color versus data input. Note 1 0: Low Level Voltage, 1: High Level Voltage Page 12 of 20

13 8.4 DISPLAY TIMING SPECIFICATIONS The input signal timing specifications are shown as the following table and timing diagram. Signal Item Symbol Min. Typ. Max. Unit Note DCLK Frequency 1/Tc MHz - Vertical Total Time TV TH - Vertical Active Display Period TVD TH - DE Vertical Active Blanking Period TVB TV-TVD 20 TV-TVD TH - Horizontal Total Time TH Tc - Horizontal Active Display Period Horizontal Active Blanking Period THD Tc - THB TH-THD 100 TH-THD Tc - Note 1 Because this module is operated by DE only mode, Hsync and Vsync are ignored. INPUT SIGNAL TIMING DIAGRAM Page 13 of 20

14 8.5 POWER ON/OFF SEQUENCE The power sequence specifications are shown as the following table and diagram. Value Symbol Min. Typ. Max. Unit Note t ms t ms t ms t ms t ms t ms t ms ta ms tb 0 10 ms tc ms td ms te ms tf ms Power On Power off Note(1) Please don t plug or unplug the interface cable when system is turned on. Note(2) Please avoid floating state of the interface signal during signal invalid period. Note(3) It is recommended that the backlight power must be turned on after the power supply for LCD and the interface signal is valid. Page 14 of 20

15 9. Optical Specification Module Name: SG1560AIG-T Ver1.0 Ta=25 Item Symbol Condition Min Typ. Max. Unit Remark Contrast Ratio CR θ= Note1 Note2 Response Time TR TF ms Note1 Note3 View Angles Chromaticity w R G B ΘT ΘB CR 10 ΘL θr x y X Y Brightness Typ-0.03 X is on Y X Y Typ+0.03 Degree Note 4 Note8 Note5, Note1 Luminance L cd/m 2 Note1 Note6 Uniformity U % Note1 Note7 Page 15 of 20

16 Note 1: Definition of optical measurement system. Temperature = 25 (±3 ) LED back-light: ON, Environment brightness < 150 lx Note 2: Contrast ratio is defined as follow: Contrast Ratio = Surface Luminancewith all whitepixels Surface Luminancewith all black pixels Note 3: Response time is defined as follow: Response time is the time required for the display to transition from black to white (Rise Time, Tr) and from white to black(decay Time, Tf). Page 16 of 20

17 Note 4: Viewing angle range is defined as follow: Viewing angle is measured at the center point of the LCD. Note 5: Color chromaticity is defined as follow: (CIE1931) Color coordinates measured at center point of LCD. area of RGB triangle S area of NTSC triangle 100% Page 17 of 20

18 Note 6: Luminance is defined as follow: Module Name: SG1560AIG-T Ver1.0 Luminance is defined as the brightness of all pixels White at the center of display area on optimum contrast. Note 7: Luminance Uniformity is defined as follow: Active area is divided into 9 measuring areas (Refer Fig. 2). Every measuring point is placed at the center of each measuring area. Uniformity (U) = MinimumLuminance( brightness) in 9 points MaximumLuminance( brightness) in 9 points Fig. 2 Definition of uniformity Page 18 of 20

19 10. Environmental / Reliability Tests No Test Item Condition Judgment criteria 1 High Temp Operation Ts=50, 120hrs Per table in below 2 Low Temp Operation Ta=0, 120hrs Per table in below 3 High Temp Storage Ta=+60, 120hrs Per table in below 4 Low Temp Storage Ta=-20, 120hrs Per table in below 5 6 High Temp & High Humidity Storage Thermal Shock (Non-operation) Ta=+50, 90% RH 120 hours min~ min, Change time:5min, 10 Cycles Per table in below (polarizer discoloration is excluded) Per table in below 7 ESD (Operation) C=150pF, R=330Ω,5points/panel Air:±8KV, 5times; Contact:±4KV, 5 times; Per table in below 8 Vibration (Non-operation) Frequency range:10~55hz, Stroke:1.5mm Sweep:10Hz~55Hz~10Hz 2 hours for each direction of X.Y.Z. Per table in below 9 10 Shock (Non-operation) Package Drop Test 60G 6ms, ±X,±Y,±Z 3times, for each direction Height:80 cm, 1 corner, 3 edges, 6 surfaces Per table in below Per table in below INSPECTION Appearance Alignment of LCD Panel Electrical current Function / Display CRITERION(after test) No Crack on the FPC, on the LCD Panel No Bubbles in the LCD Panel No other Defects of Alignment in Active area Within device specifications No Broken Circuit, No Short Circuit or No Black line No Other Defects of Display Page 19 of 20

20 11. Precautions for Use of LCD Modules Module Name: SG1560AIG-T Ver Safety The liquid crystal in the LCD is poisonous. Do not put it in your mouth. If the liquid crystal touches your skin or clothes, wash it off immediately using soap and water Handling A. The LCD and touch panel is made of plate glass. Do not subject the panel to mechanical shock or to excessive force on its surface. B. Do not handle the product by holding the flexible pattern portion in order to assure the reliability C. Transparency is an important factor for the touch panel. Please wear clear finger sacks, gloves and mask to protect the touch panel from finger print or stain and also hold the portion outside the view area when handling the touch panel. D. Provide a space so that the panel does not come into contact with other components. E. To protect the product from external force, put a covering lens (acrylic board or similar board) and keep an appropriate gap between them. F. Transparent electrodes may be disconnected if the panel is used under environmental conditions where dew condensation occurs. G. Property of semiconductor devices may be affected when they are exposed to light, possibly resulting in IC malfunctions. H. To prevent such IC malfunctions, your design and mounting layout shall be done in the way that the IC is not exposed to light in actual use Static Electricity A. Ground soldering iron tips, tools and testers when they are in operation. B. Ground your body when handling the products. C. Power on the LCD module before applying the voltage to the input terminals. D. Do not apply voltage which exceeds the absolute maximum rating. E. Store the products in an anti-electrostatic bag or container. 11.4Storage A. Store the products in a dark place at +25 ±10 with low humidity (40% RH to 60% RH). Don't expose to sunlight or fluorescent light. B. Storage in a clean environment, free from dust, active gas, and solvent Cleaning A. Do not wipe the touch panel with dry cloth, as it may cause scratch. B. Wipe off the stain on the product by using soft cloth moistened with ethanol. Do not allow ethanol to get in between the upper film and the bottom glass. It may cause peeling issue or defective operation. Do not use any organic solvent or detergent other than ethanol Cautions for installing and assembling Bezel edge must be positioned in the area between the Active area and View area. The bezel may press the touch screen and cause activation if the edge touches the active area. A gap of approximately 0.5mm is needed between the bezel and the top electrode. It may cause unexpected activation if the gap is too narrow. There is a tolerance of 0.2 to 0.3mm for the outside dimensions of the touch panel and tail. A gap must be made to absorb the tolerance in the case and connector. Page 20 of 20

ASI-T-430FB2AN/D. Item Contents Unit. Size 4.3 inch. Resolution 480 (RGB) x 272 / Interface RGB / Technology type a-si TFT /

ASI-T-430FB2AN/D. Item Contents Unit. Size 4.3 inch. Resolution 480 (RGB) x 272 / Interface RGB / Technology type a-si TFT / Item Contents Unit Size 4.3 inch Resolution 480 (RGB) x 272 / Interface RGB / Technology type a-si TFT / Pixel pitch 0.198x0.198 mm Pixel Configuration RGB stripes Outline Dimension (W x H x D) 105.50x67.20x3.00