Preliminary PRODUCT MANUAL. PXM-MiniPCIe SUMIT-ISM Module with MiniPCIe and USB. WinSystems. WinSystems, Inc. 715 Stadium Drive Arlington, TX 76011

Transcription

1 WinSystems PXM-MiniPCIe SUMIT-ISM Module with MiniPCIe and USB PRODUCT MANUAL WinSystems, Inc. 715 Stadium Drive Arlington, TX

2 REVISION HISTORY P/N Date Code REV Level ECO Number A PRODUCT MANUAL PXM-MiniPCIe 2

3 TABLE OF CONTENTS Visual Index - Top View (Connectors) 5 Visual Index - Top View (Jumpers & LEDs) 6 Visual Index - Bottom View (Connectors & Jumpers) 7 Jumper Reference 8 INTRODUCTION 11 FEATURES 11 System 11 FUNCTIONALITY 12 MiniPCIe Cards 12 RF Connectors 12 Status Indicators 12 User Indentity Module (UIM) Connector 12 CONNECTOR REFERENCE 13 POWER 13 D2 (Power LED +5VSB), D1 (Power LED +5V) 13 USB 13 J8, J9 - USB 13 PC/104 BUS INTERFACE 14 J16 - PC/ SUMIT TM INTERFACE 15 J1, J2 - SUMIT 15 MiniPCI EXPRESS 16 J11 - MiniPCIe 16 CABLES 17 SOFTWARE DRIVERS & EXAMPLES 18 MECHANICAL DRAWING 19 APPENDIX 20 WARRANTY INFORMATION PRODUCT MANUAL PXM-MiniPCIe

4 This page has been left intentionally blank PRODUCT MANUAL PXM-MiniPCIe 4

5 Visual Index - Top View (Connectors) J7 SIM Card J2 SUMIT-B J1 SUMIT-A J16 J16 PC/104 (C/D) PC/104 (A/B) J12 MiniPCIe Antennae J13 MiniPCIe Antennae RESERVED - D7, D8 NOTE: The reference line to each component part has been drawn to Pin 1, and is also highlighted with a square, where applicable PRODUCT MANUAL PXM-MiniPCIe 5

6 Visual Index - Top View (Jumpers & LEDs) D2 Power LED +5VSB D1 Power LED +5V J4 USB (0/1) D4 USB0 Power J3 W_Disable D3 PCIExpress Status Indicator 2 J5 USB2 Power D5 PCIExpress Status Indicator 3 D6 PCIExpress Status Indicator 1 J15 J11 MiniPCIe Socket J14 D8 D7 J10 USB (1/3) J6 USB (0/2) J8 USB2 (2.0) J9 USB3 (2.0) D9 USB1 Power RESERVED - D7, D8 NOTE: The reference line to each component part has been drawn to Pin 1, and is also highlighted with a square, where applicable PRODUCT MANUAL PXM-MiniPCIe 6

7 Visual Index - Bottom View (Connectors & Jumpers) J100 SD100 J100 J101 J101 RESERVED - D7, D8 NOTE: The reference line to each component part has been drawn to Pin 1, and is also highlighted with a square, where applicable PRODUCT MANUAL PXM-MiniPCIe 7

8 Jumper Reference Jumpering Options to be determined PRODUCT MANUAL PXM-MiniPCIe 8

9 Jumper Reference (cont d) Jumpering Options to be determined PRODUCT MANUAL PXM-MiniPCIe 9

10 This page has been left intentionally blank PRODUCT MANUAL PXM-MiniPCIe 10

11 INTRODUCTION This manual is intended to provide the necessary information regarding configuration and usage of the PXM-MiniPCIe SUMIT-ISM module. WinSystems maintains a Technical Support Group to help answer questions not adequately addressed in this manual. Contact Technical Support at (817) , Monday through Friday, between 8 AM and 5 PM Central Standard Time (CST). FEATURES SUMIT Interface Revision 1.5 MiniPCIe Full and Half size PCIe mini card support PCIe and USB 2.0 interface support through SUMIT AB Multiple antennae support (via 2 RF connectors) SIM card socket Power Onboard power supplies USB 2 USB 2.0 ports Overcurrent and inrush protection for each port Automatic USB signal lane shifting LED status provided for each port Industrial Operating Temperature -40 C to 85 C Form Factor 3.6 x 3.8 (90 mm x 96 mm) Standard RoHS compliant PC/104 and SUMIT expansion connectors Activity status LEDs on-board PS/2 Keyboard and Mouse System The PXM-MiniPCIe is a SUMIT-ISM module that supports both a MiniPCIe card and two USB ports. It provides expansion of additional functions such as a/g wireless, WLAN, and othe rhigh performance functions developed for mobile computing environments. The two USB 2.0 expansion ports support tethered aplications such as storage, imaging, and video, as well as slower dvices such as mouse, keyboard, floppy disk, USB keys, etc PRODUCT MANUAL PXM-MiniPCIe 11

12 FUNCTIONALITY MiniPCIe Cards The MiniCard is a small form factor board used to implement the PCI Express interface on notebook computers for additional I/O functions. The PCI Express MiniCard socket supports two primary system bus interfaces: PCI Express x1 and USB 2.0, and provides connections to many other functions. RF Connectors Two right angle RF connectors are on the PXM-MiniiPCIe board s edge, enabling convenient connection to the MiniPCIe card from a regular coax cable from an external antenna. Status Indicators Three inidividual LEDs provide a visual status of the installed wireless card s function. User Indentity Module (UIM) Connector A UIM contains parameters necessary for the WWAN device s operation in a wireless wide area radio environment. The W_DISABLE# signal is supported to disable radio operation. This signal is wired to a connector on the edge of the PXM-MiniPCIe module PRODUCT MANUAL PXM-MiniPCIe 12

13 POWER CONNECTOR REFERENCE The +5V input power and ground is supplied from the SUMIT A and B, and PC/104 connectors, located at J1, J2, and J16, respectively. There is a +5V to 3.3V regulator and a +5V to 1.5V regulator on-board to supply power to MiniPCIe cards. Power is applied to the PXM-MiniPCIe via the connector at J15. D2 (Power LED +5VSB), D1 (Power LED +5V) Visual Index Visual Index LEDs located at D2 (Power LED +5VSB), D1 (Power LED +5V) indicate the state of the system. NOTE: D2 and D1 will always be illuminated during normal operation. When using an ATX power supply and only D2 is illuminated, the system is in suspend mode. USB J8, J9 - USB USBPWR0 D0+ J USBPWR1 D1+ D2 GREEN +5VSB D1 RED VCC (+5V) USBPWR2 J USBPWR3 Up to two USB cables may be attached to the PXM-MiniPCIe via the connectors for a total of four USB 2.0 ports. These are terminated to an 8-pin, 2 mm connector at J8 and J9. An adapter cable CBL-356-G is available from WinSystems for connection. Two additional USB ports are available for expansion on the SUMIT interface. D3- D2- D2+ D1- D0- D3+ Visual Index PRODUCT MANUAL PXM-MiniPCIe 13

14 PC/104 BUS INTERFACE J16 - PC/104 The PC/104 bus is electrically equivalent to the 16-bit ISA bus. Standard PC/104 I/O cards can be populated on PXM-MiniPCIe s connectors, located at J16. The interface does not support hot swap capability. The PC/104 bus connector pin definitions are provided here for reference. Refer to the PC/104 Bus Specification for specific signal and mechanical specifications. Visual Index J16 J16 D0 MEMCS16# D1 IOCS16# D2 IRQ10 D3 IRQ11 D4 IRQ12 D5 IRQ15 D6 IRQ14 D7 DACK0# D8 DRQ0 D9 DACK5# D10 DRQ5 D11 DACK6# D12 DRQ6 D13 DACK7# D14 DRQ7 D15 +5V D16 MASTER# D17 D18 D19 C18 C19 # = Active Low Signal C0 C1 SBHE# C2 LA23 C3 LA22 C4 LA21 C5 LA20 C6 LA19 C7 LA18 C8 LA17 C9 MEMR# C10 MEMW# C11 SD8 C12 SB9 C13 SD10 C14 SD11 C15 SD12 C16 SD13 C17 SD14 SD15 KEY IOCHK# A1 SD7 A2 SD6 SD5 SD4 SD3 SD2 SD1 SD0 A3 A4 A5 A6 A7 A8 A9 IOCHRDY A10 AEN A11 SA19 A12 SA18 A13 SA17 A14 SA16 A15 SA15 A16 SA14 A17 SA13 A18 SA12 A19 SA11 A20 SA10 A21 SA9 A22 SA8 A23 SA7 A24 SA6 A25 SA5 A26 SA4 A27 SA3 A28 SA2 A29 SA1 A30 SA0 A31 A32 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 B24 B25 B26 B27 B28 B29 B30 B31 B32 RESET +5V IRQ -5V DRQ2-12V SRDY# +12V KEY SMEMW# SMEMR# IOW# IOR# DACK3# DRQ3 DACK1# DRQ1 REFRESH# BCLK IRQ7 IRQ6 IRQ5 IRQ4 IRQ3 DACK2# TC BALE +5V OSC NOTES: 1. Rows C and D are not required on 8-bit modules. 2. B10 and C19 are key locations. WinSystems uses key pins as connections to. 3. Signal timing and function are as specified in ISA specification. 4. Signal source/sink current differ from ISA values PRODUCT MANUAL PXM-MiniPCIe 14

15 SUMIT TM INTERFACE J1, J2 - SUMIT Visual Index J1 J2 5V 3.3V_1 3.3V_2 EXPCD_REQ# EXPCD_PRSNT# USB_OC#0/1 USB_OC#0/1 5V_2 USB3+ USB3-5V_3 USB2+ USB2-5V_4 USB1+ USB1-5V_5 USB0+ USB0- _1 A_PETp0 A_PETn0 _2 PERST# WAKE# A_CLKn 5V_ V_3 5V_ V SMB_DATA SMB_CLK SMB_ALERT SPI_DO SPI_DI SPI_CLK SPI_CS0 SPI_CS1 RESERVED_5 LPC_DRQ LPC_AD0 LPC_AD1 LPC_AD2 LPC_AD3 LPC_FRAME# SERIRQ# LPC_PRSNT#/ _3 A_PERp0 A_PERn0 5V B_PETp0 B_PETn0 C_CLKp C_CLKn CPRSNT#/ C_PETp0 C_PETn B_PERp0 B_PERn0 BPRST#/ B_CLKp B_CLKn C_PERp0 C_PERn0 The PXM-MiniPCIe has a SUMIT-A connector which allows for multiple I/O modules to be stacked on top of a host module. SUMIT-A is located at J1. A second SUMIT-B connector, located at J2. Their pinouts for J1 and J2 are _2 C_PETp1 C_PETn listed above. Refer to the SUMIT Specification for more information on the SUMIT Interface C_PERp C_PERp C_PERp3 36 C_PERn3 CLK_33MHz _ PERST# WAKE# RESERVED RESERVED 5V_ RESERVED APRSNT RV_ V 48 A_CLKp 5V_ V_2 52 _4 5V_ V_7 C_PETp2 C_PETn2 _3 C_PETp3 C_PETn3 C_PERn1 C_PERn PRODUCT MANUAL PXM-MiniPCIe 15

16 MiniPCI EXPRESS J11 - MiniPCIe The PXM-MiniPCIe includes a MiniPCIExpress socket at J11. Though the socket can support other devices, it is most often used to add wireless Ethernet cards from Broadcom, Foxconn, (Atheros), or others. NOTE: Intel boards are not supported by the PXM-MiniPCIe. Visual Index Pin Name Pin Name 2 3.3Vaux 1 WAKE# 4 3 COEX V 5 COEX2 8 UIM_PWR 7 CLKREQ# 10 UIM_DATA 9 12 UIM_CLK 11 REFCLK- 14 UIM_RESET 13 REFCLK+ 16 UIM_VPP 15 Mechanical Key Reserved (UIM_C8) 20 W_DISABLE# 19 Reserved (UIM_C4) 22 PERST# Vaux 23 PERn PERp V SMB_CLK SMB_DATA 31 PETn PETp0 36 USB_D USB_D Vaux 42 LED_WWAN# Vaux 44 LED_WLAN# LED_WPAN# 45 Reserved V 47 Reserved Reserved Vaux 51 Reserved PRODUCT MANUAL PXM-MiniPCIe 16

17 CABLES Cables to be determined PRODUCT MANUAL PXM-MiniPCIe 17

18 SOFTWARE DRIVERS & EXAMPLES Software Drivers & Examples to be determined PRODUCT MANUAL PXM-MiniPCIe 18

19 MECHANICAL DRAWING Mechanical Drawing to be determined PRODUCT MANUAL PXM-MiniPCIe 19

20 APPENDIX To be included in later manual versions PRODUCT MANUAL PXM-MiniPCIe 20

21 WARRANTY INFORMATION ( WinSystems warrants to Customer that for a period of two (2) years from the date of shipment any Products and Software purchased or licensed hereunder which have been developed or manufactured by WinSystems shall be free of any material defects and shall perform substantially in accordance with WinSystems specifications therefore. With respect to any Products or Software purchased or licensed hereunder which have been developed or manufactured by others, WinSystems shall transfer and assign to Customer any warranty of such manufacturer or developer held by WinSystems, provided that the warranty, if any, may be assigned. Notwithstanding anything herein to the contrary, this warranty granted by WinSystems to the Customer shall be for the sole benefit of the Customer, and may not be assigned, transferred or conveyed to any third party. The sole obligation of WinSystems for any breach of warranty contained herein shall be, at its option, either (i) to repair or replace at its expense any materially defective Products or Software, or (ii) to take back such Products and Software and refund the Customer the purchase price and any license fees paid for the same. Customer shall pay all freight, duty, broker s fees, insurance charges for the return of any Products or Software to WinSystems under this warranty. WinSystems shall pay freight and insurance charges for any repaired or replaced Products or Software thereafter delivered to Customer within the United States. All fees and costs for shipment outside of the United States shall be paid by Customer. The foregoing warranty shall not apply to any Products of Software which have been subject to abuse, misuse, vandalism, accidents, alteration, neglect, unauthorized repair or improper installations. THERE ARE NO WARRANTIES BY WINSYSTEMS EXCEPT AS STATED HEREIN, THERE ARE NO OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN NO EVENT SHALL WINSYSTEMS BE LIABLE FOR CONSEQUENTIAL, INCIDENTIAL OR SPECIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF DATA, PROFITS OR GOODWILL. WINSYSTEMS MAXIMUM LIABILITY FOR ANY BREACH OF THIS AGREEMENT OR OTHER CLAIM RELATED TO ANY PRODUCTS, SOFTWARE, OR THE SUBJECT MATTER HEREOF, SHALL NOT EXCEED THE PURCHASE PRICE OR LICENSE FEE PAID BY CUSTOMER TO WINSYSTEMS FOR THE PRODUCTS OR SOFTWARE OR PORTION THEREOF TO WHICH SUCH BREACH OR CLAIM PERTAINS. WARRANTY SERVICE 1. To obtain service under this warranty, obtain a return authorization number. In the United States, contact the WinSystems Service Center for a return authorization number. Outside the United States, contact your local sales agent for a return authorization number. 2. You must send the product postage prepaid and insured. You must enclose the products in an anti-static bag to protect from damage by static electricity. WinSystems is not responsible for damage to the product due to static electricity PRODUCT MANUAL PXM-MiniPCIe 21