OPERATIONS MANUAL PPM-WIRELESS

Transcription

1 OPERATIONS MANUAL PPM-WIRELESS NOTE: This manual has been designed and created for use as part of the WinSystems Technical Manuals CD and/or the WinSystems web site. If this manual or any portion of the manual is downloaded, copied or ed, the links to additional information (i.e. software, cable drawings) will be inoperable. WinSystems reserves the right to make changes in the circuitry and specifications at any time without notice. Copyright 2008 by WinSystems. All Rights Reserved.

2 REVISION HISTORY P/N B ECO Number Date Code Rev Level ORIGINATED A A A A.3

3 Table of Contents Visual Index Quick Reference Top View - Connectors and Jumpers i i Introduction 1 General Information 1 Features 1 Functional Capability 2 Configuration Options 2 minipci Device Interface (J5) 3 Software 4 RF Antenna Connection 4 Wireless Network Architecture 4 minipci Device Interrupt Configuration (J1) 4 PC/104-Plus Bus Slot Selection (J9) 5 PC/104-Plus Bus Interface (J4) 5 PC/104 Bus Interface (J8) 6 On-board Voltage Regulator (J10) 7 Development Kit 7 Jumper Reference 8 Mechanical Drawing 10 Specifications 11 WARRANTY REPAIR INFORMATION 12

4 Visual Index Quick Reference Top View - Connectors and Jumpers For the convenience of the user, a copy of the Visual Index has been provided with direct links to connector and jumper configuration data. J8 PC/104 Bus Connector J9 PC/104-Plus Bus Slot Selection J2 Main Antenna J3 Main Antenna Cable J7 Auxiliary Antenna J6 Auxiliary Antenna Cable J1 minipci Device Interrupt J10 Voltage Selection J4 PC/104-Plus Bus Connector J5 minipci Device Interface NOTE: The reference line to each component part has been drawn to Pin 1, where applicable. Pin 1 is also highlighted with a red square, where applicable OPERATIONS MANUAL PPM-WIRELESS i

5 Introduction This manual is intended to provide the necessary information regarding configuration and usage of the PPM-WIRELESS board. WinSystems maintains a Technical Support Group to help answer questions regarding usage, or programming of the board. For answers to questions not adequately addressed in this manual, contact Technical Support at (817) between 8 A.M. and 5 P.M. Central Standard Time. General Information Features Wireless Module IEEE module supported Supports Intel, Broadcom, Atheros, and similar minipci modules Power Onboard 3.3V regulator (allows +5V board operation) Industrial Operating Temperature Range -40 C to 85 C Form Factor PC/104-Plus-compliant 3.60 in x 3.80 in (90 mm x 96 mm) WinSystems PPM-WIRELESS is a PC/104-Plus module that supports b/g wireless communications. This technology provides a high-speed, industrial data network based upon minipci wireless modules and Ethernet utilizing a TCP/IP protocol stack. This means that the standard CAT5 Ethernet cable is replaced by a radio channel which simplifies cabling installation and configuration issues. Lack of cabling makes moves, additions, and changes easy for installed networks. Also, the portable nature of wireless networks lets engineers preconfigure and troubleshoot entire networks before installing them at remote locations. Once configured, a system can be moved from place to place with little or no modification. Applications include high bandwidth remote communications, MPEG video streaming, mobile environments, remote surveillance, and protocol conversion. WARNING: Compliance with Part 15 of the FCC rules is fully the responsibility of the customer OPERATIONS MANUAL PPM-WIRELESS 1

6 Functional Capability The PPM-WIRELESS is a small, PC/104-Plus compliant module that measures only 3.60 in x 3.80 in (90 mm x 96 mm). The PPM-Wireless can be stacked on top of a host PC/104- Plus, EPIC, or EBX single board computer. On board the PPM-WIRELESS are the interface electronics, a minipci connector, power supply, and antenna connector. WinSystems PPM-WIRELESS converts the PC/104-Plus PCI signals into minipci-compatible signals. A minipci card is a small version of a standard desktop PCI card with the same features and functionality of a normal PCI card but at about one quarter the size. Ideally suited for embedded applications, the minipci card measures only 51 mm x 60 mm. The PPM-WIRELESS supports the same minipci cards used worldwide in laptop computers. The operating temperature range -40 C to 85 C does not apply to the user-populated mini-pci card. Configuration Options The PPM-Wireless is shipped with an empty minipci socket (J5) so that a user can install their own cards from Intel, Broadcom, Foxconn (Atheros), and others. It is also available in a kit which includes an Intel PRO/Wireless 2200BG mini-pci card installed by WinSystems. Visual Index An Intel PRO/Wireless 2200BG card is a standards-based, Wi-Fi Certified wireless local area network (WLAN) solution that allows up to 54 million bits of data to be transferred per second. It is designed to maintain high throughput at longer ranges depending upon the type of antenna used. The Intel PRO/Wireless 2200BG is software upgradeable to provide future security and other service enhancements. The Intel PRO/Wireless 2200BG network connection fully supports today s security standards such as Wi-Fi Protected Access (WPA) and can be upgraded via software downloads for future security standards such as when i becomes available OPERATIONS MANUAL PPM-WIRELESS 2

7 minipci Device Interface (J5) Visual Index PIN SIGNAL PIN SIGNAL PIN SIGNAL PIN SIGNAL 1 TIP 2 RING V 64 FRAME KEY KEY 65 CLKRUN# 66 TRDY# 3 8PMJ-3 4 8PMJ-1 67 SERR# 68 STOP# 5 8PMJ-6 6 8PMJ-2 69 GROUND V 7 8PMJ-7 8 8PMJ-4 71 PERR# 72 DEVSEL# 9 8PMJ PMJ-5 73 C/BE(1)# 74 GROUND 11 LED_GRN+ 12 LED_YEL+ 75 AD(14) 76 AD(15) 13 LED_GRN- 14 LED_YEL- 77 GROUND 78 AD(13) 15 CHSGND 16 RESERVED 79 AD(12) 80 AD(11) 17 INTB# 18 5V 81 AD(10) 82 GROUND V 20 INTA# 83 GROUND 84 AD(09) 21 RESERVED 22 RESERVED 85 AD(08) 86 C/BE(0)# 23 GROUND V AUX 87 AD(07) V 25 CLK 26 RST# V 90 AD(06) 27 GROUND V 91 AD(05) 92 AD(04) 29 REQ# 30 GNT# 93 RESERVED 94 AD(02) V 32 GROUND 95 AD(03) 96 AD(00) 33 AD(31) 34 PME# 97 5V 98 RESERVED_WIP 5 35 AD(29) 36 RESERVED 99 AD(01) 100 RESERVED_WIP 5 37 GROUND 38 AD(30) 101 GROUND 102 GROUND 39 AD(27) V 103 AC_SYNC 104 M66EN 41 AD(25) 42 AD(28) 105 AC_SRDATA_IN 106 AC_SDATA_OUT 43 RESERVED 44 AD(26) 107 AC_BIT_CLK 108 AC_CODEC_ID0# 45 C/BE(3)# 46 AD(24) 109 AC_CODEC_ID1# 110 AC_RESET# 47 AD(23) 48 IDSEL 111 MON_AUDIO_MON 112 RESERVED 49 GROUND 50 GROUND 113 AUDIO_GND 114 GROUND 51 AD(21) 52 AD(22) 115 SYS_AUDIO_OUT 116 SYS_AUDIO_IN 53 AD(19) 54 AD(20) 117 SYS_AUDIO_OUT_GND 118 SYS_AUDIO_IN_GND 55 GROUND 56 PAR 119 AUDIO_GND 120 AUDIO_GND 57 AD(17) 58 AD(18) 121 RESERVED 122 MPCIACT# 59 C/BE(2)# 60 AD(16) 123 VCC5VA VAUX 61 IRDY# 62 GROUND # = ACTIVE LOW SIGNAL OPERATIONS MANUAL PPM-WIRELESS 3

8 Software Normally cards are automatically recognized by operating systems such as Windows XP. The individual minipci card manufacturer will typically have drivers available with their card and/or at their website. Please contact them directly for specific operating systems that their card will support. RF Antenna Connection The PPM-WIRELESS has a reverse polarized (RP) SMA external connector to enable the selection of an antenna having characteristics best suited for the application. Typical indoor range for an omni-directional is 100 ft 54 Mbps or 300 ft 1 Mbps; however, it is dependent upon the type and placement of the antenna, and any sources of interference in the environment. Visual Index The most common antenna type for wireless LANs is omni-directional, but some applications may require directional radiation patterns. A second RF connector can be added to the PPM-Wireless board as a factory option to support a diversity antenna configuration for improved performance. Wireless Network Architecture Users need very little new information to take advantage of wireless LANs (WLAN). Because the wireless nature of a WLAN is transparent to a user s network operating system (NOS), applications work the same as they do on LANs using cables. The protocol can be deployed in ad hoc mode for peer-to-peer communication between wireless stations or in infrastructure mode enabling communication between stations and access points (APs). minipci Device Interrupt Configuration (J1) J1 configures device interrupts for the minipci interface. When a Single Function minipci device is present, J1 should be jumpered 1-2. For Dual Function devices, jumper J1 1-2 and 3-4. Visual Index J1 J1 Single function minipci device Dual function minipci device OPERATIONS MANUAL PPM-WIRELESS 4

9 PC/104-Plus Bus Slot Selection (J9) The PPM-WIRELESS provides a high-performance, 32-bit PCI interface using the PC/104-Plus bus. Multiple PC/104-Plus boards can be installed and supported on a single stack. Visual Index J9 is used to select the slot number of the PCI connection for the board. Each PC/104-Plus board installed in a system must have a unique slot assignment and must not conflict with any PCI slot assignments on the CPU card. The jumper settings for J9 are shown here: Slot 1 Slot 2 Slot 3 Slot 4 There is also a PC/104 connector on the PPM-WIRELESS board to support mixed PC/104 and PC/104-Plus modules on a stack. No control or data signals are wired to the PC/104 connector. It simply feeds the signals through the connector to the next module in a stack. PC/104-Plus Bus Interface (J4) PIN A B C D 1 GND RESERVED +5V AD00 2 VI/O AD02 AD01 +5V 3 AD05 GND AD04 AD03 4 C/BE0# AD07 GND AD06 5 GND AD09 AD08 GND 6 AD11 VI/O AD10 M66EN 7 AD14 AD13 GND AD V C/BE1# AD V 9 SERR# GND RESERVED PAR 10 GND PERR# +3.3V RESERVED 11 STOP# +3.3V LOCK# GND V TRDY# GND DEVSEL# 13 FRAME# GND IRDY# +3.3V 14 GND AD V C/BE2# 15 AD V AD17 GND 16 AD21 AD20 GND AD V AD23 AD V 18 IDSEL0 GND IDSEL1 IDSEL2 19 AD24 C/BE3# VI/O IDSEL3 20 GND AD26 AD25 GND 21 AD29 +5V AD28 AD V AD30 GND AD31 23 REQ0# GND REQ1# VI/O 24 GND REQ2# +5V GNT0# 25 GNT1# VI/O GNT2# GND 26 +5V CLK0 GND CLK1 27 CLK2 +5V CLK3 GND 28 GND INTD# +5V RST# V INTA# INTB# INTC# 30-12V REQ3# GNT3# GND/3.3V KEY Visual Index # = ACTIVE LOW SIGNAL OPERATIONS MANUAL PPM-WIRELESS 5

10 PC/104 Bus Interface (J8) J8 PC/104 BUS CONNECTOR Visual Index GND D0 o o C0 MEMCS16# D1 o o C1 IOCS16# D2 o o C2 IRQ10 D3 o o C3 IRQ11 D4 o o C4 IRQ12 D5 o o C5 IRQ15 D6 o o C6 IRQ14 D7 o o C7 DACK0# D8 o o C8 DRQ0 D9 o o C9 DACK5# D10 o o C10 DRQ5 D11 o o C11 DACK6# D12 o o C12 DRQ6 D13 o o C13 DACK7# D14 o o C14 DRQ7 D15 o o C15 +5V D16 o o C16 MASTER# D17 o o C17 GND D18 o o C18 GND D19 o o C19 # = Active Low Signal GND SBHE# LA23 LA22 LA21 LA20 LA19 LA18 LA17 MEMR# MEMW# SD8 SD9 SD10 SD11 SD12 SD13 SD14 SD15 KEY IOCHK# A1 o o B1 SD7 A2 o o B2 SD6 A3 o o B2 SD5 A4 o o B4 SD4 A5 o o B5 SD3 A6 o o B6 SD2 A7 o o B7 SD1 A8 o o B8 SD0 A9 o o B9 IOCHRDY A10 o o B10 AEN A11 o o B11 SA19 A12 o o B12 SA18 A13 o o B13 SA17 A14 o o B14 SA16 A15 o o B15 SA15 A16 o o B16 SA14 A17 o o B17 SA13 A18 o o B18 SA12 A19 o o B19 SA11 A20 o o B20 SA10 A21 o o B21 SA9 A22 o o B22 SA8 A23 o o B23 SA7 A24 o o B24 SA6 A25 o o B25 SA5 A26 o o B26 SA4 A27 o o B27 SA3 A28 o o B28 SA2 A29 o o B29 SA1 A30 o o B30 SA0 A31 o o B31 GND A32 o o B32 GND RESET +5V IRQ9-5V DRQ2-12V SRDY# +12V KEY SMEMW# SMEMR# IOW# IOR# DACK3# DRQ3 DACK1# DRQ1 REFRESH# BCLK IRQ7 IRQ6 IRQ5 IRQ4 IRQ3 DACK2# TC BALE +5V OSC GND GND NOTES: 1. Rows C and D are not required on 8-bit modules. 2. B10 and C19 are key locations. WinSystems uses key pins as connections to GND. 3. Signal timing and function are as specified in ISA specification. 4. Signal source/sink current differ from ISA values OPERATIONS MANUAL PPM-WIRELESS 6

11 On-board Voltage Regulator (J10) An on-board 3.3V regulator allows the board to be used with either +5V or 3.3V PC/104-Plus processor boards. J10 routes the voltage sources supplied from the PC/104-Plus bus to the on-board Vcc circuit. Refer to the jumpering options shown below to route the appropriate voltage. When the supplied voltage from the PC/104-Plus bus connector is +3.3V, connecting J10 pins 2-4 routes +3.3V directly to the PPM-WIRELESS Vcc circuit. When +5V are supplied, jumpering pins 1-2 routes +5V to an on-board DC regulator, which converts the +5V source to +3.3V for Vcc. Visual Index J10 J10 +5V +3.3V Most minipci wireless cards will require 3.3 VDC to be provided for proper operation. The PPM-WIRELESS card can provide this 3.3 VDC supply voltage either directly from the PC/104-Plus 3.3 VDC supply or by using the 5 VDC supply from the PC/104-Plus bus and regulating the supply down to 3.3 VDC through an on-board regulator. Jumper J10 is used to make this selection. Jumpering options based on either the +5V or +3.3V operation are provided above. Development Kit A development kit is available that includes the PPM-WIRELESS, Intel minipci b/g module, antenna, and cables. It provides a reliable, quick start kit to use during initial product design. Additional information about this kit and available software drivers is listed on the WinSystems website OPERATIONS MANUAL PPM-WIRELESS 7

12 Jumper Reference Drawings Only - for more detailed informaiton on these parts, refer to the descriptions shown previously in this manual. J8 PC/104 Bus Connector J9 PC/104-Plus Bus Slot Selection J2 Main Antenna J3 Main Antenna Cable J7 Auxiliary Antenna J6 Auxiliary Antenna Cable J1 minipci Device Interrupt J10 Voltage Selection J4 PC/104-Plus Bus Connector J5 minipci Device Interface NOTE: The reference line to each component part has been drawn to Pin 1, where applicable. Pin 1 is also highlighted with a red square, where applicable OPERATIONS MANUAL PPM-WIRELESS 8

13 PC/104-Plus Bus Slot Selection (J9) J9 is used to select the slot number of the PCI connection for the board. Slot 1 Slot 2 Slot 3 Slot 4 Onboard Voltage Regulator (J10) When the supplied voltage from the PC/104-Plus bus connector is +3.3V, connecting J10 pins 2-4 routes +3.3V directly to the PPM-WIRELESS Vcc circuit. When +5V are supplied, jumpering pins 1-2 routes +5V to an on-board DC regulator, which converts the +5V source to +3.3V for Vcc. J10 J10 +5 V +3.3 V minipci Device Interrupt Configuration (J1) When a Single Function minipci device is present, J1 should be jumpered 1-2. For Dual Function devices, jumper J1 1-2 and 3-4. J1 J1 Single function minipci device Dual function minipci device OPERATIONS MANUAL PPM-WIRELESS 9

14 Mechanical Drawing OPERATIONS MANUAL PPM-WIRELESS 10

15 Specifications Electrical Power Requirements :VCC +5V Mechanical Dimensions Weight Connectors RF minipci PC/104-Plus PC/104 :3.6 in x 3.8 in (90 mm x 96 mm) :3.0 oz (84 grams) approximate weight :RP-SMA :124-pin, 0.8 mm :120-pin (4 x 30;2 mm) stackthrough with shrouded header :16-bit stackthrough (feed through only) Environmental Operating Temperature :-40 C to 85 C Non-condensing relative Humidity :5% to 95% MTBF : OPERATIONS MANUAL PPM-WIRELESS 11

16 WARRANTY REPAIR INFORMATION WARRANTY ( WinSystems warrants to Customer that for a period of two (2) years from the date of shipment any Products and Software purchased or licensed hereunder which have been developed or manufactured by WinSystems shall be free of any material defects and shall perform substantially in accordance with WinSystems specifications therefore. With respect to any Products or Software purchased or licensed hereunder which have been developed or manufactured by others, WinSystems shall transfer and assign to Customer any warranty of such manufacturer or developer held by WinSystems, provided that the warranty, if any, may be assigned. Notwithstanding anything herein to the contrary, this warranty granted by WinSystems to the Customer shall be for the sole benefit of the Customer, and may not be assigned, transferred or conveyed to any third party. The sole obligation of WinSystems for any breach of warranty contained herein shall be, at its option, either (i) to repair or replace at its expense any materially defective Products or Software, or (ii) to take back such Products and Software and refund the Customer the purchase price and any license fees paid for the same. Customer shall pay all freight, duty, broker s fees, insurance charges for the return of any Products or Software to WinSystems under this warranty. WinSystems shall pay freight and insurance charges for any repaired or replaced Products or Software thereafter delivered to Customer within the United States. All fees and costs for shipment outside of the United States shall be paid by Customer. The foregoing warranty shall not apply to any Products of Software which have been subject to abuse, misuse, vandalism, accidents, alteration, neglect, unauthorized repair or improper installations. THERE ARE NO WARRANTIES BY WINSYSTEMS EXCEPT AS STATED HEREIN, THERE ARE NO OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN NO EVENT SHALL WINSYSTEMS BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF DATA, PROFITS OR GOODWILL. WINSYSTEMS MAXIMUM LIABILITY FOR ANY BREACH OF THIS AGREEMENT OR OTHER CLAIM RELATED TO ANY PRODUCTS, SOFTWARE, OR THE SUBJECT MATTER HEREOF, SHALL NOT EXCEED THE PURCHASE PRICE OR LICENSE FEE PAID BY CUSTOMER TO WINSYSTEMS FOR THE PRODUCTS OR SOFTWARE OR PORTION THEREOF TO WHICH SUCH BREACH OR CLAIM PERTAINS. WARRANTY SERVICE 1. To obtain service under this warranty, obtain a return authorization number. In the United States, contact the WinSystems Service Center for a return authorization number. Outside the United States, contact your local sales agent for a return authorization number. 2. You must send the product postage prepaid and insured. You must enclose the products in an anti-static bag to protect from damage by static electricity. WinSystems is not responsible for damage to the product due to static electricity OPERATIONS MANUAL PPM-WIRELESS 12